[PATCH v5 2/5] riscv: dts: spacemit: k3: add USB3 B and C controllers for Pico-ITX board

[Aurelien Jarno <aurelien@aurel32.net>]

The SpacemiT K3 has 4 USB3 controllers labelled A to D.

On the K3 Pico-ITX board, the controllers B and C are used in USB2 mode
only respectively for the M.2 B-Key slot and for the RTL8852BE Bluetooth
controller.

Add the two controller nodes. On the K3 Pico-ITX board, enable the
controllers nodes and add the two corresponding USB2 PHY nodes.

Tested-by: Anirudh Srinivasan <asrinivasan@oss.tenstorrent.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
---
 arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 22 +++++++
 arch/riscv/boot/dts/spacemit/k3.dtsi         | 60 ++++++++++++++++++++
 2 files changed, 82 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
index 0a6f669d509a9..5aa6fa89cab58 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
@@ -323,6 +323,28 @@ &usb2_phy {
 	status = "okay";
 };
 
+&usb3b {
+	phys = <&usb3b_u2phy>;
+	phy-names = "usb2-phy";
+	maximum-speed = "high-speed";
+	status = "okay";
+};
+
+&usb3b_u2phy {
+	status = "okay";
+};
+
+&usb3c {
+	phys = <&usb3c_u2phy>;
+	phy-names = "usb2-phy";
+	maximum-speed = "high-speed";
+	status = "okay";
+};
+
+&usb3c_u2phy {
+	status = "okay";
+};
+
 &usb3d_u2phy {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
index 1af47b7f1c8af..cf1c8b572c86b 100644
--- a/arch/riscv/boot/dts/spacemit/k3.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
@@ -441,6 +441,66 @@ soc: soc {
 		dma-noncoherent;
 		ranges;
 
+		usb3b: usb@81400000 {
+			compatible = "spacemit,k3-dwc3";
+			reg = <0x0 0x81400000 0x0 0x10000>;
+			interrupts = <125 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&saplic>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTB_BUS>;
+			clock-names = "usbdrd30";
+			resets = <&syscon_apmu RESET_APMU_USB3_B_AHB>,
+				 <&syscon_apmu RESET_APMU_USB3_B_VCC>,
+				 <&syscon_apmu RESET_APMU_USB3_B_PHY>;
+			reset-names = "ahb", "vcc", "phy";
+			phy_type = "utmi";
+			snps,dis_enblslpm_quirk;
+			snps,dis_u2_susphy_quirk;
+			snps,dis_u3_susphy_quirk;
+			snps,dis-del-phy-power-chg-quirk;
+			snps,dis-tx-ipgap-linecheck-quirk;
+			snps,parkmode-disable-ss-quirk;
+			dr_mode = "host";
+			status = "disabled";
+		};
+
+		usb3b_u2phy: phy@81500000 {
+			compatible = "spacemit,k3-usb2-phy";
+			reg = <0x0 0x81500000 0x0 0x200>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTB_BUS>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		usb3c: usb@81700000 {
+			compatible = "spacemit,k3-dwc3";
+			reg = <0x0 0x81700000 0x0 0x10000>;
+			interrupts = <148 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&saplic>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTC_BUS>;
+			clock-names = "usbdrd30";
+			resets = <&syscon_apmu RESET_APMU_USB3_C_AHB>,
+				 <&syscon_apmu RESET_APMU_USB3_C_VCC>,
+				 <&syscon_apmu RESET_APMU_USB3_C_PHY>;
+			reset-names = "ahb", "vcc", "phy";
+			phy_type = "utmi";
+			snps,dis_enblslpm_quirk;
+			snps,dis_u2_susphy_quirk;
+			snps,dis_u3_susphy_quirk;
+			snps,dis-del-phy-power-chg-quirk;
+			snps,dis-tx-ipgap-linecheck-quirk;
+			snps,parkmode-disable-ss-quirk;
+			dr_mode = "host";
+			status = "disabled";
+		};
+
+		usb3c_u2phy: phy@81800000 {
+			compatible = "spacemit,k3-usb2-phy";
+			reg = <0x0 0x81800000 0x0 0x200>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTC_BUS>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		usb3d: usb@81a00000 {
 			compatible = "spacemit,k3-dwc3";
 			reg = <0x0 0x81a00000 0x0 0x10000>;
-- 
2.53.0