From: Michael Turquette <mturquette@baylibre.com>
To: Wenyou Yang <wenyou.yang@atmel.com>,
"Nicolas Ferre" <nicolas.ferre@atmel.com>,
"Alexandre Belloni" <alexandre.belloni@free-electrons.com>,
"Jean-Christophe Plagniol-Villard" <plagnioj@jcrosoft.com>
Cc: "Russell King" <linux@arm.linux.org.uk>,
"Stephen Boyd" <sboyd@codeaurora.org>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
"Wenyou Yang" <wenyou.yang@atmel.com>
Subject: Re: [PATCH 2/2] ARM: at91/pm: add ultra Low-power mode 1(ULP1) support
Date: Thu, 15 Oct 2015 02:31:46 -0700 [thread overview]
Message-ID: <20151015093146.7777.781@quantum> (raw)
In-Reply-To: <1444880467-18598-3-git-send-email-wenyou.yang@atmel.com>
Quoting Wenyou Yang (2015-10-14 20:41:07)
> The Ultra Low-power mode 1(ULP1) is introduced by SAMA5D2.
> =
> In the ULP1 mode, all the clocks are shut off, inclusive the embedded
> 12MHz RC oscillator, so as to achieve the lowest power consumption
> with the system in retention mode and able to resume on the wake up
> events. As soon as the wake up event is asserted, the embedded 12MHz
> RC oscillator restarts automatically.
> =
> The number of wake up sources for the ULP1 mode is limited, the wake
> up sources should be configured via the PMC_FSMR and PMC_FSPR
> registers.
> =
> In this patch, the following wake up sources are enabled,
> - WKUP0 pin
> - WKUP1 pin to WKUP8 pin (shared with PIOBU0 to PIOBU7)
> - RTC alarm
> =
> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
For the changes to the clk header:
Acked-by: Michael Turquette <mturquette@baylibre.com>
> ---
> =
> arch/arm/mach-at91/pm.c | 29 ++++++++++
> arch/arm/mach-at91/pm.h | 7 +++
> arch/arm/mach-at91/pm_suspend.S | 111 +++++++++++++++++++++++++++++++++=
++++++
> include/linux/clk/at91_pmc.h | 36 +++++++++++++
> 4 files changed, 183 insertions(+)
> =
> diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
> index 80e277c..49443d9 100644
> --- a/arch/arm/mach-at91/pm.c
> +++ b/arch/arm/mach-at91/pm.c
> @@ -35,6 +35,11 @@
> #include "generic.h"
> #include "pm.h"
> =
> +#define ULP0_MODE 0x00
> +#define ULP1_MODE 0x11
> +
> +#define SAMA5D2_PMC_VERSION 0x20540
> +
> /*
> * FIXME: this is needed to communicate between the pinctrl driver and
> * the PM implementation in the machine. Possibly part of the PM
> @@ -64,6 +69,23 @@ static int at91_pm_valid_state(suspend_state_t state)
> }
> }
> =
> +static void at91_config_ulp1_wkup_source(void)
> +{
> + if (at91_pmc_read(AT91_PMC_VERSION) >=3D SAMA5D2_PMC_VERSION) {
> + at91_pmc_write(AT91_PMC_FSMR, AT91_PMC_RTCAL |
> + AT91_PMC_FSTT9 |
> + AT91_PMC_FSTT8 |
> + AT91_PMC_FSTT7 |
> + AT91_PMC_FSTT6 |
> + AT91_PMC_FSTT5 |
> + AT91_PMC_FSTT4 |
> + AT91_PMC_FSTT3 |
> + AT91_PMC_FSTT2 |
> + AT91_PMC_FSTT0);
> +
> + at91_pmc_write(AT91_PMC_FSPR, 0);
> + }
> +}
> =
> static suspend_state_t target_state;
> =
> @@ -73,6 +95,9 @@ static suspend_state_t target_state;
> static int at91_pm_begin(suspend_state_t state)
> {
> target_state =3D state;
> +
> + at91_config_ulp1_wkup_source();
> +
> return 0;
> }
> =
> @@ -140,6 +165,10 @@ static void at91_pm_suspend(suspend_state_t state)
> pm_data |=3D (state =3D=3D PM_SUSPEND_MEM) ?
> AT91_PM_MODE(AT91_PM_SLOW_CLOCK) : 0;
> =
> + pm_data |=3D ((state =3D=3D PM_SUSPEND_MEM) &&
> + (at91_pmc_read(AT91_PMC_VERSION) >=3D SAMA5D2_PMC_VER=
SION)) ?
> + AT91_PM_ULP(AT91_PM_ULP1_MODE) : 0;
> +
> flush_cache_all();
> outer_disable();
> =
> diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
> index 3fcf881..2e76745 100644
> --- a/arch/arm/mach-at91/pm.h
> +++ b/arch/arm/mach-at91/pm.h
> @@ -39,4 +39,11 @@ extern void __iomem *at91_ramc_base[];
> =
> #define AT91_PM_SLOW_CLOCK 0x01
> =
> +#define AT91_PM_ULP_OFFSET 5
> +#define AT91_PM_ULP_MASK 0x03
> +#define AT91_PM_ULP(x) (((x) & AT91_PM_ULP_MASK) << AT91_PM_ULP_=
OFFSET)
> +
> +#define AT91_PM_ULP0_MODE 0x00
> +#define AT91_PM_ULP1_MODE 0x01
> +
> #endif
> diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_susp=
end.S
> index 825347b..543c430 100644
> --- a/arch/arm/mach-at91/pm_suspend.S
> +++ b/arch/arm/mach-at91/pm_suspend.S
> @@ -41,6 +41,15 @@ tmp2 .req r5
> .endm
> =
> /*
> + * Wait for main oscillator selection is done
> + */
> + .macro wait_moscsels
> +1: ldr tmp1, [pmc, #AT91_PMC_SR]
> + tst tmp1, #AT91_PMC_MOSCSELS
> + beq 1b
> + .endm
> +
> +/*
> * Wait until PLLA has locked.
> */
> .macro wait_pllalock
> @@ -99,6 +108,10 @@ ENTRY(at91_pm_suspend_in_sram)
> and r0, r0, #AT91_PM_MODE_MASK
> str r0, .pm_mode
> =
> + lsr r0, r3, #AT91_PM_ULP_OFFSET
> + and r0, r0, #AT91_PM_ULP_MASK
> + str r0, .ulp_mode
> +
> /* Active the self-refresh mode */
> mov r0, #SRAMC_SELF_FRESH_ACTIVE
> bl at91_sramc_self_refresh
> @@ -107,6 +120,14 @@ ENTRY(at91_pm_suspend_in_sram)
> tst r0, #AT91_PM_SLOW_CLOCK
> beq standby_mode
> =
> + ldr r0, .ulp_mode
> + tst r0, #AT91_PM_ULP1_MODE
> + beq ulp0_mode
> +
> +ulp1_mode:
> + bl at91_pm_ulp1_mode
> + b pm_exit
> +
> ulp0_mode:
> bl at91_pm_ulp0_mode
> b pm_exit
> @@ -313,6 +334,94 @@ ENTRY(at91_pm_ulp0_mode)
> mov pc, lr
> ENDPROC(at91_pm_ulp0_mode)
> =
> +/*
> + * void at91_pm_ulp1_mode(void)
> + *
> + */
> +ENTRY(at91_pm_ulp1_mode)
> + ldr pmc, .pmc_base
> +
> + /* Save PMC_MCKR config */
> + ldr tmp1, [pmc, #AT91_PMC_MCKR]
> + str tmp1, .saved_mckr
> +
> + /* Switch the master clock source to main clock */
> + bic tmp1, tmp1, #AT91_PMC_CSS
> + orr tmp1, tmp1, #AT91_PMC_CSS_MAIN
> + str tmp1, [pmc, #AT91_PMC_MCKR]
> +
> + wait_mckrdy
> +
> + /* Save PLLA config, then and disable PLLA */
> + ldr tmp1, [pmc, #AT91_CKGR_PLLAR]
> + str tmp1, .saved_pllar
> +
> + bic tmp1, tmp1, #AT91_PMC3_MUL
> + str tmp1, [pmc, #AT91_CKGR_PLLAR]
> +
> + /* Switch main clock to 12-MHz RC oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + bic tmp1, tmp1, #AT91_PMC_MOSCSEL
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_moscsels
> +
> + /* Disable the main oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + bic tmp1, tmp1, #AT91_PMC_MOSCEN
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + /* Enter the ULP1 mode by setting WAITMODE bit in CKGR_MOR */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + orr tmp1, tmp1, #AT91_PMC_WAITMODE
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_mckrdy
> +
> + /* Enable the main oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + orr tmp1, tmp1, #AT91_PMC_MOSCEN
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_moscrdy
> +
> + /* Switch main clock to the main oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + orr tmp1, tmp1, #AT91_PMC_MOSCSEL
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_moscsels
> +
> + /* Restore PLLA config */
> + ldr tmp1, .saved_pllar
> + str tmp1, [pmc, #AT91_CKGR_PLLAR]
> +
> + wait_pllalock
> +
> + /* Restore PMC_MCKR config */
> + ldr tmp1, .saved_mckr
> + str tmp1, [pmc, #AT91_PMC_MCKR]
> +
> + wait_mckrdy
> +
> + mov pc, lr
> +ENDPROC(at91_pm_ulp1_mode)
> +
> .pmc_base:
> .word 0
> .sramc_base:
> @@ -323,6 +432,8 @@ ENDPROC(at91_pm_ulp0_mode)
> .word 0
> .pm_mode:
> .word 0
> +.ulp_mode:
> + .word 0
> .saved_mckr:
> .word 0
> .saved_pllar:
> diff --git a/include/linux/clk/at91_pmc.h b/include/linux/clk/at91_pmc.h
> index 7669f76..3dc4e60 100644
> --- a/include/linux/clk/at91_pmc.h
> +++ b/include/linux/clk/at91_pmc.h
> @@ -59,8 +59,10 @@ extern void __iomem *at91_pmc_base;
> #define AT91_CKGR_MOR 0x20 /* Main O=
scillator Register [not on SAM9RL] */
> #define AT91_PMC_MOSCEN (1 << 0) /=
* Main Oscillator Enable */
> #define AT91_PMC_OSCBYPASS (1 << 1) /=
* Oscillator Bypass */
> +#define AT91_PMC_WAITMODE (1 << 2) /=
* Wait Mode Command */
> #define AT91_PMC_MOSCRCEN (1 << 3) /=
* Main On-Chip RC Oscillator Enable [some SAM9] */
> #define AT91_PMC_OSCOUNT (0xff << 8) /=
* Main Oscillator Start-up Time */
> +#define AT91_PMC_KEY_MASK (0xff << 16)
> #define AT91_PMC_KEY (0x37 << 16) /=
* MOR Writing Key */
> #define AT91_PMC_MOSCSEL (1 << 24) /=
* Main Oscillator Selection [some SAM9] */
> #define AT91_PMC_CFDEN (1 << 25) /=
* Clock Failure Detector Enable [some SAM9] */
> @@ -166,6 +168,38 @@ extern void __iomem *at91_pmc_base;
> #define AT91_PMC_CFDEV (1 << 18) /=
* Clock Failure Detector Event [some SAM9] */
> #define AT91_PMC_IMR 0x6c /* Interr=
upt Mask Register */
> =
> +#define AT91_PMC_FSMR 0x70 /* Fast Startup M=
ode Register */
> +#define AT91_PMC_FSTT0 (1 << 0) /=
* Fast Startup from WKUP Pin Enable */
> +#define AT91_PMC_FSTT1 (1 << 1) /=
* Fast Startup from Security Module Enable */
> +#define AT91_PMC_FSTT2 (1 << 2) /=
* Fast Startup from PIOBU0 Input Enable */
> +#define AT91_PMC_FSTT3 (1 << 3) /=
* Fast Startup from PIOBU1 Input Enable */
> +#define AT91_PMC_FSTT4 (1 << 4) /=
* Fast Startup from PIOBU2 Input Enable */
> +#define AT91_PMC_FSTT5 (1 << 5) /=
* Fast Startup from PIOBU3 Input Enable */
> +#define AT91_PMC_FSTT6 (1 << 6) /=
* Fast Startup from PIOBU4 Input Enable */
> +#define AT91_PMC_FSTT7 (1 << 7) /=
* Fast Startup from PIOBU5 Input Enable */
> +#define AT91_PMC_FSTT8 (1 << 8) /=
* Fast Startup from PIOBU6 Input Enable */
> +#define AT91_PMC_FSTT9 (1 << 9) /=
* Fast Startup from PIOBU7 Input Enable */
> +#define AT91_PMC_FSTT10 (1 << 10) /=
* Fast Startup from GMAC Wake-up On LAN Enable */
> +#define AT91_PMC_RTCAL (1 << 17) /=
* Fast Startup from RTC Alarm Enable */
> +#define AT91_PMC_USBAL (1 << 18) /=
* Fast Startup from USB Resume Enable */
> +#define AT91_PMC_SDMMC_CD (1 << 19) /=
* Fast Startup from SDMMC Card Detect Enable */
> +#define AT91_PMC_LPM (1 << 20) /=
* Low-power Mode */
> +#define AT91_PMC_RXLP_MCE (1 << 24) /=
* Fast Startup from Backup UART Receive Match Condition Enable */
> +#define AT91_PMC_ACC_CE (1 << 25) /=
* Fast Startup from Analog Comparator Controller Comparison Enable*/
> +
> +#define AT91_PMC_FSPR 0x74 /* Fast Startup P=
olarity Register */
> +#define AT91_PMC_FSTP0 (1 << 0) /=
* WKUP Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP1 (1 << 1) /=
* Security Module Polarity for Fast Startup */
> +#define AT91_PMC_FSTP2 (1 << 2) /=
* PIOBU0 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP3 (1 << 3) /=
* PIOBU1 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP4 (1 << 4) /=
* PIOBU2 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP5 (1 << 5) /=
* PIOBU3 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP6 (1 << 6) /=
* PIOBU4 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP7 (1 << 7) /=
* PIOBU5 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP8 (1 << 8) /=
* PIOBU6 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP9 (1 << 9) /=
* PIOBU7 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP10 (1 << 10) /=
* GMAC Wake-up On LAN Polarity for Fast Startup */
> +
> #define AT91_PMC_PLLICPR 0x80 /* PLL Charge Pum=
p Current Register */
> =
> #define AT91_PMC_PROT 0xe4 /* Write Protect =
Mode Register [some SAM9] */
> @@ -177,6 +211,8 @@ extern void __iomem *at91_pmc_base;
> #define AT91_PMC_WPVS (0x1 << 0) /=
* Write Protect Violation Status */
> #define AT91_PMC_WPVSRC (0xffff << 8) /=
* Write Protect Violation Source */
> =
> +#define AT91_PMC_VERSION 0xfc
> +
> #define AT91_PMC_PCER1 0x100 /* Peripheral Clo=
ck Enable Register 1 [SAMA5 only]*/
> #define AT91_PMC_PCDR1 0x104 /* Peripheral Clo=
ck Enable Register 1 */
> #define AT91_PMC_PCSR1 0x108 /* Peripheral Clo=
ck Enable Register 1 */
> -- =
> 1.7.9.5
>=20
WARNING: multiple messages have this Message-ID (diff)
From: mturquette@baylibre.com (Michael Turquette)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/2] ARM: at91/pm: add ultra Low-power mode 1(ULP1) support
Date: Thu, 15 Oct 2015 02:31:46 -0700 [thread overview]
Message-ID: <20151015093146.7777.781@quantum> (raw)
In-Reply-To: <1444880467-18598-3-git-send-email-wenyou.yang@atmel.com>
Quoting Wenyou Yang (2015-10-14 20:41:07)
> The Ultra Low-power mode 1(ULP1) is introduced by SAMA5D2.
>
> In the ULP1 mode, all the clocks are shut off, inclusive the embedded
> 12MHz RC oscillator, so as to achieve the lowest power consumption
> with the system in retention mode and able to resume on the wake up
> events. As soon as the wake up event is asserted, the embedded 12MHz
> RC oscillator restarts automatically.
>
> The number of wake up sources for the ULP1 mode is limited, the wake
> up sources should be configured via the PMC_FSMR and PMC_FSPR
> registers.
>
> In this patch, the following wake up sources are enabled,
> - WKUP0 pin
> - WKUP1 pin to WKUP8 pin (shared with PIOBU0 to PIOBU7)
> - RTC alarm
>
> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
For the changes to the clk header:
Acked-by: Michael Turquette <mturquette@baylibre.com>
> ---
>
> arch/arm/mach-at91/pm.c | 29 ++++++++++
> arch/arm/mach-at91/pm.h | 7 +++
> arch/arm/mach-at91/pm_suspend.S | 111 +++++++++++++++++++++++++++++++++++++++
> include/linux/clk/at91_pmc.h | 36 +++++++++++++
> 4 files changed, 183 insertions(+)
>
> diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
> index 80e277c..49443d9 100644
> --- a/arch/arm/mach-at91/pm.c
> +++ b/arch/arm/mach-at91/pm.c
> @@ -35,6 +35,11 @@
> #include "generic.h"
> #include "pm.h"
>
> +#define ULP0_MODE 0x00
> +#define ULP1_MODE 0x11
> +
> +#define SAMA5D2_PMC_VERSION 0x20540
> +
> /*
> * FIXME: this is needed to communicate between the pinctrl driver and
> * the PM implementation in the machine. Possibly part of the PM
> @@ -64,6 +69,23 @@ static int at91_pm_valid_state(suspend_state_t state)
> }
> }
>
> +static void at91_config_ulp1_wkup_source(void)
> +{
> + if (at91_pmc_read(AT91_PMC_VERSION) >= SAMA5D2_PMC_VERSION) {
> + at91_pmc_write(AT91_PMC_FSMR, AT91_PMC_RTCAL |
> + AT91_PMC_FSTT9 |
> + AT91_PMC_FSTT8 |
> + AT91_PMC_FSTT7 |
> + AT91_PMC_FSTT6 |
> + AT91_PMC_FSTT5 |
> + AT91_PMC_FSTT4 |
> + AT91_PMC_FSTT3 |
> + AT91_PMC_FSTT2 |
> + AT91_PMC_FSTT0);
> +
> + at91_pmc_write(AT91_PMC_FSPR, 0);
> + }
> +}
>
> static suspend_state_t target_state;
>
> @@ -73,6 +95,9 @@ static suspend_state_t target_state;
> static int at91_pm_begin(suspend_state_t state)
> {
> target_state = state;
> +
> + at91_config_ulp1_wkup_source();
> +
> return 0;
> }
>
> @@ -140,6 +165,10 @@ static void at91_pm_suspend(suspend_state_t state)
> pm_data |= (state == PM_SUSPEND_MEM) ?
> AT91_PM_MODE(AT91_PM_SLOW_CLOCK) : 0;
>
> + pm_data |= ((state == PM_SUSPEND_MEM) &&
> + (at91_pmc_read(AT91_PMC_VERSION) >= SAMA5D2_PMC_VERSION)) ?
> + AT91_PM_ULP(AT91_PM_ULP1_MODE) : 0;
> +
> flush_cache_all();
> outer_disable();
>
> diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
> index 3fcf881..2e76745 100644
> --- a/arch/arm/mach-at91/pm.h
> +++ b/arch/arm/mach-at91/pm.h
> @@ -39,4 +39,11 @@ extern void __iomem *at91_ramc_base[];
>
> #define AT91_PM_SLOW_CLOCK 0x01
>
> +#define AT91_PM_ULP_OFFSET 5
> +#define AT91_PM_ULP_MASK 0x03
> +#define AT91_PM_ULP(x) (((x) & AT91_PM_ULP_MASK) << AT91_PM_ULP_OFFSET)
> +
> +#define AT91_PM_ULP0_MODE 0x00
> +#define AT91_PM_ULP1_MODE 0x01
> +
> #endif
> diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S
> index 825347b..543c430 100644
> --- a/arch/arm/mach-at91/pm_suspend.S
> +++ b/arch/arm/mach-at91/pm_suspend.S
> @@ -41,6 +41,15 @@ tmp2 .req r5
> .endm
>
> /*
> + * Wait for main oscillator selection is done
> + */
> + .macro wait_moscsels
> +1: ldr tmp1, [pmc, #AT91_PMC_SR]
> + tst tmp1, #AT91_PMC_MOSCSELS
> + beq 1b
> + .endm
> +
> +/*
> * Wait until PLLA has locked.
> */
> .macro wait_pllalock
> @@ -99,6 +108,10 @@ ENTRY(at91_pm_suspend_in_sram)
> and r0, r0, #AT91_PM_MODE_MASK
> str r0, .pm_mode
>
> + lsr r0, r3, #AT91_PM_ULP_OFFSET
> + and r0, r0, #AT91_PM_ULP_MASK
> + str r0, .ulp_mode
> +
> /* Active the self-refresh mode */
> mov r0, #SRAMC_SELF_FRESH_ACTIVE
> bl at91_sramc_self_refresh
> @@ -107,6 +120,14 @@ ENTRY(at91_pm_suspend_in_sram)
> tst r0, #AT91_PM_SLOW_CLOCK
> beq standby_mode
>
> + ldr r0, .ulp_mode
> + tst r0, #AT91_PM_ULP1_MODE
> + beq ulp0_mode
> +
> +ulp1_mode:
> + bl at91_pm_ulp1_mode
> + b pm_exit
> +
> ulp0_mode:
> bl at91_pm_ulp0_mode
> b pm_exit
> @@ -313,6 +334,94 @@ ENTRY(at91_pm_ulp0_mode)
> mov pc, lr
> ENDPROC(at91_pm_ulp0_mode)
>
> +/*
> + * void at91_pm_ulp1_mode(void)
> + *
> + */
> +ENTRY(at91_pm_ulp1_mode)
> + ldr pmc, .pmc_base
> +
> + /* Save PMC_MCKR config */
> + ldr tmp1, [pmc, #AT91_PMC_MCKR]
> + str tmp1, .saved_mckr
> +
> + /* Switch the master clock source to main clock */
> + bic tmp1, tmp1, #AT91_PMC_CSS
> + orr tmp1, tmp1, #AT91_PMC_CSS_MAIN
> + str tmp1, [pmc, #AT91_PMC_MCKR]
> +
> + wait_mckrdy
> +
> + /* Save PLLA config, then and disable PLLA */
> + ldr tmp1, [pmc, #AT91_CKGR_PLLAR]
> + str tmp1, .saved_pllar
> +
> + bic tmp1, tmp1, #AT91_PMC3_MUL
> + str tmp1, [pmc, #AT91_CKGR_PLLAR]
> +
> + /* Switch main clock to 12-MHz RC oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + bic tmp1, tmp1, #AT91_PMC_MOSCSEL
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_moscsels
> +
> + /* Disable the main oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + bic tmp1, tmp1, #AT91_PMC_MOSCEN
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + /* Enter the ULP1 mode by setting WAITMODE bit in CKGR_MOR */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + orr tmp1, tmp1, #AT91_PMC_WAITMODE
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_mckrdy
> +
> + /* Enable the main oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + orr tmp1, tmp1, #AT91_PMC_MOSCEN
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_moscrdy
> +
> + /* Switch main clock to the main oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + orr tmp1, tmp1, #AT91_PMC_MOSCSEL
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_moscsels
> +
> + /* Restore PLLA config */
> + ldr tmp1, .saved_pllar
> + str tmp1, [pmc, #AT91_CKGR_PLLAR]
> +
> + wait_pllalock
> +
> + /* Restore PMC_MCKR config */
> + ldr tmp1, .saved_mckr
> + str tmp1, [pmc, #AT91_PMC_MCKR]
> +
> + wait_mckrdy
> +
> + mov pc, lr
> +ENDPROC(at91_pm_ulp1_mode)
> +
> .pmc_base:
> .word 0
> .sramc_base:
> @@ -323,6 +432,8 @@ ENDPROC(at91_pm_ulp0_mode)
> .word 0
> .pm_mode:
> .word 0
> +.ulp_mode:
> + .word 0
> .saved_mckr:
> .word 0
> .saved_pllar:
> diff --git a/include/linux/clk/at91_pmc.h b/include/linux/clk/at91_pmc.h
> index 7669f76..3dc4e60 100644
> --- a/include/linux/clk/at91_pmc.h
> +++ b/include/linux/clk/at91_pmc.h
> @@ -59,8 +59,10 @@ extern void __iomem *at91_pmc_base;
> #define AT91_CKGR_MOR 0x20 /* Main Oscillator Register [not on SAM9RL] */
> #define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */
> #define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass */
> +#define AT91_PMC_WAITMODE (1 << 2) /* Wait Mode Command */
> #define AT91_PMC_MOSCRCEN (1 << 3) /* Main On-Chip RC Oscillator Enable [some SAM9] */
> #define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */
> +#define AT91_PMC_KEY_MASK (0xff << 16)
> #define AT91_PMC_KEY (0x37 << 16) /* MOR Writing Key */
> #define AT91_PMC_MOSCSEL (1 << 24) /* Main Oscillator Selection [some SAM9] */
> #define AT91_PMC_CFDEN (1 << 25) /* Clock Failure Detector Enable [some SAM9] */
> @@ -166,6 +168,38 @@ extern void __iomem *at91_pmc_base;
> #define AT91_PMC_CFDEV (1 << 18) /* Clock Failure Detector Event [some SAM9] */
> #define AT91_PMC_IMR 0x6c /* Interrupt Mask Register */
>
> +#define AT91_PMC_FSMR 0x70 /* Fast Startup Mode Register */
> +#define AT91_PMC_FSTT0 (1 << 0) /* Fast Startup from WKUP Pin Enable */
> +#define AT91_PMC_FSTT1 (1 << 1) /* Fast Startup from Security Module Enable */
> +#define AT91_PMC_FSTT2 (1 << 2) /* Fast Startup from PIOBU0 Input Enable */
> +#define AT91_PMC_FSTT3 (1 << 3) /* Fast Startup from PIOBU1 Input Enable */
> +#define AT91_PMC_FSTT4 (1 << 4) /* Fast Startup from PIOBU2 Input Enable */
> +#define AT91_PMC_FSTT5 (1 << 5) /* Fast Startup from PIOBU3 Input Enable */
> +#define AT91_PMC_FSTT6 (1 << 6) /* Fast Startup from PIOBU4 Input Enable */
> +#define AT91_PMC_FSTT7 (1 << 7) /* Fast Startup from PIOBU5 Input Enable */
> +#define AT91_PMC_FSTT8 (1 << 8) /* Fast Startup from PIOBU6 Input Enable */
> +#define AT91_PMC_FSTT9 (1 << 9) /* Fast Startup from PIOBU7 Input Enable */
> +#define AT91_PMC_FSTT10 (1 << 10) /* Fast Startup from GMAC Wake-up On LAN Enable */
> +#define AT91_PMC_RTCAL (1 << 17) /* Fast Startup from RTC Alarm Enable */
> +#define AT91_PMC_USBAL (1 << 18) /* Fast Startup from USB Resume Enable */
> +#define AT91_PMC_SDMMC_CD (1 << 19) /* Fast Startup from SDMMC Card Detect Enable */
> +#define AT91_PMC_LPM (1 << 20) /* Low-power Mode */
> +#define AT91_PMC_RXLP_MCE (1 << 24) /* Fast Startup from Backup UART Receive Match Condition Enable */
> +#define AT91_PMC_ACC_CE (1 << 25) /* Fast Startup from Analog Comparator Controller Comparison Enable*/
> +
> +#define AT91_PMC_FSPR 0x74 /* Fast Startup Polarity Register */
> +#define AT91_PMC_FSTP0 (1 << 0) /* WKUP Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP1 (1 << 1) /* Security Module Polarity for Fast Startup */
> +#define AT91_PMC_FSTP2 (1 << 2) /* PIOBU0 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP3 (1 << 3) /* PIOBU1 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP4 (1 << 4) /* PIOBU2 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP5 (1 << 5) /* PIOBU3 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP6 (1 << 6) /* PIOBU4 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP7 (1 << 7) /* PIOBU5 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP8 (1 << 8) /* PIOBU6 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP9 (1 << 9) /* PIOBU7 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP10 (1 << 10) /* GMAC Wake-up On LAN Polarity for Fast Startup */
> +
> #define AT91_PMC_PLLICPR 0x80 /* PLL Charge Pump Current Register */
>
> #define AT91_PMC_PROT 0xe4 /* Write Protect Mode Register [some SAM9] */
> @@ -177,6 +211,8 @@ extern void __iomem *at91_pmc_base;
> #define AT91_PMC_WPVS (0x1 << 0) /* Write Protect Violation Status */
> #define AT91_PMC_WPVSRC (0xffff << 8) /* Write Protect Violation Source */
>
> +#define AT91_PMC_VERSION 0xfc
> +
> #define AT91_PMC_PCER1 0x100 /* Peripheral Clock Enable Register 1 [SAMA5 only]*/
> #define AT91_PMC_PCDR1 0x104 /* Peripheral Clock Enable Register 1 */
> #define AT91_PMC_PCSR1 0x108 /* Peripheral Clock Enable Register 1 */
> --
> 1.7.9.5
>
WARNING: multiple messages have this Message-ID (diff)
From: Michael Turquette <mturquette@baylibre.com>
To: Wenyou Yang <wenyou.yang@atmel.com>,
"Nicolas Ferre" <nicolas.ferre@atmel.com>,
"Alexandre Belloni" <alexandre.belloni@free-electrons.com>,
"Jean-Christophe Plagniol-Villard" <plagnioj@jcrosoft.com>
Cc: "Russell King" <linux@arm.linux.org.uk>,
"Stephen Boyd" <sboyd@codeaurora.org>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
"Wenyou Yang" <wenyou.yang@atmel.com>
Subject: Re: [PATCH 2/2] ARM: at91/pm: add ultra Low-power mode 1(ULP1) support
Date: Thu, 15 Oct 2015 02:31:46 -0700 [thread overview]
Message-ID: <20151015093146.7777.781@quantum> (raw)
In-Reply-To: <1444880467-18598-3-git-send-email-wenyou.yang@atmel.com>
Quoting Wenyou Yang (2015-10-14 20:41:07)
> The Ultra Low-power mode 1(ULP1) is introduced by SAMA5D2.
>
> In the ULP1 mode, all the clocks are shut off, inclusive the embedded
> 12MHz RC oscillator, so as to achieve the lowest power consumption
> with the system in retention mode and able to resume on the wake up
> events. As soon as the wake up event is asserted, the embedded 12MHz
> RC oscillator restarts automatically.
>
> The number of wake up sources for the ULP1 mode is limited, the wake
> up sources should be configured via the PMC_FSMR and PMC_FSPR
> registers.
>
> In this patch, the following wake up sources are enabled,
> - WKUP0 pin
> - WKUP1 pin to WKUP8 pin (shared with PIOBU0 to PIOBU7)
> - RTC alarm
>
> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
For the changes to the clk header:
Acked-by: Michael Turquette <mturquette@baylibre.com>
> ---
>
> arch/arm/mach-at91/pm.c | 29 ++++++++++
> arch/arm/mach-at91/pm.h | 7 +++
> arch/arm/mach-at91/pm_suspend.S | 111 +++++++++++++++++++++++++++++++++++++++
> include/linux/clk/at91_pmc.h | 36 +++++++++++++
> 4 files changed, 183 insertions(+)
>
> diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
> index 80e277c..49443d9 100644
> --- a/arch/arm/mach-at91/pm.c
> +++ b/arch/arm/mach-at91/pm.c
> @@ -35,6 +35,11 @@
> #include "generic.h"
> #include "pm.h"
>
> +#define ULP0_MODE 0x00
> +#define ULP1_MODE 0x11
> +
> +#define SAMA5D2_PMC_VERSION 0x20540
> +
> /*
> * FIXME: this is needed to communicate between the pinctrl driver and
> * the PM implementation in the machine. Possibly part of the PM
> @@ -64,6 +69,23 @@ static int at91_pm_valid_state(suspend_state_t state)
> }
> }
>
> +static void at91_config_ulp1_wkup_source(void)
> +{
> + if (at91_pmc_read(AT91_PMC_VERSION) >= SAMA5D2_PMC_VERSION) {
> + at91_pmc_write(AT91_PMC_FSMR, AT91_PMC_RTCAL |
> + AT91_PMC_FSTT9 |
> + AT91_PMC_FSTT8 |
> + AT91_PMC_FSTT7 |
> + AT91_PMC_FSTT6 |
> + AT91_PMC_FSTT5 |
> + AT91_PMC_FSTT4 |
> + AT91_PMC_FSTT3 |
> + AT91_PMC_FSTT2 |
> + AT91_PMC_FSTT0);
> +
> + at91_pmc_write(AT91_PMC_FSPR, 0);
> + }
> +}
>
> static suspend_state_t target_state;
>
> @@ -73,6 +95,9 @@ static suspend_state_t target_state;
> static int at91_pm_begin(suspend_state_t state)
> {
> target_state = state;
> +
> + at91_config_ulp1_wkup_source();
> +
> return 0;
> }
>
> @@ -140,6 +165,10 @@ static void at91_pm_suspend(suspend_state_t state)
> pm_data |= (state == PM_SUSPEND_MEM) ?
> AT91_PM_MODE(AT91_PM_SLOW_CLOCK) : 0;
>
> + pm_data |= ((state == PM_SUSPEND_MEM) &&
> + (at91_pmc_read(AT91_PMC_VERSION) >= SAMA5D2_PMC_VERSION)) ?
> + AT91_PM_ULP(AT91_PM_ULP1_MODE) : 0;
> +
> flush_cache_all();
> outer_disable();
>
> diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
> index 3fcf881..2e76745 100644
> --- a/arch/arm/mach-at91/pm.h
> +++ b/arch/arm/mach-at91/pm.h
> @@ -39,4 +39,11 @@ extern void __iomem *at91_ramc_base[];
>
> #define AT91_PM_SLOW_CLOCK 0x01
>
> +#define AT91_PM_ULP_OFFSET 5
> +#define AT91_PM_ULP_MASK 0x03
> +#define AT91_PM_ULP(x) (((x) & AT91_PM_ULP_MASK) << AT91_PM_ULP_OFFSET)
> +
> +#define AT91_PM_ULP0_MODE 0x00
> +#define AT91_PM_ULP1_MODE 0x01
> +
> #endif
> diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S
> index 825347b..543c430 100644
> --- a/arch/arm/mach-at91/pm_suspend.S
> +++ b/arch/arm/mach-at91/pm_suspend.S
> @@ -41,6 +41,15 @@ tmp2 .req r5
> .endm
>
> /*
> + * Wait for main oscillator selection is done
> + */
> + .macro wait_moscsels
> +1: ldr tmp1, [pmc, #AT91_PMC_SR]
> + tst tmp1, #AT91_PMC_MOSCSELS
> + beq 1b
> + .endm
> +
> +/*
> * Wait until PLLA has locked.
> */
> .macro wait_pllalock
> @@ -99,6 +108,10 @@ ENTRY(at91_pm_suspend_in_sram)
> and r0, r0, #AT91_PM_MODE_MASK
> str r0, .pm_mode
>
> + lsr r0, r3, #AT91_PM_ULP_OFFSET
> + and r0, r0, #AT91_PM_ULP_MASK
> + str r0, .ulp_mode
> +
> /* Active the self-refresh mode */
> mov r0, #SRAMC_SELF_FRESH_ACTIVE
> bl at91_sramc_self_refresh
> @@ -107,6 +120,14 @@ ENTRY(at91_pm_suspend_in_sram)
> tst r0, #AT91_PM_SLOW_CLOCK
> beq standby_mode
>
> + ldr r0, .ulp_mode
> + tst r0, #AT91_PM_ULP1_MODE
> + beq ulp0_mode
> +
> +ulp1_mode:
> + bl at91_pm_ulp1_mode
> + b pm_exit
> +
> ulp0_mode:
> bl at91_pm_ulp0_mode
> b pm_exit
> @@ -313,6 +334,94 @@ ENTRY(at91_pm_ulp0_mode)
> mov pc, lr
> ENDPROC(at91_pm_ulp0_mode)
>
> +/*
> + * void at91_pm_ulp1_mode(void)
> + *
> + */
> +ENTRY(at91_pm_ulp1_mode)
> + ldr pmc, .pmc_base
> +
> + /* Save PMC_MCKR config */
> + ldr tmp1, [pmc, #AT91_PMC_MCKR]
> + str tmp1, .saved_mckr
> +
> + /* Switch the master clock source to main clock */
> + bic tmp1, tmp1, #AT91_PMC_CSS
> + orr tmp1, tmp1, #AT91_PMC_CSS_MAIN
> + str tmp1, [pmc, #AT91_PMC_MCKR]
> +
> + wait_mckrdy
> +
> + /* Save PLLA config, then and disable PLLA */
> + ldr tmp1, [pmc, #AT91_CKGR_PLLAR]
> + str tmp1, .saved_pllar
> +
> + bic tmp1, tmp1, #AT91_PMC3_MUL
> + str tmp1, [pmc, #AT91_CKGR_PLLAR]
> +
> + /* Switch main clock to 12-MHz RC oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + bic tmp1, tmp1, #AT91_PMC_MOSCSEL
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_moscsels
> +
> + /* Disable the main oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + bic tmp1, tmp1, #AT91_PMC_MOSCEN
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + /* Enter the ULP1 mode by setting WAITMODE bit in CKGR_MOR */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + orr tmp1, tmp1, #AT91_PMC_WAITMODE
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_mckrdy
> +
> + /* Enable the main oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + orr tmp1, tmp1, #AT91_PMC_MOSCEN
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_moscrdy
> +
> + /* Switch main clock to the main oscillator */
> + ldr tmp1, [pmc, #AT91_CKGR_MOR]
> + orr tmp1, tmp1, #AT91_PMC_MOSCSEL
> + bic tmp1, tmp1, #AT91_PMC_KEY_MASK
> + orr tmp1, tmp1, #AT91_PMC_KEY
> + bic tmp1, tmp1, #(7 << 4)
> + str tmp1, [pmc, #AT91_CKGR_MOR]
> +
> + wait_moscsels
> +
> + /* Restore PLLA config */
> + ldr tmp1, .saved_pllar
> + str tmp1, [pmc, #AT91_CKGR_PLLAR]
> +
> + wait_pllalock
> +
> + /* Restore PMC_MCKR config */
> + ldr tmp1, .saved_mckr
> + str tmp1, [pmc, #AT91_PMC_MCKR]
> +
> + wait_mckrdy
> +
> + mov pc, lr
> +ENDPROC(at91_pm_ulp1_mode)
> +
> .pmc_base:
> .word 0
> .sramc_base:
> @@ -323,6 +432,8 @@ ENDPROC(at91_pm_ulp0_mode)
> .word 0
> .pm_mode:
> .word 0
> +.ulp_mode:
> + .word 0
> .saved_mckr:
> .word 0
> .saved_pllar:
> diff --git a/include/linux/clk/at91_pmc.h b/include/linux/clk/at91_pmc.h
> index 7669f76..3dc4e60 100644
> --- a/include/linux/clk/at91_pmc.h
> +++ b/include/linux/clk/at91_pmc.h
> @@ -59,8 +59,10 @@ extern void __iomem *at91_pmc_base;
> #define AT91_CKGR_MOR 0x20 /* Main Oscillator Register [not on SAM9RL] */
> #define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */
> #define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass */
> +#define AT91_PMC_WAITMODE (1 << 2) /* Wait Mode Command */
> #define AT91_PMC_MOSCRCEN (1 << 3) /* Main On-Chip RC Oscillator Enable [some SAM9] */
> #define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */
> +#define AT91_PMC_KEY_MASK (0xff << 16)
> #define AT91_PMC_KEY (0x37 << 16) /* MOR Writing Key */
> #define AT91_PMC_MOSCSEL (1 << 24) /* Main Oscillator Selection [some SAM9] */
> #define AT91_PMC_CFDEN (1 << 25) /* Clock Failure Detector Enable [some SAM9] */
> @@ -166,6 +168,38 @@ extern void __iomem *at91_pmc_base;
> #define AT91_PMC_CFDEV (1 << 18) /* Clock Failure Detector Event [some SAM9] */
> #define AT91_PMC_IMR 0x6c /* Interrupt Mask Register */
>
> +#define AT91_PMC_FSMR 0x70 /* Fast Startup Mode Register */
> +#define AT91_PMC_FSTT0 (1 << 0) /* Fast Startup from WKUP Pin Enable */
> +#define AT91_PMC_FSTT1 (1 << 1) /* Fast Startup from Security Module Enable */
> +#define AT91_PMC_FSTT2 (1 << 2) /* Fast Startup from PIOBU0 Input Enable */
> +#define AT91_PMC_FSTT3 (1 << 3) /* Fast Startup from PIOBU1 Input Enable */
> +#define AT91_PMC_FSTT4 (1 << 4) /* Fast Startup from PIOBU2 Input Enable */
> +#define AT91_PMC_FSTT5 (1 << 5) /* Fast Startup from PIOBU3 Input Enable */
> +#define AT91_PMC_FSTT6 (1 << 6) /* Fast Startup from PIOBU4 Input Enable */
> +#define AT91_PMC_FSTT7 (1 << 7) /* Fast Startup from PIOBU5 Input Enable */
> +#define AT91_PMC_FSTT8 (1 << 8) /* Fast Startup from PIOBU6 Input Enable */
> +#define AT91_PMC_FSTT9 (1 << 9) /* Fast Startup from PIOBU7 Input Enable */
> +#define AT91_PMC_FSTT10 (1 << 10) /* Fast Startup from GMAC Wake-up On LAN Enable */
> +#define AT91_PMC_RTCAL (1 << 17) /* Fast Startup from RTC Alarm Enable */
> +#define AT91_PMC_USBAL (1 << 18) /* Fast Startup from USB Resume Enable */
> +#define AT91_PMC_SDMMC_CD (1 << 19) /* Fast Startup from SDMMC Card Detect Enable */
> +#define AT91_PMC_LPM (1 << 20) /* Low-power Mode */
> +#define AT91_PMC_RXLP_MCE (1 << 24) /* Fast Startup from Backup UART Receive Match Condition Enable */
> +#define AT91_PMC_ACC_CE (1 << 25) /* Fast Startup from Analog Comparator Controller Comparison Enable*/
> +
> +#define AT91_PMC_FSPR 0x74 /* Fast Startup Polarity Register */
> +#define AT91_PMC_FSTP0 (1 << 0) /* WKUP Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP1 (1 << 1) /* Security Module Polarity for Fast Startup */
> +#define AT91_PMC_FSTP2 (1 << 2) /* PIOBU0 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP3 (1 << 3) /* PIOBU1 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP4 (1 << 4) /* PIOBU2 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP5 (1 << 5) /* PIOBU3 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP6 (1 << 6) /* PIOBU4 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP7 (1 << 7) /* PIOBU5 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP8 (1 << 8) /* PIOBU6 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP9 (1 << 9) /* PIOBU7 Pin Polarity for Fast Startup */
> +#define AT91_PMC_FSTP10 (1 << 10) /* GMAC Wake-up On LAN Polarity for Fast Startup */
> +
> #define AT91_PMC_PLLICPR 0x80 /* PLL Charge Pump Current Register */
>
> #define AT91_PMC_PROT 0xe4 /* Write Protect Mode Register [some SAM9] */
> @@ -177,6 +211,8 @@ extern void __iomem *at91_pmc_base;
> #define AT91_PMC_WPVS (0x1 << 0) /* Write Protect Violation Status */
> #define AT91_PMC_WPVSRC (0xffff << 8) /* Write Protect Violation Source */
>
> +#define AT91_PMC_VERSION 0xfc
> +
> #define AT91_PMC_PCER1 0x100 /* Peripheral Clock Enable Register 1 [SAMA5 only]*/
> #define AT91_PMC_PCDR1 0x104 /* Peripheral Clock Enable Register 1 */
> #define AT91_PMC_PCSR1 0x108 /* Peripheral Clock Enable Register 1 */
> --
> 1.7.9.5
>
next prev parent reply other threads:[~2015-10-15 9:31 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-10-15 3:41 [PATCH 0/2] ARM: at91/pm: add ULP1 support Wenyou Yang
2015-10-15 3:41 ` Wenyou Yang
2015-10-15 3:41 ` [PATCH 1/2] ARM: at91/pm: move enter sleep code to a procedure Wenyou Yang
2015-10-15 3:41 ` Wenyou Yang
2015-10-15 3:41 ` [PATCH 2/2] ARM: at91/pm: add ultra Low-power mode 1(ULP1) support Wenyou Yang
2015-10-15 3:41 ` Wenyou Yang
2015-10-15 9:31 ` Michael Turquette [this message]
2015-10-15 9:31 ` Michael Turquette
2015-10-15 9:31 ` Michael Turquette
2015-10-15 13:22 ` Alexandre Belloni
2015-10-15 13:22 ` Alexandre Belloni
2015-10-23 1:53 ` Yang, Wenyou
2015-10-23 1:53 ` Yang, Wenyou
2015-10-23 1:53 ` Yang, Wenyou
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20151015093146.7777.781@quantum \
--to=mturquette@baylibre.com \
--cc=alexandre.belloni@free-electrons.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=nicolas.ferre@atmel.com \
--cc=plagnioj@jcrosoft.com \
--cc=sboyd@codeaurora.org \
--cc=wenyou.yang@atmel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.