All of lore.kernel.org
 help / color / mirror / Atom feed
* Sym53c8xx in 2.3.now
@ 1999-09-01 15:16 Geert Uytterhoeven
  1999-09-01 20:35 ` D. Lance Robinson
  1999-09-05 21:12 ` vger on LongTrail (was: Re: Sym53c8xx in 2.3.now) Geert Uytterhoeven
  0 siblings, 2 replies; 4+ messages in thread
From: Geert Uytterhoeven @ 1999-09-01 15:16 UTC (permalink / raw)
  To: Linux/PPC Development



Anybody who has the sym53c8xx or ncr53c8xx driver working with the latest 2.3.x kernels?

I get:

| sym53c8xx: at PCI bus 0, device 6, function 0
| sym53c8xx: setting PCI_COMMAND_IO PCI_COMMAND_MEMORY...
| sym53c8xx: setting PCI_COMMAND_MASTER PCI_COMMAND_PARITY...(fix-up)
| sym53c8xx: 53c875 detected 
| sym53c875-0: rev=0x04, base=0xc3000000, io_port=0x1400, irq=31
| sym53c875-0: NCR clock is 40218KHz, 40218KHz
| sym53c875-0: ID 7, Fast-20, Parity Checking
| sym53c875-0: on-chip RAM at 0xc3001000
| sym53c875-0: restart (scsi reset).
| sym53c875-0: Downloading SCSI SCRIPTS.
| ncr53c8xx: at PCI bus 0, device 6, function 0
| ncr53c8xx: IO region 0x1400 to 0x147f is in use
| mesh: assuming 50MHz clock frequency
| scsi0 : sym53c8xx - version 1.3c
| scsi1 : MESH
| scsi : 2 hosts.
| scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 
| sym53c8xx_abort: pid=0 serial_number=1 serial_number_at_timeout=1

And then the system hangs in a wait loop...

My devices (from 2.3.6 dmesg):

|   Vendor: QUANTUM   Model: VIKING II 4.5WLS  Rev: 3506
|   Type:   Direct-Access                      ANSI SCSI revision: 02
| Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
|   Vendor: PLEXTOR   Model: CD-ROM PX-12TS    Rev: 1.02
|   Type:   CD-ROM                             ANSI SCSI revision: 02
|   Vendor: HP        Model: HP35480A          Rev: T503
|   Type:   Sequential-Access                  ANSI SCSI revision: 02
| sym53c875-0-<0,0>: tagged command queue depth set to 8
|   Vendor: QUANTUM   Model: FIREBALL_TM3200S  Rev: 300X
|   Type:   Direct-Access                      ANSI SCSI revision: 02
| Detected scsi disk sdb at scsi1, channel 0, id 5, lun 0
| scsi : detected 2 SCSI disks total.
| sym53c875-0-<0,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
| SCSI device sda: hdwr sector= 512 bytes. Sectors= 8910423 [4350 MB] [4.4 GB]
| SCSI device sdb: hdwr sector= 512 bytes. Sectors= 6281856 [3067 MB] [3.1 GB]

Disabling sym53c8xx and using ncr53c8xx instead doesn't fix the problem.

Greetings,

						Geert

--
Geert Uytterhoeven                   Geert.Uytterhoeven@sonycom.com
Sony Suprastructure Center Europe (SUPC-E) --- Brussels --- Belgium


[[ This message was sent via the linuxppc-dev mailing list.  Replies are ]]
[[ not  forced  back  to the list, so be sure to Cc linuxppc-dev if your ]]
[[ reply is of general interest. Please check http://lists.linuxppc.org/ ]]
[[ and http://www.linuxppc.org/ for useful information before posting.   ]]

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: Sym53c8xx in 2.3.now
  1999-09-01 15:16 Sym53c8xx in 2.3.now Geert Uytterhoeven
@ 1999-09-01 20:35 ` D. Lance Robinson
  1999-09-01 22:00   ` Geert Uytterhoeven
  1999-09-05 21:12 ` vger on LongTrail (was: Re: Sym53c8xx in 2.3.now) Geert Uytterhoeven
  1 sibling, 1 reply; 4+ messages in thread
From: D. Lance Robinson @ 1999-09-01 20:35 UTC (permalink / raw)
  To: Geert Uytterhoeven; +Cc: Linux/PPC Development


Geert,

You should post your message on the linux-scsi list server. Gerard, who
wrote the driver listens in on that list.

  send to linux-scsi@vger.rutgers.edu

<>< Lance.



Geert Uytterhoeven wrote:
> 
> Anybody who has the sym53c8xx or ncr53c8xx driver working with the latest 2.3.x kernels?
> 
> I get:
> 
> | sym53c8xx: at PCI bus 0, device 6, function 0
> | sym53c8xx: setting PCI_COMMAND_IO PCI_COMMAND_MEMORY...
> | sym53c8xx: setting PCI_COMMAND_MASTER PCI_COMMAND_PARITY...(fix-up)
> | sym53c8xx: 53c875 detected
> | sym53c875-0: rev=0x04, base=0xc3000000, io_port=0x1400, irq=31
> | sym53c875-0: NCR clock is 40218KHz, 40218KHz
> | sym53c875-0: ID 7, Fast-20, Parity Checking
> | sym53c875-0: on-chip RAM at 0xc3001000
> | sym53c875-0: restart (scsi reset).
> | sym53c875-0: Downloading SCSI SCRIPTS.
> | ncr53c8xx: at PCI bus 0, device 6, function 0
> | ncr53c8xx: IO region 0x1400 to 0x147f is in use
> | mesh: assuming 50MHz clock frequency
> | scsi0 : sym53c8xx - version 1.3c
> | scsi1 : MESH
> | scsi : 2 hosts.
> | scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00
> | sym53c8xx_abort: pid=0 serial_number=1 serial_number_at_timeout=1
> 
> And then the system hangs in a wait loop...
> 
> My devices (from 2.3.6 dmesg):
> 
> |   Vendor: QUANTUM   Model: VIKING II 4.5WLS  Rev: 3506
> |   Type:   Direct-Access                      ANSI SCSI revision: 02
> | Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
> |   Vendor: PLEXTOR   Model: CD-ROM PX-12TS    Rev: 1.02
> |   Type:   CD-ROM                             ANSI SCSI revision: 02
> |   Vendor: HP        Model: HP35480A          Rev: T503
> |   Type:   Sequential-Access                  ANSI SCSI revision: 02
> | sym53c875-0-<0,0>: tagged command queue depth set to 8
> |   Vendor: QUANTUM   Model: FIREBALL_TM3200S  Rev: 300X
> |   Type:   Direct-Access                      ANSI SCSI revision: 02
> | Detected scsi disk sdb at scsi1, channel 0, id 5, lun 0
> | scsi : detected 2 SCSI disks total.
> | sym53c875-0-<0,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
> | SCSI device sda: hdwr sector= 512 bytes. Sectors= 8910423 [4350 MB] [4.4 GB]
> | SCSI device sdb: hdwr sector= 512 bytes. Sectors= 6281856 [3067 MB] [3.1 GB]
> 
> Disabling sym53c8xx and using ncr53c8xx instead doesn't fix the problem.
> 
> Greetings,
> 
>                                                 Geert
> 
> --
> Geert Uytterhoeven                   Geert.Uytterhoeven@sonycom.com
> Sony Suprastructure Center Europe (SUPC-E) --- Brussels --- Belgium

[[ This message was sent via the linuxppc-dev mailing list.  Replies are ]]
[[ not  forced  back  to the list, so be sure to Cc linuxppc-dev if your ]]
[[ reply is of general interest. Please check http://lists.linuxppc.org/ ]]
[[ and http://www.linuxppc.org/ for useful information before posting.   ]]

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: Sym53c8xx in 2.3.now
  1999-09-01 20:35 ` D. Lance Robinson
@ 1999-09-01 22:00   ` Geert Uytterhoeven
  0 siblings, 0 replies; 4+ messages in thread
From: Geert Uytterhoeven @ 1999-09-01 22:00 UTC (permalink / raw)
  To: D. Lance Robinson; +Cc: Linux/PPC Development


On Wed, 1 Sep 1999, D. Lance Robinson wrote:
> You should post your message on the linux-scsi list server. Gerard, who
> wrote the driver listens in on that list.
> 
>   send to linux-scsi@vger.rutgers.edu

I already did more than a week ago. No response.

Greetings,

						Geert

--
Geert Uytterhoeven                   Geert.Uytterhoeven@sonycom.com
Sony Suprastructure Center Europe (SUPC-E) --- Brussels --- Belgium


[[ This message was sent via the linuxppc-dev mailing list.  Replies are ]]
[[ not  forced  back  to the list, so be sure to Cc linuxppc-dev if your ]]
[[ reply is of general interest. Please check http://lists.linuxppc.org/ ]]
[[ and http://www.linuxppc.org/ for useful information before posting.   ]]

^ permalink raw reply	[flat|nested] 4+ messages in thread

* vger on LongTrail (was: Re: Sym53c8xx in 2.3.now)
  1999-09-01 15:16 Sym53c8xx in 2.3.now Geert Uytterhoeven
  1999-09-01 20:35 ` D. Lance Robinson
@ 1999-09-05 21:12 ` Geert Uytterhoeven
  1 sibling, 0 replies; 4+ messages in thread
From: Geert Uytterhoeven @ 1999-09-05 21:12 UTC (permalink / raw)
  To: Linux/PPC Development


On Wed, 1 Sep 1999, Geert Uytterhoeven wrote:
> Anybody who has the sym53c8xx or ncr53c8xx driver working with the latest 2.3.x kernels?
> 
> I get:
> 
> | sym53c8xx: at PCI bus 0, device 6, function 0
> | sym53c8xx: setting PCI_COMMAND_IO PCI_COMMAND_MEMORY...
> | sym53c8xx: setting PCI_COMMAND_MASTER PCI_COMMAND_PARITY...(fix-up)
> | sym53c8xx: 53c875 detected 
> | sym53c875-0: rev=0x04, base=0xc3000000, io_port=0x1400, irq=31
> | sym53c875-0: NCR clock is 40218KHz, 40218KHz
> | sym53c875-0: ID 7, Fast-20, Parity Checking
> | sym53c875-0: on-chip RAM at 0xc3001000
> | sym53c875-0: restart (scsi reset).
> | sym53c875-0: Downloading SCSI SCRIPTS.
> | ncr53c8xx: at PCI bus 0, device 6, function 0
> | ncr53c8xx: IO region 0x1400 to 0x147f is in use
> | mesh: assuming 50MHz clock frequency
> | scsi0 : sym53c8xx - version 1.3c
> | scsi1 : MESH
> | scsi : 2 hosts.
> | scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 
> | sym53c8xx_abort: pid=0 serial_number=1 serial_number_at_timeout=1
> 
> And then the system hangs in a wait loop...

I'm starting to think that the problem is related to interrupts. I also get one
or two messages `Keyboard timeout[2]', and the keyboard (PS/2) doesn't seem to
work (Caps Lock doesn't toggle the Caps Lock LED).

Besides, things are getting worse. For the current vger kernel, I needed this
patch to make it compile:

Index: include/asm-ppc/serial.h
===================================================================
RCS file: /vger/u4/cvs/linux/include/asm-ppc/serial.h,v
retrieving revision 1.7
diff -u -r1.7 serial.h
--- serial.h	1999/09/02 21:23:49	1.7
+++ serial.h	1999/09/05 21:11:22
@@ -33,7 +33,6 @@
 #endif
 
 #else
-#define SERIAL_PORT_DFNS
 /*
  * PReP, CHRP, etc.
  */
@@ -52,6 +51,9 @@
 #define ACCENT_FLAGS 0
 #define BOCA_FLAGS 0
 #define HUB6_FLAGS 0
+#define RS_TABLE_SIZE	64
+#else
+#define RS_TABLE_SIZE	4
 #endif
 	
 /*

And now my serial console is scrambled after the serial port init :-(

Greetings,

						Geert

--
Geert Uytterhoeven                   Geert.Uytterhoeven@sonycom.com
Sony Suprastructure Center Europe (SUPC-E) --- Brussels --- Belgium


** Sent via the linuxppc-dev mail list. See http://lists.linuxppc.org/

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~1999-09-05 21:12 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
1999-09-01 15:16 Sym53c8xx in 2.3.now Geert Uytterhoeven
1999-09-01 20:35 ` D. Lance Robinson
1999-09-01 22:00   ` Geert Uytterhoeven
1999-09-05 21:12 ` vger on LongTrail (was: Re: Sym53c8xx in 2.3.now) Geert Uytterhoeven

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.