All of lore.kernel.org
 help / color / mirror / Atom feed
From: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
To: <linux-arm-kernel@lists.infradead.org>,
	<linux-gpio@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<devicetree@vger.kernel.org>
Cc: <ludovic.desroches@microchip.com>, <linus.walleij@linaro.org>,
	<nicolas.ferre@microchip.com>, <alexandre.belloni@bootlin.com>,
	<robh+dt@kernel.org>, <claudiu.beznea@microchip.com>,
	Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Subject: [PATCH] pinctrl: at91: Enable slewrate by default on SAM9X60
Date: Thu, 24 Oct 2019 20:22:34 +0300	[thread overview]
Message-ID: <20191024172234.5267-1-codrin.ciubotariu@microchip.com> (raw)

On SAM9X60, slewrate should be enabled on pins with a switching frequency
below 50Mhz. Since most of our pins do not exceed this value, we enable
slewrate by default. Pins with a switching value that exceeds 50Mhz will
have to explicitly disable slewrate.

Suggested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
---
 drivers/pinctrl/pinctrl-at91.c     | 4 ++--
 include/dt-bindings/pinctrl/at91.h | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c
index 117075b5798f..c135149e84e9 100644
--- a/drivers/pinctrl/pinctrl-at91.c
+++ b/drivers/pinctrl/pinctrl-at91.c
@@ -85,8 +85,8 @@ enum drive_strength_bit {
 					 DRIVE_STRENGTH_SHIFT)
 
 enum slewrate_bit {
-	SLEWRATE_BIT_DIS,
 	SLEWRATE_BIT_ENA,
+	SLEWRATE_BIT_DIS,
 };
 
 #define SLEWRATE_BIT_MSK(name)		(SLEWRATE_BIT_##name << SLEWRATE_SHIFT)
@@ -669,7 +669,7 @@ static void at91_mux_sam9x60_set_slewrate(void __iomem *pio, unsigned pin,
 {
 	unsigned int tmp;
 
-	if (setting < SLEWRATE_BIT_DIS || setting > SLEWRATE_BIT_ENA)
+	if (setting < SLEWRATE_BIT_ENA || setting > SLEWRATE_BIT_DIS)
 		return;
 
 	tmp = readl_relaxed(pio + SAM9X60_PIO_SLEWR);
diff --git a/include/dt-bindings/pinctrl/at91.h b/include/dt-bindings/pinctrl/at91.h
index 3831f91fb3ba..e8e117306b1b 100644
--- a/include/dt-bindings/pinctrl/at91.h
+++ b/include/dt-bindings/pinctrl/at91.h
@@ -27,8 +27,8 @@
 #define AT91_PINCTRL_DRIVE_STRENGTH_MED			(0x2 << 5)
 #define AT91_PINCTRL_DRIVE_STRENGTH_HI			(0x3 << 5)
 
-#define AT91_PINCTRL_SLEWRATE_DIS	(0x0 << 9)
-#define AT91_PINCTRL_SLEWRATE_ENA	(0x1 << 9)
+#define AT91_PINCTRL_SLEWRATE_ENA	(0x0 << 9)
+#define AT91_PINCTRL_SLEWRATE_DIS	(0x1 << 9)
 
 #define AT91_PIOA	0
 #define AT91_PIOB	1
-- 
2.20.1


WARNING: multiple messages have this Message-ID (diff)
From: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
To: <linux-arm-kernel@lists.infradead.org>,
	<linux-gpio@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<devicetree@vger.kernel.org>
Cc: alexandre.belloni@bootlin.com, linus.walleij@linaro.org,
	ludovic.desroches@microchip.com, robh+dt@kernel.org,
	Codrin Ciubotariu <codrin.ciubotariu@microchip.com>,
	claudiu.beznea@microchip.com
Subject: [PATCH] pinctrl: at91: Enable slewrate by default on SAM9X60
Date: Thu, 24 Oct 2019 20:22:34 +0300	[thread overview]
Message-ID: <20191024172234.5267-1-codrin.ciubotariu@microchip.com> (raw)

On SAM9X60, slewrate should be enabled on pins with a switching frequency
below 50Mhz. Since most of our pins do not exceed this value, we enable
slewrate by default. Pins with a switching value that exceeds 50Mhz will
have to explicitly disable slewrate.

Suggested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
---
 drivers/pinctrl/pinctrl-at91.c     | 4 ++--
 include/dt-bindings/pinctrl/at91.h | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c
index 117075b5798f..c135149e84e9 100644
--- a/drivers/pinctrl/pinctrl-at91.c
+++ b/drivers/pinctrl/pinctrl-at91.c
@@ -85,8 +85,8 @@ enum drive_strength_bit {
 					 DRIVE_STRENGTH_SHIFT)
 
 enum slewrate_bit {
-	SLEWRATE_BIT_DIS,
 	SLEWRATE_BIT_ENA,
+	SLEWRATE_BIT_DIS,
 };
 
 #define SLEWRATE_BIT_MSK(name)		(SLEWRATE_BIT_##name << SLEWRATE_SHIFT)
@@ -669,7 +669,7 @@ static void at91_mux_sam9x60_set_slewrate(void __iomem *pio, unsigned pin,
 {
 	unsigned int tmp;
 
-	if (setting < SLEWRATE_BIT_DIS || setting > SLEWRATE_BIT_ENA)
+	if (setting < SLEWRATE_BIT_ENA || setting > SLEWRATE_BIT_DIS)
 		return;
 
 	tmp = readl_relaxed(pio + SAM9X60_PIO_SLEWR);
diff --git a/include/dt-bindings/pinctrl/at91.h b/include/dt-bindings/pinctrl/at91.h
index 3831f91fb3ba..e8e117306b1b 100644
--- a/include/dt-bindings/pinctrl/at91.h
+++ b/include/dt-bindings/pinctrl/at91.h
@@ -27,8 +27,8 @@
 #define AT91_PINCTRL_DRIVE_STRENGTH_MED			(0x2 << 5)
 #define AT91_PINCTRL_DRIVE_STRENGTH_HI			(0x3 << 5)
 
-#define AT91_PINCTRL_SLEWRATE_DIS	(0x0 << 9)
-#define AT91_PINCTRL_SLEWRATE_ENA	(0x1 << 9)
+#define AT91_PINCTRL_SLEWRATE_ENA	(0x0 << 9)
+#define AT91_PINCTRL_SLEWRATE_DIS	(0x1 << 9)
 
 #define AT91_PIOA	0
 #define AT91_PIOB	1
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

             reply	other threads:[~2019-10-24 17:23 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-24 17:22 Codrin Ciubotariu [this message]
2019-10-24 17:22 ` [PATCH] pinctrl: at91: Enable slewrate by default on SAM9X60 Codrin Ciubotariu
2019-10-29 21:37 ` Rob Herring
2019-10-29 21:37   ` Rob Herring
2019-10-30  8:53   ` Ludovic Desroches
2019-10-30  8:53     ` Ludovic Desroches
2019-10-30 13:15     ` Rob Herring
2019-10-30 13:15       ` Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191024172234.5267-1-codrin.ciubotariu@microchip.com \
    --to=codrin.ciubotariu@microchip.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=claudiu.beznea@microchip.com \
    --cc=devicetree@vger.kernel.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=ludovic.desroches@microchip.com \
    --cc=nicolas.ferre@microchip.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.