[PATCH v3 2/2] riscv: dts: spacemit: Add OrangePi R2S board device tree

[michael.opdenacker@rootcommit.com]

From: Michael Opdenacker <michael.opdenacker@rootcommit.com>

Add initial device tree support for the OrangePi RV2 board [1], which is
marketed as using the Ky X1 SoC but has been confirmed to be
identical to the SpacemiT K1 [2].

Enable UART0, to boot into a serial console

Two Gigabit Ethernet ports with RGMII interface standard support
are enabled, each port is connected to an external
Motorcomm YT8531C PHY chip which uses the GPIO for reset control.

Enable PDMA.

Enable 8 GB eMMC chip for storage.

Link: http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-R2S.html [1]
Link: https://www.spacemit.com/en/key-stone-k1 [2]
Signed-off-by: Michael Opdenacker <michael.opdenacker@rootcommit.com>
---
 arch/riscv/boot/dts/spacemit/Makefile         |  1 +
 .../boot/dts/spacemit/k1-orangepi-r2s.dts     | 90 +++++++++++++++++++
 2 files changed, 91 insertions(+)
 create mode 100644 arch/riscv/boot/dts/spacemit/k1-orangepi-r2s.dts

diff --git a/arch/riscv/boot/dts/spacemit/Makefile b/arch/riscv/boot/dts/spacemit/Makefile
index 942ecb38bea0..96b3a13a3944 100644
--- a/arch/riscv/boot/dts/spacemit/Makefile
+++ b/arch/riscv/boot/dts/spacemit/Makefile
@@ -3,3 +3,4 @@ dtb-$(CONFIG_ARCH_SPACEMIT) += k1-bananapi-f3.dtb
 dtb-$(CONFIG_ARCH_SPACEMIT) += k1-milkv-jupiter.dtb
 dtb-$(CONFIG_ARCH_SPACEMIT) += k1-musepi-pro.dtb
 dtb-$(CONFIG_ARCH_SPACEMIT) += k1-orangepi-rv2.dtb
+dtb-$(CONFIG_ARCH_SPACEMIT) += k1-orangepi-r2s.dtb
diff --git a/arch/riscv/boot/dts/spacemit/k1-orangepi-r2s.dts b/arch/riscv/boot/dts/spacemit/k1-orangepi-r2s.dts
new file mode 100644
index 000000000000..58098c4a2aab
--- /dev/null
+++ b/arch/riscv/boot/dts/spacemit/k1-orangepi-r2s.dts
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2025 Michael Opdenacker <michael.opdenacker@rootcommit.com>
+ */
+
+/dts-v1/;
+
+#include "k1.dtsi"
+#include "k1-pinctrl.dtsi"
+
+/ {
+	model = "OrangePi R2S";
+	compatible = "xunlong,orangepi-r2s", "spacemit,k1";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+};
+
+&emmc {
+	bus-width = <8>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&eth0 {
+	phy-handle = <&rgmii0>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_cfg>;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <0>;
+	status = "okay";
+
+	mdio-bus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		reset-gpios = <&gpio K1_GPIO(110) GPIO_ACTIVE_LOW>;
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <100000>;
+
+		rgmii0: phy@1 {
+			reg = <0x1>;
+		};
+	};
+};
+
+&eth1 {
+	phy-handle = <&rgmii1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1_cfg>;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <250>;
+	status = "okay";
+
+	mdio-bus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		reset-gpios = <&gpio K1_GPIO(115) GPIO_ACTIVE_LOW>;
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <100000>;
+
+		rgmii1: phy@1 {
+			reg = <0x1>;
+		};
+	};
+};
+
+&pdma {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_2_cfg>;
+	status = "okay";
+};

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv