From: "K.R. Foley" <kr@cybsft.com>
To: James Bottomley <James.Bottomley@SteelEye.com>
Cc: dino@in.ibm.com, Andrew Morton <akpm@osdl.org>,
gregoire.favre@gmail.com,
Linux Kernel <linux-kernel@vger.kernel.org>,
SCSI Mailing List <linux-scsi@vger.kernel.org>
Subject: Re: What breaks aic7xxx in post 2.6.12-rc2 ?
Date: Thu, 19 May 2005 06:27:44 -0500 [thread overview]
Message-ID: <428C7830.5070302@cybsft.com> (raw)
In-Reply-To: <1116476630.5867.2.camel@mulgrave>
James Bottomley wrote:
> On Wed, 2005-05-18 at 22:07 -0500, K.R. Foley wrote:
>
>>This also solves my problem that I reported in this thread
>>http://marc.theaimsgroup.com/?l=linux-scsi&m=111422854418964&w=2
>
>
> OK, I think the patch below is the extract of this. Could you see if it
> works by simply patching vanilla 2.6.12-rc4 with no other SCSI patches
> (if it does, I'll push it for 2.6.12 final).
>
> James
<snip>
James,
Below is what I get WHEN IT BOOTS. There are also a couple more logs and
notes in between.
#########################################################################
May 19 06:04:22 porky kernel: scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI
HBA DRIVER, Rev 6.2.36
May 19 06:04:22 porky kernel: <Adaptec aic7899 Ultra160 SCSI
adapter>
May 19 06:04:22 porky kernel: aic7899: Ultra160 Wide Channel A,
SCSI Id=7, 32/253 SCBs
May 19 06:04:22 porky kernel:
May 19 06:04:22 porky kernel: Vendor: QUANTUM Model:
ATLAS10K2-TY092L Rev: DA40
May 19 06:04:22 porky kernel: Type: Direct-Access
ANSI SCSI revision: 03
May 19 06:04:22 porky kernel: scsi0:A:0:0: Tagged Queuing enabled. Depth 32
May 19 06:04:22 porky kernel: target0:0:0: Beginning Domain Validation
May 19 06:04:22 porky kernel: (scsi0:A:0): 6.600MB/s transfers (16bit)
May 19 06:04:22 porky kernel: (scsi0:A:0): 80.000MB/s transfers
(40.000MHz, offset 127, 16bit)
May 19 06:04:22 porky kernel: target0:0:0: Ending Domain Validation
May 19 06:04:22 porky kernel: scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI
HBA DRIVER, Rev 6.2.36
May 19 06:04:22 porky kernel: <Adaptec aic7899 Ultra160 SCSI
adapter>
May 19 06:04:22 porky kernel: aic7899: Ultra160 Wide Channel B,
SCSI Id=7, 32/253 SCBs
May 19 06:04:22 porky kernel:
May 19 06:04:22 porky kernel: Vendor: SEAGATE Model: SX118273LC
Rev: 6679
May 19 06:04:22 porky kernel: Type: Direct-Access
ANSI SCSI revision: 02
May 19 06:04:22 porky kernel: scsi1:A:0:0: Tagged Queuing enabled. Depth 32
May 19 06:04:22 porky kernel: target1:0:0: Beginning Domain Validation
May 19 06:04:22 porky kernel: (scsi1:A:0): 6.600MB/s transfers (16bit)
May 19 06:04:22 porky kernel: (scsi1:A:0:0): parity error detected in
Data-in phase. SEQADDR(0x1a6) SCSIRATE(0x80)
May 19 06:04:22 porky kernel: (scsi1:A:0:0): parity error detected in
Message-in phase. SEQADDR(0x1a6) SCSIRATE(0x80)
May 19 06:04:22 porky kernel: (scsi1:A:0:0): Unexpected busfree in
Message-out phase
May 19 06:04:22 porky kernel: SEQADDR == 0x16b
May 19 06:04:22 porky kernel: target1:0:0: Wide Transfers Fail
May 19 06:04:22 porky kernel: (scsi1:A:0): 3.300MB/s transfers
May 19 06:04:22 porky kernel: target1:0:0: Domain Validation skipping
write tests
May 19 06:04:22 porky kernel: (scsi1:A:0): 20.000MB/s transfers
(20.000MHz, offset 15)
May 19 06:04:22 porky kernel: target1:0:0: Ending Domain Validation
May 19 06:04:22 porky kernel: SCSI device sda: 17783239 512-byte hdwr
sectors (9105 MB)
May 19 06:04:22 porky kernel: SCSI device sda: drive cache: write back
May 19 06:04:22 porky kernel: SCSI device sda: 17783239 512-byte hdwr
sectors (9105 MB)
May 19 06:04:22 porky kernel: SCSI device sda: drive cache: write back
May 19 06:04:22 porky kernel: sda: sda1 sda2 sda3
May 19 06:04:22 porky kernel: Attached scsi disk sda at scsi0, channel
0, id 0, lun 0
May 19 06:04:22 porky kernel: SCSI device sdb: 35566480 512-byte hdwr
sectors (18210 MB)
May 19 06:04:22 porky kernel: SCSI device sdb: drive cache: write through
May 19 06:04:22 porky kernel: SCSI device sdb: 35566480 512-byte hdwr
sectors (18210 MB)
May 19 06:04:22 porky kernel: SCSI device sdb: drive cache: write through
May 19 01:04:03 porky rc.sysinit: -e
May 19 06:04:22 porky kernel: sdb: sdb1
May 19 01:04:04 porky udevsend[1251]: starting udevd daemon
May 19 06:04:22 porky kernel: Attached scsi disk sdb at scsi1, channel
0, id 0, lun 0
May 19 01:04:05 porky scsi.agent[1263]: disk at
/devices/pci0000:00/0000:00:1e.0/0000:04:05.0/host0/target0:0:0/0:0:0:0
May 19 06:04:23 porky kernel: Attached scsi generic sg0 at scsi0,
channel 0, id 0, lun 0, type 0
May 19 01:04:05 porky scsi.agent[1288]: disk at
/devices/pci0000:00/0000:00:1e.0/0000:04:05.1/host1/target1:0:0/1:0:0:0
May 19 06:04:23 porky kernel: Attached scsi generic sg1 at scsi1,
channel 0, id 0, lun 0, type 0
###############################################################################
Even with the patch that you posted last night something still isn't
quite right. Notice in the output below that the faster drive is setup
at 80MB/s instead of 160MB/s. It's like going back to the days before
U160 stuff worked properly :)
###############################################################################
May 18 21:56:25 porky kernel: scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI
HBA DRIVER, Rev 6.2.36
May 18 21:56:25 porky kernel: <Adaptec aic7899 Ultra160 SCSI
adapter>
May 18 21:56:25 porky kernel: aic7899: Ultra160 Wide Channel A,
SCSI Id=7, 32/253 SCBs
May 18 21:56:25 porky kernel:
May 18 21:56:25 porky kernel: Vendor: QUANTUM Model:
ATLAS10K2-TY092L Rev: DA40
May 18 21:56:25 porky kernel: Type: Direct-Access
ANSI SCSI revision: 03
May 18 21:56:25 porky kernel: scsi0:A:0:0: Tagged Queuing enabled. Depth 32
May 18 21:56:25 porky kernel: target0:0:0: Beginning Domain Validation
May 18 21:56:25 porky kernel: WIDTH IS 1
May 18 21:56:25 porky kernel: (scsi0:A:0): 6.600MB/s transfers (16bit)
May 18 21:56:25 porky kernel: (scsi0:A:0): 80.000MB/s transfers
(40.000MHz, offset 127, 16bit)
May 18 21:56:25 porky kernel: target0:0:0: Ending Domain Validation
May 18 21:56:25 porky kernel: scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI
HBA DRIVER, Rev 6.2.36
May 18 21:56:25 porky kernel: <Adaptec aic7899 Ultra160 SCSI
adapter>
May 18 21:56:25 porky kernel: aic7899: Ultra160 Wide Channel B,
SCSI Id=7, 32/253 SCBs
May 18 21:56:25 porky kernel:
May 18 21:56:25 porky kernel: Vendor: SEAGATE Model: SX118273LC
Rev: 6679
May 18 21:56:25 porky kernel: Type: Direct-Access
ANSI SCSI revision: 02
May 18 21:56:25 porky kernel: scsi1:A:0:0: Tagged Queuing enabled. Depth 32
May 18 21:56:25 porky kernel: target1:0:0: Beginning Domain Validation
May 18 21:56:25 porky kernel: target1:0:0: Domain Validation skipping
write tests
May 18 21:56:25 porky kernel: (scsi1:A:0): 20.000MB/s transfers
(20.000MHz, offset 15)
May 18 21:56:25 porky kernel: target1:0:0: Ending Domain Validation
May 18 21:56:25 porky kernel: SCSI device sda: 17783239 512-byte hdwr
sectors (9105 MB)
May 18 21:56:25 porky kernel: SCSI device sda: drive cache: write back
May 18 21:56:25 porky kernel: SCSI device sda: 17783239 512-byte hdwr
sectors (9105 MB)
May 18 21:56:25 porky kernel: SCSI device sda: drive cache: write back
May 18 21:56:25 porky kernel: sda: sda1 sda2 sda3
May 18 21:56:25 porky kernel: Attached scsi disk sda at scsi0, channel
0, id 0, lun 0
May 18 21:56:25 porky kernel: SCSI device sdb: 35566480 512-byte hdwr
sectors (18210 MB)
May 18 21:56:25 porky kernel: SCSI device sdb: drive cache: write through
May 18 16:56:04 porky rc.sysinit: -e
May 18 21:56:25 porky kernel: SCSI device sdb: 35566480 512-byte hdwr
sectors (18210 MB)
May 18 16:56:06 porky udevsend[1281]: starting udevd daemon
May 18 21:56:25 porky kernel: SCSI device sdb: drive cache: write through
May 18 16:56:06 porky scsi.agent[1293]: disk at
/devices/pci0000:00/0000:00:1e.0/0000:04:05.0/host0/target0:0:0/0:0:0:0
May 18 21:56:25 porky kernel: sdb: sdb1
May 18 16:56:06 porky scsi.agent[1318]: disk at
/devices/pci0000:00/0000:00:1e.0/0000:04:05.1/host1/target1:0:0/1:0:0:0
May 18 21:56:25 porky kernel: Attached scsi disk sdb at scsi1, channel
0, id 0, lun 0
May 18 16:56:06 porky udevsend[1334]: starting udevd daemon
May 18 21:56:25 porky kernel: Attached scsi generic sg0 at scsi0,
channel 0, id 0, lun 0, type 0
May 18 16:56:11 porky start_udev: Starting udev: succeeded
May 18 21:56:25 porky kernel: Attached scsi generic sg1 at scsi1,
channel 0, id 0, lun 0, type 0
#################################################################################
And then finally the output this morning of booting 2.6.12-rc2 (with RT
patches applied, which is irrelevant to this conversation). This one
does properly setup all of the drives.
#################################################################################
May 19 05:52:00 porky kernel: scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI
HBA DRIVER, Rev 6.2.36
May 19 05:52:00 porky kernel: <Adaptec aic7899 Ultra160 SCSI
adapter>
May 19 05:52:00 porky kernel: aic7899: Ultra160 Wide Channel A,
SCSI Id=7, 32/253 SCBs
May 19 05:52:00 porky kernel:
May 19 05:52:00 porky kernel: (scsi0:A:0): 160.000MB/s transfers
(80.000MHz DT, offset 127, 16bit)
May 19 05:52:00 porky kernel: Vendor: QUANTUM Model:
ATLAS10K2-TY092L Rev: DA40
May 19 05:52:00 porky kernel: Type: Direct-Access
ANSI SCSI revision: 03
May 19 05:52:00 porky kernel: scsi0:A:0:0: Tagged Queuing enabled. Depth 32
May 19 05:52:00 porky kernel: scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI
HBA DRIVER, Rev 6.2.36
May 19 05:52:00 porky kernel: <Adaptec aic7899 Ultra160 SCSI
adapter>
May 19 05:52:00 porky kernel: aic7899: Ultra160 Wide Channel B,
SCSI Id=7, 32/253 SCBs
May 19 05:52:00 porky kernel:
May 19 05:52:00 porky kernel: (scsi1:A:0): 20.000MB/s transfers
(20.000MHz, offset 15)
May 19 05:52:00 porky kernel: Vendor: SEAGATE Model: SX118273LC
Rev: 6679
May 19 05:52:00 porky netfs: Mounting other filesystems: succeeded
May 19 05:52:00 porky kernel: Type: Direct-Access
ANSI SCSI revision: 02
May 19 05:52:00 porky kernel: scsi1:A:0:0: Tagged Queuing enabled. Depth 32
May 19 05:52:00 porky kernel: SCSI device sda: 17783239 512-byte hdwr
sectors (9105 MB)
May 19 05:52:00 porky kernel: SCSI device sda: drive cache: write back
May 19 05:52:00 porky kernel: SCSI device sda: 17783239 512-byte hdwr
sectors (9105 MB)
May 19 05:52:00 porky kernel: SCSI device sda: drive cache: write back
May 19 05:52:00 porky kernel: sda: sda1 sda2 sda3
May 19 05:52:00 porky kernel: Attached scsi disk sda at scsi0, channel
0, id 0, lun 0
--
kr
prev parent reply other threads:[~2005-05-19 11:27 UTC|newest]
Thread overview: 109+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-05-16 8:58 What breaks aic7xxx in post 2.6.12-rc2 ? Grégoire Favre
2005-05-16 15:03 ` Jesper Juhl
2005-05-16 15:12 ` What breaks aic7xxx in post 2.6.12-rc2 ? (on amd64 ?) Grégoire Favre
2005-05-16 15:31 ` Jesper Juhl
2005-05-17 7:13 ` What breaks aic7xxx in post 2.6.12-rc2 ? Dinakar Guniguntala
2005-05-17 7:29 ` Andrew Morton
2005-05-17 8:34 ` Dinakar Guniguntala
2005-05-26 7:39 ` Andrew Morton
2005-05-26 10:37 ` K.R. Foley
2005-05-26 10:50 ` Dinakar Guniguntala
2005-05-26 12:59 ` James Bottomley
2005-05-17 14:34 ` James Bottomley
2005-05-17 15:57 ` Grégoire Favre
2005-05-17 15:57 ` Grégoire Favre
2005-05-17 16:38 ` James Bottomley
2005-05-17 16:38 ` James Bottomley
2005-05-17 16:52 ` Grégoire Favre
2005-05-17 16:52 ` Grégoire Favre
2005-05-17 18:16 ` James Bottomley
2005-05-17 18:16 ` James Bottomley
2005-05-17 17:08 ` Dinakar Guniguntala
2005-05-17 18:34 ` James Bottomley
2005-05-17 19:26 ` Grégoire Favre
2005-05-17 19:26 ` Grégoire Favre
2005-05-17 19:50 ` James Bottomley
2005-05-17 19:50 ` James Bottomley
2005-05-17 19:56 ` Grégoire Favre
2005-05-17 19:56 ` Grégoire Favre
2005-05-17 21:06 ` James Bottomley
2005-05-17 21:06 ` James Bottomley
2005-05-17 22:09 ` Grégoire Favre
2005-05-17 22:14 ` James Bottomley
2005-05-17 22:14 ` James Bottomley
2005-05-21 23:22 ` Grégoire Favre
2005-05-21 23:22 ` Grégoire Favre
2005-05-22 13:54 ` James Bottomley
2005-05-22 13:54 ` James Bottomley
2005-05-24 15:39 ` Grégoire Favre
2005-05-24 15:39 ` Grégoire Favre
2005-05-26 13:19 ` James Bottomley
2005-05-26 13:19 ` James Bottomley
2005-05-26 14:35 ` Grégoire Favre
2005-05-26 14:35 ` Grégoire Favre
2005-05-26 14:46 ` James Bottomley
2005-05-26 17:35 ` Grégoire Favre
2005-05-26 17:35 ` Grégoire Favre
2005-05-30 14:38 ` James Bottomley
2005-05-30 14:38 ` James Bottomley
2005-05-30 14:51 ` Michael Tokarev
2005-05-30 14:59 ` James Bottomley
2005-05-30 15:09 ` Grégoire Favre
2005-05-30 15:09 ` Grégoire Favre
2005-05-30 15:34 ` James Bottomley
2005-05-30 15:34 ` James Bottomley
2005-05-30 16:01 ` Grégoire Favre
2005-05-30 16:01 ` Grégoire Favre
2005-05-30 18:17 ` James Bottomley
2005-05-30 18:17 ` James Bottomley
2005-05-30 19:07 ` Grégoire Favre
2005-05-30 19:07 ` Grégoire Favre
2005-06-06 18:17 ` James Bottomley
2005-06-06 18:17 ` James Bottomley
2005-06-07 8:57 ` Grégoire Favre
2005-06-07 8:57 ` Grégoire Favre
2005-06-12 15:38 ` James Bottomley
2005-06-12 15:38 ` James Bottomley
2005-06-13 14:50 ` Grégoire Favre
2005-06-13 14:50 ` Grégoire Favre
2005-06-13 14:59 ` James Bottomley
2005-06-13 15:05 ` Christoph Hellwig
2005-06-13 15:17 ` Grégoire Favre
2005-06-13 15:17 ` Grégoire Favre
2005-06-13 18:37 ` Gr�goire Favre
2005-06-13 18:37 ` Gr�goire Favre
2005-06-13 20:50 ` James Bottomley
2005-06-13 21:33 ` Gregoire Favre
2005-06-13 21:46 ` James Bottomley
2005-06-13 21:59 ` Gregoire Favre
2005-06-13 22:04 ` James Bottomley
2005-06-13 22:25 ` Gregoire Favre
2005-06-14 2:20 ` James Bottomley
2005-06-14 9:28 ` What breaks aic7xxx in post 2.6.12-rc2 ? (fixed in 2.6.12-rc6 with patches) Gregoire Favre
2005-06-13 21:42 ` What breaks aic7xxx in post 2.6.12-rc2 ? Frank van Maarseveen
2005-06-13 22:59 ` James Bottomley
2005-06-14 21:42 ` Frank van Maarseveen
2005-06-15 12:02 ` Frank van Maarseveen
2005-06-15 14:14 ` James Bottomley
2005-06-15 20:09 ` Frank van Maarseveen
2005-06-15 20:15 ` James Bottomley
2005-06-15 20:15 ` James Bottomley
2005-06-15 20:49 ` Frank van Maarseveen
2005-06-15 20:49 ` Frank van Maarseveen
2005-05-18 9:07 ` Dinakar Guniguntala
2005-05-18 14:12 ` James Bottomley
2005-05-18 14:40 ` Dinakar Guniguntala
2005-05-19 3:07 ` K.R. Foley
2005-05-19 4:23 ` James Bottomley
2005-05-19 9:51 ` Dinakar Guniguntala
2005-05-19 23:56 ` James Bottomley
2005-05-20 1:05 ` K.R. Foley
2005-05-20 1:17 ` James Bottomley
2005-05-20 1:32 ` K.R. Foley
2005-05-20 1:33 ` James Bottomley
2005-05-20 1:40 ` James Bottomley
2005-05-20 1:54 ` K.R. Foley
2005-05-20 2:30 ` James Bottomley
2005-05-20 3:06 ` K.R. Foley
2005-05-20 10:09 ` Dinakar Guniguntala
2005-05-19 11:27 ` K.R. Foley [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=428C7830.5070302@cybsft.com \
--to=kr@cybsft.com \
--cc=James.Bottomley@SteelEye.com \
--cc=akpm@osdl.org \
--cc=dino@in.ibm.com \
--cc=gregoire.favre@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.