* [PATCH linux dev-5.10 v2 1/4] ARM: dts: aspeed: everest: Add I2C bus 15 muxes
2021-09-15 21:47 [PATCH linux dev-5.10 v2 0/4] ARM: dts: aspeed: p10 i2c, leds, and gpios Eddie James
@ 2021-09-15 21:47 ` Eddie James
2021-09-15 21:47 ` [PATCH linux dev-5.10 v2 2/4] ARM: dts: aspeed: rainier: Add system LEDs Eddie James
` (3 subsequent siblings)
4 siblings, 0 replies; 7+ messages in thread
From: Eddie James @ 2021-09-15 21:47 UTC (permalink / raw)
To: openbmc; +Cc: eajames
Add the muxes that are attached on I2C bus 15.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
---
arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts | 158 +++++++++++++++++++
1 file changed, 158 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
index 09fd6a3c05d9..10e214f8c7bc 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
@@ -96,6 +96,18 @@ aliases {
i2c32 = &i2c14mux1chn1;
i2c33 = &i2c14mux1chn2;
i2c34 = &i2c14mux1chn3;
+ i2c35 = &i2c15mux0chn0;
+ i2c36 = &i2c15mux0chn1;
+ i2c37 = &i2c15mux0chn2;
+ i2c38 = &i2c15mux0chn3;
+ i2c39 = &i2c15mux1chn0;
+ i2c40 = &i2c15mux1chn1;
+ i2c41 = &i2c15mux1chn2;
+ i2c42 = &i2c15mux1chn3;
+ i2c43 = &i2c15mux2chn0;
+ i2c44 = &i2c15mux2chn1;
+ i2c45 = &i2c15mux2chn2;
+ i2c46 = &i2c15mux2chn3;
serial4 = &uart5;
@@ -2845,6 +2857,152 @@ eeprom@50 {
&i2c15 {
status = "okay";
+
+ i2c-switch@70 {
+ compatible = "nxp,pca9546";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c15mux0chn0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ };
+
+ i2c15mux0chn1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ };
+
+ i2c15mux0chn2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ };
+
+ i2c15mux0chn3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ };
+ };
+
+ i2c-switch@71 {
+ compatible = "nxp,pca9546";
+ reg = <0x71>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c15mux1chn0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ };
+
+ i2c15mux1chn1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ };
+
+ i2c15mux1chn2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ };
+
+ i2c15mux1chn3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ };
+ };
+
+ i2c-switch@72 {
+ compatible = "nxp,pca9546";
+ reg = <0x72>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c15mux2chn0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ };
+
+ i2c15mux2chn1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ };
+
+ i2c15mux2chn2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c15mux2chn3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
};
&ehci1 {
--
2.27.0
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH linux dev-5.10 v2 2/4] ARM: dts: aspeed: rainier: Add system LEDs
2021-09-15 21:47 [PATCH linux dev-5.10 v2 0/4] ARM: dts: aspeed: p10 i2c, leds, and gpios Eddie James
2021-09-15 21:47 ` [PATCH linux dev-5.10 v2 1/4] ARM: dts: aspeed: everest: Add I2C bus 15 muxes Eddie James
@ 2021-09-15 21:47 ` Eddie James
2021-09-15 21:47 ` [PATCH linux dev-5.10 v2 3/4] ARM: dts: aspeed: rainier: Add eeprom on bus 12 Eddie James
` (2 subsequent siblings)
4 siblings, 0 replies; 7+ messages in thread
From: Eddie James @ 2021-09-15 21:47 UTC (permalink / raw)
To: openbmc; +Cc: eajames
Add all the missing system LEDs. These are all connected by GPIO
expanders.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
---
Changes since v1:
- Add missing gpio expander at 0x60 on i2c-7
arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 1193 +++++++++++++++++-
1 file changed, 1182 insertions(+), 11 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
index 99daef25fd69..a039d91114ad 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
@@ -1098,6 +1098,62 @@ tmp275@4a {
reg = <0x4a>;
};
+ pca9551@60 {
+ compatible = "nxp,pca9551";
+ reg = <0x60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "cablecard0-cxp-top";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "cablecard0-cxp-bot";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@2 {
+ reg = <2>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@3 {
+ reg = <3>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@4 {
+ reg = <4>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@5 {
+ reg = <5>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@6 {
+ reg = <6>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@7 {
+ reg = <7>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+ };
+
pca9546@70 {
compatible = "nxp,pca9546";
reg = <0x70>;
@@ -1154,6 +1210,118 @@ tmp275@49 {
reg = <0x49>;
};
+ pca9551@60 {
+ compatible = "nxp,pca9551";
+ reg = <0x60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "cablecard3-cxp-top";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "cablecard3-cxp-bot";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@2 {
+ reg = <2>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@3 {
+ reg = <3>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@4 {
+ reg = <4>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@5 {
+ reg = <5>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@6 {
+ reg = <6>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@7 {
+ reg = <7>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+ };
+
+ pca9551@61 {
+ compatible = "nxp,pca9551";
+ reg = <0x61>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "cablecard4-cxp-top";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "cablecard4-cxp-bot";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@2 {
+ reg = <2>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@3 {
+ reg = <3>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@4 {
+ reg = <4>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@5 {
+ reg = <5>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@6 {
+ reg = <6>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@7 {
+ reg = <7>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+ };
+
pca9546@70 {
compatible = "nxp,pca9546";
reg = <0x70>;
@@ -1262,6 +1430,531 @@ &i2c7 {
multi-master;
status = "okay";
+ pca9552@30 {
+ compatible = "ibm,pca9552";
+ reg = <0x30>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "pcieslot0";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "pcieslot1";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@2 {
+ label = "pcieslot2";
+ reg = <2>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@3 {
+ label = "pcieslot3";
+ reg = <3>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@4 {
+ label = "pcieslot4";
+ reg = <4>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@5 {
+ label = "cpu1";
+ reg = <5>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@6 {
+ label = "cpu-vrm1";
+ reg = <6>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@7 {
+ reg = <7>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ led@8 {
+ label = "lcd-russel";
+ reg = <8>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@9 {
+ reg = <9>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@10 {
+ reg = <10>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@11 {
+ reg = <11>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@12 {
+ reg = <12>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@13 {
+ reg = <13>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@14 {
+ reg = <14>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@15 {
+ reg = <15>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+ };
+
+ pca9552@31 {
+ compatible = "ibm,pca9552";
+ reg = <0x31>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "ddimm0";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "ddimm1";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@2 {
+ label = "ddimm2";
+ reg = <2>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@3 {
+ label = "ddimm3";
+ reg = <3>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@4 {
+ label = "ddimm4";
+ reg = <4>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@5 {
+ label = "ddimm5";
+ reg = <5>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@6 {
+ label = "ddimm6";
+ reg = <6>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@7 {
+ label = "ddimm7";
+ reg = <7>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@8 {
+ label = "ddimm8";
+ reg = <8>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@9 {
+ label = "ddimm9";
+ reg = <9>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@10 {
+ label = "ddimm10";
+ reg = <10>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@11 {
+ label = "ddimm11";
+ reg = <11>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@12 {
+ label = "ddimm12";
+ reg = <12>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@13 {
+ label = "ddimm13";
+ reg = <13>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@14 {
+ label = "ddimm14";
+ reg = <14>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@15 {
+ label = "ddimm15";
+ reg = <15>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+ };
+
+ pca9552@32 {
+ compatible = "ibm,pca9552";
+ reg = <0x32>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "ddimm16";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "ddimm17";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@2 {
+ label = "ddimm18";
+ reg = <2>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@3 {
+ label = "ddimm19";
+ reg = <3>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@4 {
+ label = "ddimm20";
+ reg = <4>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@5 {
+ label = "ddimm21";
+ reg = <5>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@6 {
+ label = "ddimm22";
+ reg = <6>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@7 {
+ label = "ddimm23";
+ reg = <7>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@8 {
+ label = "ddimm24";
+ reg = <8>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@9 {
+ label = "ddimm25";
+ reg = <9>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@10 {
+ label = "ddimm26";
+ reg = <10>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@11 {
+ label = "ddimm27";
+ reg = <11>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@12 {
+ label = "ddimm28";
+ reg = <12>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@13 {
+ label = "ddimm29";
+ reg = <13>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@14 {
+ label = "ddimm30";
+ reg = <14>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@15 {
+ label = "ddimm31";
+ reg = <15>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+ };
+
+ pca9552@33 {
+ compatible = "ibm,pca9552";
+ reg = <0x33>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "planar";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "cpu0";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@2 {
+ reg = <2>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ led@3 {
+ label = "dasd-pyramid0";
+ reg = <3>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@4 {
+ label = "dasd-pyramid1";
+ reg = <4>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@5 {
+ label = "dasd-pyramid2";
+ reg = <5>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@6 {
+ label = "cpu0-vrm0";
+ reg = <6>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@7 {
+ label = "rtc-battery";
+ reg = <7>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@8 {
+ label = "base-blyth";
+ reg = <8>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@9 {
+ label = "pcieslot6";
+ reg = <9>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@10 {
+ label = "pcieslot7";
+ reg = <10>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@11 {
+ label = "pcieslot8";
+ reg = <11>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@12 {
+ label = "pcieslot9";
+ reg = <12>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@13 {
+ label = "pcieslot10";
+ reg = <13>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@14 {
+ label = "pcieslot11";
+ reg = <14>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@15 {
+ label = "tpm-wilson";
+ reg = <15>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+ };
+
si7021-a20@40 {
compatible = "silabs,si7020";
reg = <0x40>;
@@ -1357,33 +2050,45 @@ fan5: fan@5 {
};
};
- pca0: pca9552@61 {
- compatible = "nxp,pca9552";
- reg = <0x61>;
+ pca9551@60 {
+ compatible = "nxp,pca9551";
+ reg = <0x60>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
- gpio@0 {
+ led@0 {
+ label = "front-sys-id0";
reg = <0>;
- type = <PCA955X_TYPE_GPIO>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
};
- gpio@1 {
+ led@1 {
+ label = "front-check-log0";
reg = <1>;
- type = <PCA955X_TYPE_GPIO>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
};
- gpio@2 {
+ led@2 {
+ label = "front-enc-fault1";
reg = <2>;
- type = <PCA955X_TYPE_GPIO>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
};
- gpio@3 {
+ led@3 {
+ label = "front-sys-pwron0";
reg = <3>;
- type = <PCA955X_TYPE_GPIO>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
};
gpio@4 {
@@ -1405,6 +2110,74 @@ gpio@7 {
reg = <7>;
type = <PCA955X_TYPE_GPIO>;
};
+ };
+
+ pca0: pca9552@61 {
+ compatible = "nxp,pca9552";
+ reg = <0x61>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "fan0";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "fan1";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@2 {
+ label = "fan2";
+ reg = <2>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@3 {
+ label = "fan3";
+ reg = <3>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@4 {
+ label = "fan4";
+ reg = <4>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@5 {
+ label = "fan5";
+ reg = <5>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@6 {
+ reg = <6>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@7 {
+ reg = <7>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
gpio@8 {
reg = <8>;
@@ -1653,6 +2426,62 @@ tmp275@49 {
reg = <0x49>;
};
+ pca9551@60 {
+ compatible = "nxp,pca9551";
+ reg = <0x60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "cablecard10-cxp-top";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "cablecard10-cxp-bot";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@2 {
+ reg = <2>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@3 {
+ reg = <3>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@4 {
+ reg = <4>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@5 {
+ reg = <5>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@6 {
+ reg = <6>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@7 {
+ reg = <7>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+ };
+
pca9546@70 {
compatible = "nxp,pca9546";
reg = <0x70>;
@@ -1696,6 +2525,120 @@ eeprom@50 {
compatible = "atmel,24c64";
reg = <0x50>;
};
+
+ pca9552@60 {
+ compatible = "nxp,pca9552";
+ reg = <0x60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "nvme0";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "nvme1";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@2 {
+ label = "nvme2";
+ reg = <2>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@3 {
+ label = "nvme3";
+ reg = <3>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@4 {
+ label = "nvme4";
+ reg = <4>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@5 {
+ label = "nvme5";
+ reg = <5>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@6 {
+ label = "nvme6";
+ reg = <6>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@7 {
+ label = "nvme7";
+ reg = <7>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@8 {
+ reg = <8>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@9 {
+ reg = <9>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@10 {
+ reg = <10>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@11 {
+ reg = <11>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@12 {
+ reg = <12>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@13 {
+ reg = <13>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@14 {
+ reg = <14>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@15 {
+ reg = <15>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+ };
};
&i2c14 {
@@ -1705,6 +2648,120 @@ eeprom@50 {
compatible = "atmel,24c64";
reg = <0x50>;
};
+
+ pca9552@60 {
+ compatible = "nxp,pca9552";
+ reg = <0x60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "nvme8";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "nvme9";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@2 {
+ label = "nvme10";
+ reg = <2>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@3 {
+ label = "nvme11";
+ reg = <3>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@4 {
+ label = "nvme12";
+ reg = <4>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@5 {
+ label = "nvme13";
+ reg = <5>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@6 {
+ label = "nvme14";
+ reg = <6>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@7 {
+ label = "nvme15";
+ reg = <7>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@8 {
+ reg = <8>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@9 {
+ reg = <9>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@10 {
+ reg = <10>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@11 {
+ reg = <11>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@12 {
+ reg = <12>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@13 {
+ reg = <13>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@14 {
+ reg = <14>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@15 {
+ reg = <15>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+ };
};
&i2c15 {
@@ -1714,6 +2771,120 @@ eeprom@50 {
compatible = "atmel,24c64";
reg = <0x50>;
};
+
+ pca9552@60 {
+ compatible = "nxp,pca9552";
+ reg = <0x60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ led@0 {
+ label = "nvme16";
+ reg = <0>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@1 {
+ label = "nvme17";
+ reg = <1>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@2 {
+ label = "nvme18";
+ reg = <2>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@3 {
+ label = "nvme19";
+ reg = <3>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@4 {
+ label = "nvme20";
+ reg = <4>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@5 {
+ label = "nvme21";
+ reg = <5>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@6 {
+ label = "nvme22";
+ reg = <6>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ led@7 {
+ label = "nvme23";
+ reg = <7>;
+ retain-state-shutdown;
+ default-state = "keep";
+ type = <PCA955X_TYPE_LED>;
+ };
+
+ gpio@8 {
+ reg = <8>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@9 {
+ reg = <9>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@10 {
+ reg = <10>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@11 {
+ reg = <11>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@12 {
+ reg = <12>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@13 {
+ reg = <13>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@14 {
+ reg = <14>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+
+ gpio@15 {
+ reg = <15>;
+ type = <PCA955X_TYPE_GPIO>;
+ };
+ };
};
&vuart1 {
--
2.27.0
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH linux dev-5.10 v2 3/4] ARM: dts: aspeed: rainier: Add eeprom on bus 12
2021-09-15 21:47 [PATCH linux dev-5.10 v2 0/4] ARM: dts: aspeed: p10 i2c, leds, and gpios Eddie James
2021-09-15 21:47 ` [PATCH linux dev-5.10 v2 1/4] ARM: dts: aspeed: everest: Add I2C bus 15 muxes Eddie James
2021-09-15 21:47 ` [PATCH linux dev-5.10 v2 2/4] ARM: dts: aspeed: rainier: Add system LEDs Eddie James
@ 2021-09-15 21:47 ` Eddie James
2021-09-15 21:47 ` [PATCH linux dev-5.10 v2 4/4] ARM: dts: aspeed: Rainier: Remove gpio hog for GPIOP7 Eddie James
2021-09-16 7:20 ` [PATCH linux dev-5.10 v2 0/4] ARM: dts: aspeed: p10 i2c, leds, and gpios Joel Stanley
4 siblings, 0 replies; 7+ messages in thread
From: Eddie James @ 2021-09-15 21:47 UTC (permalink / raw)
To: openbmc; +Cc: eajames
The devicetree was missing an eeprom.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
index a039d91114ad..2b6bb20dfd82 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
@@ -2516,6 +2516,11 @@ eeprom@51 {
&i2c12 {
status = "okay";
+
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
};
&i2c13 {
--
2.27.0
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH linux dev-5.10 v2 4/4] ARM: dts: aspeed: Rainier: Remove gpio hog for GPIOP7
2021-09-15 21:47 [PATCH linux dev-5.10 v2 0/4] ARM: dts: aspeed: p10 i2c, leds, and gpios Eddie James
` (2 preceding siblings ...)
2021-09-15 21:47 ` [PATCH linux dev-5.10 v2 3/4] ARM: dts: aspeed: rainier: Add eeprom on bus 12 Eddie James
@ 2021-09-15 21:47 ` Eddie James
2021-09-16 7:20 ` Joel Stanley
2021-09-16 7:20 ` [PATCH linux dev-5.10 v2 0/4] ARM: dts: aspeed: p10 i2c, leds, and gpios Joel Stanley
4 siblings, 1 reply; 7+ messages in thread
From: Eddie James @ 2021-09-15 21:47 UTC (permalink / raw)
To: openbmc; +Cc: eajames
Only the pass 1 Ingraham board (Rainier system) had a micro-controller
wired to GPIOP7 on ball Y23. Pass 2 boards have this ball wired to the
heartbeat LED, so remove the hog and add it to the pass 1 devicetrees.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u-p1.dts | 9 +++++++++
arch/arm/boot/dts/aspeed-bmc-ibm-rainier-p1.dts | 9 +++++++++
arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 7 -------
3 files changed, 18 insertions(+), 7 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u-p1.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u-p1.dts
index e35a3efd9d22..b7ec83848750 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u-p1.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u-p1.dts
@@ -22,6 +22,15 @@ aliases {
};
};
+&gpio0 {
+ pin_mclr_vpp {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(P, 7) GPIO_OPEN_DRAIN>;
+ output-high;
+ line-name = "mclr_vpp";
+ };
+};
+
&i2c4 {
/delete-node/ pca9546@70;
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-p1.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-p1.dts
index b3c923f1838b..d650dbebe5d2 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-p1.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-p1.dts
@@ -22,6 +22,15 @@ aliases {
};
};
+&gpio0 {
+ pin_mclr_vpp {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(P, 7) GPIO_OPEN_DRAIN>;
+ output-high;
+ line-name = "mclr_vpp";
+ };
+};
+
&i2c4 {
/delete-node/ pca9546@70;
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
index 2b6bb20dfd82..9250d9465407 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
@@ -254,13 +254,6 @@ &gpio0 {
/*Y0-Y7*/ "","","","","","","","",
/*Z0-Z7*/ "","","","","","","","";
- pin_mclr_vpp {
- gpio-hog;
- gpios = <ASPEED_GPIO(P, 7) GPIO_OPEN_DRAIN>;
- output-high;
- line-name = "mclr_vpp";
- };
-
i2c3_mux_oe_n {
gpio-hog;
gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
--
2.27.0
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH linux dev-5.10 v2 4/4] ARM: dts: aspeed: Rainier: Remove gpio hog for GPIOP7
2021-09-15 21:47 ` [PATCH linux dev-5.10 v2 4/4] ARM: dts: aspeed: Rainier: Remove gpio hog for GPIOP7 Eddie James
@ 2021-09-16 7:20 ` Joel Stanley
0 siblings, 0 replies; 7+ messages in thread
From: Joel Stanley @ 2021-09-16 7:20 UTC (permalink / raw)
To: Eddie James; +Cc: OpenBMC Maillist
On Wed, 15 Sept 2021 at 21:47, Eddie James <eajames@linux.ibm.com> wrote:
>
> Only the pass 1 Ingraham board (Rainier system) had a micro-controller
> wired to GPIOP7 on ball Y23. Pass 2 boards have this ball wired to the
> heartbeat LED, so remove the hog and add it to the pass 1 devicetrees.
We can obviously remove it from the device tree we have, which is for
the pass2, but we can't add it to pass1 as we don't have them in the
tree.
I recommend submitting them to the openbmc tree (but not mainline, as
they're pass1), and we can maintain them in there.
Cheers,
Joel
>
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
> arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u-p1.dts | 9 +++++++++
> arch/arm/boot/dts/aspeed-bmc-ibm-rainier-p1.dts | 9 +++++++++
> arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 7 -------
> 3 files changed, 18 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u-p1.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u-p1.dts
> index e35a3efd9d22..b7ec83848750 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u-p1.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u-p1.dts
> @@ -22,6 +22,15 @@ aliases {
> };
> };
>
> +&gpio0 {
> + pin_mclr_vpp {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(P, 7) GPIO_OPEN_DRAIN>;
> + output-high;
> + line-name = "mclr_vpp";
> + };
> +};
> +
> &i2c4 {
> /delete-node/ pca9546@70;
>
> diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-p1.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-p1.dts
> index b3c923f1838b..d650dbebe5d2 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-p1.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-p1.dts
> @@ -22,6 +22,15 @@ aliases {
> };
> };
>
> +&gpio0 {
> + pin_mclr_vpp {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(P, 7) GPIO_OPEN_DRAIN>;
> + output-high;
> + line-name = "mclr_vpp";
> + };
> +};
> +
> &i2c4 {
> /delete-node/ pca9546@70;
>
> diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
> index 2b6bb20dfd82..9250d9465407 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
> @@ -254,13 +254,6 @@ &gpio0 {
> /*Y0-Y7*/ "","","","","","","","",
> /*Z0-Z7*/ "","","","","","","","";
>
> - pin_mclr_vpp {
> - gpio-hog;
> - gpios = <ASPEED_GPIO(P, 7) GPIO_OPEN_DRAIN>;
> - output-high;
> - line-name = "mclr_vpp";
> - };
> -
> i2c3_mux_oe_n {
> gpio-hog;
> gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
> --
> 2.27.0
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH linux dev-5.10 v2 0/4] ARM: dts: aspeed: p10 i2c, leds, and gpios
2021-09-15 21:47 [PATCH linux dev-5.10 v2 0/4] ARM: dts: aspeed: p10 i2c, leds, and gpios Eddie James
` (3 preceding siblings ...)
2021-09-15 21:47 ` [PATCH linux dev-5.10 v2 4/4] ARM: dts: aspeed: Rainier: Remove gpio hog for GPIOP7 Eddie James
@ 2021-09-16 7:20 ` Joel Stanley
4 siblings, 0 replies; 7+ messages in thread
From: Joel Stanley @ 2021-09-16 7:20 UTC (permalink / raw)
To: Eddie James; +Cc: OpenBMC Maillist
On Wed, 15 Sept 2021 at 21:47, Eddie James <eajames@linux.ibm.com> wrote:
>
> Here are various additions and fixes to the P10 BMC system device trees.
>
> Changes since v1:
> - The eeprom and gpio patches
> - Add missing gpio expander at 0x60 on i2c-7
>
> Eddie James (4):
> ARM: dts: aspeed: everest: Add I2C bus 15 muxes
> ARM: dts: aspeed: rainier: Add system LEDs
> ARM: dts: aspeed: rainier: Add eeprom on bus 12
> ARM: dts: aspeed: Rainier: Remove gpio hog for GPIOP7
I've applied the first three, but only part of patch four as discussed
in that patch.
Cheers,
Joel
^ permalink raw reply [flat|nested] 7+ messages in thread