From: Ard Biesheuvel <ardb@kernel.org>
To: linux@armlinux.org.uk, linux-arm-kernel@lists.infradead.org
Cc: linux-hardening@vger.kernel.org, Ard Biesheuvel <ardb@kernel.org>,
Nicolas Pitre <nico@fluxnic.net>, Arnd Bergmann <arnd@arndb.de>,
Kees Cook <keescook@chromium.org>,
Keith Packard <keithpac@amazon.com>,
Linus Walleij <linus.walleij@linaro.org>,
Nick Desaulniers <ndesaulniers@google.com>,
Tony Lindgren <tony@atomide.com>, Marc Zyngier <maz@kernel.org>,
Vladimir Murzin <vladimir.murzin@arm.com>,
Jesse Taube <mr.bossman075@gmail.com>
Subject: [PATCH v5 13/32] ARM: percpu: add SMP_ON_UP support
Date: Mon, 24 Jan 2022 18:47:25 +0100 [thread overview]
Message-ID: <20220124174744.1054712-14-ardb@kernel.org> (raw)
In-Reply-To: <20220124174744.1054712-1-ardb@kernel.org>
Permit the use of the TPIDRPRW system register for carrying the per-CPU
offset in generic SMP configurations that also target non-SMP capable
ARMv6 cores. This uses the SMP_ON_UP code patching framework to turn all
TPIDRPRW accesses into reads/writes of entry #0 in the __per_cpu_offset
array.
While at it, switch over some existing direct TPIDRPRW accesses in asm
code to invocations of a new helper that is patched in the same way when
necessary.
Note that CPU_V6+SMP without SMP_ON_UP results in a kernel that does not
boot on v6 CPUs without SMP extensions, so add this dependency to
Kconfig as well.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
---
arch/arm/include/asm/assembler.h | 61 +++++++++++++++++++-
arch/arm/include/asm/insn.h | 17 ++++++
arch/arm/include/asm/percpu.h | 36 ++++++++++--
arch/arm/mm/Kconfig | 1 +
4 files changed, 108 insertions(+), 7 deletions(-)
diff --git a/arch/arm/include/asm/assembler.h b/arch/arm/include/asm/assembler.h
index 7a4e292b68e4..30752c4427d4 100644
--- a/arch/arm/include/asm/assembler.h
+++ b/arch/arm/include/asm/assembler.h
@@ -216,9 +216,7 @@
.macro reload_current, t1:req, t2:req
#ifdef CONFIG_CURRENT_POINTER_IN_TPIDRURO
- adr_l \t1, __entry_task @ get __entry_task base address
- mrc p15, 0, \t2, c13, c0, 4 @ get per-CPU offset
- ldr \t1, [\t1, \t2] @ load variable
+ ldr_this_cpu \t1, __entry_task, \t1, \t2
mcr p15, 0, \t1, c13, c0, 3 @ store in TPIDRURO
#endif
.endm
@@ -308,6 +306,26 @@
#define ALT_UP_B(label) b label
#endif
+ /*
+ * this_cpu_offset - load the per-CPU offset of this CPU into
+ * register 'rd'
+ */
+ .macro this_cpu_offset, rd:req
+#ifdef CONFIG_SMP
+ALT_SMP(mrc p15, 0, \rd, c13, c0, 4)
+#ifdef CONFIG_CPU_V6
+ALT_UP_B(.L0_\@)
+ .subsection 1
+.L0_\@: ldr_va \rd, __per_cpu_offset
+ b .L1_\@
+ .previous
+.L1_\@:
+#endif
+#else
+ mov \rd, #0
+#endif
+ .endm
+
/*
* Instruction barrier
*/
@@ -647,6 +665,43 @@ THUMB( orr \reg , \reg , #PSR_T_BIT )
__ldst_va str, \rn, \tmp, \sym
.endm
+ /*
+ * ldr_this_cpu_armv6 - Load a 32-bit word from the per-CPU variable 'sym',
+ * without using a temp register. Supported in ARM mode
+ * only.
+ */
+ .macro ldr_this_cpu_armv6, rd:req, sym:req
+ this_cpu_offset \rd
+ .globl \sym
+ .reloc .L0_\@, R_ARM_ALU_PC_G0_NC, \sym
+ .reloc .L1_\@, R_ARM_ALU_PC_G1_NC, \sym
+ .reloc .L2_\@, R_ARM_LDR_PC_G2, \sym
+ add \rd, \rd, pc
+.L0_\@: sub \rd, \rd, #4
+.L1_\@: sub \rd, \rd, #0
+.L2_\@: ldr \rd, [\rd, #4]
+ .endm
+
+ /*
+ * ldr_this_cpu - Load a 32-bit word from the per-CPU variable 'sym'
+ * into register 'rd', which may be the stack pointer,
+ * using 't1' and 't2' as general temp registers. These
+ * are permitted to overlap with 'rd' if != sp
+ */
+ .macro ldr_this_cpu, rd:req, sym:req, t1:req, t2:req
+#ifndef CONFIG_SMP
+ ldr_va \rd, \sym,, \t1 @ CPU offset == 0x0
+#elif __LINUX_ARM_ARCH__ >= 7 || \
+ !defined(CONFIG_ARM_HAS_GROUP_RELOCS) || \
+ (defined(MODULE) && defined(CONFIG_ARM_MODULE_PLTS))
+ this_cpu_offset \t1
+ mov_l \t2, \sym
+ ldr \rd, [\t1, \t2]
+#else
+ ldr_this_cpu_armv6 \rd, \sym
+#endif
+ .endm
+
/*
* rev_l - byte-swap a 32-bit value
*
diff --git a/arch/arm/include/asm/insn.h b/arch/arm/include/asm/insn.h
index 5475cbf9fb6b..faf3d1c28368 100644
--- a/arch/arm/include/asm/insn.h
+++ b/arch/arm/include/asm/insn.h
@@ -2,6 +2,23 @@
#ifndef __ASM_ARM_INSN_H
#define __ASM_ARM_INSN_H
+#include <linux/types.h>
+
+/*
+ * Avoid a literal load by emitting a sequence of ADD/LDR instructions with the
+ * appropriate relocations. The combined sequence has a range of -/+ 256 MiB,
+ * which should be sufficient for the core kernel as well as modules loaded
+ * into the module region. (Not supported by LLD before release 14)
+ */
+#define LOAD_SYM_ARMV6(reg, sym) \
+ " .globl " #sym " \n\t" \
+ " .reloc 10f, R_ARM_ALU_PC_G0_NC, " #sym " \n\t" \
+ " .reloc 11f, R_ARM_ALU_PC_G1_NC, " #sym " \n\t" \
+ " .reloc 12f, R_ARM_LDR_PC_G2, " #sym " \n\t" \
+ "10: sub " #reg ", pc, #8 \n\t" \
+ "11: sub " #reg ", " #reg ", #4 \n\t" \
+ "12: ldr " #reg ", [" #reg ", #0] \n\t"
+
static inline unsigned long
arm_gen_nop(void)
{
diff --git a/arch/arm/include/asm/percpu.h b/arch/arm/include/asm/percpu.h
index e2fcb3cfd3de..7feba9d65e85 100644
--- a/arch/arm/include/asm/percpu.h
+++ b/arch/arm/include/asm/percpu.h
@@ -5,20 +5,27 @@
#ifndef _ASM_ARM_PERCPU_H_
#define _ASM_ARM_PERCPU_H_
+#include <asm/insn.h>
+
register unsigned long current_stack_pointer asm ("sp");
/*
* Same as asm-generic/percpu.h, except that we store the per cpu offset
* in the TPIDRPRW. TPIDRPRW only exists on V6K and V7
*/
-#if defined(CONFIG_SMP) && !defined(CONFIG_CPU_V6)
+#ifdef CONFIG_SMP
static inline void set_my_cpu_offset(unsigned long off)
{
+ extern unsigned int smp_on_up;
+
+ if (IS_ENABLED(CONFIG_CPU_V6) && !smp_on_up)
+ return;
+
/* Set TPIDRPRW */
asm volatile("mcr p15, 0, %0, c13, c0, 4" : : "r" (off) : "memory");
}
-static inline unsigned long __my_cpu_offset(void)
+static __always_inline unsigned long __my_cpu_offset(void)
{
unsigned long off;
@@ -27,8 +34,29 @@ static inline unsigned long __my_cpu_offset(void)
* We want to allow caching the value, so avoid using volatile and
* instead use a fake stack read to hazard against barrier().
*/
- asm("mrc p15, 0, %0, c13, c0, 4" : "=r" (off)
- : "Q" (*(const unsigned long *)current_stack_pointer));
+ asm("0: mrc p15, 0, %0, c13, c0, 4 \n\t"
+#ifdef CONFIG_CPU_V6
+ "1: \n\t"
+ " .subsection 1 \n\t"
+#if defined(CONFIG_ARM_HAS_GROUP_RELOCS) && \
+ !(defined(MODULE) && defined(CONFIG_ARM_MODULE_PLTS))
+ "2: " LOAD_SYM_ARMV6(%0, __per_cpu_offset) " \n\t"
+ " b 1b \n\t"
+#else
+ "2: ldr %0, 3f \n\t"
+ " ldr %0, [%0] \n\t"
+ " b 1b \n\t"
+ "3: .long __per_cpu_offset \n\t"
+#endif
+ " .previous \n\t"
+ " .pushsection \".alt.smp.init\", \"a\" \n\t"
+ " .align 2 \n\t"
+ " .long 0b - . \n\t"
+ " b . + (2b - 0b) \n\t"
+ " .popsection \n\t"
+#endif
+ : "=r" (off)
+ : "Q" (*(const unsigned long *)current_stack_pointer));
return off;
}
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index 58afba346729..a91ff22c6c2e 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -386,6 +386,7 @@ config CPU_V6
select CPU_PABRT_V6
select CPU_THUMB_CAPABLE
select CPU_TLB_V6 if MMU
+ select SMP_ON_UP if SMP
# ARMv6k
config CPU_V6K
--
2.30.2
WARNING: multiple messages have this Message-ID (diff)
From: Ard Biesheuvel <ardb@kernel.org>
To: linux@armlinux.org.uk, linux-arm-kernel@lists.infradead.org
Cc: linux-hardening@vger.kernel.org, Ard Biesheuvel <ardb@kernel.org>,
Nicolas Pitre <nico@fluxnic.net>, Arnd Bergmann <arnd@arndb.de>,
Kees Cook <keescook@chromium.org>,
Keith Packard <keithpac@amazon.com>,
Linus Walleij <linus.walleij@linaro.org>,
Nick Desaulniers <ndesaulniers@google.com>,
Tony Lindgren <tony@atomide.com>, Marc Zyngier <maz@kernel.org>,
Vladimir Murzin <vladimir.murzin@arm.com>,
Jesse Taube <mr.bossman075@gmail.com>
Subject: [PATCH v5 13/32] ARM: percpu: add SMP_ON_UP support
Date: Mon, 24 Jan 2022 18:47:25 +0100 [thread overview]
Message-ID: <20220124174744.1054712-14-ardb@kernel.org> (raw)
In-Reply-To: <20220124174744.1054712-1-ardb@kernel.org>
Permit the use of the TPIDRPRW system register for carrying the per-CPU
offset in generic SMP configurations that also target non-SMP capable
ARMv6 cores. This uses the SMP_ON_UP code patching framework to turn all
TPIDRPRW accesses into reads/writes of entry #0 in the __per_cpu_offset
array.
While at it, switch over some existing direct TPIDRPRW accesses in asm
code to invocations of a new helper that is patched in the same way when
necessary.
Note that CPU_V6+SMP without SMP_ON_UP results in a kernel that does not
boot on v6 CPUs without SMP extensions, so add this dependency to
Kconfig as well.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
---
arch/arm/include/asm/assembler.h | 61 +++++++++++++++++++-
arch/arm/include/asm/insn.h | 17 ++++++
arch/arm/include/asm/percpu.h | 36 ++++++++++--
arch/arm/mm/Kconfig | 1 +
4 files changed, 108 insertions(+), 7 deletions(-)
diff --git a/arch/arm/include/asm/assembler.h b/arch/arm/include/asm/assembler.h
index 7a4e292b68e4..30752c4427d4 100644
--- a/arch/arm/include/asm/assembler.h
+++ b/arch/arm/include/asm/assembler.h
@@ -216,9 +216,7 @@
.macro reload_current, t1:req, t2:req
#ifdef CONFIG_CURRENT_POINTER_IN_TPIDRURO
- adr_l \t1, __entry_task @ get __entry_task base address
- mrc p15, 0, \t2, c13, c0, 4 @ get per-CPU offset
- ldr \t1, [\t1, \t2] @ load variable
+ ldr_this_cpu \t1, __entry_task, \t1, \t2
mcr p15, 0, \t1, c13, c0, 3 @ store in TPIDRURO
#endif
.endm
@@ -308,6 +306,26 @@
#define ALT_UP_B(label) b label
#endif
+ /*
+ * this_cpu_offset - load the per-CPU offset of this CPU into
+ * register 'rd'
+ */
+ .macro this_cpu_offset, rd:req
+#ifdef CONFIG_SMP
+ALT_SMP(mrc p15, 0, \rd, c13, c0, 4)
+#ifdef CONFIG_CPU_V6
+ALT_UP_B(.L0_\@)
+ .subsection 1
+.L0_\@: ldr_va \rd, __per_cpu_offset
+ b .L1_\@
+ .previous
+.L1_\@:
+#endif
+#else
+ mov \rd, #0
+#endif
+ .endm
+
/*
* Instruction barrier
*/
@@ -647,6 +665,43 @@ THUMB( orr \reg , \reg , #PSR_T_BIT )
__ldst_va str, \rn, \tmp, \sym
.endm
+ /*
+ * ldr_this_cpu_armv6 - Load a 32-bit word from the per-CPU variable 'sym',
+ * without using a temp register. Supported in ARM mode
+ * only.
+ */
+ .macro ldr_this_cpu_armv6, rd:req, sym:req
+ this_cpu_offset \rd
+ .globl \sym
+ .reloc .L0_\@, R_ARM_ALU_PC_G0_NC, \sym
+ .reloc .L1_\@, R_ARM_ALU_PC_G1_NC, \sym
+ .reloc .L2_\@, R_ARM_LDR_PC_G2, \sym
+ add \rd, \rd, pc
+.L0_\@: sub \rd, \rd, #4
+.L1_\@: sub \rd, \rd, #0
+.L2_\@: ldr \rd, [\rd, #4]
+ .endm
+
+ /*
+ * ldr_this_cpu - Load a 32-bit word from the per-CPU variable 'sym'
+ * into register 'rd', which may be the stack pointer,
+ * using 't1' and 't2' as general temp registers. These
+ * are permitted to overlap with 'rd' if != sp
+ */
+ .macro ldr_this_cpu, rd:req, sym:req, t1:req, t2:req
+#ifndef CONFIG_SMP
+ ldr_va \rd, \sym,, \t1 @ CPU offset == 0x0
+#elif __LINUX_ARM_ARCH__ >= 7 || \
+ !defined(CONFIG_ARM_HAS_GROUP_RELOCS) || \
+ (defined(MODULE) && defined(CONFIG_ARM_MODULE_PLTS))
+ this_cpu_offset \t1
+ mov_l \t2, \sym
+ ldr \rd, [\t1, \t2]
+#else
+ ldr_this_cpu_armv6 \rd, \sym
+#endif
+ .endm
+
/*
* rev_l - byte-swap a 32-bit value
*
diff --git a/arch/arm/include/asm/insn.h b/arch/arm/include/asm/insn.h
index 5475cbf9fb6b..faf3d1c28368 100644
--- a/arch/arm/include/asm/insn.h
+++ b/arch/arm/include/asm/insn.h
@@ -2,6 +2,23 @@
#ifndef __ASM_ARM_INSN_H
#define __ASM_ARM_INSN_H
+#include <linux/types.h>
+
+/*
+ * Avoid a literal load by emitting a sequence of ADD/LDR instructions with the
+ * appropriate relocations. The combined sequence has a range of -/+ 256 MiB,
+ * which should be sufficient for the core kernel as well as modules loaded
+ * into the module region. (Not supported by LLD before release 14)
+ */
+#define LOAD_SYM_ARMV6(reg, sym) \
+ " .globl " #sym " \n\t" \
+ " .reloc 10f, R_ARM_ALU_PC_G0_NC, " #sym " \n\t" \
+ " .reloc 11f, R_ARM_ALU_PC_G1_NC, " #sym " \n\t" \
+ " .reloc 12f, R_ARM_LDR_PC_G2, " #sym " \n\t" \
+ "10: sub " #reg ", pc, #8 \n\t" \
+ "11: sub " #reg ", " #reg ", #4 \n\t" \
+ "12: ldr " #reg ", [" #reg ", #0] \n\t"
+
static inline unsigned long
arm_gen_nop(void)
{
diff --git a/arch/arm/include/asm/percpu.h b/arch/arm/include/asm/percpu.h
index e2fcb3cfd3de..7feba9d65e85 100644
--- a/arch/arm/include/asm/percpu.h
+++ b/arch/arm/include/asm/percpu.h
@@ -5,20 +5,27 @@
#ifndef _ASM_ARM_PERCPU_H_
#define _ASM_ARM_PERCPU_H_
+#include <asm/insn.h>
+
register unsigned long current_stack_pointer asm ("sp");
/*
* Same as asm-generic/percpu.h, except that we store the per cpu offset
* in the TPIDRPRW. TPIDRPRW only exists on V6K and V7
*/
-#if defined(CONFIG_SMP) && !defined(CONFIG_CPU_V6)
+#ifdef CONFIG_SMP
static inline void set_my_cpu_offset(unsigned long off)
{
+ extern unsigned int smp_on_up;
+
+ if (IS_ENABLED(CONFIG_CPU_V6) && !smp_on_up)
+ return;
+
/* Set TPIDRPRW */
asm volatile("mcr p15, 0, %0, c13, c0, 4" : : "r" (off) : "memory");
}
-static inline unsigned long __my_cpu_offset(void)
+static __always_inline unsigned long __my_cpu_offset(void)
{
unsigned long off;
@@ -27,8 +34,29 @@ static inline unsigned long __my_cpu_offset(void)
* We want to allow caching the value, so avoid using volatile and
* instead use a fake stack read to hazard against barrier().
*/
- asm("mrc p15, 0, %0, c13, c0, 4" : "=r" (off)
- : "Q" (*(const unsigned long *)current_stack_pointer));
+ asm("0: mrc p15, 0, %0, c13, c0, 4 \n\t"
+#ifdef CONFIG_CPU_V6
+ "1: \n\t"
+ " .subsection 1 \n\t"
+#if defined(CONFIG_ARM_HAS_GROUP_RELOCS) && \
+ !(defined(MODULE) && defined(CONFIG_ARM_MODULE_PLTS))
+ "2: " LOAD_SYM_ARMV6(%0, __per_cpu_offset) " \n\t"
+ " b 1b \n\t"
+#else
+ "2: ldr %0, 3f \n\t"
+ " ldr %0, [%0] \n\t"
+ " b 1b \n\t"
+ "3: .long __per_cpu_offset \n\t"
+#endif
+ " .previous \n\t"
+ " .pushsection \".alt.smp.init\", \"a\" \n\t"
+ " .align 2 \n\t"
+ " .long 0b - . \n\t"
+ " b . + (2b - 0b) \n\t"
+ " .popsection \n\t"
+#endif
+ : "=r" (off)
+ : "Q" (*(const unsigned long *)current_stack_pointer));
return off;
}
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index 58afba346729..a91ff22c6c2e 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -386,6 +386,7 @@ config CPU_V6
select CPU_PABRT_V6
select CPU_THUMB_CAPABLE
select CPU_TLB_V6 if MMU
+ select SMP_ON_UP if SMP
# ARMv6k
config CPU_V6K
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-01-24 17:48 UTC|newest]
Thread overview: 76+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-01-24 17:47 [PATCH v5 00/32] ARM vmap'ed and IRQ stacks roundup Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 01/32] ARM: riscpc: drop support for IOMD_IRQREQC/IOMD_IRQREQD IRQ groups Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 02/32] ARM: riscpc: use GENERIC_IRQ_MULTI_HANDLER Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 03/32] ARM: footbridge: " Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 04/32] ARM: iop32x: offset IRQ numbers by 1 Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 05/32] ARM: iop32x: use GENERIC_IRQ_MULTI_HANDLER Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 06/32] ARM: remove old-style irq entry Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 07/32] irqchip: nvic: Use GENERIC_IRQ_MULTI_HANDLER Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 08/32] ARM: decompressor: disable stack protector Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 09/32] ARM: stackprotector: prefer compiler for TLS based per-task protector Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 10/32] ARM: entry: preserve thread_info pointer in switch_to Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 11/32] ARM: module: implement support for PC-relative group relocations Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 12/32] ARM: assembler: add optimized ldr/str macros to load variables from memory Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel [this message]
2022-01-24 17:47 ` [PATCH v5 13/32] ARM: percpu: add SMP_ON_UP support Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 14/32] ARM: use TLS register for 'current' on !SMP as well Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 15/32] ARM: smp: defer TPIDRURO update for SMP v6 configurations too Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 16/32] ARM: implement THREAD_INFO_IN_TASK for uniprocessor systems Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 17/32] ARM: assembler: introduce bl_r macro Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 18/32] ARM: unwind: support unwinding across multiple stacks Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 19/32] ARM: export dump_mem() to other objects Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 20/32] ARM: unwind: dump exception stack from calling frame Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 21/32] ARM: backtrace-clang: avoid crash on bogus frame pointer Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 22/32] ARM: implement IRQ stacks Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 23/32] ARM: call_with_stack: add unwind support Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 24/32] ARM: run softirqs on the per-CPU IRQ stack Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-03-22 9:04 ` Sebastian Andrzej Siewior
2022-03-22 9:04 ` Sebastian Andrzej Siewior
2022-03-22 9:35 ` Ard Biesheuvel
2022-03-22 9:35 ` Ard Biesheuvel
2022-03-22 11:29 ` Sebastian Andrzej Siewior
2022-03-22 11:29 ` Sebastian Andrzej Siewior
2022-01-24 17:47 ` [PATCH v5 25/32] ARM: memcpy: use frame pointer as unwind anchor Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 26/32] ARM: memmove: " Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 27/32] ARM: memset: clean up unwind annotations Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 28/32] ARM: unwind: disregard unwind info before stack frame is set up Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 29/32] ARM: entry: rework stack realignment code in svc_entry Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 30/32] ARM: switch_to: clean up Thumb2 code path Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 31/32] ARM: mm: prepare vmalloc_seq handling for use under SMP Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:47 ` [PATCH v5 32/32] ARM: implement support for vmap'ed stacks Ard Biesheuvel
2022-01-24 17:47 ` Ard Biesheuvel
2022-01-24 17:56 ` [PATCH v5 00/32] ARM vmap'ed and IRQ stacks roundup Russell King (Oracle)
2022-01-24 17:56 ` Russell King (Oracle)
2022-01-24 17:57 ` Ard Biesheuvel
2022-01-24 17:57 ` Ard Biesheuvel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220124174744.1054712-14-ardb@kernel.org \
--to=ardb@kernel.org \
--cc=arnd@arndb.de \
--cc=keescook@chromium.org \
--cc=keithpac@amazon.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-hardening@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=maz@kernel.org \
--cc=mr.bossman075@gmail.com \
--cc=ndesaulniers@google.com \
--cc=nico@fluxnic.net \
--cc=tony@atomide.com \
--cc=vladimir.murzin@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.