Re: [PATCH v12 04/12] mfd: zx297520v3: Add a clock and reset MFD driver

[Lee Jones <lee@kernel.org>]

On Wed, 23 Sep 2026, Stefan Dösinger wrote:

> This driver registers child devices for the zx297520v3 clock and reset
> controllers. The clk-zx297520v3 and reset-zte-zx297520v3 submitted in
> the next patches will drive the respective functionalities.
> 
> Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
> 
> ---
> 
> Changes v12:
> Added comments elaborating on the role of the driver and the hardware.
> 
> Regarding the names: zx297520v3 is the SoC's name (chip marking, boot
> messages). TOPCRM, MATRIXCRM, LSPCRM are ZTE's names for the MMIO blocks
> in their downstream sources. Sadly no datasheet is available. "clk",
> "reset" names for the child nodes are mine.
> 
> Regarding personal copyright: I am not affiliated with ZTE nor paid by
> them. This is my personal hobby project. I am using knowledge extracted
> from ZTE's kernel dumps, but not code.
> 
> Changes v10 (All Lee Jones):
> *) drop "select REGMAP_MMIO"
> *) Drop comment about unimplemented hwlocks
> *) Use MFD_CELL_[NAME|OF]
> *) Renamed the device type enum and its values
> *) Use device_get_match_data instead of the of_ variant
> *) Improved debug messages
> 
> Changes v9:
> Deassert the LSP reset and enable the LSP pclk here. In practice the
> boot rom needs to do that because it prints to an LSP-connected UART and
> reads the boot policy from the LSP connected flash chip.
> 
> In doing so, I migrated the match data to an enum as mfd.md suggests.
> 
> Changes v8:
> *) Remove .of_compatible from PHY mfd child
> 
> *) Move to drivers/mfd (Sashiko)
> 
> For me either soc/zte or mfd/ is fine. Note though that this MFD parent
> is very specific to the zx297520v3 SoC. I don't expect this to be reused
> anywhere else. There are two more MFD-ish devices in there: soc_sys at
> 0x140000, which I plan to handle in the same driver, and an i2c PMIC,
> which would get its own host driver.
> 
> *) Use PLATFORM_DEVID_AUTO (Sashiko). NONE was intentional as I only
> ever expect one instance, but I don't see any harm in doing the standard
> thing and use AUTO
> 
> *) On the suggestion not to put the link to mfd_cells[] into match data:
> I see that it is spelled out in Sashiko's mfd.md, written by Lee Jones,
> the MFD maintainer. I would appreciate some education on the rationale
> behind it: Putting a pointer into the void *data is a common pattern in
> the kernel. I don't understand in which situation this can possibly
> break?
> 
> Both structs are static const in the same compilation unit. data is a
> const void *, not a uintptr_t or kernel_ulong_t, so it seems passing a
> pointer is the intended use. What am I missing?
> 
> Changes v7:
> Add phy MFD child
> 
> Changes v6: Make the ZTE SoC driver section depend on HAS_IOMEM
> (Sashiko). The entire MFD section, which contains MFD_CORE, depends on
> HAS_IOMEM even with COMPILE_TEST.
> 
> Add a NULL ptr check for of_device_get_match_data (Sashiko). While not
> uniform, rave-sp, rohm-bd9576, atc260x, da9052-i2c protect against
> incorrect manual attachment that way.
> 
> Add lspclk here as well in an attempt to satisfy both Conor Dooley, who
> asks for MFD for top and matrix, and Philipp Zabel, who prefers aux but
> at least wants the reset driver limited to one driver type.
> 
> Changes v5: Use MFD instead of Aux bus for top and matrix crm because of
> extra functionality: Reboot in top, hwlock in Matrix.
> 
> LSP clocks stay with the aux bus and are thus not handled in this
> driver. The clk driver will bind directly to the lspcrm node.
> ---
>  MAINTAINERS                      |   1 +
>  drivers/mfd/Kconfig              |  12 +++++
>  drivers/mfd/Makefile             |   2 +
>  drivers/mfd/zte-zx297520v3-crm.c | 111 +++++++++++++++++++++++++++++++++++++++
>  4 files changed, 126 insertions(+)

Doesn't apply.

Please bring the MAINTAINERS changes out into their own patch

-- 
Lee Jones

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy