From: "Pali Rohár" <pali.rohar@gmail.com>
To: Pavel Machek <pavel@ucw.cz>, tony@atomide.com
Cc: Sebastian Reichel <sre@kernel.org>,
kernel list <linux-kernel@vger.kernel.org>,
linux-arm-kernel <linux-arm-kernel@lists.infradead.org>,
linux-omap@vger.kernel.org, khilman@kernel.org,
aaro.koskinen@iki.fi, ivo.g.dimitrov.75@gmail.com,
patrikbachan@gmail.com, serge@hallyn.com, abcloriens@gmail.com
Subject: Re: partial bluetooth success on n900 [was Re: bluetooth/uart timeout handling]
Date: Wed, 14 Dec 2016 13:21:29 +0100 [thread overview]
Message-ID: <201612141321.30181@pali> (raw)
In-Reply-To: <20161019092506.GA1461@amd>
[-- Attachment #1: Type: Text/Plain, Size: 9380 bytes --]
On Wednesday 19 October 2016 11:25:06 Pavel Machek wrote:
> Hi!
>
> [Ccing lists.]
>
> > Can you push the patch, which gets further than negotiation into
> > some git branch available to me? I tried to apply your patch to
> > my code, but it did not work for me.
>
> Ok, I've pushed the branch to kernel.org:
>
> git push
> git@gitolite.kernel.org:pub/scm/linux/kernel/git/pavel/linux-n900.gi
> t bt-2-v4.9:bt-2-v4.9
>
> In retrospect, I did make some changes to dts, they may be
> neccessary, too.
>
> If it still does not work, please try with my .config. I'm using
> modules here, using this script:
>
> pavel@n900:/my/modules$ cat run2
> echo removing...
> sudo killall a.out
> rmmod nokia_h4p
> #rmmod omap_serial
> #rmmod serial_core
> rmmod hci_uart.ko
> #rmmod bcm2048.ko
> echo installing...
> insmod serial_core.ko
> insmod omap-serial.ko
> insmod bcm2048.ko
> insmod hci_uart.ko
> ls -al /dev/ttyO1
> sleep 1
> stty crtscts < /dev/ttyO1
> /my/tui/ofone/a.out &
>
> For the record, dmesg says:
>
> Good luck,
> Pavel
>
> [ 30.694274] g_ether gadget: notify connect true
> [ 30.714080] g_ether gadget: notify speed 425984000
> [ 127.719146] ssi-protocol ssi-protocol: WAKELINES TEST OK
> [ 218.542694] of_get_named_gpiod_flags: can't parse 'rts-gpio'
> property of node '/ocp@68000000/serial@4806c000[0]'
> [ 218.546264] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89,
> base_baud = 3000000) is a OMAP UART1
> [ 218.574157] of_get_named_gpiod_flags: can't parse 'rts-gpio'
> property of node '/ocp@68000000/serial@49020000[0]'
> [ 218.574340] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90,
> base_baud = 3000000) is a OMAP UART2
> [ 218.650115] bcm2048: probe
> [ 218.650177] bcm2048 4806c000.serial:bluetooth: GPIO lookup for
> consumer reset
> [ 218.650177] bcm2048 4806c000.serial:bluetooth: using device tree
> for GPIO lookup
> [ 218.650360] of_get_named_gpiod_flags: parsed 'reset-gpios'
> property of node '/ocp@68000000/serial@4806c000/bluetooth[0]' -
> status (0) [ 218.650390] bcm2048 4806c000.serial:bluetooth: GPIO
> lookup for consumer host-wakeup
> [ 218.650421] bcm2048 4806c000.serial:bluetooth: using device tree
> for GPIO lookup
> [ 218.650482] of_get_named_gpiod_flags: parsed 'host-wakeup-gpios'
> property of node '/ocp@68000000/serial@4806c000/bluetooth[0]' -
> status (0)
> [ 218.650512] bcm2048 4806c000.serial:bluetooth: GPIO lookup for
> consumer bluetooth-wakeup
> [ 218.650543] bcm2048 4806c000.serial:bluetooth: using device tree
> for GPIO lookup
> [ 218.650604] of_get_named_gpiod_flags: parsed
> 'bluetooth-wakeup-gpios' property of node
> '/ocp@68000000/serial@4806c000/bluetooth[0]' - status (0)
> [ 218.650817] bcm2048 4806c000.serial:bluetooth: parent uart: ttyO1
> [ 218.650817] bcm2048 4806c000.serial:bluetooth: sysclk speed: 38400
> kHz
> [ 218.650848] bcm2048 4806c000.serial:bluetooth: probe: 0
> [ 218.774139] Bluetooth: HCI UART driver ver 2.3
> [ 218.774169] Bluetooth: HCI UART protocol H4 registered
> [ 218.774169] Bluetooth: HCI UART protocol H4+ registered
> [ 218.774169] Bluetooth: HCI UART protocol BCSP registered
> [ 218.774200] Bluetooth: HCI UART protocol LL registered
> [ 218.774200] Bluetooth: HCI UART protocol ATH3K registered
> [ 218.774200] Bluetooth: HCI UART protocol Three-wire (H5)
> registered [ 219.904876] tty ttyO1: Nokia H4+ protocol initialized
> with 4806c000.serial:bluetooth!
> [ 219.921112] tty ttyO1: Nokia H4+ protocol setup...
> [ 219.921142] h4p_reset: reset
> [ 219.921142] hci_uart_init_tty
> [ 219.983520] h4p_reset: flush
> [ 219.983551] h4p_reset: speed
> [ 219.983581] tty ttyO1: setting speed to 120000 baud
> [ 219.983673] h4p_reset: safety
> [ 219.986480] tty ttyO1: wakeup received: 0 -> 1
> [ 220.013488] tty ttyO1: wait for cts... received!
> [ 220.013519] h4p_reset: flow
> [ 220.013549] tty ttyO1: Sending negotiation...
> [ 220.013580] tty ttyO1: gpio state: reset=1 wakehost=1 wakebt=1
> [ 220.013610] enqueue: hu c304cc80 skb cd4da000
> [ 220.017425] tty ttyO1: H4P negotiation:
> [ 220.017456] tty ttyO1: baudrate = 416
> [ 220.017486] tty ttyO1: system clock = 38400
> [ 220.017486] tty ttyO1: manufacturer id = 4
> [ 220.017486] tty ttyO1: version id = 11
> [ 220.017578] tty ttyO1: setting speed to 921600 baud
> [ 220.043457] tty ttyO1: wait for cts... received!
> [ 220.043548] tty ttyO1: Negotiation successful...
> [ 220.043579] tty ttyO1: Sending alive packet...
> [ 220.043579] enqueue: hu c304cc80 skb cd4dacc0
> [ 220.043853] tty ttyO1: Received alive packet!
> [ 220.047851] tty ttyO1: FW: Skip negotion packet!
> [ 220.047882] tty ttyO1: FW: Skip alive packet!
> [ 220.052185] enqueue: hu c304cc80 skb cd4da480
> [ 220.055175] enqueue: hu c304cc80 skb cd4dae40
> [ 220.058776] enqueue: hu c304cc80 skb cd4da6c0
> [ 220.058898] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.058929] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.064605] enqueue: hu c304cc80 skb cd4daf00
> [ 220.068389] enqueue: hu c304cc80 skb cd4da0c0
> [ 220.068542] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.068542] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.071960] enqueue: hu c304cc80 skb cd4da840
> [ 220.072082] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.072082] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.075592] enqueue: hu c304cc80 skb cd4da180
> [ 220.079803] enqueue: hu c304cc80 skb cd479cc0
> [ 220.084381] enqueue: hu c304cc80 skb cd479180
> [ 220.087982] enqueue: hu c304cc80 skb cd4793c0
> [ 220.088104] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.088134] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.091522] enqueue: hu c304cc80 skb cd479e40
> [ 220.095336] enqueue: hu c304cc80 skb cd479540
> [ 220.098876] enqueue: hu c304cc80 skb cd479000
> [ 220.102386] enqueue: hu c304cc80 skb cd479600
> [ 220.102478] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.102508] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.105987] enqueue: hu c304cc80 skb cd479780
> [ 220.109527] enqueue: hu c304cc80 skb cd450cc0
> [ 220.109619] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.109649] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.113098] enqueue: hu c304cc80 skb cd484600
> [ 220.113220] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.113250] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.116760] enqueue: hu c304cc80 skb cd4a9b40
> [ 220.120300] enqueue: hu c304cc80 skb cd77c840
> [ 220.124786] enqueue: hu c304cc80 skb cd4f7900
> [ 220.128387] enqueue: hu c304cc80 skb c4fb2180
> [ 220.131896] enqueue: hu c304cc80 skb c4fb23c0
> [ 220.135498] enqueue: hu c304cc80 skb c4fb2cc0
> [ 220.139007] enqueue: hu c304cc80 skb c4fb2000
> [ 220.142486] enqueue: hu c304cc80 skb cd44fcc0
> [ 220.146118] enqueue: hu c304cc80 skb cd4b60c0
> [ 220.149627] enqueue: hu c304cc80 skb cf1986c0
> [ 220.153106] enqueue: hu c304cc80 skb cf198480
> [ 220.156738] enqueue: hu c304cc80 skb cf1980c0
> [ 220.160278] enqueue: hu c304cc80 skb cf198240
> [ 220.164733] enqueue: hu c304cc80 skb cd49f780
> [ 220.168365] enqueue: hu c304cc80 skb cd4daf00
> [ 220.171844] enqueue: hu c304cc80 skb cd4da6c0
> [ 220.175445] enqueue: hu c304cc80 skb cd4dab40
> [ 220.175567] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.175567] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.178955] enqueue: hu c304cc80 skb cd479780
> [ 220.182434] enqueue: hu c304cc80 skb cd479540
> [ 220.182525] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.182556] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.186035] enqueue: hu c304cc80 skb cd4793c0
> [ 220.188140] enqueue: hu c304cc80 skb cd479b40
> [ 220.188537] enqueue: hu c304cc80 skb cd484600
> [ 220.236480] enqueue: hu c304cc80 skb cd4a9f00
> [ 220.237701] enqueue: hu c304cc80 skb cd4f7900
> [ 220.238830] enqueue: hu c304cc80 skb c4fb23c0
> [ 220.239959] enqueue: hu c304cc80 skb c4fb2b40
> [ 220.241119] enqueue: hu c304cc80 skb c3107000
> [ 220.242187] enqueue: hu c304cc80 skb cd724240
> [ 220.243286] enqueue: hu c304cc80 skb cf198540
> [ 220.244781] enqueue: hu c304cc80 skb cf198540
> [ 220.245758] enqueue: hu c304cc80 skb cd49f780
> [ 220.246612] enqueue: hu c304cc80 skb cd4daf00
> [ 220.247436] enqueue: hu c304cc80 skb cd479540
> [ 220.248535] tty ttyO1: Sending radio packet...
> [ 220.248565] enqueue: hu c304cc80 skb cd479cc0
> [ 220.248596] tty ttyO1: Radio packet sent
> [ 220.249328] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.272949] tty ttyO1: wakeup received: 1 -> 0
> [ 221.283477] tty ttyO1: radio packet timeout!
> [ 221.283630] enqueue: hu c304cc80 skb cd4a9b40
> [ 223.363372] Bluetooth: hci0 command 0xfc18 tx timeout
> pavel@n900:~$
In log are still some failures, but ... is bluetooth working now?
I see that you applied this patch:
https://git.kernel.org/cgit/linux/kernel/git/pavel/linux-n900.git/commit/?id=051aa3fbf03ac770d8344690f5a936a7f04c6884
Looks like that pinmux is in DTS file incorrect. Can somebody verify it?
Maybe Tony?
--
Pali Rohár
pali.rohar@gmail.com
[-- Attachment #2: This is a digitally signed message part. --]
[-- Type: application/pgp-signature, Size: 198 bytes --]
WARNING: multiple messages have this Message-ID (diff)
From: pali.rohar@gmail.com (Pali Rohár)
To: linux-arm-kernel@lists.infradead.org
Subject: partial bluetooth success on n900 [was Re: bluetooth/uart timeout handling]
Date: Wed, 14 Dec 2016 13:21:29 +0100 [thread overview]
Message-ID: <201612141321.30181@pali> (raw)
In-Reply-To: <20161019092506.GA1461@amd>
On Wednesday 19 October 2016 11:25:06 Pavel Machek wrote:
> Hi!
>
> [Ccing lists.]
>
> > Can you push the patch, which gets further than negotiation into
> > some git branch available to me? I tried to apply your patch to
> > my code, but it did not work for me.
>
> Ok, I've pushed the branch to kernel.org:
>
> git push
> git at gitolite.kernel.org:pub/scm/linux/kernel/git/pavel/linux-n900.gi
> t bt-2-v4.9:bt-2-v4.9
>
> In retrospect, I did make some changes to dts, they may be
> neccessary, too.
>
> If it still does not work, please try with my .config. I'm using
> modules here, using this script:
>
> pavel at n900:/my/modules$ cat run2
> echo removing...
> sudo killall a.out
> rmmod nokia_h4p
> #rmmod omap_serial
> #rmmod serial_core
> rmmod hci_uart.ko
> #rmmod bcm2048.ko
> echo installing...
> insmod serial_core.ko
> insmod omap-serial.ko
> insmod bcm2048.ko
> insmod hci_uart.ko
> ls -al /dev/ttyO1
> sleep 1
> stty crtscts < /dev/ttyO1
> /my/tui/ofone/a.out &
>
> For the record, dmesg says:
>
> Good luck,
> Pavel
>
> [ 30.694274] g_ether gadget: notify connect true
> [ 30.714080] g_ether gadget: notify speed 425984000
> [ 127.719146] ssi-protocol ssi-protocol: WAKELINES TEST OK
> [ 218.542694] of_get_named_gpiod_flags: can't parse 'rts-gpio'
> property of node '/ocp at 68000000/serial at 4806c000[0]'
> [ 218.546264] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89,
> base_baud = 3000000) is a OMAP UART1
> [ 218.574157] of_get_named_gpiod_flags: can't parse 'rts-gpio'
> property of node '/ocp at 68000000/serial at 49020000[0]'
> [ 218.574340] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90,
> base_baud = 3000000) is a OMAP UART2
> [ 218.650115] bcm2048: probe
> [ 218.650177] bcm2048 4806c000.serial:bluetooth: GPIO lookup for
> consumer reset
> [ 218.650177] bcm2048 4806c000.serial:bluetooth: using device tree
> for GPIO lookup
> [ 218.650360] of_get_named_gpiod_flags: parsed 'reset-gpios'
> property of node '/ocp at 68000000/serial at 4806c000/bluetooth[0]' -
> status (0) [ 218.650390] bcm2048 4806c000.serial:bluetooth: GPIO
> lookup for consumer host-wakeup
> [ 218.650421] bcm2048 4806c000.serial:bluetooth: using device tree
> for GPIO lookup
> [ 218.650482] of_get_named_gpiod_flags: parsed 'host-wakeup-gpios'
> property of node '/ocp at 68000000/serial at 4806c000/bluetooth[0]' -
> status (0)
> [ 218.650512] bcm2048 4806c000.serial:bluetooth: GPIO lookup for
> consumer bluetooth-wakeup
> [ 218.650543] bcm2048 4806c000.serial:bluetooth: using device tree
> for GPIO lookup
> [ 218.650604] of_get_named_gpiod_flags: parsed
> 'bluetooth-wakeup-gpios' property of node
> '/ocp at 68000000/serial at 4806c000/bluetooth[0]' - status (0)
> [ 218.650817] bcm2048 4806c000.serial:bluetooth: parent uart: ttyO1
> [ 218.650817] bcm2048 4806c000.serial:bluetooth: sysclk speed: 38400
> kHz
> [ 218.650848] bcm2048 4806c000.serial:bluetooth: probe: 0
> [ 218.774139] Bluetooth: HCI UART driver ver 2.3
> [ 218.774169] Bluetooth: HCI UART protocol H4 registered
> [ 218.774169] Bluetooth: HCI UART protocol H4+ registered
> [ 218.774169] Bluetooth: HCI UART protocol BCSP registered
> [ 218.774200] Bluetooth: HCI UART protocol LL registered
> [ 218.774200] Bluetooth: HCI UART protocol ATH3K registered
> [ 218.774200] Bluetooth: HCI UART protocol Three-wire (H5)
> registered [ 219.904876] tty ttyO1: Nokia H4+ protocol initialized
> with 4806c000.serial:bluetooth!
> [ 219.921112] tty ttyO1: Nokia H4+ protocol setup...
> [ 219.921142] h4p_reset: reset
> [ 219.921142] hci_uart_init_tty
> [ 219.983520] h4p_reset: flush
> [ 219.983551] h4p_reset: speed
> [ 219.983581] tty ttyO1: setting speed to 120000 baud
> [ 219.983673] h4p_reset: safety
> [ 219.986480] tty ttyO1: wakeup received: 0 -> 1
> [ 220.013488] tty ttyO1: wait for cts... received!
> [ 220.013519] h4p_reset: flow
> [ 220.013549] tty ttyO1: Sending negotiation...
> [ 220.013580] tty ttyO1: gpio state: reset=1 wakehost=1 wakebt=1
> [ 220.013610] enqueue: hu c304cc80 skb cd4da000
> [ 220.017425] tty ttyO1: H4P negotiation:
> [ 220.017456] tty ttyO1: baudrate = 416
> [ 220.017486] tty ttyO1: system clock = 38400
> [ 220.017486] tty ttyO1: manufacturer id = 4
> [ 220.017486] tty ttyO1: version id = 11
> [ 220.017578] tty ttyO1: setting speed to 921600 baud
> [ 220.043457] tty ttyO1: wait for cts... received!
> [ 220.043548] tty ttyO1: Negotiation successful...
> [ 220.043579] tty ttyO1: Sending alive packet...
> [ 220.043579] enqueue: hu c304cc80 skb cd4dacc0
> [ 220.043853] tty ttyO1: Received alive packet!
> [ 220.047851] tty ttyO1: FW: Skip negotion packet!
> [ 220.047882] tty ttyO1: FW: Skip alive packet!
> [ 220.052185] enqueue: hu c304cc80 skb cd4da480
> [ 220.055175] enqueue: hu c304cc80 skb cd4dae40
> [ 220.058776] enqueue: hu c304cc80 skb cd4da6c0
> [ 220.058898] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.058929] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.064605] enqueue: hu c304cc80 skb cd4daf00
> [ 220.068389] enqueue: hu c304cc80 skb cd4da0c0
> [ 220.068542] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.068542] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.071960] enqueue: hu c304cc80 skb cd4da840
> [ 220.072082] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.072082] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.075592] enqueue: hu c304cc80 skb cd4da180
> [ 220.079803] enqueue: hu c304cc80 skb cd479cc0
> [ 220.084381] enqueue: hu c304cc80 skb cd479180
> [ 220.087982] enqueue: hu c304cc80 skb cd4793c0
> [ 220.088104] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.088134] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.091522] enqueue: hu c304cc80 skb cd479e40
> [ 220.095336] enqueue: hu c304cc80 skb cd479540
> [ 220.098876] enqueue: hu c304cc80 skb cd479000
> [ 220.102386] enqueue: hu c304cc80 skb cd479600
> [ 220.102478] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.102508] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.105987] enqueue: hu c304cc80 skb cd479780
> [ 220.109527] enqueue: hu c304cc80 skb cd450cc0
> [ 220.109619] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.109649] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.113098] enqueue: hu c304cc80 skb cd484600
> [ 220.113220] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.113250] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.116760] enqueue: hu c304cc80 skb cd4a9b40
> [ 220.120300] enqueue: hu c304cc80 skb cd77c840
> [ 220.124786] enqueue: hu c304cc80 skb cd4f7900
> [ 220.128387] enqueue: hu c304cc80 skb c4fb2180
> [ 220.131896] enqueue: hu c304cc80 skb c4fb23c0
> [ 220.135498] enqueue: hu c304cc80 skb c4fb2cc0
> [ 220.139007] enqueue: hu c304cc80 skb c4fb2000
> [ 220.142486] enqueue: hu c304cc80 skb cd44fcc0
> [ 220.146118] enqueue: hu c304cc80 skb cd4b60c0
> [ 220.149627] enqueue: hu c304cc80 skb cf1986c0
> [ 220.153106] enqueue: hu c304cc80 skb cf198480
> [ 220.156738] enqueue: hu c304cc80 skb cf1980c0
> [ 220.160278] enqueue: hu c304cc80 skb cf198240
> [ 220.164733] enqueue: hu c304cc80 skb cd49f780
> [ 220.168365] enqueue: hu c304cc80 skb cd4daf00
> [ 220.171844] enqueue: hu c304cc80 skb cd4da6c0
> [ 220.175445] enqueue: hu c304cc80 skb cd4dab40
> [ 220.175567] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.175567] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.178955] enqueue: hu c304cc80 skb cd479780
> [ 220.182434] enqueue: hu c304cc80 skb cd479540
> [ 220.182525] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.182556] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.186035] enqueue: hu c304cc80 skb cd4793c0
> [ 220.188140] enqueue: hu c304cc80 skb cd479b40
> [ 220.188537] enqueue: hu c304cc80 skb cd484600
> [ 220.236480] enqueue: hu c304cc80 skb cd4a9f00
> [ 220.237701] enqueue: hu c304cc80 skb cd4f7900
> [ 220.238830] enqueue: hu c304cc80 skb c4fb23c0
> [ 220.239959] enqueue: hu c304cc80 skb c4fb2b40
> [ 220.241119] enqueue: hu c304cc80 skb c3107000
> [ 220.242187] enqueue: hu c304cc80 skb cd724240
> [ 220.243286] enqueue: hu c304cc80 skb cf198540
> [ 220.244781] enqueue: hu c304cc80 skb cf198540
> [ 220.245758] enqueue: hu c304cc80 skb cd49f780
> [ 220.246612] enqueue: hu c304cc80 skb cd4daf00
> [ 220.247436] enqueue: hu c304cc80 skb cd479540
> [ 220.248535] tty ttyO1: Sending radio packet...
> [ 220.248565] enqueue: hu c304cc80 skb cd479cc0
> [ 220.248596] tty ttyO1: Radio packet sent
> [ 220.249328] Bluetooth: hci0: Frame reassembly failed (-84)
> [ 220.272949] tty ttyO1: wakeup received: 1 -> 0
> [ 221.283477] tty ttyO1: radio packet timeout!
> [ 221.283630] enqueue: hu c304cc80 skb cd4a9b40
> [ 223.363372] Bluetooth: hci0 command 0xfc18 tx timeout
> pavel at n900:~$
In log are still some failures, but ... is bluetooth working now?
I see that you applied this patch:
https://git.kernel.org/cgit/linux/kernel/git/pavel/linux-n900.git/commit/?id=051aa3fbf03ac770d8344690f5a936a7f04c6884
Looks like that pinmux is in DTS file incorrect. Can somebody verify it?
Maybe Tony?
--
Pali Roh?r
pali.rohar at gmail.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 198 bytes
Desc: This is a digitally signed message part.
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161214/d223c86e/attachment.sig>
next prev parent reply other threads:[~2016-12-14 12:21 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20161016002454.ul5rdqwubvkct4pf@earth>
[not found] ` <20161016090959.GA377@amd>
[not found] ` <20161016173911.arxynrja6vely3d5@earth>
[not found] ` <20161017085137.GA6628@amd>
[not found] ` <20161018224259.jrwbaal27irzjqyo@earth>
2016-10-19 9:25 ` partial bluetooth success on n900 [was Re: bluetooth/uart timeout handling] Pavel Machek
2016-10-19 9:25 ` Pavel Machek
2016-10-19 9:25 ` Pavel Machek
2016-12-14 12:21 ` Pali Rohár [this message]
2016-12-14 12:21 ` Pali Rohár
2016-12-14 12:53 ` Pavel Machek
2016-12-14 12:53 ` Pavel Machek
2016-12-14 13:31 ` Sebastian Reichel
2016-12-14 13:31 ` Sebastian Reichel
2016-12-14 13:31 ` Sebastian Reichel
2016-12-14 15:10 ` Tony Lindgren
2016-12-14 15:10 ` Tony Lindgren
2016-12-14 15:52 ` Sebastian Reichel
2016-12-14 15:52 ` Sebastian Reichel
2016-12-14 16:02 ` Tony Lindgren
2016-12-14 16:02 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201612141321.30181@pali \
--to=pali.rohar@gmail.com \
--cc=aaro.koskinen@iki.fi \
--cc=abcloriens@gmail.com \
--cc=ivo.g.dimitrov.75@gmail.com \
--cc=khilman@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=patrikbachan@gmail.com \
--cc=pavel@ucw.cz \
--cc=serge@hallyn.com \
--cc=sre@kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.