From: Zi-Yu Chen <zychennvt@gmail.com>
To: rafael@kernel.org, daniel.lezcano@kernel.org
Cc: ychuang3@nuvoton.com, schung@nuvoton.com, p.zabel@pengutronix.de,
robh@kernel.org, krzk+dt@kernel.org, conor+dt@kernel.org,
rui.zhang@intel.com, lukasz.luba@arm.com,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-pm@vger.kernel.org, linux-kernel@vger.kernel.org,
Zi-Yu Chen <zychennvt@gmail.com>
Subject: [PATCH 3/4] thermal/drivers/ma35d1: Add Nuvoton MA35D1 thermal sensor driver
Date: Tue, 17 Nov 2026 14:05:00 +0800 [thread overview]
Message-ID: <20261117060501.2611071-4-zychennvt@gmail.com> (raw)
In-Reply-To: <20261117060501.2611071-1-zychennvt@gmail.com>
Add a driver for the on-chip temperature sensor of the Nuvoton MA35D1
SoC. The sensor is controlled through a register in the system
management (SYS) block and is instantiated as an auxiliary device by
the MA35D1 reset driver.
The sensor converts continuously while powered on. The 12-bit result
is converted to millidegrees Celsius using a linear fit of the
temperature table from the sensor datasheet.
Signed-off-by: Zi-Yu Chen <zychennvt@gmail.com>
---
drivers/thermal/Kconfig | 11 +++
drivers/thermal/Makefile | 1 +
drivers/thermal/ma35d1_thermal.c | 149 +++++++++++++++++++++++++++++++
3 files changed, 161 insertions(+)
create mode 100644 drivers/thermal/ma35d1_thermal.c
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 810eeccedfba..571b2c026311 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -530,4 +530,15 @@ config LOONGSON2_THERMAL
is higher than the high temperature threshold or lower than the low
temperature threshold, the interrupt will occur.
+config MA35D1_THERMAL
+ tristate "Nuvoton MA35D1 thermal sensor"
+ depends on RESET_NUVOTON_MA35D1
+ depends on THERMAL_OF
+ select MFD_SYSCON
+ help
+ Support for the on-chip temperature sensor found on Nuvoton
+ MA35D1 SoCs. The driver provides temperature readings through the
+ Linux thermal framework. The sensor registers are accessed through
+ the system register block.
+
endif
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 3b249195c088..bf2796e3dd3f 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -70,3 +70,4 @@ obj-$(CONFIG_SPRD_THERMAL) += sprd_thermal.o
obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL) += khadas_mcu_fan.o
obj-$(CONFIG_LOONGSON2_THERMAL) += loongson2_thermal.o
obj-$(CONFIG_THERMAL_CORE_TESTING) += testing/
+obj-$(CONFIG_MA35D1_THERMAL) += ma35d1_thermal.o
diff --git a/drivers/thermal/ma35d1_thermal.c b/drivers/thermal/ma35d1_thermal.c
new file mode 100644
index 000000000000..453f57d236ec
--- /dev/null
+++ b/drivers/thermal/ma35d1_thermal.c
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2026 Nuvoton Technology Corp.
+ *
+ * Author: Zi-Yu Chen <zychennvt@gmail.com>
+ */
+
+#include <linux/auxiliary_bus.h>
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/thermal.h>
+
+#include "thermal_hwmon.h"
+
+#define MA35_SYS_TSENSRFCR 0x104
+#define MA35_TSEN_DATA_VALID BIT(31)
+#define MA35_TSEN_POWER_DOWN BIT(28)
+#define MA35_TSEN_DATA GENMASK(27, 16)
+
+/*
+ * Conversion from the 12-bit sensor data to millidegrees Celsius:
+ * temp (mC) = data * MA35_TS_CAL_A / 4096 - MA35_TS_CAL_B
+ * A and B come from a linear fit of the S40LLV33_TEMPSENSOR temperature table.
+ */
+#define MA35_TS_CAL_A 274350
+#define MA35_TS_CAL_B 93330
+
+struct ma35d1_thermal {
+ struct device *dev;
+ struct regmap *regmap;
+};
+
+static int ma35d1_thermal_get_temp(struct thermal_zone_device *tzd, int *temp)
+{
+ struct ma35d1_thermal *sensor = thermal_zone_device_priv(tzd);
+ unsigned int reg;
+ int data, ret;
+
+ ret = regmap_read(sensor->regmap, MA35_SYS_TSENSRFCR, ®);
+ if (ret)
+ return ret;
+
+ if (!(reg & MA35_TSEN_DATA_VALID))
+ return -EAGAIN;
+
+ data = FIELD_GET(MA35_TSEN_DATA, reg);
+ *temp = data * MA35_TS_CAL_A / 4096 - MA35_TS_CAL_B;
+
+ return 0;
+}
+
+static int ma35d1_thermal_power_on(struct ma35d1_thermal *sensor)
+{
+ return regmap_clear_bits(sensor->regmap, MA35_SYS_TSENSRFCR,
+ MA35_TSEN_POWER_DOWN);
+}
+
+static int ma35d1_thermal_power_off(struct ma35d1_thermal *sensor)
+{
+ return regmap_set_bits(sensor->regmap, MA35_SYS_TSENSRFCR,
+ MA35_TSEN_POWER_DOWN);
+}
+
+static int ma35d1_thermal_change_mode(struct thermal_zone_device *tzd,
+ enum thermal_device_mode mode)
+{
+ struct ma35d1_thermal *sensor = thermal_zone_device_priv(tzd);
+
+ if (mode == THERMAL_DEVICE_ENABLED)
+ return ma35d1_thermal_power_on(sensor);
+
+ return ma35d1_thermal_power_off(sensor);
+}
+
+static void ma35d1_thermal_power_off_action(void *data)
+{
+ struct ma35d1_thermal *sensor = data;
+
+ if (ma35d1_thermal_power_off(sensor))
+ dev_warn(sensor->dev, "failed to power off sensor\n");
+}
+
+static const struct thermal_zone_device_ops ma35d1_tz_ops = {
+ .get_temp = ma35d1_thermal_get_temp,
+ .change_mode = ma35d1_thermal_change_mode,
+};
+
+static int ma35d1_thermal_probe(struct auxiliary_device *adev,
+ const struct auxiliary_device_id *id)
+{
+ struct device *dev = &adev->dev;
+ struct thermal_zone_device *tzd;
+ struct ma35d1_thermal *sensor;
+ int ret;
+
+ sensor = devm_kzalloc_obj(dev, *sensor);
+ if (!sensor)
+ return -ENOMEM;
+
+ sensor->dev = dev;
+
+ sensor->regmap = syscon_node_to_regmap(dev->parent->of_node);
+ if (IS_ERR(sensor->regmap))
+ return dev_err_probe(dev, PTR_ERR(sensor->regmap),
+ "failed to get SYS regmap\n");
+
+ /*
+ * Registered before the thermal zone so that the sensor is powered
+ * off only after the zone has been unregistered.
+ */
+ ret = devm_add_action_or_reset(dev, ma35d1_thermal_power_off_action,
+ sensor);
+ if (ret)
+ return ret;
+
+ tzd = devm_thermal_of_zone_register(dev, 0, sensor, &ma35d1_tz_ops);
+ if (IS_ERR(tzd))
+ return dev_err_probe(dev, PTR_ERR(tzd),
+ "failed to register thermal zone\n");
+
+ /* thermal_of disables hwmon by default */
+ ret = devm_thermal_add_hwmon_sysfs(dev, tzd);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to add hwmon sysfs\n");
+
+ return 0;
+}
+
+static const struct auxiliary_device_id ma35d1_thermal_id_table[] = {
+ { .name = "reset_ma35d1.thermal" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(auxiliary, ma35d1_thermal_id_table);
+
+static struct auxiliary_driver ma35d1_thermal_driver = {
+ .probe = ma35d1_thermal_probe,
+ .id_table = ma35d1_thermal_id_table,
+};
+module_auxiliary_driver(ma35d1_thermal_driver);
+
+MODULE_AUTHOR("Zi-Yu Chen <zychennvt@gmail.com>");
+MODULE_DESCRIPTION("Nuvoton MA35D1 Temperature Sensor Driver");
+MODULE_LICENSE("GPL");
--
2.34.1
next prev parent reply other threads:[~2026-11-17 6:06 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-17 6:04 [PATCH 0/4] Add Nuvoton MA35D1 thermal sensor support Zi-Yu Chen
2026-11-17 6:04 ` [PATCH 1/4] dt-bindings: reset: nuvoton,ma35d1-reset: Add #thermal-sensor-cells Zi-Yu Chen
2026-11-17 6:04 ` [PATCH 2/4] reset: ma35d1: Register auxiliary device for the temperature sensor Zi-Yu Chen
2026-11-17 6:05 ` Zi-Yu Chen [this message]
2026-11-17 6:23 ` [PATCH 3/4] thermal/drivers/ma35d1: Add Nuvoton MA35D1 thermal sensor driver sashiko-bot
2026-11-17 14:16 ` Uwe Kleine-König
2026-11-18 0:46 ` zychen
2026-11-17 6:05 ` [PATCH 4/4] arm64: dts: nuvoton: ma35d1: Add thermal zone Zi-Yu Chen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261117060501.2611071-4-zychennvt@gmail.com \
--to=zychennvt@gmail.com \
--cc=conor+dt@kernel.org \
--cc=daniel.lezcano@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=lukasz.luba@arm.com \
--cc=p.zabel@pengutronix.de \
--cc=rafael@kernel.org \
--cc=robh@kernel.org \
--cc=rui.zhang@intel.com \
--cc=schung@nuvoton.com \
--cc=ychuang3@nuvoton.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.