From: Maxime Ripard <maxime.ripard@free-electrons.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 07/15] sunxi_nand_spl: Turn off clocks when we're done with the nand
Date: Wed, 19 Aug 2015 15:48:07 +0200 [thread overview]
Message-ID: <20150819134807.GF30520@lukather> (raw)
In-Reply-To: <1439668968-3882-8-git-send-email-hdegoede@redhat.com>
On Sat, Aug 15, 2015 at 10:02:40PM +0200, Hans de Goede wrote:
> Turn off the nand and dma clocks when we're done with the nand, this
> puts the nand and dma controllers back into a clean state for when the
> kernel boots.
>
> Without this the kernel will not boot properly when it is build with
> dma-controller support.
The kernel shouldn't behave like that. What issue are you seeing?
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150819/d3d18c5e/attachment.sig>
next prev parent reply other threads:[~2015-08-19 13:48 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-08-15 20:02 [U-Boot] [PATCH 00/15] sunxi_nand_spl: cleanups, auto config and bad block handling Hans de Goede
2015-08-15 20:02 ` [U-Boot] [PATCH 01/15] sunxi_nand_spl: Fix CONFIG_SPL_NAND_SUNXI handling Hans de Goede
2015-08-17 8:11 ` Ian Campbell
2015-08-19 13:45 ` Maxime Ripard
2015-08-20 6:33 ` Hans de Goede
2015-08-27 12:36 ` Maxime Ripard
2015-08-15 20:02 ` [U-Boot] [PATCH 02/15] sunxi_nand_spl: Drop unnecessary temp buf Hans de Goede
2015-08-17 7:22 ` Chen-Yu Tsai
2015-08-17 8:14 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 03/15] sunxi_nand_spl: We only need to reset the nand chip once Hans de Goede
2015-08-17 8:14 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 04/15] sunxi_nand_spl: Do not bother writing the spare-area reg in syndrome mode Hans de Goede
2015-08-17 8:19 ` Ian Campbell
2015-08-17 8:59 ` Hans de Goede
2015-08-17 11:28 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 05/15] sunxi_nand_spl: Use SYS_NAND_SELF_INIT and only do nand init when necessary Hans de Goede
2015-08-17 8:20 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 06/15] sunxi_nand_spl: Make sure the DMA controller is enabled Hans de Goede
2015-08-17 8:21 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 07/15] sunxi_nand_spl: Turn off clocks when we're done with the nand Hans de Goede
2015-08-17 8:22 ` Ian Campbell
2015-08-19 13:48 ` Maxime Ripard [this message]
2015-08-20 6:35 ` Hans de Goede
2015-08-24 14:54 ` Maxime Ripard
2015-08-15 20:02 ` [U-Boot] [PATCH 08/15] sunxi_nand_spl: Add proper cache flusing Hans de Goede
2015-08-17 8:22 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 09/15] sunxi_nand_spl: Use kernel driver algorithm for determining ecc_mode / _off Hans de Goede
2015-08-17 8:24 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 10/15] sunxi_nand_spl: Remove NAND_SUNXI_SPL_SYNDROME_PARTITIONS_END Hans de Goede
2015-08-17 8:27 ` Ian Campbell
2015-08-17 9:05 ` Hans de Goede
2015-08-15 20:02 ` [U-Boot] [PATCH 11/15] sunxi_nand_spl: Add support for sun4i and sun5i SoCs Hans de Goede
2015-08-17 8:29 ` Ian Campbell
2015-08-17 8:31 ` Hans de Goede
2015-08-17 8:35 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 12/15] sunxi_nand_spl: Properly config page-size in the nand ctl register Hans de Goede
2015-08-17 8:29 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 13/15] sunxi_nand_spl: Parametrize lowlevel read functions Hans de Goede
2015-08-17 8:31 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 14/15] sunxi_nand_spl: Auto detect nand configuration parameters Hans de Goede
2015-08-17 8:32 ` Ian Campbell
2015-08-15 20:02 ` [U-Boot] [PATCH 15/15] sunxi_nand_spl: Add support for backup boot partitions Hans de Goede
2015-08-17 8:34 ` Ian Campbell
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150819134807.GF30520@lukather \
--to=maxime.ripard@free-electrons.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.