* [PATCH v2 0/2] serial: fsl_lpuart: fix DMA issues for 3.19
@ 2015-01-10 0:08 ` Stefan Agner
0 siblings, 0 replies; 14+ messages in thread
From: Stefan Agner @ 2015-01-10 0:08 UTC (permalink / raw)
To: linux-arm-kernel
This is patch 1 and 3 of the first version of this patchset.
Changes since v1:
- Reproduced on v3.19-rc3 and rebased ontop of that
- Make sure that RDMAS is cleared on startup
Stefan Agner (2):
serial: fsl_lpuart: delete timer on shutdown
serial: fsl_lpuart: avoid new transfer while DMA is running
drivers/tty/serial/fsl_lpuart.c | 16 +++++++++-------
1 file changed, 9 insertions(+), 7 deletions(-)
--
2.2.1
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2 1/2] serial: fsl_lpuart: delete timer on shutdown
2015-01-10 0:08 ` Stefan Agner
@ 2015-01-10 0:08 ` Stefan Agner
-1 siblings, 0 replies; 14+ messages in thread
From: Stefan Agner @ 2015-01-10 0:08 UTC (permalink / raw)
To: gregkh
Cc: jslaby, jingchang.lu, shawn.guo, linux-serial, linux-arm-kernel,
linux-kernel, stefan
If the serial port gets closed while a RX transfer is in progress,
the timer might fire after the serial port shutdown finished. This
leads in a NULL pointer dereference:
[ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 7.516590] pgd = 86348000
[ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
[ 7.526145] Internal error: Oops: 17 [#1] ARM
[ 7.530611] Modules linked in:
[ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
[ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
[ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
[ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
[ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
[ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
[ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
[ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
[ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
[ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
[ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
[ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
Setup the timer on UART startup which allows to delete the timer
unconditionally on shutdown. This also saves the initialization
on each transfer.
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
drivers/tty/serial/fsl_lpuart.c | 7 ++++---
1 file changed, 4 insertions(+), 3 deletions(-)
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index e7cde3a..29932b7 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -506,9 +506,6 @@ static inline void lpuart_prepare_rx(struct lpuart_port *sport)
spin_lock_irqsave(&sport->port.lock, flags);
- init_timer(&sport->lpuart_timer);
- sport->lpuart_timer.function = lpuart_timer_func;
- sport->lpuart_timer.data = (unsigned long)sport;
sport->lpuart_timer.expires = jiffies + sport->dma_rx_timeout;
add_timer(&sport->lpuart_timer);
@@ -1106,6 +1103,8 @@ static int lpuart_startup(struct uart_port *port)
sport->lpuart_dma_use = false;
} else {
sport->lpuart_dma_use = true;
+ setup_timer(&sport->lpuart_timer, lpuart_timer_func,
+ (unsigned long)sport);
temp = readb(port->membase + UARTCR5);
writeb(temp | UARTCR5_TDMAS, port->membase + UARTCR5);
}
@@ -1180,6 +1179,8 @@ static void lpuart_shutdown(struct uart_port *port)
devm_free_irq(port->dev, port->irq, sport);
if (sport->lpuart_dma_use) {
+ del_timer_sync(&sport->lpuart_timer);
+
lpuart_dma_tx_free(port);
lpuart_dma_rx_free(port);
}
--
2.2.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v2 1/2] serial: fsl_lpuart: delete timer on shutdown
@ 2015-01-10 0:08 ` Stefan Agner
0 siblings, 0 replies; 14+ messages in thread
From: Stefan Agner @ 2015-01-10 0:08 UTC (permalink / raw)
To: linux-arm-kernel
If the serial port gets closed while a RX transfer is in progress,
the timer might fire after the serial port shutdown finished. This
leads in a NULL pointer dereference:
[ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 7.516590] pgd = 86348000
[ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
[ 7.526145] Internal error: Oops: 17 [#1] ARM
[ 7.530611] Modules linked in:
[ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
[ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
[ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
[ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
[ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
[ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
[ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
[ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
[ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
[ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
[ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
[ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
Setup the timer on UART startup which allows to delete the timer
unconditionally on shutdown. This also saves the initialization
on each transfer.
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
drivers/tty/serial/fsl_lpuart.c | 7 ++++---
1 file changed, 4 insertions(+), 3 deletions(-)
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index e7cde3a..29932b7 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -506,9 +506,6 @@ static inline void lpuart_prepare_rx(struct lpuart_port *sport)
spin_lock_irqsave(&sport->port.lock, flags);
- init_timer(&sport->lpuart_timer);
- sport->lpuart_timer.function = lpuart_timer_func;
- sport->lpuart_timer.data = (unsigned long)sport;
sport->lpuart_timer.expires = jiffies + sport->dma_rx_timeout;
add_timer(&sport->lpuart_timer);
@@ -1106,6 +1103,8 @@ static int lpuart_startup(struct uart_port *port)
sport->lpuart_dma_use = false;
} else {
sport->lpuart_dma_use = true;
+ setup_timer(&sport->lpuart_timer, lpuart_timer_func,
+ (unsigned long)sport);
temp = readb(port->membase + UARTCR5);
writeb(temp | UARTCR5_TDMAS, port->membase + UARTCR5);
}
@@ -1180,6 +1179,8 @@ static void lpuart_shutdown(struct uart_port *port)
devm_free_irq(port->dev, port->irq, sport);
if (sport->lpuart_dma_use) {
+ del_timer_sync(&sport->lpuart_timer);
+
lpuart_dma_tx_free(port);
lpuart_dma_rx_free(port);
}
--
2.2.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v2 1/2] serial: fsl_lpuart: delete timer on shutdown
2015-01-10 0:08 ` Stefan Agner
@ 2015-01-10 0:48 ` Greg KH
-1 siblings, 0 replies; 14+ messages in thread
From: Greg KH @ 2015-01-10 0:48 UTC (permalink / raw)
To: Stefan Agner
Cc: jslaby, jingchang.lu, shawn.guo, linux-serial, linux-arm-kernel,
linux-kernel
On Sat, Jan 10, 2015 at 01:08:58AM +0100, Stefan Agner wrote:
> If the serial port gets closed while a RX transfer is in progress,
> the timer might fire after the serial port shutdown finished. This
> leads in a NULL pointer dereference:
>
> [ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
> [ 7.516590] pgd = 86348000
> [ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
> [ 7.526145] Internal error: Oops: 17 [#1] ARM
> [ 7.530611] Modules linked in:
> [ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
> [ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
> [ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
> [ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
> [ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
> [ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
> [ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
> [ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
> [ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
> [ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
> [ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
> [ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
> [ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
>
> Setup the timer on UART startup which allows to delete the timer
> unconditionally on shutdown. This also saves the initialization
> on each transfer.
>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
> drivers/tty/serial/fsl_lpuart.c | 7 ++++---
> 1 file changed, 4 insertions(+), 3 deletions(-)
Do stable kernels care about this as well, or is this just a regression
from 3.18?
thanks,
greg k-h
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2 1/2] serial: fsl_lpuart: delete timer on shutdown
@ 2015-01-10 0:48 ` Greg KH
0 siblings, 0 replies; 14+ messages in thread
From: Greg KH @ 2015-01-10 0:48 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Jan 10, 2015 at 01:08:58AM +0100, Stefan Agner wrote:
> If the serial port gets closed while a RX transfer is in progress,
> the timer might fire after the serial port shutdown finished. This
> leads in a NULL pointer dereference:
>
> [ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
> [ 7.516590] pgd = 86348000
> [ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
> [ 7.526145] Internal error: Oops: 17 [#1] ARM
> [ 7.530611] Modules linked in:
> [ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
> [ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
> [ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
> [ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
> [ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
> [ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
> [ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
> [ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
> [ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
> [ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
> [ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
> [ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
> [ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
>
> Setup the timer on UART startup which allows to delete the timer
> unconditionally on shutdown. This also saves the initialization
> on each transfer.
>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
> drivers/tty/serial/fsl_lpuart.c | 7 ++++---
> 1 file changed, 4 insertions(+), 3 deletions(-)
Do stable kernels care about this as well, or is this just a regression
from 3.18?
thanks,
greg k-h
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 1/2] serial: fsl_lpuart: delete timer on shutdown
2015-01-10 0:48 ` Greg KH
@ 2015-01-10 8:09 ` Stefan Agner
-1 siblings, 0 replies; 14+ messages in thread
From: Stefan Agner @ 2015-01-10 8:09 UTC (permalink / raw)
To: Greg KH
Cc: jslaby, jingchang.lu, shawn.guo, linux-serial, linux-arm-kernel,
linux-kernel
On 2015-01-10 01:48, Greg KH wrote:
> On Sat, Jan 10, 2015 at 01:08:58AM +0100, Stefan Agner wrote:
>> If the serial port gets closed while a RX transfer is in progress,
>> the timer might fire after the serial port shutdown finished. This
>> leads in a NULL pointer dereference:
>>
>> [ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
>> [ 7.516590] pgd = 86348000
>> [ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
>> [ 7.526145] Internal error: Oops: 17 [#1] ARM
>> [ 7.530611] Modules linked in:
>> [ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
>> [ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
>> [ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
>> [ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
>> [ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
>> [ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
>> [ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
>> [ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
>> [ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
>> [ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
>> [ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
>> [ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
>> [ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
>>
>> Setup the timer on UART startup which allows to delete the timer
>> unconditionally on shutdown. This also saves the initialization
>> on each transfer.
>>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> ---
>> drivers/tty/serial/fsl_lpuart.c | 7 ++++---
>> 1 file changed, 4 insertions(+), 3 deletions(-)
>
> Do stable kernels care about this as well, or is this just a regression
> from 3.18?
This is an issue since DMA support for lpuart was included in the
kernel, which was in 3.14.
--
Stefan
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2 1/2] serial: fsl_lpuart: delete timer on shutdown
@ 2015-01-10 8:09 ` Stefan Agner
0 siblings, 0 replies; 14+ messages in thread
From: Stefan Agner @ 2015-01-10 8:09 UTC (permalink / raw)
To: linux-arm-kernel
On 2015-01-10 01:48, Greg KH wrote:
> On Sat, Jan 10, 2015 at 01:08:58AM +0100, Stefan Agner wrote:
>> If the serial port gets closed while a RX transfer is in progress,
>> the timer might fire after the serial port shutdown finished. This
>> leads in a NULL pointer dereference:
>>
>> [ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
>> [ 7.516590] pgd = 86348000
>> [ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
>> [ 7.526145] Internal error: Oops: 17 [#1] ARM
>> [ 7.530611] Modules linked in:
>> [ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
>> [ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
>> [ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
>> [ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
>> [ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
>> [ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
>> [ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
>> [ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
>> [ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
>> [ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
>> [ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
>> [ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
>> [ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
>>
>> Setup the timer on UART startup which allows to delete the timer
>> unconditionally on shutdown. This also saves the initialization
>> on each transfer.
>>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> ---
>> drivers/tty/serial/fsl_lpuart.c | 7 ++++---
>> 1 file changed, 4 insertions(+), 3 deletions(-)
>
> Do stable kernels care about this as well, or is this just a regression
> from 3.18?
This is an issue since DMA support for lpuart was included in the
kernel, which was in 3.14.
--
Stefan
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2 2/2] serial: fsl_lpuart: avoid new transfer while DMA is running
2015-01-10 0:08 ` Stefan Agner
@ 2015-01-10 0:08 ` Stefan Agner
-1 siblings, 0 replies; 14+ messages in thread
From: Stefan Agner @ 2015-01-10 0:08 UTC (permalink / raw)
To: gregkh
Cc: jslaby, jingchang.lu, shawn.guo, linux-serial, linux-arm-kernel,
linux-kernel, stefan
When the UART is in DMA receive mode (RDMAS set) and one character
just arrived while another interrupt is handled (e.g. TX), the RDRF
(receiver data register full flag) is set due to the water level of
1. But since the DMA will take care of this character, there is no
need to handle it by calling lpuart_prepare_rx. Handling it leads to
adding the RX timeout timer twice:
[ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
[ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
[ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
[ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
[ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
[ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
[ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
[ 74.373960] LR is at lpuart_int+0x15c/0x3d8
[ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
[ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
[ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
[ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
[ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
[ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
[ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
...
Solve this by only execute the receiver path (lpuart_prepare_rx) if
the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
cleared on initialization, in case it has been left set.
This can be best reproduced using UART as a serial console, then
running top while dd'ing data into the terminal.
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
drivers/tty/serial/fsl_lpuart.c | 9 +++++----
1 file changed, 5 insertions(+), 4 deletions(-)
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index 29932b7..e95c497 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -755,18 +755,18 @@ out:
static irqreturn_t lpuart_int(int irq, void *dev_id)
{
struct lpuart_port *sport = dev_id;
- unsigned char sts;
+ unsigned char sts, crdma;
sts = readb(sport->port.membase + UARTSR1);
+ crdma = readb(sport->port.membase + UARTCR5);
- if (sts & UARTSR1_RDRF) {
+ if (sts & UARTSR1_RDRF && !(crdma & UARTCR5_RDMAS)) {
if (sport->lpuart_dma_use)
lpuart_prepare_rx(sport);
else
lpuart_rxint(irq, dev_id);
}
- if (sts & UARTSR1_TDRE &&
- !(readb(sport->port.membase + UARTCR5) & UARTCR5_TDMAS)) {
+ if (sts & UARTSR1_TDRE && !(crdma & UARTCR5_TDMAS)) {
if (sport->lpuart_dma_use)
lpuart_pio_tx(sport);
else
@@ -1106,6 +1106,7 @@ static int lpuart_startup(struct uart_port *port)
setup_timer(&sport->lpuart_timer, lpuart_timer_func,
(unsigned long)sport);
temp = readb(port->membase + UARTCR5);
+ temp &= ~UARTCR5_RDMAS;
writeb(temp | UARTCR5_TDMAS, port->membase + UARTCR5);
}
--
2.2.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v2 2/2] serial: fsl_lpuart: avoid new transfer while DMA is running
@ 2015-01-10 0:08 ` Stefan Agner
0 siblings, 0 replies; 14+ messages in thread
From: Stefan Agner @ 2015-01-10 0:08 UTC (permalink / raw)
To: linux-arm-kernel
When the UART is in DMA receive mode (RDMAS set) and one character
just arrived while another interrupt is handled (e.g. TX), the RDRF
(receiver data register full flag) is set due to the water level of
1. But since the DMA will take care of this character, there is no
need to handle it by calling lpuart_prepare_rx. Handling it leads to
adding the RX timeout timer twice:
[ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
[ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
[ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
[ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
[ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
[ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
[ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
[ 74.373960] LR is at lpuart_int+0x15c/0x3d8
[ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
[ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
[ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
[ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
[ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
[ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
[ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
...
Solve this by only execute the receiver path (lpuart_prepare_rx) if
the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
cleared on initialization, in case it has been left set.
This can be best reproduced using UART as a serial console, then
running top while dd'ing data into the terminal.
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
drivers/tty/serial/fsl_lpuart.c | 9 +++++----
1 file changed, 5 insertions(+), 4 deletions(-)
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index 29932b7..e95c497 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -755,18 +755,18 @@ out:
static irqreturn_t lpuart_int(int irq, void *dev_id)
{
struct lpuart_port *sport = dev_id;
- unsigned char sts;
+ unsigned char sts, crdma;
sts = readb(sport->port.membase + UARTSR1);
+ crdma = readb(sport->port.membase + UARTCR5);
- if (sts & UARTSR1_RDRF) {
+ if (sts & UARTSR1_RDRF && !(crdma & UARTCR5_RDMAS)) {
if (sport->lpuart_dma_use)
lpuart_prepare_rx(sport);
else
lpuart_rxint(irq, dev_id);
}
- if (sts & UARTSR1_TDRE &&
- !(readb(sport->port.membase + UARTCR5) & UARTCR5_TDMAS)) {
+ if (sts & UARTSR1_TDRE && !(crdma & UARTCR5_TDMAS)) {
if (sport->lpuart_dma_use)
lpuart_pio_tx(sport);
else
@@ -1106,6 +1106,7 @@ static int lpuart_startup(struct uart_port *port)
setup_timer(&sport->lpuart_timer, lpuart_timer_func,
(unsigned long)sport);
temp = readb(port->membase + UARTCR5);
+ temp &= ~UARTCR5_RDMAS;
writeb(temp | UARTCR5_TDMAS, port->membase + UARTCR5);
}
--
2.2.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v2 2/2] serial: fsl_lpuart: avoid new transfer while DMA is running
2015-01-10 0:08 ` Stefan Agner
@ 2015-01-10 0:49 ` Greg KH
-1 siblings, 0 replies; 14+ messages in thread
From: Greg KH @ 2015-01-10 0:49 UTC (permalink / raw)
To: Stefan Agner
Cc: jslaby, jingchang.lu, shawn.guo, linux-serial, linux-arm-kernel,
linux-kernel
On Sat, Jan 10, 2015 at 01:08:59AM +0100, Stefan Agner wrote:
> When the UART is in DMA receive mode (RDMAS set) and one character
> just arrived while another interrupt is handled (e.g. TX), the RDRF
> (receiver data register full flag) is set due to the water level of
> 1. But since the DMA will take care of this character, there is no
> need to handle it by calling lpuart_prepare_rx. Handling it leads to
> adding the RX timeout timer twice:
>
> [ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
> [ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
> [ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
> [ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
> [ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
> [ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
> [ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
> [ 74.373960] LR is at lpuart_int+0x15c/0x3d8
> [ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
> [ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
> [ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
> [ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
> [ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
> [ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
> [ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
> [ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
> ...
>
> Solve this by only execute the receiver path (lpuart_prepare_rx) if
> the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
> cleared on initialization, in case it has been left set.
>
> This can be best reproduced using UART as a serial console, then
> running top while dd'ing data into the terminal.
>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
> drivers/tty/serial/fsl_lpuart.c | 9 +++++----
> 1 file changed, 5 insertions(+), 4 deletions(-)
Same stable question as before.
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2 2/2] serial: fsl_lpuart: avoid new transfer while DMA is running
@ 2015-01-10 0:49 ` Greg KH
0 siblings, 0 replies; 14+ messages in thread
From: Greg KH @ 2015-01-10 0:49 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Jan 10, 2015 at 01:08:59AM +0100, Stefan Agner wrote:
> When the UART is in DMA receive mode (RDMAS set) and one character
> just arrived while another interrupt is handled (e.g. TX), the RDRF
> (receiver data register full flag) is set due to the water level of
> 1. But since the DMA will take care of this character, there is no
> need to handle it by calling lpuart_prepare_rx. Handling it leads to
> adding the RX timeout timer twice:
>
> [ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
> [ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
> [ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
> [ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
> [ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
> [ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
> [ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
> [ 74.373960] LR is at lpuart_int+0x15c/0x3d8
> [ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
> [ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
> [ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
> [ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
> [ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
> [ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
> [ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
> [ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
> ...
>
> Solve this by only execute the receiver path (lpuart_prepare_rx) if
> the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
> cleared on initialization, in case it has been left set.
>
> This can be best reproduced using UART as a serial console, then
> running top while dd'ing data into the terminal.
>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
> drivers/tty/serial/fsl_lpuart.c | 9 +++++----
> 1 file changed, 5 insertions(+), 4 deletions(-)
Same stable question as before.
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 2/2] serial: fsl_lpuart: avoid new transfer while DMA is running
2015-01-10 0:49 ` Greg KH
@ 2015-01-10 8:12 ` Stefan Agner
-1 siblings, 0 replies; 14+ messages in thread
From: Stefan Agner @ 2015-01-10 8:12 UTC (permalink / raw)
To: Greg KH
Cc: jslaby, jingchang.lu, shawn.guo, linux-serial, linux-arm-kernel,
linux-kernel
On 2015-01-10 01:49, Greg KH wrote:
> On Sat, Jan 10, 2015 at 01:08:59AM +0100, Stefan Agner wrote:
>> When the UART is in DMA receive mode (RDMAS set) and one character
>> just arrived while another interrupt is handled (e.g. TX), the RDRF
>> (receiver data register full flag) is set due to the water level of
>> 1. But since the DMA will take care of this character, there is no
>> need to handle it by calling lpuart_prepare_rx. Handling it leads to
>> adding the RX timeout timer twice:
>>
>> [ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
>> [ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
>> [ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
>> [ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
>> [ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
>> [ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
>> [ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
>> [ 74.373960] LR is at lpuart_int+0x15c/0x3d8
>> [ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
>> [ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
>> [ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
>> [ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
>> [ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
>> [ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
>> [ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
>> [ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
>> ...
>>
>> Solve this by only execute the receiver path (lpuart_prepare_rx) if
>> the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
>> cleared on initialization, in case it has been left set.
>>
>> This can be best reproduced using UART as a serial console, then
>> running top while dd'ing data into the terminal.
>>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> ---
>> drivers/tty/serial/fsl_lpuart.c | 9 +++++----
>> 1 file changed, 5 insertions(+), 4 deletions(-)
>
> Same stable question as before.
The same here, an issue since 3.14....
--
Stefan
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2 2/2] serial: fsl_lpuart: avoid new transfer while DMA is running
@ 2015-01-10 8:12 ` Stefan Agner
0 siblings, 0 replies; 14+ messages in thread
From: Stefan Agner @ 2015-01-10 8:12 UTC (permalink / raw)
To: linux-arm-kernel
On 2015-01-10 01:49, Greg KH wrote:
> On Sat, Jan 10, 2015 at 01:08:59AM +0100, Stefan Agner wrote:
>> When the UART is in DMA receive mode (RDMAS set) and one character
>> just arrived while another interrupt is handled (e.g. TX), the RDRF
>> (receiver data register full flag) is set due to the water level of
>> 1. But since the DMA will take care of this character, there is no
>> need to handle it by calling lpuart_prepare_rx. Handling it leads to
>> adding the RX timeout timer twice:
>>
>> [ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
>> [ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
>> [ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
>> [ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
>> [ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
>> [ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
>> [ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
>> [ 74.373960] LR is at lpuart_int+0x15c/0x3d8
>> [ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
>> [ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
>> [ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
>> [ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
>> [ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
>> [ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
>> [ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
>> [ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
>> ...
>>
>> Solve this by only execute the receiver path (lpuart_prepare_rx) if
>> the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
>> cleared on initialization, in case it has been left set.
>>
>> This can be best reproduced using UART as a serial console, then
>> running top while dd'ing data into the terminal.
>>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> ---
>> drivers/tty/serial/fsl_lpuart.c | 9 +++++----
>> 1 file changed, 5 insertions(+), 4 deletions(-)
>
> Same stable question as before.
The same here, an issue since 3.14....
--
Stefan
^ permalink raw reply [flat|nested] 14+ messages in thread