Re: [PATCH v5 03/12] dt-bindings: mtd: brcmnand: Add ecc strap property

From: Miquel Raynal <miquel.raynal@bootlin.com>
To: William Zhang <william.zhang@broadcom.com>
Cc: Linux MTD List <linux-mtd@lists.infradead.org>,
	Linux ARM List <linux-arm-kernel@lists.infradead.org>,
	Broadcom Kernel List <bcm-kernel-feedback-list@broadcom.com>,
	f.fainelli@gmail.com, kursad.oney@broadcom.com,
	joel.peshkin@broadcom.com, anand.gore@broadcom.com,
	dregan@mail.com, kamal.dasu@broadcom.com,
	tomer.yacoby@broadcom.com, dan.beygelman@broadcom.com,
	devicetree@vger.kernel.org,
	Brian Norris <computersforpeace@gmail.com>,
	linux-kernel@vger.kernel.org, Conor Dooley <conor+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Richard Weinberger <richard@nod.at>,
	Kamal Dasu <kdasu.kdev@gmail.com>,
	Rob Herring <robh+dt@kernel.org>
Subject: Re: [PATCH v5 03/12] dt-bindings: mtd: brcmnand: Add ecc strap property
Date: Tue, 20 Feb 2024 10:56:34 +0100	[thread overview]
Message-ID: <20240220105634.02b505b6@xps-13> (raw)
In-Reply-To: <20240207202257.271784-4-william.zhang@broadcom.com>

Hi William,

william.zhang@broadcom.com wrote on Wed,  7 Feb 2024 12:22:48 -0800:

> Add brcm,nand-ecc-use-strap to get ecc and spare area size settings from
> board boot strap for broadband board designs because they do not specify
> ecc setting in dts but rather using the strap setting.
> 
> Signed-off-by: William Zhang <william.zhang@broadcom.com>
> 
> ---
> 
> Changes in v5:
> - Update the description for this ecc strap property
> - Add check to make sure brcm,nand-ecc-use-strap and
>   nand-ecc-strength/brcm,nand-oob-sector-size can not be used at the
>   same time
> 
> Changes in v4:
> - Move ecc strap property to this separate patch and remove some
> non-binding related text from the description
> 
> Changes in v3: None
> Changes in v2: None
> 
>  .../bindings/mtd/brcm,brcmnand.yaml           | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.yaml b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.yaml
> index 6a717bcedfd3..52a4c993b6f1 100644
> --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.yaml
> +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.yaml
> @@ -146,6 +146,13 @@ patternProperties:
>            layout.
>          $ref: /schemas/types.yaml#/definitions/uint32
>  
> +      brcm,nand-ecc-use-strap:
> +        description:
> +          This property requires the host system to get the ECC strength
> +          and step size from the SoC NAND boot strap setting. This is a
> +          common hardware design on BCMBCA based boards.
> +        $ref: /schemas/types.yaml#/definitions/flag
> +
>      unevaluatedProperties: false
>  
>  allOf:
> @@ -195,6 +202,18 @@ allOf:
>        required:
>          - interrupt-names
>  
> +  - if:
> +      patternProperties:
> +        "^nand@[a-f0-9]$":
> +          required:
> +            - brcm,nand-ecc-use-strap
> +    then:
> +      patternProperties:
> +        "^nand@[a-f0-9]$":
> +          properties:
> +            nand-ecc-strength: false
> +            brcm,nand-oob-sector-size: false

Can you also excluse all the other nand-ecc- settings and brcm,
settings as well? Either you use the strap *or* you provide values in
the DT, but not both.

> +
>  unevaluatedProperties: false
>  
>  required:

Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/