[PATCH] ARM: dts: da850: Add missing pin muxing for the UARTs

[kbeldan@baylibre.com (Karl Beldan)]

On Fri, Aug 26, 2016 at 05:55:23PM +0530, Sekhar Nori wrote:
> On Wednesday 24 August 2016 02:08 PM, Karl Beldan wrote:
> > On Tue, Aug 23, 2016 at 04:46:03PM +0530, Sekhar Nori wrote:
> >> On Tuesday 23 August 2016 04:39 PM, Sekhar Nori wrote:
> >>> On Friday 05 August 2016 04:30 AM, Kevin Hilman wrote:
> >>>> Karl Beldan <kbeldan@baylibre.com> writes:
> >>>>
> >>>>> On Thu, Aug 04, 2016 at 12:20:27PM -0700, Kevin Hilman wrote:
> >>>>>> Karl Beldan <kbeldan@baylibre.com> writes:
> >>>>>>
> >>>>>>> This adds 2 pinctrl groups (rtscts, rxtx) for each of the 3 UARTs.
> >>>>>>>
> >>>>>>> Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
> >>>>>>
> >>>>>> Should da850-evm be updated to use the serial2_rxtx_pins also?
> >>>>>>
> >>>>> I could not find the EVM schematics on the net and I only have an LCDK,
> >>>>> but according to the code it should, however I can't tell whether flow
> >>>>> control pins are used.
> >>>>
> >>>> Ok, let's just leave it for now, since it's working fine.  Sekhar can
> >>>> fix that up if he can dig up the schematics.
> >>>
> >>> Looks like the flow control pins are being used for McASP also on the
> >>> EVM. So lets leave the EVM as-is.
> >>
> >> Rather, the EVM dts file should be updated to use serial2_rxtx_pins like
> >> the LCDK. Right now it seems to be relying on bootloader to serial2
> >> setup pimux correctly. I can make a patch to fix that. Or if you can do
> >> it, that will be great too.
> >>
> > 
> > Indeed ATM the EVM relies on the bootloader to setup the pin muxing.
> > 
> > I just checked the uart pins routing of the EVM, the dts:
> > - should reclaim serial2_rxtx_pins and serial2_rtscts_pins
> 
> Agree.
> 
> > - can reclaim serial1_rxtx_pins (out on Audio connector but very
> >   unlikely used for audio)
> 
> I would leave alone pins which are unused on the board. Most likely the
> SPI pins are being send to audio connector for codec control over SPI.
> 
> > - should leave serial1_rtscts_pins (out on Audio connector but used by
> >   McASP so used for audio)
> 
> Agree.
> 
> > Also I think it would be better for the serial nodes to reclaim the rxtx
> > pins in the dtsi, and override the reclaimed pins in the .dts only for
> > the nodes reclaiming flow control (some other pins could also be
> > directly reclaimed in the dtsi).
> 
> You lost me here. I guess I will benefit from a code snippet to
> illustrate the intention.
> 

Sure, instead of having: {

### board.dts:
&serialN {
	pinctrl-names = "default";
	pinctrl-0 = <&serialN_rxtx_pins>;
	status = "okay";
};
&serialN+1 {
	pinctrl-names = "default";
	pinctrl-0 = <&serialN+1_rxtx_pins>, <&serialN+1_rtscts_pins>;
	status = "okay";
};

} use ------------------ {

### plat.dtsi:
serialN: serial at xxxxx {
	compatible = "ns16550a";
	pinctrl-0 = <&serialN_rxtx_pins>;
	status = "disabled";
	[...]
};
serialN+1: serial at xxxxx {
	compatible = "ns16550a";
	pinctrl-0 = <&serialN+1_rxtx_pins>;
	status = "disabled";
	[...]
};

### board.dts:
&serialN {
	status = "okay";
};
&serialN+1 {
	pinctrl-0 = <&serialN+1_rxtx_pins>, <&serialN+1_rtscts_pins>;
	status = "okay";
};

}

> > 
> > Some other cleanups would also be in order for the da850*:
> > - use labels for non dtsi (like I did for the LCDK)
> 
> Agree. That would be better and more modern.
> 
> > - add chosen,memory nodes (I guess currently only the LCDK can
> >   dispense with ATAGS)
> 
> ok.
> 
> > - use a null range translation in the da850 dtsi for the soc node
> >   (computing the offsets is error prone and is there a point)
> 
> I do agree its easier to read if offsets directly matches addresses
> specified in the technical reference manual than doing the math with
> offsets and making sure they are correct.
> 
> That said, I am not sure null range translation is really the preferred
> approach. I would go with what DT maintainers say here.
> 
> > 
> > Sure I could fix that, along with some of the above suggestions if you
> > are ok with it.
> 
> It would be nice if you could fixup mcasp0_pins in da850-evm.dts. Surely
> it is doing more than what is needed.
> 

According to the schematics it is indeed, I could squeeze it in the series.

Rgds, 
Karl

> Regards,
> Sekhar