From: Hal Feng <hal.feng@starfivetech.com>
To: Conor Dooley <conor+dt@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Palmer Dabbelt <palmer@dabbelt.com>,
"Rafael J . Wysocki" <rafael@kernel.org>,
Viresh Kumar <viresh.kumar@linaro.org>,
Emil Renner Berthing <emil.renner.berthing@canonical.com>,
Heinrich Schuchardt <heinrich.schuchardt@canonical.com>,
E Shattow <e@freeshell.de>, Paul Walmsley <pjw@kernel.org>,
Albert Ou <aou@eecs.berkeley.edu>
Cc: Hal Feng <hal.feng@starfivetech.com>,
devicetree@vger.kernel.org, linux-riscv@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v1 4/7] riscv: dts: starfive: jh7110-common: Move out some nodes to the board dts
Date: Thu, 16 Oct 2025 16:00:51 +0800 [thread overview]
Message-ID: <20251016080054.12484-5-hal.feng@starfivetech.com> (raw)
In-Reply-To: <20251016080054.12484-1-hal.feng@starfivetech.com>
Some node in this file are not used by the upcoming VisionFive 2 Lite
board. Move them to the board dts to prepare for adding the new
VisionFive 2 Lite device tree.
Reviewed-by: E Shattow <e@freeshell.de>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
---
.../boot/dts/starfive/jh7110-common.dtsi | 19 --------
.../jh7110-deepcomputing-fml13v01.dts | 46 +++++++++++++++++++
.../boot/dts/starfive/jh7110-milkv-mars.dts | 46 +++++++++++++++++++
.../dts/starfive/jh7110-milkv-marscm-emmc.dts | 9 ++++
.../dts/starfive/jh7110-milkv-marscm-lite.dts | 1 +
.../dts/starfive/jh7110-milkv-marscm.dtsi | 32 +++++++++++++
.../dts/starfive/jh7110-pine64-star64.dts | 46 +++++++++++++++++++
.../jh7110-starfive-visionfive-2.dtsi | 43 +++++++++++++++++
arch/riscv/boot/dts/starfive/jh7110.dtsi | 16 -------
9 files changed, 223 insertions(+), 35 deletions(-)
diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
index 5dc15e48b74b..8cfe8033305d 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
@@ -281,14 +281,8 @@ &mmc0 {
assigned-clock-rates = <50000000>;
bus-width = <8>;
bootph-pre-ram;
- cap-mmc-highspeed;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
- cap-mmc-hw-reset;
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&emmc_vdd>;
status = "okay";
};
@@ -298,8 +292,6 @@ &mmc1 {
assigned-clock-rates = <50000000>;
bus-width = <4>;
bootph-pre-ram;
- cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
- disable-wp;
cap-sd-highspeed;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
@@ -444,17 +436,6 @@ GPOEN_SYS_I2C6_DATA,
};
mmc0_pins: mmc0-0 {
- rst-pins {
- pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
- GPOEN_ENABLE,
- GPI_NONE)>;
- bias-pull-up;
- drive-strength = <12>;
- input-disable;
- input-schmitt-disable;
- slew-rate = <0>;
- };
-
mmc-pins {
pinmux = <PINMUX(PAD_SD0_CLK, 0)>,
<PINMUX(PAD_SD0_CMD, 0)>,
diff --git a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
index f2857d021d68..7535d62201f1 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
@@ -11,6 +11,52 @@ / {
compatible = "deepcomputing,fml13v01", "starfive,jh7110";
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+};
+
&pcie1 {
perst-gpios = <&sysgpio 21 GPIO_ACTIVE_LOW>;
phys = <&pciephy1>;
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
index fdaf6b4557da..c2e7a91e460a 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
@@ -11,6 +11,25 @@ / {
compatible = "milkv,mars", "starfive,jh7110";
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
@@ -22,6 +41,33 @@ &i2c0 {
status = "okay";
};
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+};
+
&pcie0 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts
index e568537af2c4..ce95496263af 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts
@@ -10,3 +10,12 @@ / {
model = "Milk-V Mars CM";
compatible = "milkv,marscm-emmc", "starfive,jh7110";
};
+
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
index 6c40d0ec4011..63aa94d65ab5 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
@@ -14,6 +14,7 @@ / {
&mmc0 {
bus-width = <4>;
cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
};
&mmc0_pins {
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi
index 25b70af564ee..af01d3abde2f 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi
@@ -21,6 +21,25 @@ sdio_pwrseq: sdio-pwrseq {
};
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
@@ -40,6 +59,19 @@ &i2c6 {
status = "disabled";
};
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
&mmc1 {
#address-cells = <1>;
#size-cells = <0>;
diff --git a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
index 31e825be2065..6faf3826c5c3 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
@@ -14,6 +14,25 @@ aliases {
};
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
starfive,tx-use-rgmii-clk;
assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
@@ -44,6 +63,33 @@ &i2c0 {
status = "okay";
};
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+};
+
&pcie1 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index 5f14afb2c24d..9cd79fe30d19 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -13,6 +13,25 @@ aliases {
};
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
status = "okay";
};
@@ -38,9 +57,33 @@ &i2c0 {
};
&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
non-removable;
};
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+};
+
&pcie0 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 6e56e9d20bb0..a380d3dabedd 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -205,22 +205,6 @@ core4 {
cpu_opp: opp-table-0 {
compatible = "operating-points-v2";
opp-shared;
- opp-375000000 {
- opp-hz = /bits/ 64 <375000000>;
- opp-microvolt = <800000>;
- };
- opp-500000000 {
- opp-hz = /bits/ 64 <500000000>;
- opp-microvolt = <800000>;
- };
- opp-750000000 {
- opp-hz = /bits/ 64 <750000000>;
- opp-microvolt = <800000>;
- };
- opp-1500000000 {
- opp-hz = /bits/ 64 <1500000000>;
- opp-microvolt = <1040000>;
- };
};
thermal-zones {
--
2.43.2
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
WARNING: multiple messages have this Message-ID (diff)
From: Hal Feng <hal.feng@starfivetech.com>
To: Conor Dooley <conor+dt@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Palmer Dabbelt <palmer@dabbelt.com>,
"Rafael J . Wysocki" <rafael@kernel.org>,
Viresh Kumar <viresh.kumar@linaro.org>,
Emil Renner Berthing <emil.renner.berthing@canonical.com>,
Heinrich Schuchardt <heinrich.schuchardt@canonical.com>,
E Shattow <e@freeshell.de>, Paul Walmsley <pjw@kernel.org>,
Albert Ou <aou@eecs.berkeley.edu>
Cc: Hal Feng <hal.feng@starfivetech.com>,
devicetree@vger.kernel.org, linux-riscv@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v1 4/7] riscv: dts: starfive: jh7110-common: Move out some nodes to the board dts
Date: Thu, 16 Oct 2025 16:00:51 +0800 [thread overview]
Message-ID: <20251016080054.12484-5-hal.feng@starfivetech.com> (raw)
In-Reply-To: <20251016080054.12484-1-hal.feng@starfivetech.com>
Some node in this file are not used by the upcoming VisionFive 2 Lite
board. Move them to the board dts to prepare for adding the new
VisionFive 2 Lite device tree.
Reviewed-by: E Shattow <e@freeshell.de>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
---
.../boot/dts/starfive/jh7110-common.dtsi | 19 --------
.../jh7110-deepcomputing-fml13v01.dts | 46 +++++++++++++++++++
.../boot/dts/starfive/jh7110-milkv-mars.dts | 46 +++++++++++++++++++
.../dts/starfive/jh7110-milkv-marscm-emmc.dts | 9 ++++
.../dts/starfive/jh7110-milkv-marscm-lite.dts | 1 +
.../dts/starfive/jh7110-milkv-marscm.dtsi | 32 +++++++++++++
.../dts/starfive/jh7110-pine64-star64.dts | 46 +++++++++++++++++++
.../jh7110-starfive-visionfive-2.dtsi | 43 +++++++++++++++++
arch/riscv/boot/dts/starfive/jh7110.dtsi | 16 -------
9 files changed, 223 insertions(+), 35 deletions(-)
diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
index 5dc15e48b74b..8cfe8033305d 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
@@ -281,14 +281,8 @@ &mmc0 {
assigned-clock-rates = <50000000>;
bus-width = <8>;
bootph-pre-ram;
- cap-mmc-highspeed;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
- cap-mmc-hw-reset;
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&emmc_vdd>;
status = "okay";
};
@@ -298,8 +292,6 @@ &mmc1 {
assigned-clock-rates = <50000000>;
bus-width = <4>;
bootph-pre-ram;
- cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
- disable-wp;
cap-sd-highspeed;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
@@ -444,17 +436,6 @@ GPOEN_SYS_I2C6_DATA,
};
mmc0_pins: mmc0-0 {
- rst-pins {
- pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
- GPOEN_ENABLE,
- GPI_NONE)>;
- bias-pull-up;
- drive-strength = <12>;
- input-disable;
- input-schmitt-disable;
- slew-rate = <0>;
- };
-
mmc-pins {
pinmux = <PINMUX(PAD_SD0_CLK, 0)>,
<PINMUX(PAD_SD0_CMD, 0)>,
diff --git a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
index f2857d021d68..7535d62201f1 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
@@ -11,6 +11,52 @@ / {
compatible = "deepcomputing,fml13v01", "starfive,jh7110";
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+};
+
&pcie1 {
perst-gpios = <&sysgpio 21 GPIO_ACTIVE_LOW>;
phys = <&pciephy1>;
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
index fdaf6b4557da..c2e7a91e460a 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
@@ -11,6 +11,25 @@ / {
compatible = "milkv,mars", "starfive,jh7110";
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
@@ -22,6 +41,33 @@ &i2c0 {
status = "okay";
};
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+};
+
&pcie0 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts
index e568537af2c4..ce95496263af 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts
@@ -10,3 +10,12 @@ / {
model = "Milk-V Mars CM";
compatible = "milkv,marscm-emmc", "starfive,jh7110";
};
+
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
index 6c40d0ec4011..63aa94d65ab5 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
@@ -14,6 +14,7 @@ / {
&mmc0 {
bus-width = <4>;
cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
};
&mmc0_pins {
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi
index 25b70af564ee..af01d3abde2f 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi
@@ -21,6 +21,25 @@ sdio_pwrseq: sdio-pwrseq {
};
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
@@ -40,6 +59,19 @@ &i2c6 {
status = "disabled";
};
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
&mmc1 {
#address-cells = <1>;
#size-cells = <0>;
diff --git a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
index 31e825be2065..6faf3826c5c3 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
@@ -14,6 +14,25 @@ aliases {
};
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
starfive,tx-use-rgmii-clk;
assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
@@ -44,6 +63,33 @@ &i2c0 {
status = "okay";
};
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+};
+
&pcie1 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index 5f14afb2c24d..9cd79fe30d19 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -13,6 +13,25 @@ aliases {
};
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
status = "okay";
};
@@ -38,9 +57,33 @@ &i2c0 {
};
&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
non-removable;
};
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+};
+
&pcie0 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 6e56e9d20bb0..a380d3dabedd 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -205,22 +205,6 @@ core4 {
cpu_opp: opp-table-0 {
compatible = "operating-points-v2";
opp-shared;
- opp-375000000 {
- opp-hz = /bits/ 64 <375000000>;
- opp-microvolt = <800000>;
- };
- opp-500000000 {
- opp-hz = /bits/ 64 <500000000>;
- opp-microvolt = <800000>;
- };
- opp-750000000 {
- opp-hz = /bits/ 64 <750000000>;
- opp-microvolt = <800000>;
- };
- opp-1500000000 {
- opp-hz = /bits/ 64 <1500000000>;
- opp-microvolt = <1040000>;
- };
};
thermal-zones {
--
2.43.2
next prev parent reply other threads:[~2025-10-16 8:01 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-16 8:00 [PATCH v1 0/7] Add support for StarFive VisionFive 2 Lite board Hal Feng
2025-10-16 8:00 ` Hal Feng
2025-10-16 8:00 ` [PATCH v1 1/7] cpufreq: dt-platdev: Add JH7110S SOC to the allowlist Hal Feng
2025-10-16 8:00 ` Hal Feng
2025-10-16 9:20 ` Heinrich Schuchardt
2025-10-16 9:20 ` Heinrich Schuchardt
2025-10-17 5:09 ` Viresh Kumar
2025-10-17 5:09 ` Viresh Kumar
2025-10-16 8:00 ` [PATCH v1 2/7] dt-bindings: PCI: starfive,jh7110-pcie: Add enable-gpios property Hal Feng
2025-10-16 8:00 ` Hal Feng
2025-10-16 8:58 ` Heinrich Schuchardt
2025-10-16 8:58 ` Heinrich Schuchardt
2025-10-16 15:51 ` Conor Dooley
2025-10-16 15:51 ` Conor Dooley
2025-10-16 8:00 ` [PATCH v1 3/7] dt-bindings: riscv: Add StarFive JH7110S SoC and VisionFive 2 Lite board Hal Feng
2025-10-16 8:00 ` Hal Feng
2025-10-16 9:24 ` Heinrich Schuchardt
2025-10-16 9:24 ` Heinrich Schuchardt
2025-10-16 15:55 ` Conor Dooley
2025-10-16 15:55 ` Conor Dooley
2025-10-16 8:00 ` Hal Feng [this message]
2025-10-16 8:00 ` [PATCH v1 4/7] riscv: dts: starfive: jh7110-common: Move out some nodes to the board dts Hal Feng
2025-10-16 15:54 ` Conor Dooley
2025-10-16 15:54 ` Conor Dooley
2025-10-16 22:55 ` E Shattow
2025-10-16 22:55 ` E Shattow
2025-11-03 5:43 ` Hal Feng
2025-11-03 5:43 ` Hal Feng
2025-10-16 8:00 ` [PATCH v1 5/7] riscv: dts: starfive: Add common board dtsi for VisionFive 2 Lite variants Hal Feng
2025-10-16 8:00 ` Hal Feng
2025-10-16 8:00 ` [PATCH v1 6/7] riscv: dts: starfive: Add VisionFive 2 Lite board device tree Hal Feng
2025-10-16 8:00 ` Hal Feng
2025-10-16 8:00 ` [PATCH v1 7/7] riscv: dts: starfive: Add VisionFive 2 Lite eMMC " Hal Feng
2025-10-16 8:00 ` Hal Feng
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251016080054.12484-5-hal.feng@starfivetech.com \
--to=hal.feng@starfivetech.com \
--cc=aou@eecs.berkeley.edu \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=e@freeshell.de \
--cc=emil.renner.berthing@canonical.com \
--cc=heinrich.schuchardt@canonical.com \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=palmer@dabbelt.com \
--cc=pjw@kernel.org \
--cc=rafael@kernel.org \
--cc=robh@kernel.org \
--cc=viresh.kumar@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.