From: "Grégoire Favre" <gregoire.favre@gmail.com>
To: James Bottomley <James.Bottomley@SteelEye.com>
Cc: dino@in.ibm.com, Andrew Morton <akpm@osdl.org>,
Linux Kernel <linux-kernel@vger.kernel.org>,
SCSI Mailing List <linux-scsi@vger.kernel.org>
Subject: Re: What breaks aic7xxx in post 2.6.12-rc2 ?
Date: Thu, 26 May 2005 19:35:18 +0200 [thread overview]
Message-ID: <20050526173518.GA9132@gmail.com> (raw)
In-Reply-To: <1117118766.4967.22.camel@mulgrave>
On Thu, May 26, 2005 at 10:46:06AM -0400, James Bottomley wrote:
> On Thu, 2005-05-26 at 16:35 +0200, Grégoire Favre wrote:
> > Under 2.6.12-rc2 I haven't this file, what the equivalent ?
>
> It should be there under 2.6.12-rc5
:-) Well, fine, but I can't boot post 2.6.12-rc2 kernels... Just tried
2.6.12-rc5 and it ends here :
Bootdata ok (command line is root=/dev/sdc2 parport=auto video=vesafb:mtrr,ywrap,1024x800-16@75 vga=0xF07 console=ttyS0)
Linux version 2.6.12-rc5 (root@gregoire) (gcc version 3.4.3 20041125 (Gentoo Linux 3.4.3-r1, ssp-3.4.3-0, pie-8.7.7)) #1 Thu May 26 16:53:13 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: root=/dev/sdc2 parport=auto video=vesafb:mtrr,ywrap,1024x800-16@75 vga=0xF07 console=ttyS0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2000.148 MHz processor.
time.c: Using PIT/TSC based timekeeping.
Console: colour VGA+ 80x60
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 1025304k/1048512k available (3138k kernel code, 22512k reserved, 1306k data, 160k init)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
Using local APIC timer interrupts.
Detected 12.500 MHz APIC timer.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
NTFS driver 2.1.22 [Flags: R/O].
EFS: 1.0a - http://aeschi.ch.eu.org/efs/
SGI XFS with large block/inode numbers, no debug enabled
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport0: PC-style at 0x378 [PCSPP(,...)]
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
r8169: NAPI enabled
eth0: RTL8169 at 0xffffc20000002b00, 00:0c:76:bd:22:23, IRQ 16
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC35L120AVVA07-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY DVD RW DRU-500A, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI Floppy, ATAPI FLOPPY drive
hdd: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdd: set_drive_speed_status: error=0x04 { AbortedCommand }
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 31X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
hdd: No disk in drive
hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 29160B Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
target0:0:0: Beginning Domain Validation
WIDTH IS 1
(scsi0:A:0): 6.600MB/s transfers (16bit)
target0:0:0: Domain Validation skipping write tests
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
target0:0:0: Ending Domain Validation
Vendor: SEAGATE Model: ST336706LW Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:15:0: Tagged Queuing enabled. Depth 253
target0:0:15: Beginning Domain Validation
WIDTH IS 1
(scsi0:A:15): 6.600MB/s transfers (16bit)
(scsi0:A:15): 80.000MB/s transfers (40.000MHz, offset 63, 16bit)
target0:0:15: Ending Domain Validation
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
Vendor: TOSHIBA Model: DVD-ROM SD-M1201 Rev: 1R08
Type: CD-ROM ANSI SCSI revision: 02
target1:0:1: Beginning Domain Validation
target1:0:1: Domain Validation skipping write tests
(scsi1:A:1): 20.000MB/s transfers (20.000MHz, offset 15)
scsi1:0:1:0: Attempting to queue an ABORT message
CDB: 0x12 0x0 0x0 0x0 0x60 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State in Data-in phase, at SEQADDR 0x7c
Card was paused
ACCUM = 0x0, SINDEX = 0xb8, DINDEX = 0xa8, ARG_2 = 0x0
HCNT = 0x60 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x40]
SCSISEQ[0x12] SBLKCTL[0x0] SCSIRATE[0xf] SEQCTL[0x10]
SEQ_FLAGS[0x20] SSTAT0[0x0] SSTAT1[0x2] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0xa0]
DFCNTRL[0x38] DFSTATUS[0x40]
STACK: 0x0 0x162 0x192 0x6e
SCB count = 4
Kernel NEXTQSCB = 3
Card NEXTQSCB = 3
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2
HCNT = 0x60 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x40]
SCSISEQ[0x12] SBLKCTL[0x0] SCSIRATE[0xf] SEQCTL[0x10]
SEQ_FLAGS[0x20] SSTAT0[0x0] SSTAT1[0x2] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0xa0]
DFCNTRL[0x38] DFSTATUS[0x40]
STACK: 0x0 0x162 0x192 0x6e
SCB count = 4
Kernel NEXTQSCB = 3
Card NEXTQSCB = 3
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x48] SCB_SCSIID[0x17] SCB_LUN[0x0] SCB_TAG[0x2]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
2 SCB_CONTROL[0x48] SCB_SCSIID[0x17] SCB_LUN[0x0]
Kernel Free SCB list: 1 0
Untagged Q(1): 2
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:1:0: Device is active, asserting ATN
Recovery code sleeping
Recovery code awake
Timer Expired
aic7xxx_abort returns 0x2003
scsi1:0:1:0: Attempting to queue a TARGET RESET message
CDB: 0x12 0x0 0x0 0x0 0x60 0x0
aic7xxx_dev_reset returns 0x2003
Recovery SCB completes
scsi1:0:1:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State in Data-in phase, at SEQADDR 0x7b
Card was paused
ACCUM = 0x0, SINDEX = 0xb8, DINDEX = 0xa8, ARG_2 = 0x0
HCNT = 0x20 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x40]
SCSISEQ[0x12] SBLKCTL[0x0] SCSIRATE[0xf] SEQCTL[0x10]
SEQ_FLAGS[0x20] SSTAT0[0x0] SSTAT1[0x2] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0x80]
DFCNTRL[0x38] DFSTATUS[0x20]
STACK: 0x0 0x162 0x192 0x6e
SCB count = 4
Kernel NEXTQSCB = 2
Card NEXTQSCB = 2
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x8] SCB_SCSIID[0x17] SCB_LUN[0x0] SCB_TAG[0x3]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
3 SCB_CONTROL[0x8] SCB_SCSIID[0€ff] SCB_SCSIIDr anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
r8169: NAPI enabled
eth0: RTL8169 at 0xffffc20000002b00, 00:0c:76:bd:22:23, IRQ 16
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC35L120AVVA07-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY DVD RW DRU-500A, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI Floppy, ATAPI FLOPPY drive
hdd: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdd: set_drive_speed_status: error=0x04 { AbortedCommand }
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 16X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
hdd: No disk in drive
hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 29160B Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
target0:0:0: Beginning Domain Validation
BEGINNING ASYNC, inq len = 164
ASYNC INQUIRY SUCCEEDED
TRYING WIDE ASYNC INQUIRY
(scsi0:A:0): 6.600MB/s transfers (16bit)
ECHO BUFFER HAS LEN 0
DV SETTING TO period 10, offset 255
target0:0:0: Domain Validation skipping write tests
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
target0:0:0: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 15)
target0:0:0: Ending Domain Validation
Vendor: SEAGATE Model: ST336706LW Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:15:0: Tagged Queuing enabled. Depth 253
target0:0:15: Beginning Domain Validation
BEGINNING ASYNC, inq len = 144
ASYNC INQUIRY SUCCEEDED
TRYING WIDE ASYNC INQUIRY
(scsi0:A:15): 6.600MB/s transfers (16bit)
ECHO BUFFER HAS LEN 252
DV SETTING TO period 10, offset 255
(scsi0:A:15): 80.000MB/s transfers (40.000MHz, offset 63, 16bit)
target0:0:15: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 63)
target0:0:15: Ending Domain Validation
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
Vendor: TOSHIBA Model: DVD-ROM SD-M1201 Rev: 1R08
Type: CD-ROM ANSI SCSI revision: 02
target1:0:1: Beginning Domain Validation
BEGINNING ASYNC, inq len = 96
ASYNC INQUIRY SUCCEEDED
ECHO BUFFER HAS LEN 0
DV SETTING TO period 9, offset 255
target1:0:1: Domain Validation skipping write tests
(scsi1:A:1): 20.000MB/s transfers (20.000MHz, offset 15)
scsi1:0:1:0: Attempting to queue an ABORT message
CDB: 0x12 0x0 0x0 0x0 0x60 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State in Data-in phase, at SEQADDR 0x7c
Card was paused
ACCUM = 0x0, SINDEX = 0xb8, DINDEX = 0xa8, ARG_2 = 0x0
€ x17] SCB_LUN[0x0]
Kernel Free SCB list: 1 0
Untagged Q(1): 3
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:1:0: Device is active, asserting ATN
Recovery code sleeping
Recovery code awake
Timer Expired
aic7xxx_abort returns 0x2003
scsi: Device offlined - not ready after error recovery: host 1 channel 0 id 1 lun 0
target1:0:1: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
target1:0:1: Domain Validation detected failure, dropping back
That's with vanilla 2.6.12-rc5 if I have to patch, just tell me :-)
Have a great day,
--
Grégoire Favre
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: "Grégoire Favre" <gregoire.favre@gmail.com>
To: James Bottomley <James.Bottomley@SteelEye.com>
Cc: dino@in.ibm.com, Andrew Morton <akpm@osdl.org>,
Linux Kernel <linux-kernel@vger.kernel.org>,
SCSI Mailing List <linux-scsi@vger.kernel.org>
Subject: Re: What breaks aic7xxx in post 2.6.12-rc2 ?
Date: Thu, 26 May 2005 19:35:18 +0200 [thread overview]
Message-ID: <20050526173518.GA9132@gmail.com> (raw)
In-Reply-To: <1117118766.4967.22.camel@mulgrave>
On Thu, May 26, 2005 at 10:46:06AM -0400, James Bottomley wrote:
> On Thu, 2005-05-26 at 16:35 +0200, Grégoire Favre wrote:
> > Under 2.6.12-rc2 I haven't this file, what the equivalent ?
>
> It should be there under 2.6.12-rc5
:-) Well, fine, but I can't boot post 2.6.12-rc2 kernels... Just tried
2.6.12-rc5 and it ends here :
Bootdata ok (command line is root=/dev/sdc2 parport=auto video=vesafb:mtrr,ywrap,1024x800-16@75 vga=0xF07 console=ttyS0)
Linux version 2.6.12-rc5 (root@gregoire) (gcc version 3.4.3 20041125 (Gentoo Linux 3.4.3-r1, ssp-3.4.3-0, pie-8.7.7)) #1 Thu May 26 16:53:13 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: root=/dev/sdc2 parport=auto video=vesafb:mtrr,ywrap,1024x800-16@75 vga=0xF07 console=ttyS0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2000.148 MHz processor.
time.c: Using PIT/TSC based timekeeping.
Console: colour VGA+ 80x60
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 1025304k/1048512k available (3138k kernel code, 22512k reserved, 1306k data, 160k init)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
Using local APIC timer interrupts.
Detected 12.500 MHz APIC timer.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
NTFS driver 2.1.22 [Flags: R/O].
EFS: 1.0a - http://aeschi.ch.eu.org/efs/
SGI XFS with large block/inode numbers, no debug enabled
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport0: PC-style at 0x378 [PCSPP(,...)]
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
r8169: NAPI enabled
eth0: RTL8169 at 0xffffc20000002b00, 00:0c:76:bd:22:23, IRQ 16
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC35L120AVVA07-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY DVD RW DRU-500A, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI Floppy, ATAPI FLOPPY drive
hdd: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdd: set_drive_speed_status: error=0x04 { AbortedCommand }
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 31X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
hdd: No disk in drive
hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 29160B Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
target0:0:0: Beginning Domain Validation
WIDTH IS 1
(scsi0:A:0): 6.600MB/s transfers (16bit)
target0:0:0: Domain Validation skipping write tests
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
target0:0:0: Ending Domain Validation
Vendor: SEAGATE Model: ST336706LW Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:15:0: Tagged Queuing enabled. Depth 253
target0:0:15: Beginning Domain Validation
WIDTH IS 1
(scsi0:A:15): 6.600MB/s transfers (16bit)
(scsi0:A:15): 80.000MB/s transfers (40.000MHz, offset 63, 16bit)
target0:0:15: Ending Domain Validation
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
Vendor: TOSHIBA Model: DVD-ROM SD-M1201 Rev: 1R08
Type: CD-ROM ANSI SCSI revision: 02
target1:0:1: Beginning Domain Validation
target1:0:1: Domain Validation skipping write tests
(scsi1:A:1): 20.000MB/s transfers (20.000MHz, offset 15)
scsi1:0:1:0: Attempting to queue an ABORT message
CDB: 0x12 0x0 0x0 0x0 0x60 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State in Data-in phase, at SEQADDR 0x7c
Card was paused
ACCUM = 0x0, SINDEX = 0xb8, DINDEX = 0xa8, ARG_2 = 0x0
HCNT = 0x60 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x40]
SCSISEQ[0x12] SBLKCTL[0x0] SCSIRATE[0xf] SEQCTL[0x10]
SEQ_FLAGS[0x20] SSTAT0[0x0] SSTAT1[0x2] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0xa0]
DFCNTRL[0x38] DFSTATUS[0x40]
STACK: 0x0 0x162 0x192 0x6e
SCB count = 4
Kernel NEXTQSCB = 3
Card NEXTQSCB = 3
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2
HCNT = 0x60 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x40]
SCSISEQ[0x12] SBLKCTL[0x0] SCSIRATE[0xf] SEQCTL[0x10]
SEQ_FLAGS[0x20] SSTAT0[0x0] SSTAT1[0x2] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0xa0]
DFCNTRL[0x38] DFSTATUS[0x40]
STACK: 0x0 0x162 0x192 0x6e
SCB count = 4
Kernel NEXTQSCB = 3
Card NEXTQSCB = 3
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x48] SCB_SCSIID[0x17] SCB_LUN[0x0] SCB_TAG[0x2]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
2 SCB_CONTROL[0x48] SCB_SCSIID[0x17] SCB_LUN[0x0]
Kernel Free SCB list: 1 0
Untagged Q(1): 2
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:1:0: Device is active, asserting ATN
Recovery code sleeping
Recovery code awake
Timer Expired
aic7xxx_abort returns 0x2003
scsi1:0:1:0: Attempting to queue a TARGET RESET message
CDB: 0x12 0x0 0x0 0x0 0x60 0x0
aic7xxx_dev_reset returns 0x2003
Recovery SCB completes
scsi1:0:1:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State in Data-in phase, at SEQADDR 0x7b
Card was paused
ACCUM = 0x0, SINDEX = 0xb8, DINDEX = 0xa8, ARG_2 = 0x0
HCNT = 0x20 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x40]
SCSISEQ[0x12] SBLKCTL[0x0] SCSIRATE[0xf] SEQCTL[0x10]
SEQ_FLAGS[0x20] SSTAT0[0x0] SSTAT1[0x2] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0x80]
DFCNTRL[0x38] DFSTATUS[0x20]
STACK: 0x0 0x162 0x192 0x6e
SCB count = 4
Kernel NEXTQSCB = 2
Card NEXTQSCB = 2
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x8] SCB_SCSIID[0x17] SCB_LUN[0x0] SCB_TAG[0x3]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
3 SCB_CONTROL[0x8] SCB_SCSIID[0€ff] SCB_SCSIIDr anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
r8169: NAPI enabled
eth0: RTL8169 at 0xffffc20000002b00, 00:0c:76:bd:22:23, IRQ 16
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC35L120AVVA07-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY DVD RW DRU-500A, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI Floppy, ATAPI FLOPPY drive
hdd: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdd: set_drive_speed_status: error=0x04 { AbortedCommand }
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 16X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
hdd: No disk in drive
hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 29160B Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
target0:0:0: Beginning Domain Validation
BEGINNING ASYNC, inq len = 164
ASYNC INQUIRY SUCCEEDED
TRYING WIDE ASYNC INQUIRY
(scsi0:A:0): 6.600MB/s transfers (16bit)
ECHO BUFFER HAS LEN 0
DV SETTING TO period 10, offset 255
target0:0:0: Domain Validation skipping write tests
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
target0:0:0: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 15)
target0:0:0: Ending Domain Validation
Vendor: SEAGATE Model: ST336706LW Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:15:0: Tagged Queuing enabled. Depth 253
target0:0:15: Beginning Domain Validation
BEGINNING ASYNC, inq len = 144
ASYNC INQUIRY SUCCEEDED
TRYING WIDE ASYNC INQUIRY
(scsi0:A:15): 6.600MB/s transfers (16bit)
ECHO BUFFER HAS LEN 252
DV SETTING TO period 10, offset 255
(scsi0:A:15): 80.000MB/s transfers (40.000MHz, offset 63, 16bit)
target0:0:15: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 63)
target0:0:15: Ending Domain Validation
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
Vendor: TOSHIBA Model: DVD-ROM SD-M1201 Rev: 1R08
Type: CD-ROM ANSI SCSI revision: 02
target1:0:1: Beginning Domain Validation
BEGINNING ASYNC, inq len = 96
ASYNC INQUIRY SUCCEEDED
ECHO BUFFER HAS LEN 0
DV SETTING TO period 9, offset 255
target1:0:1: Domain Validation skipping write tests
(scsi1:A:1): 20.000MB/s transfers (20.000MHz, offset 15)
scsi1:0:1:0: Attempting to queue an ABORT message
CDB: 0x12 0x0 0x0 0x0 0x60 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State in Data-in phase, at SEQADDR 0x7c
Card was paused
ACCUM = 0x0, SINDEX = 0xb8, DINDEX = 0xa8, ARG_2 = 0x0
€ x17] SCB_LUN[0x0]
Kernel Free SCB list: 1 0
Untagged Q(1): 3
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:1:0: Device is active, asserting ATN
Recovery code sleeping
Recovery code awake
Timer Expired
aic7xxx_abort returns 0x2003
scsi: Device offlined - not ready after error recovery: host 1 channel 0 id 1 lun 0
target1:0:1: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
target1:0:1: Domain Validation detected failure, dropping back
That's with vanilla 2.6.12-rc5 if I have to patch, just tell me :-)
Have a great day,
--
Grégoire Favre
next prev parent reply other threads:[~2005-05-26 17:55 UTC|newest]
Thread overview: 109+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-05-16 8:58 What breaks aic7xxx in post 2.6.12-rc2 ? Grégoire Favre
2005-05-16 15:03 ` Jesper Juhl
2005-05-16 15:12 ` What breaks aic7xxx in post 2.6.12-rc2 ? (on amd64 ?) Grégoire Favre
2005-05-16 15:31 ` Jesper Juhl
2005-05-17 7:13 ` What breaks aic7xxx in post 2.6.12-rc2 ? Dinakar Guniguntala
2005-05-17 7:29 ` Andrew Morton
2005-05-17 8:34 ` Dinakar Guniguntala
2005-05-26 7:39 ` Andrew Morton
2005-05-26 10:37 ` K.R. Foley
2005-05-26 10:50 ` Dinakar Guniguntala
2005-05-26 12:59 ` James Bottomley
2005-05-17 14:34 ` James Bottomley
2005-05-17 15:57 ` Grégoire Favre
2005-05-17 15:57 ` Grégoire Favre
2005-05-17 16:38 ` James Bottomley
2005-05-17 16:38 ` James Bottomley
2005-05-17 16:52 ` Grégoire Favre
2005-05-17 16:52 ` Grégoire Favre
2005-05-17 18:16 ` James Bottomley
2005-05-17 18:16 ` James Bottomley
2005-05-17 17:08 ` Dinakar Guniguntala
2005-05-17 18:34 ` James Bottomley
2005-05-17 19:26 ` Grégoire Favre
2005-05-17 19:26 ` Grégoire Favre
2005-05-17 19:50 ` James Bottomley
2005-05-17 19:50 ` James Bottomley
2005-05-17 19:56 ` Grégoire Favre
2005-05-17 19:56 ` Grégoire Favre
2005-05-17 21:06 ` James Bottomley
2005-05-17 21:06 ` James Bottomley
2005-05-17 22:09 ` Grégoire Favre
2005-05-17 22:14 ` James Bottomley
2005-05-17 22:14 ` James Bottomley
2005-05-21 23:22 ` Grégoire Favre
2005-05-21 23:22 ` Grégoire Favre
2005-05-22 13:54 ` James Bottomley
2005-05-22 13:54 ` James Bottomley
2005-05-24 15:39 ` Grégoire Favre
2005-05-24 15:39 ` Grégoire Favre
2005-05-26 13:19 ` James Bottomley
2005-05-26 13:19 ` James Bottomley
2005-05-26 14:35 ` Grégoire Favre
2005-05-26 14:35 ` Grégoire Favre
2005-05-26 14:46 ` James Bottomley
2005-05-26 17:35 ` Grégoire Favre [this message]
2005-05-26 17:35 ` Grégoire Favre
2005-05-30 14:38 ` James Bottomley
2005-05-30 14:38 ` James Bottomley
2005-05-30 14:51 ` Michael Tokarev
2005-05-30 14:59 ` James Bottomley
2005-05-30 15:09 ` Grégoire Favre
2005-05-30 15:09 ` Grégoire Favre
2005-05-30 15:34 ` James Bottomley
2005-05-30 15:34 ` James Bottomley
2005-05-30 16:01 ` Grégoire Favre
2005-05-30 16:01 ` Grégoire Favre
2005-05-30 18:17 ` James Bottomley
2005-05-30 18:17 ` James Bottomley
2005-05-30 19:07 ` Grégoire Favre
2005-05-30 19:07 ` Grégoire Favre
2005-06-06 18:17 ` James Bottomley
2005-06-06 18:17 ` James Bottomley
2005-06-07 8:57 ` Grégoire Favre
2005-06-07 8:57 ` Grégoire Favre
2005-06-12 15:38 ` James Bottomley
2005-06-12 15:38 ` James Bottomley
2005-06-13 14:50 ` Grégoire Favre
2005-06-13 14:50 ` Grégoire Favre
2005-06-13 14:59 ` James Bottomley
2005-06-13 15:05 ` Christoph Hellwig
2005-06-13 15:17 ` Grégoire Favre
2005-06-13 15:17 ` Grégoire Favre
2005-06-13 18:37 ` Gr�goire Favre
2005-06-13 18:37 ` Gr�goire Favre
2005-06-13 20:50 ` James Bottomley
2005-06-13 21:33 ` Gregoire Favre
2005-06-13 21:46 ` James Bottomley
2005-06-13 21:59 ` Gregoire Favre
2005-06-13 22:04 ` James Bottomley
2005-06-13 22:25 ` Gregoire Favre
2005-06-14 2:20 ` James Bottomley
2005-06-14 9:28 ` What breaks aic7xxx in post 2.6.12-rc2 ? (fixed in 2.6.12-rc6 with patches) Gregoire Favre
2005-06-13 21:42 ` What breaks aic7xxx in post 2.6.12-rc2 ? Frank van Maarseveen
2005-06-13 22:59 ` James Bottomley
2005-06-14 21:42 ` Frank van Maarseveen
2005-06-15 12:02 ` Frank van Maarseveen
2005-06-15 14:14 ` James Bottomley
2005-06-15 20:09 ` Frank van Maarseveen
2005-06-15 20:15 ` James Bottomley
2005-06-15 20:15 ` James Bottomley
2005-06-15 20:49 ` Frank van Maarseveen
2005-06-15 20:49 ` Frank van Maarseveen
2005-05-18 9:07 ` Dinakar Guniguntala
2005-05-18 14:12 ` James Bottomley
2005-05-18 14:40 ` Dinakar Guniguntala
2005-05-19 3:07 ` K.R. Foley
2005-05-19 4:23 ` James Bottomley
2005-05-19 9:51 ` Dinakar Guniguntala
2005-05-19 23:56 ` James Bottomley
2005-05-20 1:05 ` K.R. Foley
2005-05-20 1:17 ` James Bottomley
2005-05-20 1:32 ` K.R. Foley
2005-05-20 1:33 ` James Bottomley
2005-05-20 1:40 ` James Bottomley
2005-05-20 1:54 ` K.R. Foley
2005-05-20 2:30 ` James Bottomley
2005-05-20 3:06 ` K.R. Foley
2005-05-20 10:09 ` Dinakar Guniguntala
2005-05-19 11:27 ` K.R. Foley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050526173518.GA9132@gmail.com \
--to=gregoire.favre@gmail.com \
--cc=James.Bottomley@SteelEye.com \
--cc=akpm@osdl.org \
--cc=dino@in.ibm.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.