From: jrodrigues <jrodrigues@ubimet.com>
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, jrodrigues@ubimet.com
Subject: [PATCH] ARM: dts: imx: tqma7: add lm75a sensor (rev. 01xxx)
Date: Fri, 27 Oct 2023 21:15:48 +0200 [thread overview]
Message-ID: <20231027211548.21a6cee7@pcn112> (raw)
TQMa7x (revision 01xxx) uses a different (LM75A) temperature sensor.
The two sensors use different I2C address, so we can set both sensors
simultaneously.
Signed-off-by: João Rodrigues <jrodrigues@ubimet.com>
---
arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
index fe42b0a468..b87560d037 100644
--- a/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
@@ -128,7 +128,14 @@ vgen6_reg: vldo4 {
};
};
- /* NXP SE97BTP with temperature sensor + eeprom */
+ /* LM75A - temperature sensor, TQMa7x 01xx */
+ lm75a: temperature-sensor@48 {
+ compatible = "national,lm75a";
+ reg = <0x48>;
+ status = "okay";
+ };
+
+ /* NXP SE97BTP with temperature sensor + eeprom, TQMa7x 02xx */
se97b: temperature-sensor-eeprom@1e {
compatible = "nxp,se97b", "jedec,jc-42.4-temp";
reg = <0x1e>;
--
The differences in the ICs are shown here:
The TQMa7 manual only references the latest version
https://www.tq-group.com/filedownloads/files/products/embedded/manuals/arm/embedded-modul/TQ-Socket/TQMa7x/TQMa7x.UM.0203.pdf
in section 3.2.4, while the board manual
https://www.tq-group.com/filedownloads/files/products/embedded/manuals/arm/carrierboard/MBa7x/MBa7x.UM.0101.pdf
in section 4.1.2 references the old version, introduced by this patch.
I have tested this change in a board which uses the TQMa7x
module, and with this patch we always a temperature sensors available.
Best regards,
--
João Rodrigues <jrodrigues@ubimet.com>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: jrodrigues <jrodrigues@ubimet.com>
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, jrodrigues@ubimet.com
Subject: [PATCH] ARM: dts: imx: tqma7: add lm75a sensor (rev. 01xxx)
Date: Fri, 27 Oct 2023 21:15:48 +0200 [thread overview]
Message-ID: <20231027211548.21a6cee7@pcn112> (raw)
TQMa7x (revision 01xxx) uses a different (LM75A) temperature sensor.
The two sensors use different I2C address, so we can set both sensors
simultaneously.
Signed-off-by: João Rodrigues <jrodrigues@ubimet.com>
---
arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
index fe42b0a468..b87560d037 100644
--- a/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
@@ -128,7 +128,14 @@ vgen6_reg: vldo4 {
};
};
- /* NXP SE97BTP with temperature sensor + eeprom */
+ /* LM75A - temperature sensor, TQMa7x 01xx */
+ lm75a: temperature-sensor@48 {
+ compatible = "national,lm75a";
+ reg = <0x48>;
+ status = "okay";
+ };
+
+ /* NXP SE97BTP with temperature sensor + eeprom, TQMa7x 02xx */
se97b: temperature-sensor-eeprom@1e {
compatible = "nxp,se97b", "jedec,jc-42.4-temp";
reg = <0x1e>;
--
The differences in the ICs are shown here:
The TQMa7 manual only references the latest version
https://www.tq-group.com/filedownloads/files/products/embedded/manuals/arm/embedded-modul/TQ-Socket/TQMa7x/TQMa7x.UM.0203.pdf
in section 3.2.4, while the board manual
https://www.tq-group.com/filedownloads/files/products/embedded/manuals/arm/carrierboard/MBa7x/MBa7x.UM.0101.pdf
in section 4.1.2 references the old version, introduced by this patch.
I have tested this change in a board which uses the TQMa7x
module, and with this patch we always a temperature sensors available.
Best regards,
--
João Rodrigues <jrodrigues@ubimet.com>
WARNING: multiple messages have this Message-ID (diff)
From: jrodrigues <jrodrigues@ubimet.com>
To: unlisted-recipients:; (no To-header on input)
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, jrodrigues@ubimet.com
Subject: [PATCH] ARM: dts: imx: tqma7: add lm75a sensor (rev. 01xxx)
Date: Fri, 27 Oct 2023 21:15:48 +0200 [thread overview]
Message-ID: <20231027211548.21a6cee7@pcn112> (raw)
TQMa7x (revision 01xxx) uses a different (LM75A) temperature sensor.
The two sensors use different I2C address, so we can set both sensors
simultaneously.
Signed-off-by: João Rodrigues <jrodrigues@ubimet.com>
---
arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
index fe42b0a468..b87560d037 100644
--- a/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
@@ -128,7 +128,14 @@ vgen6_reg: vldo4 {
};
};
- /* NXP SE97BTP with temperature sensor + eeprom */
+ /* LM75A - temperature sensor, TQMa7x 01xx */
+ lm75a: temperature-sensor@48 {
+ compatible = "national,lm75a";
+ reg = <0x48>;
+ status = "okay";
+ };
+
+ /* NXP SE97BTP with temperature sensor + eeprom, TQMa7x 02xx */
se97b: temperature-sensor-eeprom@1e {
compatible = "nxp,se97b", "jedec,jc-42.4-temp";
reg = <0x1e>;
--
The differences in the ICs are shown here:
The TQMa7 manual only references the latest version
https://www.tq-group.com/filedownloads/files/products/embedded/manuals/arm/embedded-modul/TQ-Socket/TQMa7x/TQMa7x.UM.0203.pdf
in section 3.2.4, while the board manual
https://www.tq-group.com/filedownloads/files/products/embedded/manuals/arm/carrierboard/MBa7x/MBa7x.UM.0101.pdf
in section 4.1.2 references the old version, introduced by this patch.
I have tested this change in a board which uses the TQMa7x
module, and with this patch we always a temperature sensors available.
Best regards,
--
João Rodrigues <jrodrigues@ubimet.com>
next reply other threads:[~2023-10-27 19:25 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-10-27 19:15 jrodrigues [this message]
2023-10-27 19:15 ` [PATCH] ARM: dts: imx: tqma7: add lm75a sensor (rev. 01xxx) jrodrigues
2023-10-27 19:15 ` jrodrigues
2023-10-29 8:13 ` Krzysztof Kozlowski
2023-10-29 8:13 ` Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20231027211548.21a6cee7@pcn112 \
--to=jrodrigues@ubimet.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.