Re: [PATCH 2/2] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro

["Ondřej Jirman" <megous@megous.com>]

Hi Tom,

On Sun, May 29, 2022 at 01:17:05PM +1000, Tom Fitzhenry wrote:
> This is a basic DT that includes only features that are already
> supported by mainline drivers.
> 
> Tested to work: booting from eMMC, WiFi, charging.
> 
> Future patches will flesh out the DT. Some components, e.g. the panel,
> are awaiting driver mainlining.
> 
> This is derived from a combination of https://gitlab.com/pine64-org/linux
> and https://megous.com/git/linux.

this patch has a bunch of issues that were already fixed during discussions
with Martijn as part of his effort to prepare an initial device tree for
PinephonePro. (also noted below for your reference)

I suggest to wait for the original author's submission.

kind regards,
	o.

> https://wiki.pine64.org/wiki/PinePhone_Pro
> 
> Co-developed-by: Ondrej Jirman <megous@megous.com>
> Co-developed-by: Martijn Braam <martijn@brixit.nl>
> Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
> ---
>  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
>  .../dts/rockchip/rk3399-pinephone-pro.dts     | 939 ++++++++++++++++++
>  2 files changed, 940 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> 
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 4ae9f35434b8..c00e7922d974 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -41,6 +41,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-r4s.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinephone-pro.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> new file mode 100644
> index 000000000000..b1a486db1dfe
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> @@ -0,0 +1,939 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2020 Martijn Braam <martijn@brixit.nl>
> + * Copyright (c) 2021 Kamil Trzciński <ayufan@ayufan.eu>
> + */
> +
> +// PinePhone Pro datasheet: https://files.pine64.org/doc/PinePhonePro/PinephonePro-Schematic-V1.0-20211127.pdf
> +
> +/dts-v1/;
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/usb/pd.h>
> +#include <dt-bindings/leds/common.h>
> +#include "rk3399.dtsi"
> +#include "rk3399-opp.dtsi"
> +
> +/ {
> +	model = "Pine64 PinePhonePro";
> +	compatible = "pine64,pinephone-pro", "rockchip,rk3399";
> +
> +	chosen {
> +		bootargs = "earlycon=uart8250,mmio32,0xff1a0000";
> +		stdout-path = "serial2:115200n8";
> +	};
> +
> +	// Per "RK 3399 SARADC", page 8.
> +	adc-keys {
> +		compatible = "adc-keys";
> +		io-channels = <&saradc 1>;
> +		io-channel-names = "buttons";
> +		keyup-threshold-microvolt = <1600000>;
> +		poll-interval = <100>;
> +
> +		button-up {
> +			label = "Volume Up";
> +			linux,code = <KEY_VOLUMEUP>;
> +			press-threshold-microvolt = <100000>;
> +		};
> +
> +		button-down {
> +			label = "Volume Down";
> +			linux,code = <KEY_VOLUMEDOWN>;
> +			press-threshold-microvolt = <300000>;
> +		};
> +	};
> +
> +	cluster1_opp_ppp: opp-table1b {
> +		compatible = "operating-points-v2";
> +		opp-shared;
> +
> +		opp00 {
> +			opp-hz = /bits/ 64 <408000000>;
> +			opp-microvolt = <800000>;
> +			clock-latency-ns = <40000>;
> +		};
> +		opp01 {
> +			opp-hz = /bits/ 64 <600000000>;
> +			opp-microvolt = <800000>;
> +		};
> +		opp02 {
> +			opp-hz = /bits/ 64 <816000000>;
> +			opp-microvolt = <825000>;
> +		};
> +		opp03 {
> +			opp-hz = /bits/ 64 <1008000000>;
> +			opp-microvolt = <875000>;
> +		};
> +		opp04 {
> +			opp-hz = /bits/ 64 <1200000000>;
> +			opp-microvolt = <950000>;
> +		};
> +		opp05 {
> +			opp-hz = /bits/ 64 <1416000000>;
> +			opp-microvolt = <1025000>;
> +		};
> +	};
> +
> +	// Per "BACKLIGHT", page 16.
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm0 0 1000000 0>;
> +		pwm-delay-us = <10000>;
> +	};
> +
> +	// Per "RK3399 GPIO", page 11.
> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&red_led_pin &green_led_pin &blue_led_pin>;
> +
> +		led-standby {
> +			color = <LED_COLOR_ID_RED>;
> +			default-state = "off";
> +			function = LED_FUNCTION_STANDBY;
> +			gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
> +			label = "red:standby";
> +			panic-indicator;
> +			retain-state-suspended;
> +		};
> +
> +		led-pwr {
> +			color = <LED_COLOR_ID_GREEN>;
> +			default-state = "on";
> +			function = LED_FUNCTION_POWER;
> +			gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_HIGH>;
> +			label = "green:disk-activity";
> +		};
> +
> +		blue-charging {
> +			color = <LED_COLOR_ID_BLUE>;
> +			default-state = "off";
> +			function = LED_FUNCTION_CHARGING;
> +			gpios = <&gpio4 RK_PD6 GPIO_ACTIVE_HIGH>;
> +			label = "blue:charging";
> +		};
> +	};

^^ these are general indicator LEDs, they don't have a function marked on the
chasis of the phone.

> +	gpio-key-power {
> +		compatible = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pwrbtn_pin>;
> +
> +		power {
> +			debounce-interval = <20>;
> +			// Per "PMU Controler", page 4.
> +			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> +			label = "Power";
> +			linux,code = <KEY_POWER>;
> +			wakeup-source;
> +		};
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		clocks = <&rk818 1>;
> +		clock-names = "ext_clock";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wifi_enable_h>;
> +		post-power-on-delay-ms = <100>;
> +		power-off-delay-us = <500000>;
> +
> +		/* WL_REG_ON on module */
> +		reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	vibrator {
> +		compatible = "gpio-vibrator";
> +		// Per "GPIO", page 11.
> +		enable-gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_HIGH>;
> +		// Per "Motor", page 17.
> +		vcc-supply = <&vcc3v3_sys>;
> +	};
> +
> +	/* Power tree */
> +	/* Root power source */
> +	vcc_sysin: vcc-sysin {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_sysin";
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	vcc5v0_sys: vcc5v0-host-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_sys";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +		vin-supply = <&vcc_sysin>;
> +
> +		regulator-state-mem {
> +			regulator-on-in-suspend;
> +		};
> +	};
> +
> +	vcc5v0_typec: vcc5v0-typec-regulator {
> +		compatible = "regulator-fixed";
> +		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vcc5v0_typec_en>;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-name = "vcc5v0_typec";
> +		vin-supply = <&vcc5v0_sys>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +
> +		regulator-state-mem {
> +			regulator-on-in-suspend;
> +		};
> +	};

^^^ this is not a regulator and doesn't switch on VBUS supply
for type-c port. That's done by the otg_switch

> +	/* Main 3.3v supply */
> +	vcc3v3_sys: wifi_bat: vcc3v3-sys {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc3v3_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_sysin>;
> +
> +		regulator-state-mem {
> +			regulator-on-in-suspend;
> +		};
> +	};
> +
> +	vcc1v8_codec: vcc1v8-codec-regulator {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio3 RK_PA4 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vcc1v8_codec_en>;
> +		regulator-name = "vcc1v8_codec";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vcc3v3_sys>;
> +	};
> +
> +	/* MIPI DSI panel 1.8v supply */
> +	vcc1v8_lcd: vcc1v8-lcd {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		regulator-name = "vcc1v8_lcd";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vcc3v3_sys>;
> +		gpio = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&display_pwren1>;
> +	};
> +
> +	/* MIPI DSI panel 2.8v supply */
> +	vcc2v8_lcd: vcc2v8-lcd {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		regulator-name = "vcc2v8_lcd";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&vcc3v3_sys>;
> +		gpio = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&display_pwren>;
> +	};
> +
> +	vcca1v8_s3: vcc1v8-s3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcca1v8_s3";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vcc3v3_sys>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +};
> +
> +&cpu_l0 {
> +	cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l1 {
> +	cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l2 {
> +	cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l3 {
> +	cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_b0 {
> +	cpu-supply = <&vdd_cpu_b>;
> +	operating-points-v2 = <&cluster1_opp_ppp>;
> +};
> +
> +&cpu_b1 {
> +	cpu-supply = <&vdd_cpu_b>;
> +	operating-points-v2 = <&cluster1_opp_ppp>;
> +};
> +
> +&emmc_phy {
> +	status = "okay";
> +};
> +
> +&gpu {
> +	mali-supply = <&vdd_gpu>;
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	// Per "SCL clock frequency", page 30, RK818 datasheet.
> +	clock-frequency = <400000>;
> +	i2c-scl-rising-time-ns = <168>;
> +	i2c-scl-falling-time-ns = <4>;
> +	status = "okay";
> +
> +	// Per "PMIC RK818-3", page 13.
> +	rk818: pmic@1c {
> +		compatible = "rockchip,rk818";
> +		reg = <0x1c>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <RK_PC5 IRQ_TYPE_LEVEL_LOW>;
> +		#clock-cells = <1>;
> +		clock-output-names = "xin32k", "rk808-clkout2";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pmic_int_l>;
> +		rockchip,system-power-controller;
> +		wakeup-source;
> +		extcon = <&fusb0>;

rk818 doesn't use extcon interface

> +		vcc1-supply = <&vcc_sysin>;
> +		vcc2-supply = <&vcc_sysin>;
> +		vcc3-supply = <&vcc_sysin>;
> +		vcc4-supply = <&vcc_sysin>;
> +		vcc6-supply = <&vcc_sysin>;
> +		vcc7-supply = <&vcc3v3_sys>;
> +		vcc8-supply = <&vcc_sysin>;
> +		vcc9-supply = <&vcc3v3_sys>;
> +
> +		regulators {
> +			vdd_cpu_l: DCDC_REG1 {
> +				regulator-name = "vdd_cpu_l";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <750000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-ramp-delay = <6001>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdd_center: DCDC_REG2 {
> +				regulator-name = "vdd_center";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-ramp-delay = <6001>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			// DDR
> +			vcc_ddr: DCDC_REG3 {
> +				regulator-name = "vcc_ddr";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-state-mem {
> +					// Power RAM while suspended.
> +					regulator-on-in-suspend;
> +				};
> +			};
> +
> +			vcc_1v8: vcc_wl: DCDC_REG4 {
> +				regulator-name = "vcc_1v8";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			// Audio codec.
> +			vcca3v0_codec: LDO_REG1 {
> +				regulator-name = "vcca3v0_codec";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			// Touch screen.
> +			vcc3v0_touch: LDO_REG2 {
> +				regulator-name = "vcc3v0_touch";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcca1v8_codec: LDO_REG3 {
> +				regulator-name = "vcca1v8_codec";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_power_on: LDO_REG4 {
> +				regulator-name = "vcc_power_on";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3300000>;
> +				};
> +			};
> +
> +			vcc_3v0: LDO_REG5 {
> +				regulator-name = "vcc_3v0";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3000000>;
> +				};
> +			};
> +
> +			vcc_1v5: LDO_REG6 {
> +				regulator-name = "vcc_1v5";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1500000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1500000>;
> +				};
> +			};
> +
> +			vcc1v8_dvp: LDO_REG7 {
> +				regulator-name = "vcc1v8_dvp";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc3v3_s3: LDO_REG8 {
> +				regulator-name = "vcc3v3_s3";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vccio_sd: LDO_REG9 {
> +				regulator-name = "vccio_sd";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3300000>;
> +				};
> +			};
> +
> +			vcc3v3_s0: SWITCH_REG {
> +				regulator-name = "vcc3v3_s0";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +				};
> +			};
> +
> +			boost_otg: DCDC_BOOST {
> +				regulator-name = "boost_otg";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <5000000>;
> +				regulator-max-microvolt = <5000000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <5000000>;
> +				};
> +			};
> +
> +			otg_switch: OTG_SWITCH {
> +				regulator-name = "otg_switch";
> +			};
> +		};
> +	};
> +
> +	vdd_cpu_b: regulator@40 {
> +		compatible = "silergy,syr827";
> +		reg = <0x40>;
> +		fcs,suspend-voltage-selector = <1>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vsel1_pin>;
> +		regulator-name = "vdd_cpu_b";
> +		regulator-min-microvolt = <712500>;
> +		regulator-max-microvolt = <1500000>;
> +		regulator-ramp-delay = <1000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +
> +	vdd_gpu: regulator@41 {
> +		compatible = "silergy,syr828";
> +		reg = <0x41>;
> +		fcs,suspend-voltage-selector = <1>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vsel2_pin>;
> +		regulator-name = "vdd_gpu";
> +		regulator-min-microvolt = <712500>;
> +		regulator-max-microvolt = <1500000>;
> +		regulator-ramp-delay = <1000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	i2c-scl-rising-time-ns = <300>;
> +	i2c-scl-falling-time-ns = <15>;
> +	status = "okay";
> +};
> +
> +&i2c3 {
> +	i2c-scl-rising-time-ns = <450>;
> +	i2c-scl-falling-time-ns = <15>;
> +	status = "okay";
> +
> +	// Per "Ambient Light", page 17.
> +	light-sensor@48 {
> +		compatible = "sensortek,stk3311";
> +		reg = <0x48>;
> +		interrupt-parent = <&gpio4>;
> +		interrupts = <RK_PD3 IRQ_TYPE_EDGE_FALLING>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&stk3311_int>;
> +		vdd-supply = <&vcc_3v0>;
> +		leda-supply = <&vcc_3v0>;
> +	};
> +};
> +
> +&i2c4 {
> +	i2c-scl-rising-time-ns = <600>;
> +	i2c-scl-falling-time-ns = <20>;
> +	status = "okay";
> +
> +	// Per "TYPE-C", page 23.
> +	fusb0: typec-portc@22 {
> +		compatible = "fcs,fusb302";
> +		reg = <0x22>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&fusb0_int>;
> +		vbus-supply = <&vcc5v0_typec>;
> +
> +		connector {
> +			compatible = "usb-c-connector";
> +			data-role = "dual";
> +			label = "USB-C";
> +			op-sink-microwatt = <1000000>;
> +			power-role = "dual";
> +			sink-pdos =
> +				<PDO_FIXED(5000, 2500, PDO_FIXED_USB_COMM)>;
> +			source-pdos =
> +				<PDO_FIXED(5000, 1400, PDO_FIXED_USB_COMM)>;
> +			try-power-role = "sink";
> +
> +			extcon-cables = <1 2 5 6 9 10 12 44>;
> +			typec-altmodes = <0xff01 1 0x001c0c00 1>;

^^^ these are not mainline bindings

Mainline uses mode-switch / orientation-switch / usb-role-switch properties and
altmodes node. Specified VDO (0x001c0c00) is also incorrect. And I don't think
the phone can provide 1.4A at 5V (that would be 7W)

VCC5V0_SYS can provide at most 2A and it's shared between modem, power amp for
the speaker, and type-c VCONN which also has some power requirements (1W).


> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +
> +					usbc_hs: endpoint {
> +						remote-endpoint =
> +							<&u2phy0_typec_hs>;
> +					};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +
> +					usbc_ss: endpoint {
> +						remote-endpoint =
> +							<&tcphy0_typec_ss>;
> +					};
> +				};
> +
> +				port@2 {
> +					reg = <2>;
> +
> +					usbc_dp: endpoint {
> +						remote-endpoint =
> +							<&tcphy0_typec_dp>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	// Per "Gyro", page 17.
> +	accelerometer@68 {
> +		compatible = "invensense,mpu6500";
> +		reg = <0x68>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <RK_PC6 IRQ_TYPE_LEVEL_LOW>;
> +		vdd-supply = <&vcc_1v8>;
> +		vddio-supply = <&vcc_1v8>;
> +
> +		mount-matrix =
> +			"1", "0", "0",
> +			"0", "-1", "0",
> +			"0", "0", "1";
> +	};
> +};
> +
> +&io_domains {
> +	status = "okay";
> +
> +	bt656-supply = <&vcc1v8_dvp>;
> +	audio-supply = <&vcca1v8_codec>;
> +	sdmmc-supply = <&vccio_sd>;
> +	gpio1830-supply = <&vcc_3v0>;
> +};
> +
> +&pmu_io_domains {
> +	pmu1830-supply = <&vcc_1v8>;
> +	status = "okay";
> +};
> +
> +&pinctrl {
> +	bt {
> +		bt_enable_h: bt-enable-h {
> +			rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		bt_host_wake_l: bt-host-wake-l {
> +			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
> +		};
> +
> +		bt_wake_l: bt-wake-l {
> +			rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	buttons {
> +		pwrbtn_pin: pwrbtn-pin {
> +			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +	};
> +
> +	fusb302x {
> +		fusb0_int: fusb0-int {
> +			rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +	};
> +
> +	leds {
> +		red_led_pin: red-led-pin {
> +			rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		green_led_pin: green-led-pin {
> +			rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		blue_led_pin: blue-led-pin {
> +			rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	pmic {
> +		pmic_int_l: pmic-int-l {
> +			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +
> +		vsel1_pin: vsel1-pin {
> +			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
> +		};
> +
> +		vsel2_pin: vsel2-pin {
> +			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
> +		};
> +	};
> +
> +	sdcard {
> +		sdmmc0_pwr_h: sdmmc0-pwr-h {
> +			rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +	};
> +
> +	sdio-pwrseq {
> +		wifi_enable_h: wifi-enable-h {
> +			rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	usb-typec {
> +		vcc5v0_typec_en: vcc5v0_typec_en {
> +			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +	};
> +
> +	dsi {
> +		display_rst_l: display-rst-l {
> +			rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_down>;
> +		};
> +
> +		display_pwren: display-pwren {
> +			rockchip,pins = <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_down>;
> +		};
> +
> +		display_pwren1: display-pwren1 {
> +			rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_down>;
> +		};
> +	};
> +
> +	stk3311 {
> +		stk3311_int: stk3311-int {
> +			rockchip,pins = <4 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +	};
> +
> +	sound {
> +		vcc1v8_codec_en: vcc1v8-codec-en {
> +			rockchip,pins = <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
> +		};
> +	};
> +};
> +
> +&pwm0 {
> +	status = "okay";
> +};
> +
> +&pwm1 {
> +	status = "okay";
> +};
> +
> +&pwm2 {
> +	status = "okay";
> +};
> +
> +// Per "SARADC", page 8.
> +&saradc {
> +	vref-supply = <&vcca1v8_s3>;
> +	status = "okay";
> +};
> +
> +&sdio0 {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	cap-sdio-irq;
> +	disable-wp;
> +	keep-power-in-suspend;
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
> +	sd-uhs-sdr104;
> +	status = "okay";
> +};
> +
> +// Per "SDMMC Controler", page 6.
> +&sdmmc {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
> +	disable-wp;
> +	max-frequency = <150000000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
> +	vmmc-supply = <&vcc3v3_sys>;
> +	vqmmc-supply = <&vccio_sd>;
> +	status = "okay";
> +};
> +
> +&sdhci {
> +	bus-width = <8>;
> +	mmc-hs200-1_8v;
> +	non-removable;
> +	status = "okay";
> +};
> +
> +&tcphy0 {
> +	extcon = <&fusb0>;
> +	status = "okay";
> +};

^^^ this does not work. fusb0 doesn't provide any extcon interface
it only consumes one, just like tcphy0

> +&tcphy0_dp {
> +	port {
> +		tcphy0_typec_dp: endpoint {
> +			remote-endpoint = <&usbc_dp>;
> +		};
> +	};
> +};
> +
> +&tcphy0_usb3 {
> +	port {
> +		tcphy0_typec_ss: endpoint {
> +			remote-endpoint = <&usbc_ss>;
> +		};
> +	};
> +};
> +
> +// Enable thermal sensors.
> +&tsadc {
> +	/* tshut mode 0:CRU 1:GPIO */
> +	rockchip,hw-tshut-mode = <1>;
> +	/* tshut polarity 0:LOW 1:HIGH */
> +	rockchip,hw-tshut-polarity = <1>;
> +	status = "okay";
> +};
> +
> +&u2phy0 {
> +	status = "okay";
> +
> +	u2phy0_otg: otg-port {
> +		status = "okay";
> +	};
> +
> +	u2phy0_host: host-port {
> +		status = "okay";
> +		phy-supply = <&vcc5v0_sys>;
> +	};
> +
> +	port {
> +		u2phy0_typec_hs: endpoint {
> +			remote-endpoint = <&usbc_hs>;
> +		};
> +	};
> +};
> +
> +&u2phy1 {
> +	status = "okay";
> +
> +	u2phy1_otg: otg-port {
> +		status = "okay";
> +	};
> +
> +	u2phy1_host: host-port {
> +		status = "okay";
> +		phy-supply = <&vcc5v0_sys>;
> +	};
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
> +	uart-has-rtscts;
> +	status = "okay";
> +
> +	// Per "WIFI/BT MODULE", page 19.
> +	bluetooth {
> +		compatible = "brcm,bcm4345c5";
> +		clocks = <&rk818 1>;
> +		clock-names = "lpo";
> +		device-wakeup-gpios = <&gpio2 RK_PD2 GPIO_ACTIVE_HIGH>;
> +		host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
> +		max-speed = <1500000>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
> +		shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
> +		vbat-supply = <&wifi_bat>;
> +		vddio-supply = <&vcc_wl>;
> +	};
> +};
> +
> +&uart2 {
> +	status = "okay";
> +};
> +
> +&usb_host0_ehci {
> +	status = "okay";
> +};
> +
> +&usb_host0_ohci {
> +	status = "okay";
> +};
> +
> +&usb_host1_ehci {
> +	status = "okay";
> +};
> +
> +&usb_host1_ohci {
> +	status = "okay";
> +};
> +
> +&usbdrd3_0 {
> +	status = "okay";
> +};
> +
> +&usbdrd_dwc3_0 {
> +	dr_mode = "peripheral";
> +	status = "okay";
> +};
> +
> +&vopb {
> +	status = "okay";
> +};
> +
> +&vopb_mmu {
> +	status = "okay";
> +};
> +
> +&vopl {
> +	status = "okay";
> +};
> +
> +&vopl_mmu {
> +	status = "okay";
> +};
> -- 
> 2.36.0
> 

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip