* [Xenomai-help] Multiple NIC trouble
@ 2007-02-06 21:37 Eric Noulard
2007-02-06 21:56 ` Gilles Chanteperdrix
` (2 more replies)
0 siblings, 3 replies; 19+ messages in thread
From: Eric Noulard @ 2007-02-06 21:37 UTC (permalink / raw)
To: Xenomai help
I am about to begin to use Xenomai
on a dual-core x86_64 box.
I installed FC6 i386 (32bits) since the adeos patch for x86_64
was not there when I did the install, I may go back
to run xenomai on x86_64 since I install both systems (x86_64 and i386)
Nevertheless I have three 32bits kernels
2.6.19-vanilla (pure kernel.org kernel)
2.6.20-rc1-rtXX (precompiled from Ingo Molnar)
2.6.19-xenomai (vanilla + adeos-ipipe-2.6.19-i386-1.6-03.patch)
The box has 3 ethernet interface (2 on-board + 1 on an additionnal NIC)
eth0 is the additionnal NIC
eth1,eth2 the on-board I/F
eth1 used for corporate LAN
eth0 "should" be used for private network (only 2 machines for now)
With this config the machine boots properly with the non-xenomai
kernels with eth1 and eth0 up and running.
If I boot the xenomai kernel the machine hangs
(even sysrq does not help) as soon as the system tries to ifup eth0.
If I disable eth0 the xenomai kernel boots until the end.
If I try to ifup eth0 "manually" afterward I got the same "hang".
I have no log and sysrq does not work !!
How would you suggest me to investigate that problem?
--
Erk
^ permalink raw reply [flat|nested] 19+ messages in thread* Re: [Xenomai-help] Multiple NIC trouble 2007-02-06 21:37 [Xenomai-help] Multiple NIC trouble Eric Noulard @ 2007-02-06 21:56 ` Gilles Chanteperdrix 2007-02-07 7:57 ` Eric Noulard 2007-02-06 21:59 ` Jan Kiszka 2007-02-06 23:39 ` Philippe Gerum 2 siblings, 1 reply; 19+ messages in thread From: Gilles Chanteperdrix @ 2007-02-06 21:56 UTC (permalink / raw) To: Eric Noulard; +Cc: Xenomai help Eric Noulard wrote: > How would you suggest me to investigate that problem? You should tell us what driver use your eth0 board, in order to see if other people are able to reproduce the problem you have. Try enabling kernel debugging and NMI watchdog. If it does not help, then add printks in your ethernet driver code to try and see where exactly it hangs. Then show here the result of your investigations, maybe people will have an idea of why it hangs. -- Gilles Chanteperdrix. ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-06 21:56 ` Gilles Chanteperdrix @ 2007-02-07 7:57 ` Eric Noulard 2007-02-07 11:28 ` Jan Kiszka 0 siblings, 1 reply; 19+ messages in thread From: Eric Noulard @ 2007-02-07 7:57 UTC (permalink / raw) To: Xenomai help [-- Attachment #1: Type: text/plain, Size: 2880 bytes --] 2007/2/6, Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>: > Eric Noulard wrote: > > How would you suggest me to investigate that problem? > > You should tell us what driver use your eth0 board, in order to see if > other people are able to reproduce the problem you have. Right. The driver is tg3. Embbeded NIC and the PCI are of the same type but I just discover different revision 11 vs 21. lspci gives: 01:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 21) 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11) 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11) > Try enabling > kernel debugging and NMI watchdog. If it does not help, then add printks > in your ethernet driver code to try and see where exactly it hangs. Then > show here the result of your investigations, maybe people will have an > idea of why it hangs. I will do the rcompile with option and reboot may be tomorrow or the day after since I have not the time for this now. So don't be surprised if do not answer too quickly. I'm definitely interested in your advice. 2007/2/6, Jan Kiszka <jan.kiszka@domain.hid>: > o check if you have MSI enabled, if yes, try to disable it Sorry but I don't know what MSI is? Could you tell me how to check (and may be some pointer to valuable information which explains what it is)? > > o try cpus=1 or !SMP I'll try that within 1 or 2 days. > > o check if ipipe-1.7-00 makes a difference (it shouldn't, the fixed > issue in 1.6-03 showed a different bug pattern) I will try that too. > > o post your .config so that we can have a look As a beginning I attach the current .config 2007/2/7, Philippe Gerum <rpm@xenomai.org>: > > - try disabling Xenomai (CONFIG_XENOMAI) while keeping the interrupt > pipeline (CONFIG_IPIPE) enabled; does the kernel boot properly? Will try this soon too. > > - What does /proc/interrupts say on a sane configuration (i.e. that > boots)? here it is: --------- cat /proc/interrupts CPU0 CPU1 0: 542 0 IO-APIC-edge timer 1: 2 0 IO-APIC-edge i8042 8: 3 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-fasteoi acpi 12: 4 0 IO-APIC-edge i8042 14: 1396 502073 IO-APIC-edge ide0 16: 548697 0 IO-APIC-fasteoi eth1 17: 0 0 IO-APIC-fasteoi uhci_hcd:usb2 18: 65 0 IO-APIC-fasteoi uhci_hcd:usb3 20: 18125 19871 IO-APIC-fasteoi uhci_hcd:usb1, ehci_hcd:usb4, libata 219: 11 27 PCI-MSI-edge eth0 NMI: 0 0 LOC: 1382467 1312913 ERR: 0 MIS: 0 --------------------- -- Erk [-- Attachment #2: config-2.6.19-xenomai-2.3 --] [-- Type: application/octet-stream, Size: 64290 bytes --] # # Automatically generated make config: don't edit # Linux kernel version: 2.6.19-xenomai-2.3 # Fri Jan 19 11:12:32 2007 # CONFIG_X86_32=y CONFIG_GENERIC_TIME=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_SEMAPHORE_SLEEPERS=y CONFIG_X86=y CONFIG_MMU=y CONFIG_GENERIC_ISA_DMA=y CONFIG_GENERIC_IOMAP=y CONFIG_GENERIC_HWEIGHT=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y CONFIG_DMI=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # Code maturity level options # CONFIG_EXPERIMENTAL=y CONFIG_LOCK_KERNEL=y CONFIG_INIT_ENV_ARG_LIMIT=32 # # General setup # CONFIG_LOCALVERSION="" # CONFIG_LOCALVERSION_AUTO is not set CONFIG_SWAP=y CONFIG_SYSVIPC=y # CONFIG_IPC_NS is not set CONFIG_POSIX_MQUEUE=y CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set CONFIG_TASKSTATS=y CONFIG_TASK_DELAY_ACCT=y # CONFIG_UTS_NS is not set CONFIG_AUDIT=y CONFIG_AUDITSYSCALL=y # CONFIG_IKCONFIG is not set CONFIG_CPUSETS=y CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" CONFIG_CC_OPTIMIZE_FOR_SIZE=y # CONFIG_TASK_XACCT is not set CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_UID16=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set CONFIG_KALLSYMS_EXTRA_PASS=y CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y CONFIG_SLAB=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 # CONFIG_SLOB is not set # # Loadable module support # CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y CONFIG_STOP_MACHINE=y # # Block layer # CONFIG_BLOCK=y CONFIG_LBD=y CONFIG_BLK_DEV_IO_TRACE=y CONFIG_LSF=y # # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y CONFIG_IOSCHED_CFQ=y # CONFIG_DEFAULT_AS is not set # CONFIG_DEFAULT_DEADLINE is not set CONFIG_DEFAULT_CFQ=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="cfq" # # Real-time sub-system # CONFIG_XENOMAI=y CONFIG_XENO_OPT_NUCLEUS=y CONFIG_XENO_OPT_PERVASIVE=y # CONFIG_XENO_OPT_ISHIELD is not set # CONFIG_XENO_OPT_RPIDISABLE is not set CONFIG_XENO_OPT_SECURITY_ACCESS=y CONFIG_XENO_OPT_PIPELINE_HEAD=y CONFIG_XENO_OPT_PIPE=y CONFIG_XENO_OPT_PIPE_NRDEV=32 CONFIG_XENO_OPT_REGISTRY=y CONFIG_XENO_OPT_REGISTRY_NRSLOTS=512 CONFIG_XENO_OPT_SYS_HEAPSZ=128 CONFIG_XENO_OPT_STATS=y # CONFIG_XENO_OPT_DEBUG is not set # # Timing # # CONFIG_XENO_OPT_TIMING_PERIODIC is not set CONFIG_XENO_OPT_TIMING_PERIOD=0 CONFIG_XENO_OPT_TIMING_TIMERLAT=0 CONFIG_XENO_OPT_TIMING_SCHEDLAT=0 # # Scalability # # CONFIG_XENO_OPT_SCALABLE_SCHED is not set CONFIG_XENO_OPT_TIMER_LIST=y # CONFIG_XENO_OPT_TIMER_HEAP is not set # CONFIG_XENO_OPT_TIMER_WHEEL is not set # # Shared interrupts # # CONFIG_XENO_OPT_SHIRQ_LEVEL is not set # CONFIG_XENO_OPT_SHIRQ_EDGE is not set # # Machine # CONFIG_XENO_HW_FPU=y # # NMI watchdog # # CONFIG_XENO_HW_NMI_DEBUG_LATENCY is not set # # SMI workaround # # CONFIG_XENO_HW_SMI_DETECT_DISABLE is not set CONFIG_XENO_HW_SMI_DETECT=y # CONFIG_XENO_HW_SMI_WORKAROUND is not set # # Interfaces # CONFIG_XENO_SKIN_NATIVE=y CONFIG_XENO_OPT_NATIVE_PIPE=y CONFIG_XENO_OPT_NATIVE_PIPE_BUFSZ=4096 CONFIG_XENO_OPT_NATIVE_REGISTRY=y CONFIG_XENO_OPT_NATIVE_SEM=y CONFIG_XENO_OPT_NATIVE_EVENT=y CONFIG_XENO_OPT_NATIVE_MUTEX=y CONFIG_XENO_OPT_NATIVE_COND=y CONFIG_XENO_OPT_NATIVE_QUEUE=y CONFIG_XENO_OPT_NATIVE_HEAP=y CONFIG_XENO_OPT_NATIVE_ALARM=y CONFIG_XENO_OPT_NATIVE_MPS=y # CONFIG_XENO_OPT_NATIVE_INTR is not set CONFIG_XENO_SKIN_POSIX=y CONFIG_XENO_OPT_POSIX_SHM=y # CONFIG_XENO_OPT_POSIX_INTR is not set CONFIG_XENO_OPT_DEBUG_POSIX=y # CONFIG_XENO_SKIN_PSOS is not set # CONFIG_XENO_SKIN_UITRON is not set # CONFIG_XENO_SKIN_VRTX is not set CONFIG_XENO_SKIN_VXWORKS=m # CONFIG_XENO_SKIN_RTAI is not set CONFIG_XENO_SKIN_RTDM=y CONFIG_XENO_OPT_RTDM_FILDES=128 # # Drivers # # # Serial drivers # CONFIG_XENO_DRIVERS_16550A=m # # Testing drivers # CONFIG_XENO_DRIVERS_TIMERBENCH=m CONFIG_XENO_DRIVERS_IRQBENCH=m CONFIG_XENO_DRIVERS_SWITCHTEST=m # # CAN drivers # # CONFIG_XENO_DRIVERS_CAN is not set # # Processor type and features # CONFIG_SMP=y CONFIG_X86_PC=y # CONFIG_X86_ELAN is not set # CONFIG_X86_VOYAGER is not set # CONFIG_X86_NUMAQ is not set # CONFIG_X86_SUMMIT is not set # CONFIG_X86_BIGSMP is not set # CONFIG_X86_VISWS is not set # CONFIG_X86_GENERICARCH is not set # CONFIG_X86_ES7000 is not set # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set # CONFIG_M586TSC is not set # CONFIG_M586MMX is not set CONFIG_M686=y # CONFIG_MPENTIUMII is not set # CONFIG_MPENTIUMIII is not set # CONFIG_MPENTIUMM is not set # CONFIG_MPENTIUM4 is not set # CONFIG_MK6 is not set # CONFIG_MK7 is not set # CONFIG_MK8 is not set # CONFIG_MCRUSOE is not set # CONFIG_MEFFICEON is not set # CONFIG_MWINCHIPC6 is not set # CONFIG_MWINCHIP2 is not set # CONFIG_MWINCHIP3D is not set # CONFIG_MGEODEGX1 is not set # CONFIG_MGEODE_LX is not set # CONFIG_MCYRIXIII is not set # CONFIG_MVIAC3_2 is not set # CONFIG_X86_GENERIC is not set CONFIG_X86_CMPXCHG=y CONFIG_X86_XADD=y CONFIG_X86_L1_CACHE_SHIFT=5 CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_X86_PPRO_FENCE=y CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y CONFIG_X86_CMPXCHG64=y CONFIG_X86_GOOD_APIC=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_TSC=y CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_NR_CPUS=64 CONFIG_SCHED_SMT=y CONFIG_SCHED_MC=y # CONFIG_PREEMPT_NONE is not set CONFIG_PREEMPT_VOLUNTARY=y # CONFIG_PREEMPT is not set CONFIG_PREEMPT_BKL=y CONFIG_IPIPE=y CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y CONFIG_X86_MCE=y # CONFIG_X86_MCE_NONFATAL is not set # CONFIG_X86_MCE_P4THERMAL is not set CONFIG_VM86=y # CONFIG_TOSHIBA is not set # CONFIG_I8K is not set # CONFIG_X86_REBOOTFIXUPS is not set CONFIG_MICROCODE=m CONFIG_MICROCODE_OLD_INTERFACE=y CONFIG_X86_MSR=y CONFIG_X86_CPUID=y # # Firmware Drivers # CONFIG_EDD=m CONFIG_DELL_RBU=m CONFIG_DCDBAS=m CONFIG_NOHIGHMEM=y # CONFIG_HIGHMEM4G is not set # CONFIG_HIGHMEM64G is not set CONFIG_PAGE_OFFSET=0xC0000000 CONFIG_NEED_NODE_MEMMAP_SIZE=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_SPARSEMEM_ENABLE=y CONFIG_ARCH_SELECT_MEMORY_MODEL=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y # CONFIG_FLATMEM_MANUAL is not set # CONFIG_DISCONTIGMEM_MANUAL is not set CONFIG_SPARSEMEM_MANUAL=y CONFIG_SPARSEMEM=y CONFIG_HAVE_MEMORY_PRESENT=y CONFIG_SPARSEMEM_STATIC=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y # CONFIG_MATH_EMULATION is not set CONFIG_MTRR=y CONFIG_IRQBALANCE=y CONFIG_REGPARM=y # CONFIG_SECCOMP is not set # CONFIG_HZ_100 is not set # CONFIG_HZ_250 is not set CONFIG_HZ_1000=y CONFIG_HZ=1000 CONFIG_KEXEC=y CONFIG_PHYSICAL_START=0x100000 CONFIG_HOTPLUG_CPU=y CONFIG_COMPAT_VDSO=y # # Power management options (ACPI, APM) # # CONFIG_PM is not set # # ACPI (Advanced Configuration and Power Interface) Support # # CONFIG_ACPI is not set # # CPU Frequency scaling # # CONFIG_CPU_FREQ is not set # # Bus options (PCI, PCMCIA, EISA, MCA, ISA) # CONFIG_PCI=y # CONFIG_PCI_GOBIOS is not set # CONFIG_PCI_GOMMCONFIG is not set # CONFIG_PCI_GODIRECT is not set CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y CONFIG_PCIEPORTBUS=y CONFIG_HOTPLUG_PCI_PCIE=m # CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE is not set CONFIG_PCI_MSI=y # CONFIG_PCI_DEBUG is not set CONFIG_HT_IRQ=y CONFIG_ISA_DMA_API=y # CONFIG_ISA is not set # CONFIG_MCA is not set # CONFIG_SCx200 is not set CONFIG_K8_NB=y # # PCCARD (PCMCIA/CardBus) support # CONFIG_PCCARD=y # CONFIG_PCMCIA_DEBUG is not set CONFIG_PCMCIA=y CONFIG_PCMCIA_LOAD_CIS=y CONFIG_PCMCIA_IOCTL=y CONFIG_CARDBUS=y # # PC-card bridges # CONFIG_YENTA=y CONFIG_YENTA_O2=y CONFIG_YENTA_RICOH=y CONFIG_YENTA_TI=y CONFIG_YENTA_ENE_TUNE=y CONFIG_YENTA_TOSHIBA=y CONFIG_PD6729=m CONFIG_I82092=m CONFIG_PCCARD_NONSTATIC=y # # PCI Hotplug Support # CONFIG_HOTPLUG_PCI=y CONFIG_HOTPLUG_PCI_FAKE=m # CONFIG_HOTPLUG_PCI_COMPAQ is not set # CONFIG_HOTPLUG_PCI_IBM is not set # CONFIG_HOTPLUG_PCI_CPCI is not set CONFIG_HOTPLUG_PCI_SHPC=m # CONFIG_HOTPLUG_PCI_SHPC_POLL_EVENT_MODE is not set # # Executable file formats # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_AOUT is not set CONFIG_BINFMT_MISC=y # # Networking # CONFIG_NET=y # # Networking options # # CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y CONFIG_XFRM=y CONFIG_XFRM_USER=y # CONFIG_XFRM_SUB_POLICY is not set CONFIG_NET_KEY=m CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_ADVANCED_ROUTER=y CONFIG_ASK_IP_FIB_HASH=y # CONFIG_IP_FIB_TRIE is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_MULTIPLE_TABLES=y CONFIG_IP_ROUTE_FWMARK=y CONFIG_IP_ROUTE_MULTIPATH=y # CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set CONFIG_IP_ROUTE_VERBOSE=y # CONFIG_IP_PNP is not set CONFIG_NET_IPIP=m CONFIG_NET_IPGRE=m CONFIG_NET_IPGRE_BROADCAST=y CONFIG_IP_MROUTE=y CONFIG_IP_PIMSM_V1=y CONFIG_IP_PIMSM_V2=y # CONFIG_ARPD is not set CONFIG_SYN_COOKIES=y CONFIG_INET_AH=m CONFIG_INET_ESP=m CONFIG_INET_IPCOMP=m CONFIG_INET_XFRM_TUNNEL=m CONFIG_INET_TUNNEL=m CONFIG_INET_XFRM_MODE_TRANSPORT=m CONFIG_INET_XFRM_MODE_TUNNEL=m CONFIG_INET_XFRM_MODE_BEET=y CONFIG_INET_DIAG=m CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_ADVANCED=y CONFIG_TCP_CONG_BIC=y CONFIG_TCP_CONG_CUBIC=m CONFIG_TCP_CONG_WESTWOOD=m CONFIG_TCP_CONG_HTCP=m CONFIG_TCP_CONG_HSTCP=m CONFIG_TCP_CONG_HYBLA=m CONFIG_TCP_CONG_VEGAS=m CONFIG_TCP_CONG_SCALABLE=m CONFIG_TCP_CONG_LP=m CONFIG_TCP_CONG_VENO=m CONFIG_DEFAULT_BIC=y # CONFIG_DEFAULT_CUBIC is not set # CONFIG_DEFAULT_HTCP is not set # CONFIG_DEFAULT_VEGAS is not set # CONFIG_DEFAULT_WESTWOOD is not set # CONFIG_DEFAULT_RENO is not set CONFIG_DEFAULT_TCP_CONG="bic" # # IP: Virtual Server Configuration # CONFIG_IP_VS=m # CONFIG_IP_VS_DEBUG is not set CONFIG_IP_VS_TAB_BITS=12 # # IPVS transport protocol load balancing support # CONFIG_IP_VS_PROTO_TCP=y CONFIG_IP_VS_PROTO_UDP=y CONFIG_IP_VS_PROTO_ESP=y CONFIG_IP_VS_PROTO_AH=y # # IPVS scheduler # CONFIG_IP_VS_RR=m CONFIG_IP_VS_WRR=m CONFIG_IP_VS_LC=m CONFIG_IP_VS_WLC=m CONFIG_IP_VS_LBLC=m CONFIG_IP_VS_LBLCR=m CONFIG_IP_VS_DH=m CONFIG_IP_VS_SH=m CONFIG_IP_VS_SED=m CONFIG_IP_VS_NQ=m # # IPVS application helper # CONFIG_IP_VS_FTP=m CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y CONFIG_IPV6_ROUTE_INFO=y CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m # CONFIG_IPV6_MIP6 is not set CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_INET6_XFRM_MODE_TRANSPORT=m CONFIG_INET6_XFRM_MODE_TUNNEL=m CONFIG_INET6_XFRM_MODE_BEET=m # CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set CONFIG_IPV6_SIT=m CONFIG_IPV6_TUNNEL=m # CONFIG_IPV6_MULTIPLE_TABLES is not set CONFIG_NETLABEL=y CONFIG_NETWORK_SECMARK=y CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set CONFIG_BRIDGE_NETFILTER=y # # Core Netfilter Configuration # CONFIG_NETFILTER_NETLINK=m CONFIG_NETFILTER_NETLINK_QUEUE=m CONFIG_NETFILTER_NETLINK_LOG=m CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m # CONFIG_NETFILTER_XT_TARGET_DSCP is not set CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_SECMARK=m CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m CONFIG_NETFILTER_XT_MATCH_CONNMARK=m CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m # CONFIG_NETFILTER_XT_MATCH_DSCP is not set CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m CONFIG_NETFILTER_XT_MATCH_POLICY=m CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # # IP: Netfilter Configuration # CONFIG_IP_NF_CONNTRACK=m CONFIG_IP_NF_CT_ACCT=y CONFIG_IP_NF_CONNTRACK_MARK=y CONFIG_IP_NF_CONNTRACK_SECMARK=y CONFIG_IP_NF_CONNTRACK_EVENTS=y CONFIG_IP_NF_CONNTRACK_NETLINK=m CONFIG_IP_NF_CT_PROTO_SCTP=m CONFIG_IP_NF_FTP=m CONFIG_IP_NF_IRC=m CONFIG_IP_NF_NETBIOS_NS=m CONFIG_IP_NF_TFTP=m CONFIG_IP_NF_AMANDA=m CONFIG_IP_NF_PPTP=m CONFIG_IP_NF_H323=m CONFIG_IP_NF_SIP=m CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_IPRANGE=m CONFIG_IP_NF_MATCH_TOS=m CONFIG_IP_NF_MATCH_RECENT=m CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_MATCH_OWNER=m CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_HASHLIMIT=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m CONFIG_IP_NF_TARGET_ULOG=m CONFIG_IP_NF_TARGET_TCPMSS=m CONFIG_IP_NF_NAT=m CONFIG_IP_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m CONFIG_IP_NF_TARGET_SAME=m CONFIG_IP_NF_NAT_SNMP_BASIC=m CONFIG_IP_NF_NAT_IRC=m CONFIG_IP_NF_NAT_FTP=m CONFIG_IP_NF_NAT_TFTP=m CONFIG_IP_NF_NAT_AMANDA=m CONFIG_IP_NF_NAT_PPTP=m CONFIG_IP_NF_NAT_H323=m CONFIG_IP_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m CONFIG_IP_NF_ARP_MANGLE=m # # IPv6: Netfilter Configuration (EXPERIMENTAL) # CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_FRAG=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_OWNER=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_LOG=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m CONFIG_IP6_NF_RAW=m # # DECnet: Netfilter Configuration # # CONFIG_DECNET_NF_GRABULATOR is not set # # Bridge: Netfilter Configuration # CONFIG_BRIDGE_NF_EBTABLES=m CONFIG_BRIDGE_EBT_BROUTE=m CONFIG_BRIDGE_EBT_T_FILTER=m CONFIG_BRIDGE_EBT_T_NAT=m CONFIG_BRIDGE_EBT_802_3=m CONFIG_BRIDGE_EBT_AMONG=m CONFIG_BRIDGE_EBT_ARP=m CONFIG_BRIDGE_EBT_IP=m CONFIG_BRIDGE_EBT_LIMIT=m CONFIG_BRIDGE_EBT_MARK=m CONFIG_BRIDGE_EBT_PKTTYPE=m CONFIG_BRIDGE_EBT_STP=m CONFIG_BRIDGE_EBT_VLAN=m CONFIG_BRIDGE_EBT_ARPREPLY=m CONFIG_BRIDGE_EBT_DNAT=m CONFIG_BRIDGE_EBT_MARK_T=m CONFIG_BRIDGE_EBT_REDIRECT=m CONFIG_BRIDGE_EBT_SNAT=m CONFIG_BRIDGE_EBT_LOG=m CONFIG_BRIDGE_EBT_ULOG=m # # DCCP Configuration (EXPERIMENTAL) # CONFIG_IP_DCCP=m CONFIG_INET_DCCP_DIAG=m CONFIG_IP_DCCP_ACKVEC=y # # DCCP CCIDs Configuration (EXPERIMENTAL) # CONFIG_IP_DCCP_CCID2=m # CONFIG_IP_DCCP_CCID2_DEBUG is not set CONFIG_IP_DCCP_CCID3=m CONFIG_IP_DCCP_TFRC_LIB=m # # DCCP Kernel Hacking # # CONFIG_IP_DCCP_DEBUG is not set # CONFIG_NET_DCCPPROBE is not set # # SCTP Configuration (EXPERIMENTAL) # CONFIG_IP_SCTP=m # CONFIG_SCTP_DBG_MSG is not set # CONFIG_SCTP_DBG_OBJCNT is not set # CONFIG_SCTP_HMAC_NONE is not set # CONFIG_SCTP_HMAC_SHA1 is not set CONFIG_SCTP_HMAC_MD5=y # # TIPC Configuration (EXPERIMENTAL) # CONFIG_TIPC=m # CONFIG_TIPC_ADVANCED is not set # CONFIG_TIPC_DEBUG is not set CONFIG_ATM=m CONFIG_ATM_CLIP=m # CONFIG_ATM_CLIP_NO_ICMP is not set CONFIG_ATM_LANE=m # CONFIG_ATM_MPOA is not set CONFIG_ATM_BR2684=m # CONFIG_ATM_BR2684_IPFILTER is not set CONFIG_BRIDGE=m CONFIG_VLAN_8021Q=m CONFIG_DECNET=m CONFIG_DECNET_ROUTER=y CONFIG_DECNET_ROUTE_FWMARK=y CONFIG_LLC=y # CONFIG_LLC2 is not set CONFIG_IPX=m # CONFIG_IPX_INTERN is not set CONFIG_ATALK=m CONFIG_DEV_APPLETALK=m CONFIG_IPDDP=m CONFIG_IPDDP_ENCAP=y CONFIG_IPDDP_DECAP=y # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_ECONET is not set CONFIG_WAN_ROUTER=m # # QoS and/or fair queueing # CONFIG_NET_SCHED=y # CONFIG_NET_SCH_CLK_JIFFIES is not set CONFIG_NET_SCH_CLK_GETTIMEOFDAY=y # CONFIG_NET_SCH_CLK_CPU is not set # # Queueing/Scheduling # CONFIG_NET_SCH_CBQ=m CONFIG_NET_SCH_HTB=m CONFIG_NET_SCH_HFSC=m CONFIG_NET_SCH_ATM=m CONFIG_NET_SCH_PRIO=m CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m CONFIG_NET_SCH_TBF=m CONFIG_NET_SCH_GRED=m CONFIG_NET_SCH_DSMARK=m CONFIG_NET_SCH_NETEM=m CONFIG_NET_SCH_INGRESS=m # # Classification # CONFIG_NET_CLS=y CONFIG_NET_CLS_BASIC=m CONFIG_NET_CLS_TCINDEX=m CONFIG_NET_CLS_ROUTE4=m CONFIG_NET_CLS_ROUTE=y CONFIG_NET_CLS_FW=m CONFIG_NET_CLS_U32=m CONFIG_CLS_U32_PERF=y CONFIG_CLS_U32_MARK=y CONFIG_NET_CLS_RSVP=m CONFIG_NET_CLS_RSVP6=m CONFIG_NET_EMATCH=y CONFIG_NET_EMATCH_STACK=32 CONFIG_NET_EMATCH_CMP=m CONFIG_NET_EMATCH_NBYTE=m CONFIG_NET_EMATCH_U32=m CONFIG_NET_EMATCH_META=m CONFIG_NET_EMATCH_TEXT=m CONFIG_NET_CLS_ACT=y CONFIG_NET_ACT_POLICE=m CONFIG_NET_ACT_GACT=m CONFIG_GACT_PROB=y CONFIG_NET_ACT_MIRRED=m CONFIG_NET_ACT_IPT=m CONFIG_NET_ACT_PEDIT=m CONFIG_NET_ACT_SIMP=m CONFIG_NET_CLS_IND=y CONFIG_NET_ESTIMATOR=y # # Network testing # CONFIG_NET_PKTGEN=m # CONFIG_NET_TCPPROBE is not set # CONFIG_HAMRADIO is not set CONFIG_IRDA=m # # IrDA protocols # CONFIG_IRLAN=m CONFIG_IRNET=m CONFIG_IRCOMM=m # CONFIG_IRDA_ULTRA is not set # # IrDA options # CONFIG_IRDA_CACHE_LAST_LSAP=y CONFIG_IRDA_FAST_RR=y # CONFIG_IRDA_DEBUG is not set # # Infrared-port device drivers # # # SIR device drivers # CONFIG_IRTTY_SIR=m # # Dongle support # CONFIG_DONGLE=y CONFIG_ESI_DONGLE=m CONFIG_ACTISYS_DONGLE=m CONFIG_TEKRAM_DONGLE=m CONFIG_TOIM3232_DONGLE=m CONFIG_LITELINK_DONGLE=m CONFIG_MA600_DONGLE=m CONFIG_GIRBIL_DONGLE=m CONFIG_MCP2120_DONGLE=m CONFIG_OLD_BELKIN_DONGLE=m CONFIG_ACT200L_DONGLE=m # # Old SIR device drivers # # # Old Serial dongle support # # # FIR device drivers # CONFIG_USB_IRDA=m CONFIG_SIGMATEL_FIR=m CONFIG_NSC_FIR=m CONFIG_WINBOND_FIR=m # CONFIG_TOSHIBA_FIR is not set CONFIG_SMC_IRCC_FIR=m CONFIG_ALI_FIR=m CONFIG_VLSI_FIR=m CONFIG_VIA_FIR=m CONFIG_MCS_FIR=m CONFIG_BT=m CONFIG_BT_L2CAP=m CONFIG_BT_SCO=m CONFIG_BT_RFCOMM=m CONFIG_BT_RFCOMM_TTY=y CONFIG_BT_BNEP=m CONFIG_BT_BNEP_MC_FILTER=y CONFIG_BT_BNEP_PROTO_FILTER=y CONFIG_BT_HIDP=m # # Bluetooth device drivers # CONFIG_BT_HCIUSB=m CONFIG_BT_HCIUSB_SCO=y CONFIG_BT_HCIUART=m CONFIG_BT_HCIUART_H4=y CONFIG_BT_HCIUART_BCSP=y CONFIG_BT_HCIBCM203X=m CONFIG_BT_HCIBPA10X=m CONFIG_BT_HCIBFUSB=m CONFIG_BT_HCIDTL1=m CONFIG_BT_HCIBT3C=m CONFIG_BT_HCIBLUECARD=m CONFIG_BT_HCIBTUART=m CONFIG_BT_HCIVHCI=m CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m CONFIG_IEEE80211_CRYPT_TKIP=m CONFIG_IEEE80211_SOFTMAC=m CONFIG_IEEE80211_SOFTMAC_DEBUG=y CONFIG_WIRELESS_EXT=y CONFIG_FIB_RULES=y # # Device Drivers # # # Generic Driver Options # CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y # CONFIG_DEBUG_DRIVER is not set # CONFIG_SYS_HYPERVISOR is not set # # Connector - unified userspace <-> kernelspace linker # CONFIG_CONNECTOR=y CONFIG_PROC_EVENTS=y # # Memory Technology Devices (MTD) # CONFIG_MTD=m # CONFIG_MTD_DEBUG is not set CONFIG_MTD_CONCAT=m CONFIG_MTD_PARTITIONS=y CONFIG_MTD_REDBOOT_PARTS=m CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1 # CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set # CONFIG_MTD_REDBOOT_PARTS_READONLY is not set # # User Modules And Translation Layers # CONFIG_MTD_CHAR=m CONFIG_MTD_BLOCK=m CONFIG_MTD_BLOCK_RO=m CONFIG_FTL=m CONFIG_NFTL=m CONFIG_NFTL_RW=y CONFIG_INFTL=m CONFIG_RFD_FTL=m # CONFIG_SSFDC is not set # # RAM/ROM/Flash chip drivers # CONFIG_MTD_CFI=m CONFIG_MTD_JEDECPROBE=m CONFIG_MTD_GEN_PROBE=m # CONFIG_MTD_CFI_ADV_OPTIONS is not set CONFIG_MTD_MAP_BANK_WIDTH_1=y CONFIG_MTD_MAP_BANK_WIDTH_2=y CONFIG_MTD_MAP_BANK_WIDTH_4=y # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set CONFIG_MTD_CFI_I1=y CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I4 is not set # CONFIG_MTD_CFI_I8 is not set CONFIG_MTD_CFI_INTELEXT=m CONFIG_MTD_CFI_AMDSTD=m CONFIG_MTD_CFI_STAA=m CONFIG_MTD_CFI_UTIL=m CONFIG_MTD_RAM=m CONFIG_MTD_ROM=m CONFIG_MTD_ABSENT=m # CONFIG_MTD_OBSOLETE_CHIPS is not set # # Mapping drivers for chip access # CONFIG_MTD_COMPLEX_MAPPINGS=y # CONFIG_MTD_PHYSMAP is not set # CONFIG_MTD_PNC2000 is not set CONFIG_MTD_SC520CDP=m CONFIG_MTD_NETSC520=m CONFIG_MTD_TS5500=m # CONFIG_MTD_SBC_GXX is not set # CONFIG_MTD_AMD76XROM is not set # CONFIG_MTD_ICHXROM is not set CONFIG_MTD_SCB2_FLASH=m # CONFIG_MTD_NETtel is not set # CONFIG_MTD_DILNETPC is not set # CONFIG_MTD_L440GX is not set CONFIG_MTD_PCI=m # CONFIG_MTD_PLATRAM is not set # # Self-contained MTD device drivers # CONFIG_MTD_PMC551=m # CONFIG_MTD_PMC551_BUGFIX is not set # CONFIG_MTD_PMC551_DEBUG is not set # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set CONFIG_MTD_MTDRAM=m CONFIG_MTDRAM_TOTAL_SIZE=4096 CONFIG_MTDRAM_ERASE_SIZE=128 CONFIG_MTD_BLOCK2MTD=m # # Disk-On-Chip Device Drivers # # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set # # NAND Flash Device Drivers # CONFIG_MTD_NAND=m # CONFIG_MTD_NAND_VERIFY_WRITE is not set CONFIG_MTD_NAND_ECC_SMC=y CONFIG_MTD_NAND_IDS=m CONFIG_MTD_NAND_DISKONCHIP=m # CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0 # CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set # CONFIG_MTD_NAND_CS553X is not set CONFIG_MTD_NAND_NANDSIM=m # # OneNAND Flash Device Drivers # # CONFIG_MTD_ONENAND is not set # # Parallel port support # CONFIG_PARPORT=m CONFIG_PARPORT_PC=m CONFIG_PARPORT_SERIAL=m # CONFIG_PARPORT_PC_FIFO is not set # CONFIG_PARPORT_PC_SUPERIO is not set CONFIG_PARPORT_PC_PCMCIA=m CONFIG_PARPORT_NOT_PC=y # CONFIG_PARPORT_GSC is not set # CONFIG_PARPORT_AX88796 is not set CONFIG_PARPORT_1284=y # # Plug and Play support # # # Block devices # CONFIG_BLK_DEV_FD=m CONFIG_PARIDE=m CONFIG_PARIDE_PARPORT=m # # Parallel IDE high-level drivers # CONFIG_PARIDE_PD=m CONFIG_PARIDE_PCD=m CONFIG_PARIDE_PF=m CONFIG_PARIDE_PT=m CONFIG_PARIDE_PG=m # # Parallel IDE protocol modules # CONFIG_PARIDE_ATEN=m CONFIG_PARIDE_BPCK=m # CONFIG_PARIDE_BPCK6 is not set CONFIG_PARIDE_COMM=m CONFIG_PARIDE_DSTR=m CONFIG_PARIDE_FIT2=m CONFIG_PARIDE_FIT3=m CONFIG_PARIDE_EPAT=m CONFIG_PARIDE_EPATC8=y CONFIG_PARIDE_EPIA=m CONFIG_PARIDE_FRIQ=m CONFIG_PARIDE_FRPW=m CONFIG_PARIDE_KBIC=m CONFIG_PARIDE_KTTI=m CONFIG_PARIDE_ON20=m CONFIG_PARIDE_ON26=m CONFIG_BLK_CPQ_DA=m CONFIG_BLK_CPQ_CISS_DA=m CONFIG_CISS_SCSI_TAPE=y CONFIG_BLK_DEV_DAC960=m CONFIG_BLK_DEV_UMEM=m # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=m CONFIG_BLK_DEV_CRYPTOLOOP=m CONFIG_BLK_DEV_NBD=m CONFIG_BLK_DEV_SX8=m CONFIG_BLK_DEV_UB=m CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=16384 CONFIG_BLK_DEV_RAM_BLOCKSIZE=4096 CONFIG_BLK_DEV_INITRD=y CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set CONFIG_ATA_OVER_ETH=m # # Misc devices # # CONFIG_IBM_ASM is not set # CONFIG_SGI_IOC4 is not set # CONFIG_TIFM_CORE is not set # # ATA/ATAPI/MFM/RLL support # CONFIG_IDE=y CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide.txt for help/info on IDE drives # # CONFIG_BLK_DEV_IDE_SATA is not set # CONFIG_BLK_DEV_HD_IDE is not set CONFIG_BLK_DEV_IDEDISK=y CONFIG_IDEDISK_MULTI_MODE=y CONFIG_BLK_DEV_IDECS=m CONFIG_BLK_DEV_IDECD=m # CONFIG_BLK_DEV_IDETAPE is not set CONFIG_BLK_DEV_IDEFLOPPY=y CONFIG_BLK_DEV_IDESCSI=m CONFIG_IDE_TASK_IOCTL=y # # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y # CONFIG_BLK_DEV_CMD640 is not set CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y # CONFIG_BLK_DEV_OFFBOARD is not set CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set # CONFIG_BLK_DEV_RZ1000 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y # CONFIG_BLK_DEV_IDEDMA_FORCED is not set CONFIG_IDEDMA_PCI_AUTO=y # CONFIG_IDEDMA_ONLYDISK is not set CONFIG_BLK_DEV_AEC62XX=y CONFIG_BLK_DEV_ALI15X3=y # CONFIG_WDC_ALI15X3 is not set CONFIG_BLK_DEV_AMD74XX=y CONFIG_BLK_DEV_ATIIXP=y CONFIG_BLK_DEV_CMD64X=y # CONFIG_BLK_DEV_TRIFLEX is not set # CONFIG_BLK_DEV_CY82C693 is not set # CONFIG_BLK_DEV_CS5520 is not set # CONFIG_BLK_DEV_CS5530 is not set # CONFIG_BLK_DEV_CS5535 is not set CONFIG_BLK_DEV_HPT34X=y # CONFIG_HPT34X_AUTODMA is not set CONFIG_BLK_DEV_HPT366=y # CONFIG_BLK_DEV_JMICRON is not set # CONFIG_BLK_DEV_SC1200 is not set CONFIG_BLK_DEV_PIIX=y CONFIG_BLK_DEV_IT821X=y # CONFIG_BLK_DEV_NS87415 is not set CONFIG_BLK_DEV_PDC202XX_OLD=y # CONFIG_PDC202XX_BURST is not set CONFIG_BLK_DEV_PDC202XX_NEW=y CONFIG_BLK_DEV_SVWKS=y CONFIG_BLK_DEV_SIIMAGE=y CONFIG_BLK_DEV_SIS5513=y # CONFIG_BLK_DEV_SLC90E66 is not set # CONFIG_BLK_DEV_TRM290 is not set CONFIG_BLK_DEV_VIA82CXXX=y # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y # CONFIG_IDEDMA_IVB is not set CONFIG_IDEDMA_AUTO=y # CONFIG_BLK_DEV_HD is not set # # SCSI device support # CONFIG_RAID_ATTRS=m CONFIG_SCSI=m CONFIG_SCSI_NETLINK=y CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=m CONFIG_CHR_DEV_ST=m CONFIG_CHR_DEV_OSST=m CONFIG_BLK_DEV_SR=m CONFIG_BLK_DEV_SR_VENDOR=y CONFIG_CHR_DEV_SG=m CONFIG_CHR_DEV_SCH=m # # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y # # SCSI Transports # CONFIG_SCSI_SPI_ATTRS=m CONFIG_SCSI_FC_ATTRS=m CONFIG_SCSI_ISCSI_ATTRS=m CONFIG_SCSI_SAS_ATTRS=m CONFIG_SCSI_SAS_LIBSAS=m # CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set # # SCSI low-level drivers # CONFIG_ISCSI_TCP=m CONFIG_BLK_DEV_3W_XXXX_RAID=m CONFIG_SCSI_3W_9XXX=m CONFIG_SCSI_ACARD=m CONFIG_SCSI_AACRAID=m CONFIG_SCSI_AIC7XXX=m CONFIG_AIC7XXX_CMDS_PER_DEVICE=4 CONFIG_AIC7XXX_RESET_DELAY_MS=15000 # CONFIG_AIC7XXX_DEBUG_ENABLE is not set CONFIG_AIC7XXX_DEBUG_MASK=0 # CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set CONFIG_SCSI_AIC7XXX_OLD=m CONFIG_SCSI_AIC79XX=m CONFIG_AIC79XX_CMDS_PER_DEVICE=4 CONFIG_AIC79XX_RESET_DELAY_MS=15000 # CONFIG_AIC79XX_ENABLE_RD_STRM is not set # CONFIG_AIC79XX_DEBUG_ENABLE is not set CONFIG_AIC79XX_DEBUG_MASK=0 # CONFIG_AIC79XX_REG_PRETTY_PRINT is not set CONFIG_SCSI_AIC94XX=m # CONFIG_AIC94XX_DEBUG is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set CONFIG_MEGARAID_NEWGEN=y CONFIG_MEGARAID_MM=m CONFIG_MEGARAID_MAILBOX=m CONFIG_MEGARAID_LEGACY=m CONFIG_MEGARAID_SAS=m CONFIG_SCSI_HPTIOP=m CONFIG_SCSI_BUSLOGIC=m # CONFIG_SCSI_OMIT_FLASHPOINT is not set # CONFIG_SCSI_DMX3191D is not set # CONFIG_SCSI_EATA is not set # CONFIG_SCSI_FUTURE_DOMAIN is not set CONFIG_SCSI_GDTH=m CONFIG_SCSI_IPS=m CONFIG_SCSI_INITIO=m CONFIG_SCSI_INIA100=m CONFIG_SCSI_PPA=m CONFIG_SCSI_IMM=m # CONFIG_SCSI_IZIP_EPP16 is not set # CONFIG_SCSI_IZIP_SLOW_CTR is not set # CONFIG_SCSI_STEX is not set CONFIG_SCSI_SYM53C8XX_2=m CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1 CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16 CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64 CONFIG_SCSI_SYM53C8XX_MMIO=y # CONFIG_SCSI_IPR is not set CONFIG_SCSI_QLOGIC_1280=m CONFIG_SCSI_QLA_FC=m CONFIG_SCSI_QLA_ISCSI=m CONFIG_SCSI_LPFC=m CONFIG_SCSI_DC395x=m CONFIG_SCSI_DC390T=m # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set # # PCMCIA SCSI adapter support # # CONFIG_PCMCIA_AHA152X is not set # CONFIG_PCMCIA_FDOMAIN is not set # CONFIG_PCMCIA_NINJA_SCSI is not set CONFIG_PCMCIA_QLOGIC=m CONFIG_PCMCIA_SYM53C500=m # # Serial ATA (prod) and Parallel ATA (experimental) drivers # CONFIG_ATA=m CONFIG_SATA_AHCI=m CONFIG_SATA_SVW=m CONFIG_ATA_PIIX=m CONFIG_SATA_MV=m CONFIG_SATA_NV=m CONFIG_PDC_ADMA=m CONFIG_SATA_QSTOR=m CONFIG_SATA_PROMISE=m CONFIG_SATA_SX4=m CONFIG_SATA_SIL=m CONFIG_SATA_SIL24=m CONFIG_SATA_SIS=m CONFIG_SATA_ULI=m CONFIG_SATA_VIA=m CONFIG_SATA_VITESSE=m CONFIG_SATA_INTEL_COMBINED=y CONFIG_PATA_ALI=m CONFIG_PATA_AMD=m CONFIG_PATA_ARTOP=m CONFIG_PATA_ATIIXP=m CONFIG_PATA_CMD64X=m CONFIG_PATA_CS5520=m CONFIG_PATA_CS5530=m # CONFIG_PATA_CS5535 is not set CONFIG_PATA_CYPRESS=m CONFIG_PATA_EFAR=m CONFIG_ATA_GENERIC=m CONFIG_PATA_HPT366=m CONFIG_PATA_HPT37X=m CONFIG_PATA_HPT3X2N=m CONFIG_PATA_HPT3X3=m CONFIG_PATA_IT821X=m CONFIG_PATA_JMICRON=m CONFIG_PATA_TRIFLEX=m CONFIG_PATA_MPIIX=m CONFIG_PATA_OLDPIIX=m CONFIG_PATA_NETCELL=m CONFIG_PATA_NS87410=m CONFIG_PATA_OPTI=m CONFIG_PATA_OPTIDMA=m CONFIG_PATA_PCMCIA=m CONFIG_PATA_PDC_OLD=m CONFIG_PATA_RADISYS=m CONFIG_PATA_RZ1000=m CONFIG_PATA_SC1200=m CONFIG_PATA_SERVERWORKS=m CONFIG_PATA_PDC2027X=m CONFIG_PATA_SIL680=m CONFIG_PATA_SIS=m CONFIG_PATA_VIA=m CONFIG_PATA_WINBOND=m # # Multi-device support (RAID and LVM) # CONFIG_MD=y CONFIG_BLK_DEV_MD=y CONFIG_MD_LINEAR=m CONFIG_MD_RAID0=m CONFIG_MD_RAID1=m CONFIG_MD_RAID10=m CONFIG_MD_RAID456=m CONFIG_MD_RAID5_RESHAPE=y CONFIG_MD_MULTIPATH=m CONFIG_MD_FAULTY=m CONFIG_BLK_DEV_DM=m # CONFIG_DM_DEBUG is not set CONFIG_DM_CRYPT=m CONFIG_DM_SNAPSHOT=m CONFIG_DM_MIRROR=m CONFIG_DM_ZERO=m CONFIG_DM_MULTIPATH=m CONFIG_DM_MULTIPATH_EMC=m # # Fusion MPT device support # CONFIG_FUSION=y CONFIG_FUSION_SPI=m CONFIG_FUSION_FC=m CONFIG_FUSION_SAS=m CONFIG_FUSION_MAX_SGE=40 CONFIG_FUSION_CTL=m CONFIG_FUSION_LAN=m # # IEEE 1394 (FireWire) support # CONFIG_IEEE1394=m # # Subsystem Options # # CONFIG_IEEE1394_VERBOSEDEBUG is not set CONFIG_IEEE1394_OUI_DB=y CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y CONFIG_IEEE1394_CONFIG_ROM_IP1394=y # CONFIG_IEEE1394_EXPORT_FULL_API is not set # # Device Drivers # CONFIG_IEEE1394_PCILYNX=m CONFIG_IEEE1394_OHCI1394=m # # Protocol Drivers # CONFIG_IEEE1394_VIDEO1394=m CONFIG_IEEE1394_SBP2=m # CONFIG_IEEE1394_SBP2_PHYS_DMA is not set CONFIG_IEEE1394_ETH1394=m CONFIG_IEEE1394_DV1394=m CONFIG_IEEE1394_RAWIO=m # # I2O device support # CONFIG_I2O=m # CONFIG_I2O_LCT_NOTIFY_ON_CHANGES is not set CONFIG_I2O_EXT_ADAPTEC=y CONFIG_I2O_CONFIG=m CONFIG_I2O_CONFIG_OLD_IOCTL=y CONFIG_I2O_BUS=m CONFIG_I2O_BLOCK=m CONFIG_I2O_SCSI=m CONFIG_I2O_PROC=m # # Network device support # CONFIG_NETDEVICES=y CONFIG_IFB=m CONFIG_DUMMY=m CONFIG_BONDING=m CONFIG_EQUALIZER=m CONFIG_TUN=m # # ARCnet devices # # CONFIG_ARCNET is not set # # PHY device support # CONFIG_PHYLIB=m # # MII PHY device drivers # CONFIG_MARVELL_PHY=m CONFIG_DAVICOM_PHY=m CONFIG_QSEMI_PHY=m CONFIG_LXT_PHY=m CONFIG_CICADA_PHY=m CONFIG_VITESSE_PHY=m CONFIG_SMSC_PHY=m CONFIG_FIXED_PHY=m CONFIG_FIXED_MII_10_FDX=y CONFIG_FIXED_MII_100_FDX=y # # Ethernet (10 or 100Mbit) # CONFIG_NET_ETHERNET=y CONFIG_MII=m CONFIG_HAPPYMEAL=m CONFIG_SUNGEM=m CONFIG_CASSINI=m CONFIG_NET_VENDOR_3COM=y CONFIG_VORTEX=m CONFIG_TYPHOON=m # # Tulip family network device support # CONFIG_NET_TULIP=y CONFIG_DE2104X=m CONFIG_TULIP=m # CONFIG_TULIP_MWI is not set CONFIG_TULIP_MMIO=y # CONFIG_TULIP_NAPI is not set CONFIG_DE4X5=m CONFIG_WINBOND_840=m CONFIG_DM9102=m CONFIG_ULI526X=m CONFIG_PCMCIA_XIRCOM=m # CONFIG_HP100 is not set CONFIG_NET_PCI=y CONFIG_PCNET32=m # CONFIG_PCNET32_NAPI is not set CONFIG_AMD8111_ETH=m CONFIG_AMD8111E_NAPI=y CONFIG_ADAPTEC_STARFIRE=m CONFIG_ADAPTEC_STARFIRE_NAPI=y CONFIG_B44=m CONFIG_FORCEDETH=m # CONFIG_FORCEDETH_NAPI is not set # CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set CONFIG_E100=m CONFIG_FEALNX=m CONFIG_NATSEMI=m CONFIG_NE2K_PCI=m CONFIG_8139CP=m CONFIG_8139TOO=m # CONFIG_8139TOO_PIO is not set # CONFIG_8139TOO_TUNE_TWISTER is not set CONFIG_8139TOO_8129=y # CONFIG_8139_OLD_RX_RESET is not set CONFIG_SIS900=m CONFIG_EPIC100=m CONFIG_SUNDANCE=m # CONFIG_SUNDANCE_MMIO is not set # CONFIG_TLAN is not set CONFIG_VIA_RHINE=m CONFIG_VIA_RHINE_MMIO=y CONFIG_VIA_RHINE_NAPI=y CONFIG_NET_POCKET=y CONFIG_ATP=m CONFIG_DE600=m CONFIG_DE620=m # # Ethernet (1000 Mbit) # CONFIG_ACENIC=m # CONFIG_ACENIC_OMIT_TIGON_I is not set CONFIG_DL2K=m CONFIG_E1000=m CONFIG_E1000_NAPI=y # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set CONFIG_NS83820=m CONFIG_HAMACHI=m CONFIG_YELLOWFIN=m CONFIG_R8169=m CONFIG_R8169_NAPI=y CONFIG_R8169_VLAN=y CONFIG_SIS190=m CONFIG_SKGE=m CONFIG_SKY2=m # CONFIG_SK98LIN is not set CONFIG_VIA_VELOCITY=m CONFIG_TIGON3=m CONFIG_BNX2=m # CONFIG_QLA3XXX is not set # # Ethernet (10000 Mbit) # CONFIG_CHELSIO_T1=m CONFIG_IXGB=m CONFIG_IXGB_NAPI=y CONFIG_S2IO=m CONFIG_S2IO_NAPI=y CONFIG_MYRI10GE=m # # Token Ring devices # CONFIG_TR=y CONFIG_IBMOL=m # CONFIG_IBMLS is not set CONFIG_3C359=m # CONFIG_TMS380TR is not set # # Wireless LAN (non-hamradio) # CONFIG_NET_RADIO=y CONFIG_NET_WIRELESS_RTNETLINK=y # # Obsolete Wireless cards support (pre-802.11) # # CONFIG_STRIP is not set CONFIG_PCMCIA_WAVELAN=m CONFIG_PCMCIA_NETWAVE=m # # Wireless 802.11 Frequency Hopping cards support # # CONFIG_PCMCIA_RAYCS is not set # # Wireless 802.11b ISA/PCI cards support # CONFIG_IPW2100=m CONFIG_IPW2100_MONITOR=y # CONFIG_IPW2100_DEBUG is not set CONFIG_IPW2200=m CONFIG_IPW2200_MONITOR=y CONFIG_IPW2200_RADIOTAP=y CONFIG_IPW2200_PROMISCUOUS=y CONFIG_IPW2200_QOS=y # CONFIG_IPW2200_DEBUG is not set CONFIG_AIRO=m CONFIG_HERMES=m CONFIG_PLX_HERMES=m CONFIG_TMD_HERMES=m CONFIG_NORTEL_HERMES=m CONFIG_PCI_HERMES=m CONFIG_ATMEL=m CONFIG_PCI_ATMEL=m # # Wireless 802.11b Pcmcia/Cardbus cards support # CONFIG_PCMCIA_HERMES=m CONFIG_PCMCIA_SPECTRUM=m CONFIG_AIRO_CS=m CONFIG_PCMCIA_ATMEL=m CONFIG_PCMCIA_WL3501=m # # Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support # CONFIG_PRISM54=m CONFIG_USB_ZD1201=m CONFIG_HOSTAP=m CONFIG_HOSTAP_FIRMWARE=y CONFIG_HOSTAP_FIRMWARE_NVRAM=y CONFIG_HOSTAP_PLX=m CONFIG_HOSTAP_PCI=m CONFIG_HOSTAP_CS=m CONFIG_BCM43XX=m CONFIG_BCM43XX_DEBUG=y CONFIG_BCM43XX_DMA=y CONFIG_BCM43XX_PIO=y CONFIG_BCM43XX_DMA_AND_PIO_MODE=y # CONFIG_BCM43XX_DMA_MODE is not set # CONFIG_BCM43XX_PIO_MODE is not set CONFIG_ZD1211RW=m # CONFIG_ZD1211RW_DEBUG is not set CONFIG_NET_WIRELESS=y # # PCMCIA network device support # CONFIG_NET_PCMCIA=y CONFIG_PCMCIA_3C589=m CONFIG_PCMCIA_3C574=m CONFIG_PCMCIA_FMVJ18X=m CONFIG_PCMCIA_PCNET=m CONFIG_PCMCIA_NMCLAN=m CONFIG_PCMCIA_SMC91C92=m CONFIG_PCMCIA_XIRC2PS=m CONFIG_PCMCIA_AXNET=m # CONFIG_PCMCIA_IBMTR is not set # # Wan interfaces # # CONFIG_WAN is not set # # ATM drivers # # CONFIG_ATM_DUMMY is not set CONFIG_ATM_TCP=m CONFIG_ATM_LANAI=m CONFIG_ATM_ENI=m # CONFIG_ATM_ENI_DEBUG is not set # CONFIG_ATM_ENI_TUNE_BURST is not set CONFIG_ATM_FIRESTREAM=m # CONFIG_ATM_ZATM is not set # CONFIG_ATM_NICSTAR is not set CONFIG_ATM_IDT77252=m # CONFIG_ATM_IDT77252_DEBUG is not set # CONFIG_ATM_IDT77252_RCV_ALL is not set CONFIG_ATM_IDT77252_USE_SUNI=y CONFIG_ATM_AMBASSADOR=m # CONFIG_ATM_AMBASSADOR_DEBUG is not set CONFIG_ATM_HORIZON=m # CONFIG_ATM_HORIZON_DEBUG is not set # CONFIG_ATM_IA is not set CONFIG_ATM_FORE200E_MAYBE=m # CONFIG_ATM_FORE200E_PCA is not set CONFIG_ATM_HE=m # CONFIG_ATM_HE_USE_SUNI is not set CONFIG_FDDI=y # CONFIG_DEFXX is not set CONFIG_SKFP=m # CONFIG_HIPPI is not set CONFIG_PLIP=m CONFIG_PPP=m CONFIG_PPP_MULTILINK=y CONFIG_PPP_FILTER=y CONFIG_PPP_ASYNC=m CONFIG_PPP_SYNC_TTY=m CONFIG_PPP_DEFLATE=m # CONFIG_PPP_BSDCOMP is not set CONFIG_PPP_MPPE=m CONFIG_PPPOE=m CONFIG_PPPOATM=m CONFIG_SLIP=m CONFIG_SLIP_COMPRESSED=y CONFIG_SLHC=m CONFIG_SLIP_SMART=y # CONFIG_SLIP_MODE_SLIP6 is not set CONFIG_NET_FC=y # CONFIG_SHAPER is not set CONFIG_NETCONSOLE=m CONFIG_NETPOLL=y # CONFIG_NETPOLL_RX is not set CONFIG_NETPOLL_TRAP=y CONFIG_NET_POLL_CONTROLLER=y # # ISDN subsystem # # CONFIG_ISDN is not set # # Telephony Support # # CONFIG_PHONE is not set # # Input device support # CONFIG_INPUT=y CONFIG_INPUT_FF_MEMLESS=y # # Userland interfaces # CONFIG_INPUT_MOUSEDEV=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 CONFIG_INPUT_JOYDEV=m # CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y CONFIG_MOUSE_SERIAL=m CONFIG_MOUSE_VSXXXAA=m CONFIG_INPUT_JOYSTICK=y CONFIG_JOYSTICK_ANALOG=m CONFIG_JOYSTICK_A3D=m CONFIG_JOYSTICK_ADI=m CONFIG_JOYSTICK_COBRA=m CONFIG_JOYSTICK_GF2K=m CONFIG_JOYSTICK_GRIP=m CONFIG_JOYSTICK_GRIP_MP=m CONFIG_JOYSTICK_GUILLEMOT=m CONFIG_JOYSTICK_INTERACT=m CONFIG_JOYSTICK_SIDEWINDER=m CONFIG_JOYSTICK_TMDC=m CONFIG_JOYSTICK_IFORCE=m CONFIG_JOYSTICK_IFORCE_USB=y CONFIG_JOYSTICK_IFORCE_232=y CONFIG_JOYSTICK_WARRIOR=m CONFIG_JOYSTICK_MAGELLAN=m CONFIG_JOYSTICK_SPACEORB=m CONFIG_JOYSTICK_SPACEBALL=m CONFIG_JOYSTICK_STINGER=m CONFIG_JOYSTICK_TWIDJOY=m CONFIG_JOYSTICK_DB9=m CONFIG_JOYSTICK_GAMECON=m CONFIG_JOYSTICK_TURBOGRAFX=m CONFIG_JOYSTICK_JOYDUMP=m CONFIG_INPUT_TOUCHSCREEN=y CONFIG_TOUCHSCREEN_GUNZE=m CONFIG_TOUCHSCREEN_ELO=m CONFIG_TOUCHSCREEN_MTOUCH=m CONFIG_TOUCHSCREEN_MK712=m # CONFIG_TOUCHSCREEN_PENMOUNT is not set # CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set # CONFIG_TOUCHSCREEN_TOUCHWIN is not set CONFIG_INPUT_MISC=y CONFIG_INPUT_PCSPKR=m # CONFIG_INPUT_WISTRON_BTNS is not set CONFIG_INPUT_UINPUT=m # # Hardware I/O ports # CONFIG_SERIO=y CONFIG_SERIO_I8042=y CONFIG_SERIO_SERPORT=y # CONFIG_SERIO_CT82C710 is not set # CONFIG_SERIO_PARKBD is not set # CONFIG_SERIO_PCIPS2 is not set CONFIG_SERIO_LIBPS2=y CONFIG_SERIO_RAW=m CONFIG_GAMEPORT=m CONFIG_GAMEPORT_NS558=m CONFIG_GAMEPORT_L4=m CONFIG_GAMEPORT_EMU10K1=m CONFIG_GAMEPORT_FM801=m # # Character devices # CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y CONFIG_SERIAL_NONSTANDARD=y # CONFIG_COMPUTONE is not set # CONFIG_ROCKETPORT is not set CONFIG_CYCLADES=m # CONFIG_CYZ_INTR is not set # CONFIG_DIGIEPCA is not set # CONFIG_MOXA_INTELLIO is not set # CONFIG_MOXA_SMARTIO is not set # CONFIG_ISI is not set CONFIG_SYNCLINK=m CONFIG_SYNCLINKMP=m CONFIG_SYNCLINK_GT=m CONFIG_N_HDLC=m # CONFIG_SPECIALIX is not set # CONFIG_SX is not set # CONFIG_RIO is not set # CONFIG_STALDRV is not set # # Serial drivers # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_CS=m CONFIG_SERIAL_8250_NR_UARTS=32 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y CONFIG_SERIAL_8250_DETECT_IRQ=y CONFIG_SERIAL_8250_RSA=y # # Non-8250 serial port support # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_SERIAL_JSM=m CONFIG_UNIX98_PTYS=y # CONFIG_LEGACY_PTYS is not set CONFIG_PRINTER=m CONFIG_LP_CONSOLE=y CONFIG_PPDEV=m CONFIG_TIPAR=m # # IPMI # CONFIG_IPMI_HANDLER=m # CONFIG_IPMI_PANIC_EVENT is not set CONFIG_IPMI_DEVICE_INTERFACE=m CONFIG_IPMI_SI=m CONFIG_IPMI_WATCHDOG=m CONFIG_IPMI_POWEROFF=m # # Watchdog Cards # CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set # # Watchdog Device Drivers # CONFIG_SOFT_WATCHDOG=m # CONFIG_ACQUIRE_WDT is not set # CONFIG_ADVANTECH_WDT is not set CONFIG_ALIM1535_WDT=m CONFIG_ALIM7101_WDT=m # CONFIG_SC520_WDT is not set # CONFIG_EUROTECH_WDT is not set # CONFIG_IB700_WDT is not set CONFIG_IBMASR=m # CONFIG_WAFER_WDT is not set CONFIG_I6300ESB_WDT=m CONFIG_I8XX_TCO=m # CONFIG_ITCO_WDT is not set # CONFIG_SC1200_WDT is not set # CONFIG_60XX_WDT is not set # CONFIG_SBC8360_WDT is not set # CONFIG_CPU5_WDT is not set # CONFIG_SMSC37B787_WDT is not set CONFIG_W83627HF_WDT=m # CONFIG_W83697HF_WDT is not set CONFIG_W83877F_WDT=m CONFIG_W83977F_WDT=m CONFIG_MACHZ_WDT=m # CONFIG_SBC_EPX_C3_WATCHDOG is not set # # PCI-based Watchdog Cards # CONFIG_PCIPCWATCHDOG=m CONFIG_WDTPCI=m CONFIG_WDT_501_PCI=y # # USB-based Watchdog Cards # CONFIG_USBPCWATCHDOG=m CONFIG_HW_RANDOM=y CONFIG_HW_RANDOM_INTEL=m CONFIG_HW_RANDOM_AMD=m # CONFIG_HW_RANDOM_GEODE is not set CONFIG_HW_RANDOM_VIA=y CONFIG_NVRAM=y CONFIG_RTC=y CONFIG_DTLK=m CONFIG_R3964=m # CONFIG_APPLICOM is not set # CONFIG_SONYPI is not set # # Ftape, the floppy tape device driver # CONFIG_AGP=y # CONFIG_AGP_ALI is not set # CONFIG_AGP_ATI is not set # CONFIG_AGP_AMD is not set CONFIG_AGP_AMD64=y CONFIG_AGP_INTEL=y # CONFIG_AGP_NVIDIA is not set CONFIG_AGP_SIS=y # CONFIG_AGP_SWORKS is not set CONFIG_AGP_VIA=y # CONFIG_AGP_EFFICEON is not set CONFIG_DRM=m CONFIG_DRM_TDFX=m CONFIG_DRM_R128=m CONFIG_DRM_RADEON=m CONFIG_DRM_I810=m CONFIG_DRM_I830=m CONFIG_DRM_I915=m CONFIG_DRM_MGA=m CONFIG_DRM_SIS=m CONFIG_DRM_VIA=m CONFIG_DRM_SAVAGE=m # # PCMCIA character devices # # CONFIG_SYNCLINK_CS is not set CONFIG_CARDMAN_4000=m CONFIG_CARDMAN_4040=m CONFIG_MWAVE=m CONFIG_PC8736x_GPIO=m CONFIG_NSC_GPIO=m # CONFIG_CS5535_GPIO is not set # CONFIG_RAW_DRIVER is not set CONFIG_HANGCHECK_TIMER=m # # TPM devices # CONFIG_TCG_TPM=m CONFIG_TCG_ATMEL=m # CONFIG_TELCLOCK is not set # # I2C support # CONFIG_I2C=m CONFIG_I2C_CHARDEV=m # # I2C Algorithms # CONFIG_I2C_ALGOBIT=m CONFIG_I2C_ALGOPCF=m CONFIG_I2C_ALGOPCA=m # # I2C Hardware Bus support # # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set CONFIG_I2C_AMD756=m CONFIG_I2C_AMD756_S4882=m CONFIG_I2C_AMD8111=m CONFIG_I2C_I801=m # CONFIG_I2C_I810 is not set # CONFIG_I2C_PIIX4 is not set CONFIG_I2C_ISA=m CONFIG_I2C_NFORCE2=m # CONFIG_I2C_OCORES is not set CONFIG_I2C_PARPORT=m CONFIG_I2C_PARPORT_LIGHT=m CONFIG_I2C_PROSAVAGE=m CONFIG_I2C_SAVAGE4=m # CONFIG_SCx200_ACB is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set CONFIG_I2C_SIS96X=m CONFIG_I2C_STUB=m CONFIG_I2C_VIA=m CONFIG_I2C_VIAPRO=m CONFIG_I2C_VOODOO3=m CONFIG_I2C_PCA_ISA=m # # Miscellaneous I2C Chip support # CONFIG_SENSORS_DS1337=m CONFIG_SENSORS_DS1374=m CONFIG_SENSORS_EEPROM=m CONFIG_SENSORS_PCF8574=m CONFIG_SENSORS_PCA9539=m CONFIG_SENSORS_PCF8591=m CONFIG_SENSORS_MAX6875=m # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # # SPI support # # CONFIG_SPI is not set # CONFIG_SPI_MASTER is not set # # Dallas's 1-wire bus # # CONFIG_W1 is not set # # Hardware Monitoring support # CONFIG_HWMON=m CONFIG_HWMON_VID=m CONFIG_SENSORS_ABITUGURU=m CONFIG_SENSORS_ADM1021=m CONFIG_SENSORS_ADM1025=m CONFIG_SENSORS_ADM1026=m CONFIG_SENSORS_ADM1031=m CONFIG_SENSORS_ADM9240=m # CONFIG_SENSORS_K8TEMP is not set CONFIG_SENSORS_ASB100=m CONFIG_SENSORS_ATXP1=m CONFIG_SENSORS_DS1621=m CONFIG_SENSORS_F71805F=m CONFIG_SENSORS_FSCHER=m CONFIG_SENSORS_FSCPOS=m CONFIG_SENSORS_GL518SM=m CONFIG_SENSORS_GL520SM=m CONFIG_SENSORS_IT87=m CONFIG_SENSORS_LM63=m CONFIG_SENSORS_LM75=m CONFIG_SENSORS_LM77=m CONFIG_SENSORS_LM78=m CONFIG_SENSORS_LM80=m CONFIG_SENSORS_LM83=m CONFIG_SENSORS_LM85=m CONFIG_SENSORS_LM87=m CONFIG_SENSORS_LM90=m CONFIG_SENSORS_LM92=m CONFIG_SENSORS_MAX1619=m CONFIG_SENSORS_PC87360=m CONFIG_SENSORS_SIS5595=m CONFIG_SENSORS_SMSC47M1=m CONFIG_SENSORS_SMSC47M192=m CONFIG_SENSORS_SMSC47B397=m CONFIG_SENSORS_VIA686A=m # CONFIG_SENSORS_VT1211 is not set CONFIG_SENSORS_VT8231=m CONFIG_SENSORS_W83781D=m CONFIG_SENSORS_W83791D=m CONFIG_SENSORS_W83792D=m CONFIG_SENSORS_W83L785TS=m CONFIG_SENSORS_W83627HF=m CONFIG_SENSORS_W83627EHF=m CONFIG_SENSORS_HDAPS=m # CONFIG_HWMON_DEBUG_CHIP is not set # # Multimedia devices # CONFIG_VIDEO_DEV=m CONFIG_VIDEO_V4L1=y CONFIG_VIDEO_V4L1_COMPAT=y CONFIG_VIDEO_V4L2=y # # Video Capture Adapters # # # Video Capture Adapters # # CONFIG_VIDEO_ADV_DEBUG is not set CONFIG_VIDEO_HELPER_CHIPS_AUTO=y CONFIG_VIDEO_TVAUDIO=m CONFIG_VIDEO_TDA7432=m CONFIG_VIDEO_TDA9840=m CONFIG_VIDEO_TDA9875=m CONFIG_VIDEO_TEA6415C=m CONFIG_VIDEO_TEA6420=m CONFIG_VIDEO_MSP3400=m CONFIG_VIDEO_WM8775=m CONFIG_VIDEO_BT819=m CONFIG_VIDEO_BT856=m CONFIG_VIDEO_KS0127=m CONFIG_VIDEO_SAA7110=m CONFIG_VIDEO_SAA7111=m CONFIG_VIDEO_SAA7114=m CONFIG_VIDEO_SAA711X=m CONFIG_VIDEO_TVP5150=m CONFIG_VIDEO_VPX3220=m CONFIG_VIDEO_CX25840=m CONFIG_VIDEO_CX2341X=m CONFIG_VIDEO_SAA7185=m CONFIG_VIDEO_ADV7170=m CONFIG_VIDEO_ADV7175=m # CONFIG_VIDEO_VIVI is not set CONFIG_VIDEO_BT848=m CONFIG_VIDEO_SAA6588=m CONFIG_VIDEO_BWQCAM=m CONFIG_VIDEO_CQCAM=m CONFIG_VIDEO_W9966=m CONFIG_VIDEO_CPIA=m CONFIG_VIDEO_CPIA_PP=m CONFIG_VIDEO_CPIA_USB=m CONFIG_VIDEO_CPIA2=m CONFIG_VIDEO_SAA5246A=m CONFIG_VIDEO_SAA5249=m CONFIG_TUNER_3036=m CONFIG_VIDEO_STRADIS=m CONFIG_VIDEO_ZORAN_ZR36060=m CONFIG_VIDEO_ZORAN=m CONFIG_VIDEO_ZORAN_BUZ=m CONFIG_VIDEO_ZORAN_DC10=m CONFIG_VIDEO_ZORAN_DC30=m CONFIG_VIDEO_ZORAN_LML33=m CONFIG_VIDEO_ZORAN_LML33R10=m CONFIG_VIDEO_ZORAN_AVS6EYES=m CONFIG_VIDEO_SAA7134=m CONFIG_VIDEO_SAA7134_ALSA=m CONFIG_VIDEO_MXB=m CONFIG_VIDEO_DPC=m CONFIG_VIDEO_HEXIUM_ORION=m CONFIG_VIDEO_HEXIUM_GEMINI=m CONFIG_VIDEO_CX88=m CONFIG_VIDEO_CX88_ALSA=m CONFIG_VIDEO_CX88_BLACKBIRD=m # # V4L USB devices # CONFIG_VIDEO_PVRUSB2=m # CONFIG_VIDEO_PVRUSB2_29XXX is not set CONFIG_VIDEO_PVRUSB2_24XXX=y CONFIG_VIDEO_PVRUSB2_SYSFS=y # CONFIG_VIDEO_PVRUSB2_DEBUGIFC is not set CONFIG_VIDEO_EM28XX=m CONFIG_VIDEO_USBVIDEO=m CONFIG_USB_VICAM=m CONFIG_USB_IBMCAM=m CONFIG_USB_KONICAWC=m CONFIG_USB_QUICKCAM_MESSENGER=m CONFIG_USB_ET61X251=m CONFIG_VIDEO_OVCAMCHIP=m CONFIG_USB_W9968CF=m CONFIG_USB_OV511=m CONFIG_USB_SE401=m CONFIG_USB_SN9C102=m CONFIG_USB_STV680=m CONFIG_USB_ZC0301=m CONFIG_USB_PWC=m # CONFIG_USB_PWC_DEBUG is not set # # Radio Adapters # CONFIG_RADIO_GEMTEK_PCI=m CONFIG_RADIO_MAXIRADIO=m CONFIG_RADIO_MAESTRO=m CONFIG_USB_DSBR=m # # Digital Video Broadcasting Devices # # CONFIG_DVB is not set CONFIG_VIDEO_SAA7146=m CONFIG_VIDEO_SAA7146_VV=m CONFIG_VIDEO_VIDEOBUF=m CONFIG_VIDEO_TUNER=m CONFIG_VIDEO_BUF=m CONFIG_VIDEO_BTCX=m CONFIG_VIDEO_IR=m CONFIG_VIDEO_TVEEPROM=m # CONFIG_USB_DABUSB is not set # # Graphics support # # CONFIG_FIRMWARE_EDID is not set CONFIG_FB=y CONFIG_FB_DDC=m CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set CONFIG_FB_MODE_HELPERS=y CONFIG_FB_TILEBLITTING=y CONFIG_FB_CIRRUS=m # CONFIG_FB_PM2 is not set # CONFIG_FB_CYBER2000 is not set # CONFIG_FB_ARC is not set # CONFIG_FB_ASILIANT is not set # CONFIG_FB_IMSTT is not set CONFIG_FB_VGA16=m CONFIG_FB_VESA=y # CONFIG_FB_HGA is not set # CONFIG_FB_S1D13XXX is not set CONFIG_FB_NVIDIA=m CONFIG_FB_NVIDIA_I2C=y CONFIG_FB_RIVA=m # CONFIG_FB_RIVA_I2C is not set # CONFIG_FB_RIVA_DEBUG is not set # CONFIG_FB_I810 is not set CONFIG_FB_INTEL=m # CONFIG_FB_INTEL_DEBUG is not set CONFIG_FB_INTEL_I2C=y CONFIG_FB_MATROX=m CONFIG_FB_MATROX_MILLENIUM=y CONFIG_FB_MATROX_MYSTIQUE=y CONFIG_FB_MATROX_G=y CONFIG_FB_MATROX_I2C=m CONFIG_FB_MATROX_MAVEN=m CONFIG_FB_MATROX_MULTIHEAD=y CONFIG_FB_RADEON=m CONFIG_FB_RADEON_I2C=y # CONFIG_FB_RADEON_DEBUG is not set CONFIG_FB_ATY128=m CONFIG_FB_ATY=m CONFIG_FB_ATY_CT=y CONFIG_FB_ATY_GENERIC_LCD=y CONFIG_FB_ATY_GX=y CONFIG_FB_SAVAGE=m CONFIG_FB_SAVAGE_I2C=y CONFIG_FB_SAVAGE_ACCEL=y # CONFIG_FB_SIS is not set CONFIG_FB_NEOMAGIC=m CONFIG_FB_KYRO=m CONFIG_FB_3DFX=m CONFIG_FB_3DFX_ACCEL=y CONFIG_FB_VOODOO1=m # CONFIG_FB_CYBLA is not set CONFIG_FB_TRIDENT=m CONFIG_FB_TRIDENT_ACCEL=y # CONFIG_FB_GEODE is not set # CONFIG_FB_VIRTUAL is not set # # Console display driver support # CONFIG_VGA_CONSOLE=y CONFIG_VGACON_SOFT_SCROLLBACK=y CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64 CONFIG_VIDEO_SELECT=y CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y # # Logo configuration # CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set CONFIG_LOGO_LINUX_CLUT224=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_BACKLIGHT_CLASS_DEVICE=m CONFIG_BACKLIGHT_DEVICE=y CONFIG_LCD_CLASS_DEVICE=m CONFIG_LCD_DEVICE=y # # Sound # CONFIG_SOUND=m # # Advanced Linux Sound Architecture # CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m CONFIG_SND_HWDEP=m CONFIG_SND_RAWMIDI=m CONFIG_SND_SEQUENCER=m CONFIG_SND_SEQ_DUMMY=m CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=m CONFIG_SND_PCM_OSS=m CONFIG_SND_PCM_OSS_PLUGINS=y CONFIG_SND_SEQUENCER_OSS=y CONFIG_SND_RTCTIMER=m CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y CONFIG_SND_DYNAMIC_MINORS=y # CONFIG_SND_SUPPORT_OLD_API is not set CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set # # Generic devices # CONFIG_SND_MPU401_UART=m CONFIG_SND_OPL3_LIB=m CONFIG_SND_VX_LIB=m CONFIG_SND_AC97_CODEC=m CONFIG_SND_AC97_BUS=m CONFIG_SND_DUMMY=m CONFIG_SND_VIRMIDI=m CONFIG_SND_MTPAV=m # CONFIG_SND_MTS64 is not set # CONFIG_SND_SERIAL_U16550 is not set CONFIG_SND_MPU401=m # # PCI devices # CONFIG_SND_AD1889=m CONFIG_SND_ALS300=m CONFIG_SND_ALS4000=m CONFIG_SND_ALI5451=m CONFIG_SND_ATIIXP=m CONFIG_SND_ATIIXP_MODEM=m CONFIG_SND_AU8810=m CONFIG_SND_AU8820=m CONFIG_SND_AU8830=m CONFIG_SND_AZT3328=m CONFIG_SND_BT87X=m # CONFIG_SND_BT87X_OVERCLOCK is not set CONFIG_SND_CA0106=m CONFIG_SND_CMIPCI=m CONFIG_SND_CS4281=m CONFIG_SND_CS46XX=m CONFIG_SND_CS46XX_NEW_DSP=y # CONFIG_SND_CS5535AUDIO is not set CONFIG_SND_DARLA20=m CONFIG_SND_GINA20=m CONFIG_SND_LAYLA20=m CONFIG_SND_DARLA24=m CONFIG_SND_GINA24=m CONFIG_SND_LAYLA24=m CONFIG_SND_MONA=m CONFIG_SND_MIA=m CONFIG_SND_ECHO3G=m CONFIG_SND_INDIGO=m CONFIG_SND_INDIGOIO=m CONFIG_SND_INDIGODJ=m CONFIG_SND_EMU10K1=m CONFIG_SND_EMU10K1X=m CONFIG_SND_ENS1370=m CONFIG_SND_ENS1371=m CONFIG_SND_ES1938=m CONFIG_SND_ES1968=m CONFIG_SND_FM801=m CONFIG_SND_FM801_TEA575X_BOOL=y CONFIG_SND_FM801_TEA575X=m CONFIG_SND_HDA_INTEL=m CONFIG_SND_HDSP=m CONFIG_SND_HDSPM=m CONFIG_SND_ICE1712=m CONFIG_SND_ICE1724=m CONFIG_SND_INTEL8X0=m CONFIG_SND_INTEL8X0M=m CONFIG_SND_KORG1212=m CONFIG_SND_MAESTRO3=m CONFIG_SND_MIXART=m CONFIG_SND_NM256=m CONFIG_SND_PCXHR=m CONFIG_SND_RIPTIDE=m CONFIG_SND_RME32=m CONFIG_SND_RME96=m CONFIG_SND_RME9652=m CONFIG_SND_SONICVIBES=m CONFIG_SND_TRIDENT=m CONFIG_SND_VIA82XX=m CONFIG_SND_VIA82XX_MODEM=m CONFIG_SND_VX222=m CONFIG_SND_YMFPCI=m # CONFIG_SND_AC97_POWER_SAVE is not set # # USB devices # CONFIG_SND_USB_AUDIO=m CONFIG_SND_USB_USX2Y=m # # PCMCIA devices # # CONFIG_SND_VXPOCKET is not set # CONFIG_SND_PDAUDIOCF is not set # # Open Sound System # # CONFIG_SOUND_PRIME is not set # # USB support # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set # # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y # CONFIG_USB_BANDWIDTH is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_OTG is not set # # USB Host Controller Drivers # CONFIG_USB_EHCI_HCD=m CONFIG_USB_EHCI_SPLIT_ISO=y CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_EHCI_TT_NEWSCHED=y CONFIG_USB_ISP116X_HCD=m CONFIG_USB_OHCI_HCD=m # CONFIG_USB_OHCI_BIG_ENDIAN is not set CONFIG_USB_OHCI_LITTLE_ENDIAN=y CONFIG_USB_UHCI_HCD=m CONFIG_USB_SL811_HCD=m CONFIG_USB_SL811_CS=m # # USB Device Class drivers # CONFIG_USB_ACM=m CONFIG_USB_PRINTER=m # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' # # # may also be needed; see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_DEBUG is not set CONFIG_USB_STORAGE_DATAFAB=y CONFIG_USB_STORAGE_FREECOM=y CONFIG_USB_STORAGE_ISD200=y CONFIG_USB_STORAGE_DPCM=y CONFIG_USB_STORAGE_USBAT=y CONFIG_USB_STORAGE_SDDR09=y CONFIG_USB_STORAGE_SDDR55=y CONFIG_USB_STORAGE_JUMPSHOT=y CONFIG_USB_STORAGE_ALAUDA=y # CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set CONFIG_USB_LIBUSUAL=y # # USB Input Devices # CONFIG_USB_HID=y CONFIG_USB_HIDINPUT=y # CONFIG_USB_HIDINPUT_POWERBOOK is not set CONFIG_HID_FF=y CONFIG_HID_PID=y CONFIG_LOGITECH_FF=y CONFIG_THRUSTMASTER_FF=y # CONFIG_ZEROPLUS_FF is not set CONFIG_USB_HIDDEV=y CONFIG_USB_AIPTEK=m CONFIG_USB_WACOM=m CONFIG_USB_ACECAD=m CONFIG_USB_KBTAB=m CONFIG_USB_POWERMATE=m CONFIG_USB_TOUCHSCREEN=m CONFIG_USB_TOUCHSCREEN_EGALAX=y CONFIG_USB_TOUCHSCREEN_PANJIT=y CONFIG_USB_TOUCHSCREEN_3M=y CONFIG_USB_TOUCHSCREEN_ITM=y CONFIG_USB_TOUCHSCREEN_ETURBO=y CONFIG_USB_TOUCHSCREEN_GUNZE=y # CONFIG_USB_YEALINK is not set CONFIG_USB_XPAD=m CONFIG_USB_ATI_REMOTE=m CONFIG_USB_ATI_REMOTE2=m CONFIG_USB_KEYSPAN_REMOTE=m CONFIG_USB_APPLETOUCH=m # # USB Imaging devices # CONFIG_USB_MDC800=m CONFIG_USB_MICROTEK=m # # USB Network Adapters # CONFIG_USB_CATC=m CONFIG_USB_KAWETH=m CONFIG_USB_PEGASUS=m CONFIG_USB_RTL8150=m CONFIG_USB_USBNET_MII=m CONFIG_USB_USBNET=m CONFIG_USB_NET_AX8817X=m CONFIG_USB_NET_CDCETHER=m CONFIG_USB_NET_GL620A=m CONFIG_USB_NET_NET1080=m CONFIG_USB_NET_PLUSB=m # CONFIG_USB_NET_MCS7830 is not set CONFIG_USB_NET_RNDIS_HOST=m CONFIG_USB_NET_CDC_SUBSET=m CONFIG_USB_ALI_M5632=y CONFIG_USB_AN2720=y CONFIG_USB_BELKIN=y CONFIG_USB_ARMLINUX=y CONFIG_USB_EPSON2888=y CONFIG_USB_NET_ZAURUS=m CONFIG_USB_MON=y # # USB port drivers # CONFIG_USB_USS720=m # # USB Serial Converter support # CONFIG_USB_SERIAL=m CONFIG_USB_SERIAL_GENERIC=y # CONFIG_USB_SERIAL_AIRCABLE is not set CONFIG_USB_SERIAL_AIRPRIME=m CONFIG_USB_SERIAL_ARK3116=m CONFIG_USB_SERIAL_BELKIN=m CONFIG_USB_SERIAL_WHITEHEAT=m CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m CONFIG_USB_SERIAL_CP2101=m CONFIG_USB_SERIAL_CYPRESS_M8=m CONFIG_USB_SERIAL_EMPEG=m CONFIG_USB_SERIAL_FTDI_SIO=m CONFIG_USB_SERIAL_FUNSOFT=m CONFIG_USB_SERIAL_VISOR=m CONFIG_USB_SERIAL_IPAQ=m CONFIG_USB_SERIAL_IR=m CONFIG_USB_SERIAL_EDGEPORT=m CONFIG_USB_SERIAL_EDGEPORT_TI=m CONFIG_USB_SERIAL_GARMIN=m CONFIG_USB_SERIAL_IPW=m CONFIG_USB_SERIAL_KEYSPAN_PDA=m CONFIG_USB_SERIAL_KEYSPAN=m CONFIG_USB_SERIAL_KEYSPAN_MPR=y CONFIG_USB_SERIAL_KEYSPAN_USA28=y CONFIG_USB_SERIAL_KEYSPAN_USA28X=y CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y CONFIG_USB_SERIAL_KEYSPAN_USA19=y CONFIG_USB_SERIAL_KEYSPAN_USA18X=y CONFIG_USB_SERIAL_KEYSPAN_USA19W=y CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y CONFIG_USB_SERIAL_KEYSPAN_USA49W=y CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y CONFIG_USB_SERIAL_KLSI=m CONFIG_USB_SERIAL_KOBIL_SCT=m CONFIG_USB_SERIAL_MCT_U232=m # CONFIG_USB_SERIAL_MOS7720 is not set # CONFIG_USB_SERIAL_MOS7840 is not set CONFIG_USB_SERIAL_NAVMAN=m CONFIG_USB_SERIAL_PL2303=m CONFIG_USB_SERIAL_HP4X=m CONFIG_USB_SERIAL_SAFE=m CONFIG_USB_SERIAL_SAFE_PADDED=y CONFIG_USB_SERIAL_SIERRAWIRELESS=m CONFIG_USB_SERIAL_TI=m CONFIG_USB_SERIAL_CYBERJACK=m CONFIG_USB_SERIAL_XIRCOM=m CONFIG_USB_SERIAL_OPTION=m CONFIG_USB_SERIAL_OMNINET=m CONFIG_USB_EZUSB=y # # USB Miscellaneous drivers # CONFIG_USB_EMI62=m CONFIG_USB_EMI26=m # CONFIG_USB_ADUTUX is not set CONFIG_USB_AUERSWALD=m CONFIG_USB_RIO500=m CONFIG_USB_LEGOTOWER=m CONFIG_USB_LCD=m CONFIG_USB_LED=m # CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set # CONFIG_USB_PHIDGET is not set CONFIG_USB_IDMOUSE=m # CONFIG_USB_FTDI_ELAN is not set CONFIG_USB_APPLEDISPLAY=m CONFIG_USB_SISUSBVGA=m CONFIG_USB_SISUSBVGA_CON=y CONFIG_USB_LD=m # CONFIG_USB_TRANCEVIBRATOR is not set CONFIG_USB_TEST=m # # USB DSL modem support # CONFIG_USB_ATM=m CONFIG_USB_SPEEDTOUCH=m CONFIG_USB_CXACRU=m CONFIG_USB_UEAGLEATM=m CONFIG_USB_XUSBATM=m # # USB Gadget Support # # CONFIG_USB_GADGET is not set # # MMC/SD Card support # CONFIG_MMC=m # CONFIG_MMC_DEBUG is not set CONFIG_MMC_BLOCK=m CONFIG_MMC_SDHCI=m CONFIG_MMC_WBSD=m # CONFIG_MMC_TIFM_SD is not set # # LED devices # CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y # # LED drivers # # # LED Triggers # CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=m CONFIG_LEDS_TRIGGER_IDE_DISK=y CONFIG_LEDS_TRIGGER_HEARTBEAT=m # # InfiniBand support # # CONFIG_INFINIBAND is not set # # EDAC - error detection and reporting (RAS) (EXPERIMENTAL) # CONFIG_EDAC=y # # Reporting subsystems # # CONFIG_EDAC_DEBUG is not set CONFIG_EDAC_MM_EDAC=m # CONFIG_EDAC_AMD76X is not set # CONFIG_EDAC_E7XXX is not set CONFIG_EDAC_E752X=m # CONFIG_EDAC_I82875P is not set # CONFIG_EDAC_I82860 is not set # CONFIG_EDAC_R82600 is not set CONFIG_EDAC_POLL=y # # Real Time Clock # CONFIG_RTC_LIB=m CONFIG_RTC_CLASS=m # # RTC interfaces # CONFIG_RTC_INTF_SYSFS=m CONFIG_RTC_INTF_PROC=m CONFIG_RTC_INTF_DEV=m # CONFIG_RTC_INTF_DEV_UIE_EMUL is not set # # RTC drivers # CONFIG_RTC_DRV_X1205=m CONFIG_RTC_DRV_DS1307=m CONFIG_RTC_DRV_DS1553=m CONFIG_RTC_DRV_ISL1208=m CONFIG_RTC_DRV_DS1672=m CONFIG_RTC_DRV_DS1742=m CONFIG_RTC_DRV_PCF8563=m CONFIG_RTC_DRV_PCF8583=m CONFIG_RTC_DRV_RS5C372=m # CONFIG_RTC_DRV_M48T86 is not set # CONFIG_RTC_DRV_TEST is not set CONFIG_RTC_DRV_V3020=m # # DMA Engine support # CONFIG_DMA_ENGINE=y # # DMA Clients # CONFIG_NET_DMA=y # # DMA Devices # CONFIG_INTEL_IOATDMA=m # # File systems # CONFIG_EXT2_FS=y CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y CONFIG_EXT2_FS_SECURITY=y CONFIG_EXT2_FS_XIP=y CONFIG_FS_XIP=y CONFIG_EXT3_FS=m CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=m CONFIG_JBD_DEBUG=y CONFIG_FS_MBCACHE=y CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set CONFIG_REISERFS_PROC_INFO=y CONFIG_REISERFS_FS_XATTR=y CONFIG_REISERFS_FS_POSIX_ACL=y CONFIG_REISERFS_FS_SECURITY=y CONFIG_JFS_FS=m CONFIG_JFS_POSIX_ACL=y CONFIG_JFS_SECURITY=y # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set CONFIG_FS_POSIX_ACL=y CONFIG_XFS_FS=m CONFIG_XFS_QUOTA=y CONFIG_XFS_SECURITY=y CONFIG_XFS_POSIX_ACL=y # CONFIG_XFS_RT is not set CONFIG_GFS2_FS=m CONFIG_GFS2_FS_LOCKING_NOLOCK=m CONFIG_GFS2_FS_LOCKING_DLM=m CONFIG_OCFS2_FS=m # CONFIG_OCFS2_DEBUG_MASKLOG is not set CONFIG_MINIX_FS=m CONFIG_ROMFS_FS=m CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y CONFIG_QUOTA=y # CONFIG_QFMT_V1 is not set CONFIG_QFMT_V2=y CONFIG_QUOTACTL=y CONFIG_DNOTIFY=y CONFIG_AUTOFS_FS=m CONFIG_AUTOFS4_FS=m CONFIG_FUSE_FS=m # # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=y CONFIG_JOLIET=y CONFIG_ZISOFS=y CONFIG_ZISOFS_FS=y CONFIG_UDF_FS=m CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=m CONFIG_MSDOS_FS=m CONFIG_VFAT_FS=m CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="ascii" # CONFIG_NTFS_FS is not set # # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y CONFIG_RAMFS=y CONFIG_CONFIGFS_FS=m # # Miscellaneous filesystems # # CONFIG_ADFS_FS is not set CONFIG_AFFS_FS=m # CONFIG_ECRYPT_FS is not set CONFIG_HFS_FS=m CONFIG_HFSPLUS_FS=m CONFIG_BEFS_FS=m # CONFIG_BEFS_DEBUG is not set CONFIG_BFS_FS=m CONFIG_EFS_FS=m # CONFIG_JFFS_FS is not set CONFIG_JFFS2_FS=m CONFIG_JFFS2_FS_DEBUG=0 CONFIG_JFFS2_FS_WRITEBUFFER=y CONFIG_JFFS2_SUMMARY=y # CONFIG_JFFS2_FS_XATTR is not set # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set CONFIG_JFFS2_ZLIB=y CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set CONFIG_CRAMFS=m CONFIG_VXFS_FS=m # CONFIG_HPFS_FS is not set CONFIG_QNX4FS_FS=m CONFIG_SYSV_FS=m CONFIG_UFS_FS=m # CONFIG_UFS_FS_WRITE is not set # CONFIG_UFS_DEBUG is not set # # Network File Systems # CONFIG_NFS_FS=m CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y CONFIG_NFS_V4=y CONFIG_NFS_DIRECTIO=y CONFIG_NFSD=m CONFIG_NFSD_V2_ACL=y CONFIG_NFSD_V3=y CONFIG_NFSD_V3_ACL=y CONFIG_NFSD_V4=y CONFIG_NFSD_TCP=y CONFIG_LOCKD=m CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=m CONFIG_NFS_ACL_SUPPORT=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=m CONFIG_SUNRPC_GSS=m CONFIG_RPCSEC_GSS_KRB5=m CONFIG_RPCSEC_GSS_SPKM3=m # CONFIG_SMB_FS is not set CONFIG_CIFS=m # CONFIG_CIFS_STATS is not set CONFIG_CIFS_WEAK_PW_HASH=y CONFIG_CIFS_XATTR=y CONFIG_CIFS_POSIX=y # CONFIG_CIFS_DEBUG2 is not set # CONFIG_CIFS_EXPERIMENTAL is not set CONFIG_NCP_FS=m CONFIG_NCPFS_PACKET_SIGNING=y CONFIG_NCPFS_IOCTL_LOCKING=y CONFIG_NCPFS_STRONG=y CONFIG_NCPFS_NFS_NS=y CONFIG_NCPFS_OS2_NS=y CONFIG_NCPFS_SMALLDOS=y CONFIG_NCPFS_NLS=y CONFIG_NCPFS_EXTRAS=y CONFIG_CODA_FS=m # CONFIG_CODA_FS_OLD_API is not set # CONFIG_AFS_FS is not set CONFIG_9P_FS=m # # Partition Types # CONFIG_PARTITION_ADVANCED=y # CONFIG_ACORN_PARTITION is not set CONFIG_OSF_PARTITION=y CONFIG_AMIGA_PARTITION=y # CONFIG_ATARI_PARTITION is not set CONFIG_MAC_PARTITION=y CONFIG_MSDOS_PARTITION=y CONFIG_BSD_DISKLABEL=y CONFIG_MINIX_SUBPARTITION=y CONFIG_SOLARIS_X86_PARTITION=y CONFIG_UNIXWARE_DISKLABEL=y # CONFIG_LDM_PARTITION is not set CONFIG_SGI_PARTITION=y # CONFIG_ULTRIX_PARTITION is not set CONFIG_SUN_PARTITION=y CONFIG_KARMA_PARTITION=y CONFIG_EFI_PARTITION=y # # Native Language Support # CONFIG_NLS=y CONFIG_NLS_DEFAULT="utf8" CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_CODEPAGE_737=m CONFIG_NLS_CODEPAGE_775=m CONFIG_NLS_CODEPAGE_850=m CONFIG_NLS_CODEPAGE_852=m CONFIG_NLS_CODEPAGE_855=m CONFIG_NLS_CODEPAGE_857=m CONFIG_NLS_CODEPAGE_860=m CONFIG_NLS_CODEPAGE_861=m CONFIG_NLS_CODEPAGE_862=m CONFIG_NLS_CODEPAGE_863=m CONFIG_NLS_CODEPAGE_864=m CONFIG_NLS_CODEPAGE_865=m CONFIG_NLS_CODEPAGE_866=m CONFIG_NLS_CODEPAGE_869=m CONFIG_NLS_CODEPAGE_936=m CONFIG_NLS_CODEPAGE_950=m CONFIG_NLS_CODEPAGE_932=m CONFIG_NLS_CODEPAGE_949=m CONFIG_NLS_CODEPAGE_874=m CONFIG_NLS_ISO8859_8=m CONFIG_NLS_CODEPAGE_1250=m CONFIG_NLS_CODEPAGE_1251=m CONFIG_NLS_ASCII=y CONFIG_NLS_ISO8859_1=m CONFIG_NLS_ISO8859_2=m CONFIG_NLS_ISO8859_3=m CONFIG_NLS_ISO8859_4=m CONFIG_NLS_ISO8859_5=m CONFIG_NLS_ISO8859_6=m CONFIG_NLS_ISO8859_7=m CONFIG_NLS_ISO8859_9=m CONFIG_NLS_ISO8859_13=m CONFIG_NLS_ISO8859_14=m CONFIG_NLS_ISO8859_15=m CONFIG_NLS_KOI8_R=m CONFIG_NLS_KOI8_U=m CONFIG_NLS_UTF8=m # # Distributed Lock Manager # CONFIG_DLM=m CONFIG_DLM_DEBUG=y # # Instrumentation Support # CONFIG_PROFILING=y CONFIG_OPROFILE=m CONFIG_KPROBES=y # # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y # CONFIG_PRINTK_TIME is not set CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_IPIPE_DEBUG is not set CONFIG_IPIPE_TRACE_ENABLE_VALUE=0 CONFIG_DEBUG_KERNEL=y CONFIG_LOG_BUF_SHIFT=17 CONFIG_DETECT_SOFTLOCKUP=y CONFIG_SCHEDSTATS=y # CONFIG_DEBUG_SLAB is not set # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set CONFIG_DEBUG_SPINLOCK=y # CONFIG_DEBUG_MUTEXES is not set # CONFIG_DEBUG_RWSEMS is not set # CONFIG_DEBUG_LOCK_ALLOC is not set # CONFIG_PROVE_LOCKING is not set CONFIG_DEBUG_SPINLOCK_SLEEP=y # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y CONFIG_DEBUG_FS=y # CONFIG_DEBUG_VM is not set CONFIG_DEBUG_LIST=y # CONFIG_FRAME_POINTER is not set CONFIG_UNWIND_INFO=y CONFIG_STACK_UNWIND=y # CONFIG_FORCED_INLINING is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_LKDTM is not set CONFIG_EARLY_PRINTK=y CONFIG_DEBUG_STACKOVERFLOW=y # CONFIG_DEBUG_STACK_USAGE is not set CONFIG_DEBUG_RODATA=y # CONFIG_4KSTACKS is not set CONFIG_X86_FIND_SMP_CONFIG=y CONFIG_X86_MPPARSE=y CONFIG_DOUBLEFAULT=y # # Security options # CONFIG_KEYS=y CONFIG_KEYS_DEBUG_PROC_KEYS=y CONFIG_SECURITY=y CONFIG_SECURITY_NETWORK=y # CONFIG_SECURITY_NETWORK_XFRM is not set CONFIG_SECURITY_CAPABILITIES=y # CONFIG_SECURITY_ROOTPLUG is not set CONFIG_SECURITY_SELINUX=y CONFIG_SECURITY_SELINUX_BOOTPARAM=y CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=1 CONFIG_SECURITY_SELINUX_DISABLE=y CONFIG_SECURITY_SELINUX_DEVELOP=y CONFIG_SECURITY_SELINUX_AVC_STATS=y CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE=1 # CONFIG_SECURITY_SELINUX_ENABLE_SECMARK_DEFAULT is not set # CONFIG_SECURITY_SELINUX_POLICYDB_VERSION_MAX is not set # # Cryptographic options # CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=m CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_HMAC=y CONFIG_CRYPTO_NULL=m CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=m CONFIG_CRYPTO_SHA1=y CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m CONFIG_CRYPTO_WP512=m CONFIG_CRYPTO_TGR192=m CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=m CONFIG_CRYPTO_DES=m CONFIG_CRYPTO_BLOWFISH=m CONFIG_CRYPTO_TWOFISH=m CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_TWOFISH_586 is not set CONFIG_CRYPTO_SERPENT=m CONFIG_CRYPTO_AES=m # CONFIG_CRYPTO_AES_586 is not set CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_ANUBIS=m CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=y # CONFIG_CRYPTO_TEST is not set # # Hardware crypto devices # CONFIG_CRYPTO_DEV_PADLOCK=m CONFIG_CRYPTO_DEV_PADLOCK_AES=m CONFIG_CRYPTO_DEV_PADLOCK_SHA=m # # Library routines # CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC32=y CONFIG_LIBCRC32C=y CONFIG_AUDIT_GENERIC=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=m CONFIG_REED_SOLOMON=m CONFIG_REED_SOLOMON_DEC16=y CONFIG_TEXTSEARCH=y CONFIG_TEXTSEARCH_KMP=m CONFIG_TEXTSEARCH_BM=m CONFIG_TEXTSEARCH_FSM=m CONFIG_PLIST=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GENERIC_PENDING_IRQ=y CONFIG_X86_SMP=y CONFIG_X86_HT=y CONFIG_X86_BIOS_REBOOT=y CONFIG_X86_TRAMPOLINE=y CONFIG_KTIME_SCALAR=y ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-07 7:57 ` Eric Noulard @ 2007-02-07 11:28 ` Jan Kiszka 2007-02-07 11:38 ` Jan Kiszka 2007-02-08 15:11 ` Eric Noulard 0 siblings, 2 replies; 19+ messages in thread From: Jan Kiszka @ 2007-02-07 11:28 UTC (permalink / raw) To: Eric Noulard; +Cc: Xenomai help [-- Attachment #1: Type: text/plain, Size: 599 bytes --] Eric Noulard wrote: > 2007/2/6, Jan Kiszka <jan.kiszka@domain.hid>: >> o check if you have MSI enabled, if yes, try to disable it > > Sorry but I don't know what MSI is? > Could you tell me how to check (and may be some > pointer to valuable information which explains what it is)? Your /proc/interrupts output already suggests it: CONFIG_PCI_MSI is set in your config. It's worth trying the disable it, because even plain Linux has problems with certain board/device combinations. But I don't recall if tg3 was recently involved in such, it may still be an ipipe bug here. Jan [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 250 bytes --] ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-07 11:28 ` Jan Kiszka @ 2007-02-07 11:38 ` Jan Kiszka 2007-02-07 14:03 ` Eric Noulard 2007-02-08 15:11 ` Eric Noulard 1 sibling, 1 reply; 19+ messages in thread From: Jan Kiszka @ 2007-02-07 11:38 UTC (permalink / raw) To: Eric Noulard; +Cc: Xenomai help [-- Attachment #1: Type: text/plain, Size: 1144 bytes --] Jan Kiszka wrote: > Eric Noulard wrote: >> 2007/2/6, Jan Kiszka <jan.kiszka@domain.hid>: >>> o check if you have MSI enabled, if yes, try to disable it >> Sorry but I don't know what MSI is? >> Could you tell me how to check (and may be some >> pointer to valuable information which explains what it is)? > > Your /proc/interrupts output already suggests it: CONFIG_PCI_MSI is set > in your config. It's worth trying the disable it, because even plain > Linux has problems with certain board/device combinations. But I don't > recall if tg3 was recently involved in such, it may still be an ipipe > bug here. On the other hand, CONFIG_ACPI is not set which may cause problems on modern systems as well. You only need to disable CONFIG_ACPI_PROCESSOR for hard RT, the rest of ACPI can safely be enabled. Or is it disabled in your vanilla setup as well? Jan > > Jan > > > > ------------------------------------------------------------------------ > > _______________________________________________ > Xenomai-help mailing list > Xenomai-help@domain.hid > https://mail.gna.org/listinfo/xenomai-help [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 250 bytes --] ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-07 11:38 ` Jan Kiszka @ 2007-02-07 14:03 ` Eric Noulard 0 siblings, 0 replies; 19+ messages in thread From: Eric Noulard @ 2007-02-07 14:03 UTC (permalink / raw) To: Jan Kiszka; +Cc: Xenomai help 2007/2/7, Jan Kiszka <jan.kiszka@domain.hid>: > Jan Kiszka wrote: > > Eric Noulard wrote: > >> 2007/2/6, Jan Kiszka <jan.kiszka@domain.hid>: > >>> o check if you have MSI enabled, if yes, try to disable it > >> Sorry but I don't know what MSI is? > >> Could you tell me how to check (and may be some > >> pointer to valuable information which explains what it is)? > > > > Your /proc/interrupts output already suggests it: CONFIG_PCI_MSI is set > > in your config. It is I've checked the .config. Nevertheless it is set in the vanilla config as well. I've seen documentation in kernel source Documentation/MSI-HOWTO.txt so I will read it at least to know in which way it is related to interrupt handling. >> It's worth trying the disable it, because even plain > > Linux has problems with certain board/device combinations. But I don't > > recall if tg3 was recently involved in such, it may still be an ipipe > > bug here. I will try this. > > On the other hand, CONFIG_ACPI is not set which may cause problems on > modern systems as well. I may try that too. Why may this overall non ACPI config cause problem? > You only need to disable CONFIG_ACPI_PROCESSOR > for hard RT, the rest of ACPI can safely be enabled. Or is it disabled > in your vanilla setup as well? My vanilla config has both ACPI and ACPI_PROCESSOR enabled ('y') -- Erk ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-07 11:28 ` Jan Kiszka 2007-02-07 11:38 ` Jan Kiszka @ 2007-02-08 15:11 ` Eric Noulard 2007-02-08 15:32 ` Jan Kiszka 1 sibling, 1 reply; 19+ messages in thread From: Eric Noulard @ 2007-02-08 15:11 UTC (permalink / raw) To: Jan Kiszka; +Cc: Xenomai help [-- Attachment #1: Type: text/plain, Size: 2185 bytes --] 2007/2/7, Jan Kiszka <jan.kiszka@domain.hid>: > > Your /proc/interrupts output already suggests it: CONFIG_PCI_MSI is set > in your config. It's worth trying the disable it, because even plain > Linux has problems with certain board/device combinations. But I don't > recall if tg3 was recently involved in such, it may still be an ipipe > bug here. The same xenomai patched kernel with CONFIG_PCI_MSI disable boots fine with following /proc/interrupt: ========== CPU0 CPU1 0: 2169593 0 IO-APIC-edge timer, rthal_broadcast_timer 1: 2 0 IO-APIC-edge i8042 2: 0 0 XT-PIC-XT cascade 8: 1 0 IO-APIC-edge rtc 12: 4 0 IO-APIC-edge i8042 14: 18945 0 IO-APIC-edge ide0 16: 26920 0 IO-APIC-fasteoi eth0, eth1 20: 12861 0 IO-APIC-fasteoi uhci_hcd:usb1, ehci_hcd:usb4, libata 21: 0 0 IO-APIC-fasteoi uhci_hcd:usb2 22: 10967 0 IO-APIC-fasteoi uhci_hcd:usb3 NMI: 0 0 LOC: 2169430 2169431 ERR: 0 MIS: 0 ========== The former kernel used with kernel boot parameter "nomsi" continues to hang despite the boot parameter for "nomsi". I did go back to http://www.xenomai.org/index.php/FAQs and saw informations about SMI "On some systems, SMI may be involved in thermal throttling of the CPU. Thus, switching it off can cause hardware damage in overheat scenarios." Now I'm lost with those 3 letters acronyms :(( Does SMI has something to do with MSI or not? In both cases (SMI related to MSI or not) How can I know if SMI is used for thermal throttling on my box? I have the same boot problem with cpus=1 and the first kenrel (SMI enabled) (the box hangs on ifup eth0). Now with the "bootable" xenomai-kernel config I go on and give a try to launch xeno-test (with no option at all), and it hangs the box the near the: "cat /proc/xenomai/rtdm/protocol_devices" message Where should I look in order to investigate this hang. I attached the .config corresponding to bootable but hangable kernel. -- Erk [-- Attachment #2: config-2.6.19-xenomai-2.3-noMSI --] [-- Type: application/octet-stream, Size: 64313 bytes --] # # Automatically generated make config: don't edit # Linux kernel version: 2.6.19-xenomai-2.3 # Wed Feb 7 16:25:05 2007 # CONFIG_X86_32=y CONFIG_GENERIC_TIME=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_SEMAPHORE_SLEEPERS=y CONFIG_X86=y CONFIG_MMU=y CONFIG_GENERIC_ISA_DMA=y CONFIG_GENERIC_IOMAP=y CONFIG_GENERIC_HWEIGHT=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y CONFIG_DMI=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # Code maturity level options # CONFIG_EXPERIMENTAL=y CONFIG_LOCK_KERNEL=y CONFIG_INIT_ENV_ARG_LIMIT=32 # # General setup # CONFIG_LOCALVERSION="" # CONFIG_LOCALVERSION_AUTO is not set CONFIG_SWAP=y CONFIG_SYSVIPC=y # CONFIG_IPC_NS is not set CONFIG_POSIX_MQUEUE=y CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set CONFIG_TASKSTATS=y CONFIG_TASK_DELAY_ACCT=y # CONFIG_UTS_NS is not set CONFIG_AUDIT=y CONFIG_AUDITSYSCALL=y CONFIG_IKCONFIG=m CONFIG_IKCONFIG_PROC=y CONFIG_CPUSETS=y CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" CONFIG_CC_OPTIMIZE_FOR_SIZE=y # CONFIG_TASK_XACCT is not set CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_UID16=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set CONFIG_KALLSYMS_EXTRA_PASS=y CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y CONFIG_SLAB=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 # CONFIG_SLOB is not set # # Loadable module support # CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y CONFIG_STOP_MACHINE=y # # Block layer # CONFIG_BLOCK=y CONFIG_LBD=y CONFIG_BLK_DEV_IO_TRACE=y CONFIG_LSF=y # # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y CONFIG_IOSCHED_CFQ=y # CONFIG_DEFAULT_AS is not set # CONFIG_DEFAULT_DEADLINE is not set CONFIG_DEFAULT_CFQ=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="cfq" # # Real-time sub-system # CONFIG_XENOMAI=y CONFIG_XENO_OPT_NUCLEUS=y CONFIG_XENO_OPT_PERVASIVE=y # CONFIG_XENO_OPT_ISHIELD is not set # CONFIG_XENO_OPT_RPIDISABLE is not set CONFIG_XENO_OPT_SECURITY_ACCESS=y CONFIG_XENO_OPT_PIPELINE_HEAD=y CONFIG_XENO_OPT_PIPE=y CONFIG_XENO_OPT_PIPE_NRDEV=32 CONFIG_XENO_OPT_REGISTRY=y CONFIG_XENO_OPT_REGISTRY_NRSLOTS=512 CONFIG_XENO_OPT_SYS_HEAPSZ=128 CONFIG_XENO_OPT_STATS=y # CONFIG_XENO_OPT_DEBUG is not set # # Timing # # CONFIG_XENO_OPT_TIMING_PERIODIC is not set CONFIG_XENO_OPT_TIMING_PERIOD=0 CONFIG_XENO_OPT_TIMING_TIMERLAT=0 CONFIG_XENO_OPT_TIMING_SCHEDLAT=0 # # Scalability # # CONFIG_XENO_OPT_SCALABLE_SCHED is not set CONFIG_XENO_OPT_TIMER_LIST=y # CONFIG_XENO_OPT_TIMER_HEAP is not set # CONFIG_XENO_OPT_TIMER_WHEEL is not set # # Shared interrupts # # CONFIG_XENO_OPT_SHIRQ_LEVEL is not set # CONFIG_XENO_OPT_SHIRQ_EDGE is not set # # Machine # CONFIG_XENO_HW_FPU=y # # NMI watchdog # # CONFIG_XENO_HW_NMI_DEBUG_LATENCY is not set # # SMI workaround # # CONFIG_XENO_HW_SMI_DETECT_DISABLE is not set CONFIG_XENO_HW_SMI_DETECT=y # CONFIG_XENO_HW_SMI_WORKAROUND is not set # # Interfaces # CONFIG_XENO_SKIN_NATIVE=y CONFIG_XENO_OPT_NATIVE_PIPE=y CONFIG_XENO_OPT_NATIVE_PIPE_BUFSZ=4096 CONFIG_XENO_OPT_NATIVE_REGISTRY=y CONFIG_XENO_OPT_NATIVE_SEM=y CONFIG_XENO_OPT_NATIVE_EVENT=y CONFIG_XENO_OPT_NATIVE_MUTEX=y CONFIG_XENO_OPT_NATIVE_COND=y CONFIG_XENO_OPT_NATIVE_QUEUE=y CONFIG_XENO_OPT_NATIVE_HEAP=y CONFIG_XENO_OPT_NATIVE_ALARM=y CONFIG_XENO_OPT_NATIVE_MPS=y # CONFIG_XENO_OPT_NATIVE_INTR is not set CONFIG_XENO_SKIN_POSIX=y CONFIG_XENO_OPT_POSIX_SHM=y # CONFIG_XENO_OPT_POSIX_INTR is not set CONFIG_XENO_OPT_DEBUG_POSIX=y # CONFIG_XENO_SKIN_PSOS is not set # CONFIG_XENO_SKIN_UITRON is not set # CONFIG_XENO_SKIN_VRTX is not set CONFIG_XENO_SKIN_VXWORKS=m # CONFIG_XENO_SKIN_RTAI is not set CONFIG_XENO_SKIN_RTDM=y CONFIG_XENO_OPT_RTDM_FILDES=128 # # Drivers # # # Serial drivers # CONFIG_XENO_DRIVERS_16550A=m # # Testing drivers # CONFIG_XENO_DRIVERS_TIMERBENCH=m CONFIG_XENO_DRIVERS_IRQBENCH=m CONFIG_XENO_DRIVERS_SWITCHTEST=m # # CAN drivers # # CONFIG_XENO_DRIVERS_CAN is not set # # Processor type and features # CONFIG_SMP=y CONFIG_X86_PC=y # CONFIG_X86_ELAN is not set # CONFIG_X86_VOYAGER is not set # CONFIG_X86_NUMAQ is not set # CONFIG_X86_SUMMIT is not set # CONFIG_X86_BIGSMP is not set # CONFIG_X86_VISWS is not set # CONFIG_X86_GENERICARCH is not set # CONFIG_X86_ES7000 is not set # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set # CONFIG_M586TSC is not set # CONFIG_M586MMX is not set CONFIG_M686=y # CONFIG_MPENTIUMII is not set # CONFIG_MPENTIUMIII is not set # CONFIG_MPENTIUMM is not set # CONFIG_MPENTIUM4 is not set # CONFIG_MK6 is not set # CONFIG_MK7 is not set # CONFIG_MK8 is not set # CONFIG_MCRUSOE is not set # CONFIG_MEFFICEON is not set # CONFIG_MWINCHIPC6 is not set # CONFIG_MWINCHIP2 is not set # CONFIG_MWINCHIP3D is not set # CONFIG_MGEODEGX1 is not set # CONFIG_MGEODE_LX is not set # CONFIG_MCYRIXIII is not set # CONFIG_MVIAC3_2 is not set # CONFIG_X86_GENERIC is not set CONFIG_X86_CMPXCHG=y CONFIG_X86_XADD=y CONFIG_X86_L1_CACHE_SHIFT=5 CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_X86_PPRO_FENCE=y CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y CONFIG_X86_CMPXCHG64=y CONFIG_X86_GOOD_APIC=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_TSC=y CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_NR_CPUS=64 CONFIG_SCHED_SMT=y CONFIG_SCHED_MC=y # CONFIG_PREEMPT_NONE is not set CONFIG_PREEMPT_VOLUNTARY=y # CONFIG_PREEMPT is not set CONFIG_PREEMPT_BKL=y CONFIG_IPIPE=y CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y CONFIG_X86_MCE=y # CONFIG_X86_MCE_NONFATAL is not set # CONFIG_X86_MCE_P4THERMAL is not set CONFIG_VM86=y # CONFIG_TOSHIBA is not set # CONFIG_I8K is not set # CONFIG_X86_REBOOTFIXUPS is not set CONFIG_MICROCODE=m CONFIG_MICROCODE_OLD_INTERFACE=y CONFIG_X86_MSR=y CONFIG_X86_CPUID=y # # Firmware Drivers # CONFIG_EDD=m CONFIG_DELL_RBU=m CONFIG_DCDBAS=m CONFIG_NOHIGHMEM=y # CONFIG_HIGHMEM4G is not set # CONFIG_HIGHMEM64G is not set CONFIG_PAGE_OFFSET=0xC0000000 CONFIG_NEED_NODE_MEMMAP_SIZE=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_SPARSEMEM_ENABLE=y CONFIG_ARCH_SELECT_MEMORY_MODEL=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y # CONFIG_FLATMEM_MANUAL is not set # CONFIG_DISCONTIGMEM_MANUAL is not set CONFIG_SPARSEMEM_MANUAL=y CONFIG_SPARSEMEM=y CONFIG_HAVE_MEMORY_PRESENT=y CONFIG_SPARSEMEM_STATIC=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y # CONFIG_MATH_EMULATION is not set CONFIG_MTRR=y CONFIG_IRQBALANCE=y CONFIG_REGPARM=y # CONFIG_SECCOMP is not set # CONFIG_HZ_100 is not set # CONFIG_HZ_250 is not set CONFIG_HZ_1000=y CONFIG_HZ=1000 CONFIG_KEXEC=y CONFIG_PHYSICAL_START=0x100000 CONFIG_HOTPLUG_CPU=y CONFIG_COMPAT_VDSO=y # # Power management options (ACPI, APM) # # CONFIG_PM is not set # # ACPI (Advanced Configuration and Power Interface) Support # # CONFIG_ACPI is not set # # CPU Frequency scaling # # CONFIG_CPU_FREQ is not set # # Bus options (PCI, PCMCIA, EISA, MCA, ISA) # CONFIG_PCI=y # CONFIG_PCI_GOBIOS is not set # CONFIG_PCI_GOMMCONFIG is not set # CONFIG_PCI_GODIRECT is not set CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y CONFIG_PCIEPORTBUS=y CONFIG_HOTPLUG_PCI_PCIE=m # CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE is not set # CONFIG_PCI_MSI is not set # CONFIG_PCI_DEBUG is not set CONFIG_HT_IRQ=y CONFIG_ISA_DMA_API=y # CONFIG_ISA is not set # CONFIG_MCA is not set # CONFIG_SCx200 is not set CONFIG_K8_NB=y # # PCCARD (PCMCIA/CardBus) support # CONFIG_PCCARD=y # CONFIG_PCMCIA_DEBUG is not set CONFIG_PCMCIA=y CONFIG_PCMCIA_LOAD_CIS=y CONFIG_PCMCIA_IOCTL=y CONFIG_CARDBUS=y # # PC-card bridges # CONFIG_YENTA=y CONFIG_YENTA_O2=y CONFIG_YENTA_RICOH=y CONFIG_YENTA_TI=y CONFIG_YENTA_ENE_TUNE=y CONFIG_YENTA_TOSHIBA=y CONFIG_PD6729=m CONFIG_I82092=m CONFIG_PCCARD_NONSTATIC=y # # PCI Hotplug Support # CONFIG_HOTPLUG_PCI=y CONFIG_HOTPLUG_PCI_FAKE=m # CONFIG_HOTPLUG_PCI_COMPAQ is not set # CONFIG_HOTPLUG_PCI_IBM is not set # CONFIG_HOTPLUG_PCI_CPCI is not set CONFIG_HOTPLUG_PCI_SHPC=m # CONFIG_HOTPLUG_PCI_SHPC_POLL_EVENT_MODE is not set # # Executable file formats # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_AOUT is not set CONFIG_BINFMT_MISC=y # # Networking # CONFIG_NET=y # # Networking options # # CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y CONFIG_XFRM=y CONFIG_XFRM_USER=y # CONFIG_XFRM_SUB_POLICY is not set CONFIG_NET_KEY=m CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_ADVANCED_ROUTER=y CONFIG_ASK_IP_FIB_HASH=y # CONFIG_IP_FIB_TRIE is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_MULTIPLE_TABLES=y CONFIG_IP_ROUTE_FWMARK=y CONFIG_IP_ROUTE_MULTIPATH=y # CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set CONFIG_IP_ROUTE_VERBOSE=y # CONFIG_IP_PNP is not set CONFIG_NET_IPIP=m CONFIG_NET_IPGRE=m CONFIG_NET_IPGRE_BROADCAST=y CONFIG_IP_MROUTE=y CONFIG_IP_PIMSM_V1=y CONFIG_IP_PIMSM_V2=y # CONFIG_ARPD is not set CONFIG_SYN_COOKIES=y CONFIG_INET_AH=m CONFIG_INET_ESP=m CONFIG_INET_IPCOMP=m CONFIG_INET_XFRM_TUNNEL=m CONFIG_INET_TUNNEL=m CONFIG_INET_XFRM_MODE_TRANSPORT=m CONFIG_INET_XFRM_MODE_TUNNEL=m CONFIG_INET_XFRM_MODE_BEET=y CONFIG_INET_DIAG=m CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_ADVANCED=y CONFIG_TCP_CONG_BIC=y CONFIG_TCP_CONG_CUBIC=m CONFIG_TCP_CONG_WESTWOOD=m CONFIG_TCP_CONG_HTCP=m CONFIG_TCP_CONG_HSTCP=m CONFIG_TCP_CONG_HYBLA=m CONFIG_TCP_CONG_VEGAS=m CONFIG_TCP_CONG_SCALABLE=m CONFIG_TCP_CONG_LP=m CONFIG_TCP_CONG_VENO=m CONFIG_DEFAULT_BIC=y # CONFIG_DEFAULT_CUBIC is not set # CONFIG_DEFAULT_HTCP is not set # CONFIG_DEFAULT_VEGAS is not set # CONFIG_DEFAULT_WESTWOOD is not set # CONFIG_DEFAULT_RENO is not set CONFIG_DEFAULT_TCP_CONG="bic" # # IP: Virtual Server Configuration # CONFIG_IP_VS=m # CONFIG_IP_VS_DEBUG is not set CONFIG_IP_VS_TAB_BITS=12 # # IPVS transport protocol load balancing support # CONFIG_IP_VS_PROTO_TCP=y CONFIG_IP_VS_PROTO_UDP=y CONFIG_IP_VS_PROTO_ESP=y CONFIG_IP_VS_PROTO_AH=y # # IPVS scheduler # CONFIG_IP_VS_RR=m CONFIG_IP_VS_WRR=m CONFIG_IP_VS_LC=m CONFIG_IP_VS_WLC=m CONFIG_IP_VS_LBLC=m CONFIG_IP_VS_LBLCR=m CONFIG_IP_VS_DH=m CONFIG_IP_VS_SH=m CONFIG_IP_VS_SED=m CONFIG_IP_VS_NQ=m # # IPVS application helper # CONFIG_IP_VS_FTP=m CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y CONFIG_IPV6_ROUTE_INFO=y CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m # CONFIG_IPV6_MIP6 is not set CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_INET6_XFRM_MODE_TRANSPORT=m CONFIG_INET6_XFRM_MODE_TUNNEL=m CONFIG_INET6_XFRM_MODE_BEET=m # CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set CONFIG_IPV6_SIT=m CONFIG_IPV6_TUNNEL=m # CONFIG_IPV6_MULTIPLE_TABLES is not set CONFIG_NETLABEL=y CONFIG_NETWORK_SECMARK=y CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set CONFIG_BRIDGE_NETFILTER=y # # Core Netfilter Configuration # CONFIG_NETFILTER_NETLINK=m CONFIG_NETFILTER_NETLINK_QUEUE=m CONFIG_NETFILTER_NETLINK_LOG=m CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m # CONFIG_NETFILTER_XT_TARGET_DSCP is not set CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_SECMARK=m CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m CONFIG_NETFILTER_XT_MATCH_CONNMARK=m CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m # CONFIG_NETFILTER_XT_MATCH_DSCP is not set CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m CONFIG_NETFILTER_XT_MATCH_POLICY=m CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # # IP: Netfilter Configuration # CONFIG_IP_NF_CONNTRACK=m CONFIG_IP_NF_CT_ACCT=y CONFIG_IP_NF_CONNTRACK_MARK=y CONFIG_IP_NF_CONNTRACK_SECMARK=y CONFIG_IP_NF_CONNTRACK_EVENTS=y CONFIG_IP_NF_CONNTRACK_NETLINK=m CONFIG_IP_NF_CT_PROTO_SCTP=m CONFIG_IP_NF_FTP=m CONFIG_IP_NF_IRC=m CONFIG_IP_NF_NETBIOS_NS=m CONFIG_IP_NF_TFTP=m CONFIG_IP_NF_AMANDA=m CONFIG_IP_NF_PPTP=m CONFIG_IP_NF_H323=m CONFIG_IP_NF_SIP=m CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_IPRANGE=m CONFIG_IP_NF_MATCH_TOS=m CONFIG_IP_NF_MATCH_RECENT=m CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_MATCH_OWNER=m CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_HASHLIMIT=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m CONFIG_IP_NF_TARGET_ULOG=m CONFIG_IP_NF_TARGET_TCPMSS=m CONFIG_IP_NF_NAT=m CONFIG_IP_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m CONFIG_IP_NF_TARGET_SAME=m CONFIG_IP_NF_NAT_SNMP_BASIC=m CONFIG_IP_NF_NAT_IRC=m CONFIG_IP_NF_NAT_FTP=m CONFIG_IP_NF_NAT_TFTP=m CONFIG_IP_NF_NAT_AMANDA=m CONFIG_IP_NF_NAT_PPTP=m CONFIG_IP_NF_NAT_H323=m CONFIG_IP_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m CONFIG_IP_NF_ARP_MANGLE=m # # IPv6: Netfilter Configuration (EXPERIMENTAL) # CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_FRAG=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_OWNER=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_LOG=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m CONFIG_IP6_NF_RAW=m # # DECnet: Netfilter Configuration # # CONFIG_DECNET_NF_GRABULATOR is not set # # Bridge: Netfilter Configuration # CONFIG_BRIDGE_NF_EBTABLES=m CONFIG_BRIDGE_EBT_BROUTE=m CONFIG_BRIDGE_EBT_T_FILTER=m CONFIG_BRIDGE_EBT_T_NAT=m CONFIG_BRIDGE_EBT_802_3=m CONFIG_BRIDGE_EBT_AMONG=m CONFIG_BRIDGE_EBT_ARP=m CONFIG_BRIDGE_EBT_IP=m CONFIG_BRIDGE_EBT_LIMIT=m CONFIG_BRIDGE_EBT_MARK=m CONFIG_BRIDGE_EBT_PKTTYPE=m CONFIG_BRIDGE_EBT_STP=m CONFIG_BRIDGE_EBT_VLAN=m CONFIG_BRIDGE_EBT_ARPREPLY=m CONFIG_BRIDGE_EBT_DNAT=m CONFIG_BRIDGE_EBT_MARK_T=m CONFIG_BRIDGE_EBT_REDIRECT=m CONFIG_BRIDGE_EBT_SNAT=m CONFIG_BRIDGE_EBT_LOG=m CONFIG_BRIDGE_EBT_ULOG=m # # DCCP Configuration (EXPERIMENTAL) # CONFIG_IP_DCCP=m CONFIG_INET_DCCP_DIAG=m CONFIG_IP_DCCP_ACKVEC=y # # DCCP CCIDs Configuration (EXPERIMENTAL) # CONFIG_IP_DCCP_CCID2=m # CONFIG_IP_DCCP_CCID2_DEBUG is not set CONFIG_IP_DCCP_CCID3=m CONFIG_IP_DCCP_TFRC_LIB=m # # DCCP Kernel Hacking # # CONFIG_IP_DCCP_DEBUG is not set # CONFIG_NET_DCCPPROBE is not set # # SCTP Configuration (EXPERIMENTAL) # CONFIG_IP_SCTP=m # CONFIG_SCTP_DBG_MSG is not set # CONFIG_SCTP_DBG_OBJCNT is not set # CONFIG_SCTP_HMAC_NONE is not set # CONFIG_SCTP_HMAC_SHA1 is not set CONFIG_SCTP_HMAC_MD5=y # # TIPC Configuration (EXPERIMENTAL) # CONFIG_TIPC=m # CONFIG_TIPC_ADVANCED is not set # CONFIG_TIPC_DEBUG is not set CONFIG_ATM=m CONFIG_ATM_CLIP=m # CONFIG_ATM_CLIP_NO_ICMP is not set CONFIG_ATM_LANE=m # CONFIG_ATM_MPOA is not set CONFIG_ATM_BR2684=m # CONFIG_ATM_BR2684_IPFILTER is not set CONFIG_BRIDGE=m CONFIG_VLAN_8021Q=m CONFIG_DECNET=m CONFIG_DECNET_ROUTER=y CONFIG_DECNET_ROUTE_FWMARK=y CONFIG_LLC=y # CONFIG_LLC2 is not set CONFIG_IPX=m # CONFIG_IPX_INTERN is not set CONFIG_ATALK=m CONFIG_DEV_APPLETALK=m CONFIG_IPDDP=m CONFIG_IPDDP_ENCAP=y CONFIG_IPDDP_DECAP=y # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_ECONET is not set CONFIG_WAN_ROUTER=m # # QoS and/or fair queueing # CONFIG_NET_SCHED=y # CONFIG_NET_SCH_CLK_JIFFIES is not set CONFIG_NET_SCH_CLK_GETTIMEOFDAY=y # CONFIG_NET_SCH_CLK_CPU is not set # # Queueing/Scheduling # CONFIG_NET_SCH_CBQ=m CONFIG_NET_SCH_HTB=m CONFIG_NET_SCH_HFSC=m CONFIG_NET_SCH_ATM=m CONFIG_NET_SCH_PRIO=m CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m CONFIG_NET_SCH_TBF=m CONFIG_NET_SCH_GRED=m CONFIG_NET_SCH_DSMARK=m CONFIG_NET_SCH_NETEM=m CONFIG_NET_SCH_INGRESS=m # # Classification # CONFIG_NET_CLS=y CONFIG_NET_CLS_BASIC=m CONFIG_NET_CLS_TCINDEX=m CONFIG_NET_CLS_ROUTE4=m CONFIG_NET_CLS_ROUTE=y CONFIG_NET_CLS_FW=m CONFIG_NET_CLS_U32=m CONFIG_CLS_U32_PERF=y CONFIG_CLS_U32_MARK=y CONFIG_NET_CLS_RSVP=m CONFIG_NET_CLS_RSVP6=m CONFIG_NET_EMATCH=y CONFIG_NET_EMATCH_STACK=32 CONFIG_NET_EMATCH_CMP=m CONFIG_NET_EMATCH_NBYTE=m CONFIG_NET_EMATCH_U32=m CONFIG_NET_EMATCH_META=m CONFIG_NET_EMATCH_TEXT=m CONFIG_NET_CLS_ACT=y CONFIG_NET_ACT_POLICE=m CONFIG_NET_ACT_GACT=m CONFIG_GACT_PROB=y CONFIG_NET_ACT_MIRRED=m CONFIG_NET_ACT_IPT=m CONFIG_NET_ACT_PEDIT=m CONFIG_NET_ACT_SIMP=m CONFIG_NET_CLS_IND=y CONFIG_NET_ESTIMATOR=y # # Network testing # CONFIG_NET_PKTGEN=m # CONFIG_NET_TCPPROBE is not set # CONFIG_HAMRADIO is not set CONFIG_IRDA=m # # IrDA protocols # CONFIG_IRLAN=m CONFIG_IRNET=m CONFIG_IRCOMM=m # CONFIG_IRDA_ULTRA is not set # # IrDA options # CONFIG_IRDA_CACHE_LAST_LSAP=y CONFIG_IRDA_FAST_RR=y # CONFIG_IRDA_DEBUG is not set # # Infrared-port device drivers # # # SIR device drivers # CONFIG_IRTTY_SIR=m # # Dongle support # CONFIG_DONGLE=y CONFIG_ESI_DONGLE=m CONFIG_ACTISYS_DONGLE=m CONFIG_TEKRAM_DONGLE=m CONFIG_TOIM3232_DONGLE=m CONFIG_LITELINK_DONGLE=m CONFIG_MA600_DONGLE=m CONFIG_GIRBIL_DONGLE=m CONFIG_MCP2120_DONGLE=m CONFIG_OLD_BELKIN_DONGLE=m CONFIG_ACT200L_DONGLE=m # # Old SIR device drivers # # # Old Serial dongle support # # # FIR device drivers # CONFIG_USB_IRDA=m CONFIG_SIGMATEL_FIR=m CONFIG_NSC_FIR=m CONFIG_WINBOND_FIR=m # CONFIG_TOSHIBA_FIR is not set CONFIG_SMC_IRCC_FIR=m CONFIG_ALI_FIR=m CONFIG_VLSI_FIR=m CONFIG_VIA_FIR=m CONFIG_MCS_FIR=m CONFIG_BT=m CONFIG_BT_L2CAP=m CONFIG_BT_SCO=m CONFIG_BT_RFCOMM=m CONFIG_BT_RFCOMM_TTY=y CONFIG_BT_BNEP=m CONFIG_BT_BNEP_MC_FILTER=y CONFIG_BT_BNEP_PROTO_FILTER=y CONFIG_BT_HIDP=m # # Bluetooth device drivers # CONFIG_BT_HCIUSB=m CONFIG_BT_HCIUSB_SCO=y CONFIG_BT_HCIUART=m CONFIG_BT_HCIUART_H4=y CONFIG_BT_HCIUART_BCSP=y CONFIG_BT_HCIBCM203X=m CONFIG_BT_HCIBPA10X=m CONFIG_BT_HCIBFUSB=m CONFIG_BT_HCIDTL1=m CONFIG_BT_HCIBT3C=m CONFIG_BT_HCIBLUECARD=m CONFIG_BT_HCIBTUART=m CONFIG_BT_HCIVHCI=m CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m CONFIG_IEEE80211_CRYPT_TKIP=m CONFIG_IEEE80211_SOFTMAC=m CONFIG_IEEE80211_SOFTMAC_DEBUG=y CONFIG_WIRELESS_EXT=y CONFIG_FIB_RULES=y # # Device Drivers # # # Generic Driver Options # CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y # CONFIG_DEBUG_DRIVER is not set # CONFIG_SYS_HYPERVISOR is not set # # Connector - unified userspace <-> kernelspace linker # CONFIG_CONNECTOR=y CONFIG_PROC_EVENTS=y # # Memory Technology Devices (MTD) # CONFIG_MTD=m # CONFIG_MTD_DEBUG is not set CONFIG_MTD_CONCAT=m CONFIG_MTD_PARTITIONS=y CONFIG_MTD_REDBOOT_PARTS=m CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1 # CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set # CONFIG_MTD_REDBOOT_PARTS_READONLY is not set # # User Modules And Translation Layers # CONFIG_MTD_CHAR=m CONFIG_MTD_BLOCK=m CONFIG_MTD_BLOCK_RO=m CONFIG_FTL=m CONFIG_NFTL=m CONFIG_NFTL_RW=y CONFIG_INFTL=m CONFIG_RFD_FTL=m # CONFIG_SSFDC is not set # # RAM/ROM/Flash chip drivers # CONFIG_MTD_CFI=m CONFIG_MTD_JEDECPROBE=m CONFIG_MTD_GEN_PROBE=m # CONFIG_MTD_CFI_ADV_OPTIONS is not set CONFIG_MTD_MAP_BANK_WIDTH_1=y CONFIG_MTD_MAP_BANK_WIDTH_2=y CONFIG_MTD_MAP_BANK_WIDTH_4=y # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set CONFIG_MTD_CFI_I1=y CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I4 is not set # CONFIG_MTD_CFI_I8 is not set CONFIG_MTD_CFI_INTELEXT=m CONFIG_MTD_CFI_AMDSTD=m CONFIG_MTD_CFI_STAA=m CONFIG_MTD_CFI_UTIL=m CONFIG_MTD_RAM=m CONFIG_MTD_ROM=m CONFIG_MTD_ABSENT=m # CONFIG_MTD_OBSOLETE_CHIPS is not set # # Mapping drivers for chip access # CONFIG_MTD_COMPLEX_MAPPINGS=y # CONFIG_MTD_PHYSMAP is not set # CONFIG_MTD_PNC2000 is not set CONFIG_MTD_SC520CDP=m CONFIG_MTD_NETSC520=m CONFIG_MTD_TS5500=m # CONFIG_MTD_SBC_GXX is not set # CONFIG_MTD_AMD76XROM is not set # CONFIG_MTD_ICHXROM is not set CONFIG_MTD_SCB2_FLASH=m # CONFIG_MTD_NETtel is not set # CONFIG_MTD_DILNETPC is not set # CONFIG_MTD_L440GX is not set CONFIG_MTD_PCI=m # CONFIG_MTD_PLATRAM is not set # # Self-contained MTD device drivers # CONFIG_MTD_PMC551=m # CONFIG_MTD_PMC551_BUGFIX is not set # CONFIG_MTD_PMC551_DEBUG is not set # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set CONFIG_MTD_MTDRAM=m CONFIG_MTDRAM_TOTAL_SIZE=4096 CONFIG_MTDRAM_ERASE_SIZE=128 CONFIG_MTD_BLOCK2MTD=m # # Disk-On-Chip Device Drivers # # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set # # NAND Flash Device Drivers # CONFIG_MTD_NAND=m # CONFIG_MTD_NAND_VERIFY_WRITE is not set CONFIG_MTD_NAND_ECC_SMC=y CONFIG_MTD_NAND_IDS=m CONFIG_MTD_NAND_DISKONCHIP=m # CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0 # CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set # CONFIG_MTD_NAND_CS553X is not set CONFIG_MTD_NAND_NANDSIM=m # # OneNAND Flash Device Drivers # # CONFIG_MTD_ONENAND is not set # # Parallel port support # CONFIG_PARPORT=m CONFIG_PARPORT_PC=m CONFIG_PARPORT_SERIAL=m # CONFIG_PARPORT_PC_FIFO is not set # CONFIG_PARPORT_PC_SUPERIO is not set CONFIG_PARPORT_PC_PCMCIA=m CONFIG_PARPORT_NOT_PC=y # CONFIG_PARPORT_GSC is not set # CONFIG_PARPORT_AX88796 is not set CONFIG_PARPORT_1284=y # # Plug and Play support # # # Block devices # CONFIG_BLK_DEV_FD=m CONFIG_PARIDE=m CONFIG_PARIDE_PARPORT=m # # Parallel IDE high-level drivers # CONFIG_PARIDE_PD=m CONFIG_PARIDE_PCD=m CONFIG_PARIDE_PF=m CONFIG_PARIDE_PT=m CONFIG_PARIDE_PG=m # # Parallel IDE protocol modules # CONFIG_PARIDE_ATEN=m CONFIG_PARIDE_BPCK=m # CONFIG_PARIDE_BPCK6 is not set CONFIG_PARIDE_COMM=m CONFIG_PARIDE_DSTR=m CONFIG_PARIDE_FIT2=m CONFIG_PARIDE_FIT3=m CONFIG_PARIDE_EPAT=m CONFIG_PARIDE_EPATC8=y CONFIG_PARIDE_EPIA=m CONFIG_PARIDE_FRIQ=m CONFIG_PARIDE_FRPW=m CONFIG_PARIDE_KBIC=m CONFIG_PARIDE_KTTI=m CONFIG_PARIDE_ON20=m CONFIG_PARIDE_ON26=m CONFIG_BLK_CPQ_DA=m CONFIG_BLK_CPQ_CISS_DA=m CONFIG_CISS_SCSI_TAPE=y CONFIG_BLK_DEV_DAC960=m CONFIG_BLK_DEV_UMEM=m # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=m CONFIG_BLK_DEV_CRYPTOLOOP=m CONFIG_BLK_DEV_NBD=m CONFIG_BLK_DEV_SX8=m CONFIG_BLK_DEV_UB=m CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=16384 CONFIG_BLK_DEV_RAM_BLOCKSIZE=4096 CONFIG_BLK_DEV_INITRD=y CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set CONFIG_ATA_OVER_ETH=m # # Misc devices # # CONFIG_IBM_ASM is not set # CONFIG_SGI_IOC4 is not set # CONFIG_TIFM_CORE is not set # # ATA/ATAPI/MFM/RLL support # CONFIG_IDE=y CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide.txt for help/info on IDE drives # # CONFIG_BLK_DEV_IDE_SATA is not set # CONFIG_BLK_DEV_HD_IDE is not set CONFIG_BLK_DEV_IDEDISK=y CONFIG_IDEDISK_MULTI_MODE=y CONFIG_BLK_DEV_IDECS=m CONFIG_BLK_DEV_IDECD=m # CONFIG_BLK_DEV_IDETAPE is not set CONFIG_BLK_DEV_IDEFLOPPY=y CONFIG_BLK_DEV_IDESCSI=m CONFIG_IDE_TASK_IOCTL=y # # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y # CONFIG_BLK_DEV_CMD640 is not set CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y # CONFIG_BLK_DEV_OFFBOARD is not set CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set # CONFIG_BLK_DEV_RZ1000 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y # CONFIG_BLK_DEV_IDEDMA_FORCED is not set CONFIG_IDEDMA_PCI_AUTO=y # CONFIG_IDEDMA_ONLYDISK is not set CONFIG_BLK_DEV_AEC62XX=y CONFIG_BLK_DEV_ALI15X3=y # CONFIG_WDC_ALI15X3 is not set CONFIG_BLK_DEV_AMD74XX=y CONFIG_BLK_DEV_ATIIXP=y CONFIG_BLK_DEV_CMD64X=y # CONFIG_BLK_DEV_TRIFLEX is not set # CONFIG_BLK_DEV_CY82C693 is not set # CONFIG_BLK_DEV_CS5520 is not set # CONFIG_BLK_DEV_CS5530 is not set # CONFIG_BLK_DEV_CS5535 is not set CONFIG_BLK_DEV_HPT34X=y # CONFIG_HPT34X_AUTODMA is not set CONFIG_BLK_DEV_HPT366=y # CONFIG_BLK_DEV_JMICRON is not set # CONFIG_BLK_DEV_SC1200 is not set CONFIG_BLK_DEV_PIIX=y CONFIG_BLK_DEV_IT821X=y # CONFIG_BLK_DEV_NS87415 is not set CONFIG_BLK_DEV_PDC202XX_OLD=y # CONFIG_PDC202XX_BURST is not set CONFIG_BLK_DEV_PDC202XX_NEW=y CONFIG_BLK_DEV_SVWKS=y CONFIG_BLK_DEV_SIIMAGE=y CONFIG_BLK_DEV_SIS5513=y # CONFIG_BLK_DEV_SLC90E66 is not set # CONFIG_BLK_DEV_TRM290 is not set CONFIG_BLK_DEV_VIA82CXXX=y # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y # CONFIG_IDEDMA_IVB is not set CONFIG_IDEDMA_AUTO=y # CONFIG_BLK_DEV_HD is not set # # SCSI device support # CONFIG_RAID_ATTRS=m CONFIG_SCSI=m CONFIG_SCSI_NETLINK=y CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=m CONFIG_CHR_DEV_ST=m CONFIG_CHR_DEV_OSST=m CONFIG_BLK_DEV_SR=m CONFIG_BLK_DEV_SR_VENDOR=y CONFIG_CHR_DEV_SG=m CONFIG_CHR_DEV_SCH=m # # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y # # SCSI Transports # CONFIG_SCSI_SPI_ATTRS=m CONFIG_SCSI_FC_ATTRS=m CONFIG_SCSI_ISCSI_ATTRS=m CONFIG_SCSI_SAS_ATTRS=m CONFIG_SCSI_SAS_LIBSAS=m # CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set # # SCSI low-level drivers # CONFIG_ISCSI_TCP=m CONFIG_BLK_DEV_3W_XXXX_RAID=m CONFIG_SCSI_3W_9XXX=m CONFIG_SCSI_ACARD=m CONFIG_SCSI_AACRAID=m CONFIG_SCSI_AIC7XXX=m CONFIG_AIC7XXX_CMDS_PER_DEVICE=4 CONFIG_AIC7XXX_RESET_DELAY_MS=15000 # CONFIG_AIC7XXX_DEBUG_ENABLE is not set CONFIG_AIC7XXX_DEBUG_MASK=0 # CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set CONFIG_SCSI_AIC7XXX_OLD=m CONFIG_SCSI_AIC79XX=m CONFIG_AIC79XX_CMDS_PER_DEVICE=4 CONFIG_AIC79XX_RESET_DELAY_MS=15000 # CONFIG_AIC79XX_ENABLE_RD_STRM is not set # CONFIG_AIC79XX_DEBUG_ENABLE is not set CONFIG_AIC79XX_DEBUG_MASK=0 # CONFIG_AIC79XX_REG_PRETTY_PRINT is not set CONFIG_SCSI_AIC94XX=m # CONFIG_AIC94XX_DEBUG is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set CONFIG_MEGARAID_NEWGEN=y CONFIG_MEGARAID_MM=m CONFIG_MEGARAID_MAILBOX=m CONFIG_MEGARAID_LEGACY=m CONFIG_MEGARAID_SAS=m CONFIG_SCSI_HPTIOP=m CONFIG_SCSI_BUSLOGIC=m # CONFIG_SCSI_OMIT_FLASHPOINT is not set # CONFIG_SCSI_DMX3191D is not set # CONFIG_SCSI_EATA is not set # CONFIG_SCSI_FUTURE_DOMAIN is not set CONFIG_SCSI_GDTH=m CONFIG_SCSI_IPS=m CONFIG_SCSI_INITIO=m CONFIG_SCSI_INIA100=m CONFIG_SCSI_PPA=m CONFIG_SCSI_IMM=m # CONFIG_SCSI_IZIP_EPP16 is not set # CONFIG_SCSI_IZIP_SLOW_CTR is not set # CONFIG_SCSI_STEX is not set CONFIG_SCSI_SYM53C8XX_2=m CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1 CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16 CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64 CONFIG_SCSI_SYM53C8XX_MMIO=y # CONFIG_SCSI_IPR is not set CONFIG_SCSI_QLOGIC_1280=m CONFIG_SCSI_QLA_FC=m CONFIG_SCSI_QLA_ISCSI=m CONFIG_SCSI_LPFC=m CONFIG_SCSI_DC395x=m CONFIG_SCSI_DC390T=m # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set # # PCMCIA SCSI adapter support # # CONFIG_PCMCIA_AHA152X is not set # CONFIG_PCMCIA_FDOMAIN is not set # CONFIG_PCMCIA_NINJA_SCSI is not set CONFIG_PCMCIA_QLOGIC=m CONFIG_PCMCIA_SYM53C500=m # # Serial ATA (prod) and Parallel ATA (experimental) drivers # CONFIG_ATA=m CONFIG_SATA_AHCI=m CONFIG_SATA_SVW=m CONFIG_ATA_PIIX=m CONFIG_SATA_MV=m CONFIG_SATA_NV=m CONFIG_PDC_ADMA=m CONFIG_SATA_QSTOR=m CONFIG_SATA_PROMISE=m CONFIG_SATA_SX4=m CONFIG_SATA_SIL=m CONFIG_SATA_SIL24=m CONFIG_SATA_SIS=m CONFIG_SATA_ULI=m CONFIG_SATA_VIA=m CONFIG_SATA_VITESSE=m CONFIG_SATA_INTEL_COMBINED=y CONFIG_PATA_ALI=m CONFIG_PATA_AMD=m CONFIG_PATA_ARTOP=m CONFIG_PATA_ATIIXP=m CONFIG_PATA_CMD64X=m CONFIG_PATA_CS5520=m CONFIG_PATA_CS5530=m # CONFIG_PATA_CS5535 is not set CONFIG_PATA_CYPRESS=m CONFIG_PATA_EFAR=m CONFIG_ATA_GENERIC=m CONFIG_PATA_HPT366=m CONFIG_PATA_HPT37X=m CONFIG_PATA_HPT3X2N=m CONFIG_PATA_HPT3X3=m CONFIG_PATA_IT821X=m CONFIG_PATA_JMICRON=m CONFIG_PATA_TRIFLEX=m CONFIG_PATA_MPIIX=m CONFIG_PATA_OLDPIIX=m CONFIG_PATA_NETCELL=m CONFIG_PATA_NS87410=m CONFIG_PATA_OPTI=m CONFIG_PATA_OPTIDMA=m CONFIG_PATA_PCMCIA=m CONFIG_PATA_PDC_OLD=m CONFIG_PATA_RADISYS=m CONFIG_PATA_RZ1000=m CONFIG_PATA_SC1200=m CONFIG_PATA_SERVERWORKS=m CONFIG_PATA_PDC2027X=m CONFIG_PATA_SIL680=m CONFIG_PATA_SIS=m CONFIG_PATA_VIA=m CONFIG_PATA_WINBOND=m # # Multi-device support (RAID and LVM) # CONFIG_MD=y CONFIG_BLK_DEV_MD=y CONFIG_MD_LINEAR=m CONFIG_MD_RAID0=m CONFIG_MD_RAID1=m CONFIG_MD_RAID10=m CONFIG_MD_RAID456=m CONFIG_MD_RAID5_RESHAPE=y CONFIG_MD_MULTIPATH=m CONFIG_MD_FAULTY=m CONFIG_BLK_DEV_DM=m # CONFIG_DM_DEBUG is not set CONFIG_DM_CRYPT=m CONFIG_DM_SNAPSHOT=m CONFIG_DM_MIRROR=m CONFIG_DM_ZERO=m CONFIG_DM_MULTIPATH=m CONFIG_DM_MULTIPATH_EMC=m # # Fusion MPT device support # CONFIG_FUSION=y CONFIG_FUSION_SPI=m CONFIG_FUSION_FC=m CONFIG_FUSION_SAS=m CONFIG_FUSION_MAX_SGE=40 CONFIG_FUSION_CTL=m CONFIG_FUSION_LAN=m # # IEEE 1394 (FireWire) support # CONFIG_IEEE1394=m # # Subsystem Options # # CONFIG_IEEE1394_VERBOSEDEBUG is not set CONFIG_IEEE1394_OUI_DB=y CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y CONFIG_IEEE1394_CONFIG_ROM_IP1394=y # CONFIG_IEEE1394_EXPORT_FULL_API is not set # # Device Drivers # CONFIG_IEEE1394_PCILYNX=m CONFIG_IEEE1394_OHCI1394=m # # Protocol Drivers # CONFIG_IEEE1394_VIDEO1394=m CONFIG_IEEE1394_SBP2=m # CONFIG_IEEE1394_SBP2_PHYS_DMA is not set CONFIG_IEEE1394_ETH1394=m CONFIG_IEEE1394_DV1394=m CONFIG_IEEE1394_RAWIO=m # # I2O device support # CONFIG_I2O=m # CONFIG_I2O_LCT_NOTIFY_ON_CHANGES is not set CONFIG_I2O_EXT_ADAPTEC=y CONFIG_I2O_CONFIG=m CONFIG_I2O_CONFIG_OLD_IOCTL=y CONFIG_I2O_BUS=m CONFIG_I2O_BLOCK=m CONFIG_I2O_SCSI=m CONFIG_I2O_PROC=m # # Network device support # CONFIG_NETDEVICES=y CONFIG_IFB=m CONFIG_DUMMY=m CONFIG_BONDING=m CONFIG_EQUALIZER=m CONFIG_TUN=m # # ARCnet devices # # CONFIG_ARCNET is not set # # PHY device support # CONFIG_PHYLIB=m # # MII PHY device drivers # CONFIG_MARVELL_PHY=m CONFIG_DAVICOM_PHY=m CONFIG_QSEMI_PHY=m CONFIG_LXT_PHY=m CONFIG_CICADA_PHY=m CONFIG_VITESSE_PHY=m CONFIG_SMSC_PHY=m CONFIG_FIXED_PHY=m CONFIG_FIXED_MII_10_FDX=y CONFIG_FIXED_MII_100_FDX=y # # Ethernet (10 or 100Mbit) # CONFIG_NET_ETHERNET=y CONFIG_MII=m CONFIG_HAPPYMEAL=m CONFIG_SUNGEM=m CONFIG_CASSINI=m CONFIG_NET_VENDOR_3COM=y CONFIG_VORTEX=m CONFIG_TYPHOON=m # # Tulip family network device support # CONFIG_NET_TULIP=y CONFIG_DE2104X=m CONFIG_TULIP=m # CONFIG_TULIP_MWI is not set CONFIG_TULIP_MMIO=y # CONFIG_TULIP_NAPI is not set CONFIG_DE4X5=m CONFIG_WINBOND_840=m CONFIG_DM9102=m CONFIG_ULI526X=m CONFIG_PCMCIA_XIRCOM=m # CONFIG_HP100 is not set CONFIG_NET_PCI=y CONFIG_PCNET32=m # CONFIG_PCNET32_NAPI is not set CONFIG_AMD8111_ETH=m CONFIG_AMD8111E_NAPI=y CONFIG_ADAPTEC_STARFIRE=m CONFIG_ADAPTEC_STARFIRE_NAPI=y CONFIG_B44=m CONFIG_FORCEDETH=m # CONFIG_FORCEDETH_NAPI is not set # CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set CONFIG_E100=m CONFIG_FEALNX=m CONFIG_NATSEMI=m CONFIG_NE2K_PCI=m CONFIG_8139CP=m CONFIG_8139TOO=m # CONFIG_8139TOO_PIO is not set # CONFIG_8139TOO_TUNE_TWISTER is not set CONFIG_8139TOO_8129=y # CONFIG_8139_OLD_RX_RESET is not set CONFIG_SIS900=m CONFIG_EPIC100=m CONFIG_SUNDANCE=m # CONFIG_SUNDANCE_MMIO is not set # CONFIG_TLAN is not set CONFIG_VIA_RHINE=m CONFIG_VIA_RHINE_MMIO=y CONFIG_VIA_RHINE_NAPI=y CONFIG_NET_POCKET=y CONFIG_ATP=m CONFIG_DE600=m CONFIG_DE620=m # # Ethernet (1000 Mbit) # CONFIG_ACENIC=m # CONFIG_ACENIC_OMIT_TIGON_I is not set CONFIG_DL2K=m CONFIG_E1000=m CONFIG_E1000_NAPI=y # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set CONFIG_NS83820=m CONFIG_HAMACHI=m CONFIG_YELLOWFIN=m CONFIG_R8169=m CONFIG_R8169_NAPI=y CONFIG_R8169_VLAN=y CONFIG_SIS190=m CONFIG_SKGE=m CONFIG_SKY2=m # CONFIG_SK98LIN is not set CONFIG_VIA_VELOCITY=m CONFIG_TIGON3=m CONFIG_BNX2=m # CONFIG_QLA3XXX is not set # # Ethernet (10000 Mbit) # CONFIG_CHELSIO_T1=m CONFIG_IXGB=m CONFIG_IXGB_NAPI=y CONFIG_S2IO=m CONFIG_S2IO_NAPI=y CONFIG_MYRI10GE=m # # Token Ring devices # CONFIG_TR=y CONFIG_IBMOL=m # CONFIG_IBMLS is not set CONFIG_3C359=m # CONFIG_TMS380TR is not set # # Wireless LAN (non-hamradio) # CONFIG_NET_RADIO=y CONFIG_NET_WIRELESS_RTNETLINK=y # # Obsolete Wireless cards support (pre-802.11) # # CONFIG_STRIP is not set CONFIG_PCMCIA_WAVELAN=m CONFIG_PCMCIA_NETWAVE=m # # Wireless 802.11 Frequency Hopping cards support # # CONFIG_PCMCIA_RAYCS is not set # # Wireless 802.11b ISA/PCI cards support # CONFIG_IPW2100=m CONFIG_IPW2100_MONITOR=y # CONFIG_IPW2100_DEBUG is not set CONFIG_IPW2200=m CONFIG_IPW2200_MONITOR=y CONFIG_IPW2200_RADIOTAP=y CONFIG_IPW2200_PROMISCUOUS=y CONFIG_IPW2200_QOS=y # CONFIG_IPW2200_DEBUG is not set CONFIG_AIRO=m CONFIG_HERMES=m CONFIG_PLX_HERMES=m CONFIG_TMD_HERMES=m CONFIG_NORTEL_HERMES=m CONFIG_PCI_HERMES=m CONFIG_ATMEL=m CONFIG_PCI_ATMEL=m # # Wireless 802.11b Pcmcia/Cardbus cards support # CONFIG_PCMCIA_HERMES=m CONFIG_PCMCIA_SPECTRUM=m CONFIG_AIRO_CS=m CONFIG_PCMCIA_ATMEL=m CONFIG_PCMCIA_WL3501=m # # Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support # CONFIG_PRISM54=m CONFIG_USB_ZD1201=m CONFIG_HOSTAP=m CONFIG_HOSTAP_FIRMWARE=y CONFIG_HOSTAP_FIRMWARE_NVRAM=y CONFIG_HOSTAP_PLX=m CONFIG_HOSTAP_PCI=m CONFIG_HOSTAP_CS=m CONFIG_BCM43XX=m CONFIG_BCM43XX_DEBUG=y CONFIG_BCM43XX_DMA=y CONFIG_BCM43XX_PIO=y CONFIG_BCM43XX_DMA_AND_PIO_MODE=y # CONFIG_BCM43XX_DMA_MODE is not set # CONFIG_BCM43XX_PIO_MODE is not set CONFIG_ZD1211RW=m # CONFIG_ZD1211RW_DEBUG is not set CONFIG_NET_WIRELESS=y # # PCMCIA network device support # CONFIG_NET_PCMCIA=y CONFIG_PCMCIA_3C589=m CONFIG_PCMCIA_3C574=m CONFIG_PCMCIA_FMVJ18X=m CONFIG_PCMCIA_PCNET=m CONFIG_PCMCIA_NMCLAN=m CONFIG_PCMCIA_SMC91C92=m CONFIG_PCMCIA_XIRC2PS=m CONFIG_PCMCIA_AXNET=m # CONFIG_PCMCIA_IBMTR is not set # # Wan interfaces # # CONFIG_WAN is not set # # ATM drivers # # CONFIG_ATM_DUMMY is not set CONFIG_ATM_TCP=m CONFIG_ATM_LANAI=m CONFIG_ATM_ENI=m # CONFIG_ATM_ENI_DEBUG is not set # CONFIG_ATM_ENI_TUNE_BURST is not set CONFIG_ATM_FIRESTREAM=m # CONFIG_ATM_ZATM is not set # CONFIG_ATM_NICSTAR is not set CONFIG_ATM_IDT77252=m # CONFIG_ATM_IDT77252_DEBUG is not set # CONFIG_ATM_IDT77252_RCV_ALL is not set CONFIG_ATM_IDT77252_USE_SUNI=y CONFIG_ATM_AMBASSADOR=m # CONFIG_ATM_AMBASSADOR_DEBUG is not set CONFIG_ATM_HORIZON=m # CONFIG_ATM_HORIZON_DEBUG is not set # CONFIG_ATM_IA is not set CONFIG_ATM_FORE200E_MAYBE=m # CONFIG_ATM_FORE200E_PCA is not set CONFIG_ATM_HE=m # CONFIG_ATM_HE_USE_SUNI is not set CONFIG_FDDI=y # CONFIG_DEFXX is not set CONFIG_SKFP=m # CONFIG_HIPPI is not set CONFIG_PLIP=m CONFIG_PPP=m CONFIG_PPP_MULTILINK=y CONFIG_PPP_FILTER=y CONFIG_PPP_ASYNC=m CONFIG_PPP_SYNC_TTY=m CONFIG_PPP_DEFLATE=m # CONFIG_PPP_BSDCOMP is not set CONFIG_PPP_MPPE=m CONFIG_PPPOE=m CONFIG_PPPOATM=m CONFIG_SLIP=m CONFIG_SLIP_COMPRESSED=y CONFIG_SLHC=m CONFIG_SLIP_SMART=y # CONFIG_SLIP_MODE_SLIP6 is not set CONFIG_NET_FC=y # CONFIG_SHAPER is not set CONFIG_NETCONSOLE=m CONFIG_NETPOLL=y # CONFIG_NETPOLL_RX is not set CONFIG_NETPOLL_TRAP=y CONFIG_NET_POLL_CONTROLLER=y # # ISDN subsystem # # CONFIG_ISDN is not set # # Telephony Support # # CONFIG_PHONE is not set # # Input device support # CONFIG_INPUT=y CONFIG_INPUT_FF_MEMLESS=y # # Userland interfaces # CONFIG_INPUT_MOUSEDEV=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 CONFIG_INPUT_JOYDEV=m # CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y CONFIG_MOUSE_SERIAL=m CONFIG_MOUSE_VSXXXAA=m CONFIG_INPUT_JOYSTICK=y CONFIG_JOYSTICK_ANALOG=m CONFIG_JOYSTICK_A3D=m CONFIG_JOYSTICK_ADI=m CONFIG_JOYSTICK_COBRA=m CONFIG_JOYSTICK_GF2K=m CONFIG_JOYSTICK_GRIP=m CONFIG_JOYSTICK_GRIP_MP=m CONFIG_JOYSTICK_GUILLEMOT=m CONFIG_JOYSTICK_INTERACT=m CONFIG_JOYSTICK_SIDEWINDER=m CONFIG_JOYSTICK_TMDC=m CONFIG_JOYSTICK_IFORCE=m CONFIG_JOYSTICK_IFORCE_USB=y CONFIG_JOYSTICK_IFORCE_232=y CONFIG_JOYSTICK_WARRIOR=m CONFIG_JOYSTICK_MAGELLAN=m CONFIG_JOYSTICK_SPACEORB=m CONFIG_JOYSTICK_SPACEBALL=m CONFIG_JOYSTICK_STINGER=m CONFIG_JOYSTICK_TWIDJOY=m CONFIG_JOYSTICK_DB9=m CONFIG_JOYSTICK_GAMECON=m CONFIG_JOYSTICK_TURBOGRAFX=m CONFIG_JOYSTICK_JOYDUMP=m CONFIG_INPUT_TOUCHSCREEN=y CONFIG_TOUCHSCREEN_GUNZE=m CONFIG_TOUCHSCREEN_ELO=m CONFIG_TOUCHSCREEN_MTOUCH=m CONFIG_TOUCHSCREEN_MK712=m # CONFIG_TOUCHSCREEN_PENMOUNT is not set # CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set # CONFIG_TOUCHSCREEN_TOUCHWIN is not set CONFIG_INPUT_MISC=y CONFIG_INPUT_PCSPKR=m # CONFIG_INPUT_WISTRON_BTNS is not set CONFIG_INPUT_UINPUT=m # # Hardware I/O ports # CONFIG_SERIO=y CONFIG_SERIO_I8042=y CONFIG_SERIO_SERPORT=y # CONFIG_SERIO_CT82C710 is not set # CONFIG_SERIO_PARKBD is not set # CONFIG_SERIO_PCIPS2 is not set CONFIG_SERIO_LIBPS2=y CONFIG_SERIO_RAW=m CONFIG_GAMEPORT=m CONFIG_GAMEPORT_NS558=m CONFIG_GAMEPORT_L4=m CONFIG_GAMEPORT_EMU10K1=m CONFIG_GAMEPORT_FM801=m # # Character devices # CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y CONFIG_SERIAL_NONSTANDARD=y # CONFIG_COMPUTONE is not set # CONFIG_ROCKETPORT is not set CONFIG_CYCLADES=m # CONFIG_CYZ_INTR is not set # CONFIG_DIGIEPCA is not set # CONFIG_MOXA_INTELLIO is not set # CONFIG_MOXA_SMARTIO is not set # CONFIG_ISI is not set CONFIG_SYNCLINK=m CONFIG_SYNCLINKMP=m CONFIG_SYNCLINK_GT=m CONFIG_N_HDLC=m # CONFIG_SPECIALIX is not set # CONFIG_SX is not set # CONFIG_RIO is not set # CONFIG_STALDRV is not set # # Serial drivers # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_CS=m CONFIG_SERIAL_8250_NR_UARTS=32 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y CONFIG_SERIAL_8250_DETECT_IRQ=y CONFIG_SERIAL_8250_RSA=y # # Non-8250 serial port support # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_SERIAL_JSM=m CONFIG_UNIX98_PTYS=y # CONFIG_LEGACY_PTYS is not set CONFIG_PRINTER=m CONFIG_LP_CONSOLE=y CONFIG_PPDEV=m CONFIG_TIPAR=m # # IPMI # CONFIG_IPMI_HANDLER=m # CONFIG_IPMI_PANIC_EVENT is not set CONFIG_IPMI_DEVICE_INTERFACE=m CONFIG_IPMI_SI=m CONFIG_IPMI_WATCHDOG=m CONFIG_IPMI_POWEROFF=m # # Watchdog Cards # CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set # # Watchdog Device Drivers # CONFIG_SOFT_WATCHDOG=m # CONFIG_ACQUIRE_WDT is not set # CONFIG_ADVANTECH_WDT is not set CONFIG_ALIM1535_WDT=m CONFIG_ALIM7101_WDT=m # CONFIG_SC520_WDT is not set # CONFIG_EUROTECH_WDT is not set # CONFIG_IB700_WDT is not set CONFIG_IBMASR=m # CONFIG_WAFER_WDT is not set CONFIG_I6300ESB_WDT=m CONFIG_I8XX_TCO=m # CONFIG_ITCO_WDT is not set # CONFIG_SC1200_WDT is not set # CONFIG_60XX_WDT is not set # CONFIG_SBC8360_WDT is not set # CONFIG_CPU5_WDT is not set # CONFIG_SMSC37B787_WDT is not set CONFIG_W83627HF_WDT=m # CONFIG_W83697HF_WDT is not set CONFIG_W83877F_WDT=m CONFIG_W83977F_WDT=m CONFIG_MACHZ_WDT=m # CONFIG_SBC_EPX_C3_WATCHDOG is not set # # PCI-based Watchdog Cards # CONFIG_PCIPCWATCHDOG=m CONFIG_WDTPCI=m CONFIG_WDT_501_PCI=y # # USB-based Watchdog Cards # CONFIG_USBPCWATCHDOG=m CONFIG_HW_RANDOM=y CONFIG_HW_RANDOM_INTEL=m CONFIG_HW_RANDOM_AMD=m # CONFIG_HW_RANDOM_GEODE is not set CONFIG_HW_RANDOM_VIA=y CONFIG_NVRAM=y CONFIG_RTC=y CONFIG_DTLK=m CONFIG_R3964=m # CONFIG_APPLICOM is not set # CONFIG_SONYPI is not set # # Ftape, the floppy tape device driver # CONFIG_AGP=y # CONFIG_AGP_ALI is not set # CONFIG_AGP_ATI is not set # CONFIG_AGP_AMD is not set CONFIG_AGP_AMD64=y CONFIG_AGP_INTEL=y # CONFIG_AGP_NVIDIA is not set CONFIG_AGP_SIS=y # CONFIG_AGP_SWORKS is not set CONFIG_AGP_VIA=y # CONFIG_AGP_EFFICEON is not set CONFIG_DRM=m CONFIG_DRM_TDFX=m CONFIG_DRM_R128=m CONFIG_DRM_RADEON=m CONFIG_DRM_I810=m CONFIG_DRM_I830=m CONFIG_DRM_I915=m CONFIG_DRM_MGA=m CONFIG_DRM_SIS=m CONFIG_DRM_VIA=m CONFIG_DRM_SAVAGE=m # # PCMCIA character devices # # CONFIG_SYNCLINK_CS is not set CONFIG_CARDMAN_4000=m CONFIG_CARDMAN_4040=m CONFIG_MWAVE=m CONFIG_PC8736x_GPIO=m CONFIG_NSC_GPIO=m # CONFIG_CS5535_GPIO is not set # CONFIG_RAW_DRIVER is not set CONFIG_HANGCHECK_TIMER=m # # TPM devices # CONFIG_TCG_TPM=m CONFIG_TCG_ATMEL=m # CONFIG_TELCLOCK is not set # # I2C support # CONFIG_I2C=m CONFIG_I2C_CHARDEV=m # # I2C Algorithms # CONFIG_I2C_ALGOBIT=m CONFIG_I2C_ALGOPCF=m CONFIG_I2C_ALGOPCA=m # # I2C Hardware Bus support # # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set CONFIG_I2C_AMD756=m CONFIG_I2C_AMD756_S4882=m CONFIG_I2C_AMD8111=m CONFIG_I2C_I801=m # CONFIG_I2C_I810 is not set # CONFIG_I2C_PIIX4 is not set CONFIG_I2C_ISA=m CONFIG_I2C_NFORCE2=m # CONFIG_I2C_OCORES is not set CONFIG_I2C_PARPORT=m CONFIG_I2C_PARPORT_LIGHT=m CONFIG_I2C_PROSAVAGE=m CONFIG_I2C_SAVAGE4=m # CONFIG_SCx200_ACB is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set CONFIG_I2C_SIS96X=m CONFIG_I2C_STUB=m CONFIG_I2C_VIA=m CONFIG_I2C_VIAPRO=m CONFIG_I2C_VOODOO3=m CONFIG_I2C_PCA_ISA=m # # Miscellaneous I2C Chip support # CONFIG_SENSORS_DS1337=m CONFIG_SENSORS_DS1374=m CONFIG_SENSORS_EEPROM=m CONFIG_SENSORS_PCF8574=m CONFIG_SENSORS_PCA9539=m CONFIG_SENSORS_PCF8591=m CONFIG_SENSORS_MAX6875=m # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # # SPI support # # CONFIG_SPI is not set # CONFIG_SPI_MASTER is not set # # Dallas's 1-wire bus # # CONFIG_W1 is not set # # Hardware Monitoring support # CONFIG_HWMON=m CONFIG_HWMON_VID=m CONFIG_SENSORS_ABITUGURU=m CONFIG_SENSORS_ADM1021=m CONFIG_SENSORS_ADM1025=m CONFIG_SENSORS_ADM1026=m CONFIG_SENSORS_ADM1031=m CONFIG_SENSORS_ADM9240=m # CONFIG_SENSORS_K8TEMP is not set CONFIG_SENSORS_ASB100=m CONFIG_SENSORS_ATXP1=m CONFIG_SENSORS_DS1621=m CONFIG_SENSORS_F71805F=m CONFIG_SENSORS_FSCHER=m CONFIG_SENSORS_FSCPOS=m CONFIG_SENSORS_GL518SM=m CONFIG_SENSORS_GL520SM=m CONFIG_SENSORS_IT87=m CONFIG_SENSORS_LM63=m CONFIG_SENSORS_LM75=m CONFIG_SENSORS_LM77=m CONFIG_SENSORS_LM78=m CONFIG_SENSORS_LM80=m CONFIG_SENSORS_LM83=m CONFIG_SENSORS_LM85=m CONFIG_SENSORS_LM87=m CONFIG_SENSORS_LM90=m CONFIG_SENSORS_LM92=m CONFIG_SENSORS_MAX1619=m CONFIG_SENSORS_PC87360=m CONFIG_SENSORS_SIS5595=m CONFIG_SENSORS_SMSC47M1=m CONFIG_SENSORS_SMSC47M192=m CONFIG_SENSORS_SMSC47B397=m CONFIG_SENSORS_VIA686A=m # CONFIG_SENSORS_VT1211 is not set CONFIG_SENSORS_VT8231=m CONFIG_SENSORS_W83781D=m CONFIG_SENSORS_W83791D=m CONFIG_SENSORS_W83792D=m CONFIG_SENSORS_W83L785TS=m CONFIG_SENSORS_W83627HF=m CONFIG_SENSORS_W83627EHF=m CONFIG_SENSORS_HDAPS=m # CONFIG_HWMON_DEBUG_CHIP is not set # # Multimedia devices # CONFIG_VIDEO_DEV=m CONFIG_VIDEO_V4L1=y CONFIG_VIDEO_V4L1_COMPAT=y CONFIG_VIDEO_V4L2=y # # Video Capture Adapters # # # Video Capture Adapters # # CONFIG_VIDEO_ADV_DEBUG is not set CONFIG_VIDEO_HELPER_CHIPS_AUTO=y CONFIG_VIDEO_TVAUDIO=m CONFIG_VIDEO_TDA7432=m CONFIG_VIDEO_TDA9840=m CONFIG_VIDEO_TDA9875=m CONFIG_VIDEO_TEA6415C=m CONFIG_VIDEO_TEA6420=m CONFIG_VIDEO_MSP3400=m CONFIG_VIDEO_WM8775=m CONFIG_VIDEO_BT819=m CONFIG_VIDEO_BT856=m CONFIG_VIDEO_KS0127=m CONFIG_VIDEO_SAA7110=m CONFIG_VIDEO_SAA7111=m CONFIG_VIDEO_SAA7114=m CONFIG_VIDEO_SAA711X=m CONFIG_VIDEO_TVP5150=m CONFIG_VIDEO_VPX3220=m CONFIG_VIDEO_CX25840=m CONFIG_VIDEO_CX2341X=m CONFIG_VIDEO_SAA7185=m CONFIG_VIDEO_ADV7170=m CONFIG_VIDEO_ADV7175=m # CONFIG_VIDEO_VIVI is not set CONFIG_VIDEO_BT848=m CONFIG_VIDEO_SAA6588=m CONFIG_VIDEO_BWQCAM=m CONFIG_VIDEO_CQCAM=m CONFIG_VIDEO_W9966=m CONFIG_VIDEO_CPIA=m CONFIG_VIDEO_CPIA_PP=m CONFIG_VIDEO_CPIA_USB=m CONFIG_VIDEO_CPIA2=m CONFIG_VIDEO_SAA5246A=m CONFIG_VIDEO_SAA5249=m CONFIG_TUNER_3036=m CONFIG_VIDEO_STRADIS=m CONFIG_VIDEO_ZORAN_ZR36060=m CONFIG_VIDEO_ZORAN=m CONFIG_VIDEO_ZORAN_BUZ=m CONFIG_VIDEO_ZORAN_DC10=m CONFIG_VIDEO_ZORAN_DC30=m CONFIG_VIDEO_ZORAN_LML33=m CONFIG_VIDEO_ZORAN_LML33R10=m CONFIG_VIDEO_ZORAN_AVS6EYES=m CONFIG_VIDEO_SAA7134=m CONFIG_VIDEO_SAA7134_ALSA=m CONFIG_VIDEO_MXB=m CONFIG_VIDEO_DPC=m CONFIG_VIDEO_HEXIUM_ORION=m CONFIG_VIDEO_HEXIUM_GEMINI=m CONFIG_VIDEO_CX88=m CONFIG_VIDEO_CX88_ALSA=m CONFIG_VIDEO_CX88_BLACKBIRD=m # # V4L USB devices # CONFIG_VIDEO_PVRUSB2=m # CONFIG_VIDEO_PVRUSB2_29XXX is not set CONFIG_VIDEO_PVRUSB2_24XXX=y CONFIG_VIDEO_PVRUSB2_SYSFS=y # CONFIG_VIDEO_PVRUSB2_DEBUGIFC is not set CONFIG_VIDEO_EM28XX=m CONFIG_VIDEO_USBVIDEO=m CONFIG_USB_VICAM=m CONFIG_USB_IBMCAM=m CONFIG_USB_KONICAWC=m CONFIG_USB_QUICKCAM_MESSENGER=m CONFIG_USB_ET61X251=m CONFIG_VIDEO_OVCAMCHIP=m CONFIG_USB_W9968CF=m CONFIG_USB_OV511=m CONFIG_USB_SE401=m CONFIG_USB_SN9C102=m CONFIG_USB_STV680=m CONFIG_USB_ZC0301=m CONFIG_USB_PWC=m # CONFIG_USB_PWC_DEBUG is not set # # Radio Adapters # CONFIG_RADIO_GEMTEK_PCI=m CONFIG_RADIO_MAXIRADIO=m CONFIG_RADIO_MAESTRO=m CONFIG_USB_DSBR=m # # Digital Video Broadcasting Devices # # CONFIG_DVB is not set CONFIG_VIDEO_SAA7146=m CONFIG_VIDEO_SAA7146_VV=m CONFIG_VIDEO_VIDEOBUF=m CONFIG_VIDEO_TUNER=m CONFIG_VIDEO_BUF=m CONFIG_VIDEO_BTCX=m CONFIG_VIDEO_IR=m CONFIG_VIDEO_TVEEPROM=m # CONFIG_USB_DABUSB is not set # # Graphics support # # CONFIG_FIRMWARE_EDID is not set CONFIG_FB=y CONFIG_FB_DDC=m CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set CONFIG_FB_MODE_HELPERS=y CONFIG_FB_TILEBLITTING=y CONFIG_FB_CIRRUS=m # CONFIG_FB_PM2 is not set # CONFIG_FB_CYBER2000 is not set # CONFIG_FB_ARC is not set # CONFIG_FB_ASILIANT is not set # CONFIG_FB_IMSTT is not set CONFIG_FB_VGA16=m CONFIG_FB_VESA=y # CONFIG_FB_HGA is not set # CONFIG_FB_S1D13XXX is not set CONFIG_FB_NVIDIA=m CONFIG_FB_NVIDIA_I2C=y CONFIG_FB_RIVA=m # CONFIG_FB_RIVA_I2C is not set # CONFIG_FB_RIVA_DEBUG is not set # CONFIG_FB_I810 is not set CONFIG_FB_INTEL=m # CONFIG_FB_INTEL_DEBUG is not set CONFIG_FB_INTEL_I2C=y CONFIG_FB_MATROX=m CONFIG_FB_MATROX_MILLENIUM=y CONFIG_FB_MATROX_MYSTIQUE=y CONFIG_FB_MATROX_G=y CONFIG_FB_MATROX_I2C=m CONFIG_FB_MATROX_MAVEN=m CONFIG_FB_MATROX_MULTIHEAD=y CONFIG_FB_RADEON=m CONFIG_FB_RADEON_I2C=y # CONFIG_FB_RADEON_DEBUG is not set CONFIG_FB_ATY128=m CONFIG_FB_ATY=m CONFIG_FB_ATY_CT=y CONFIG_FB_ATY_GENERIC_LCD=y CONFIG_FB_ATY_GX=y CONFIG_FB_SAVAGE=m CONFIG_FB_SAVAGE_I2C=y CONFIG_FB_SAVAGE_ACCEL=y # CONFIG_FB_SIS is not set CONFIG_FB_NEOMAGIC=m CONFIG_FB_KYRO=m CONFIG_FB_3DFX=m CONFIG_FB_3DFX_ACCEL=y CONFIG_FB_VOODOO1=m # CONFIG_FB_CYBLA is not set CONFIG_FB_TRIDENT=m CONFIG_FB_TRIDENT_ACCEL=y # CONFIG_FB_GEODE is not set # CONFIG_FB_VIRTUAL is not set # # Console display driver support # CONFIG_VGA_CONSOLE=y CONFIG_VGACON_SOFT_SCROLLBACK=y CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64 CONFIG_VIDEO_SELECT=y CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y # # Logo configuration # CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set CONFIG_LOGO_LINUX_CLUT224=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_BACKLIGHT_CLASS_DEVICE=m CONFIG_BACKLIGHT_DEVICE=y CONFIG_LCD_CLASS_DEVICE=m CONFIG_LCD_DEVICE=y # # Sound # CONFIG_SOUND=m # # Advanced Linux Sound Architecture # CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m CONFIG_SND_HWDEP=m CONFIG_SND_RAWMIDI=m CONFIG_SND_SEQUENCER=m CONFIG_SND_SEQ_DUMMY=m CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=m CONFIG_SND_PCM_OSS=m CONFIG_SND_PCM_OSS_PLUGINS=y CONFIG_SND_SEQUENCER_OSS=y CONFIG_SND_RTCTIMER=m CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y CONFIG_SND_DYNAMIC_MINORS=y # CONFIG_SND_SUPPORT_OLD_API is not set CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set # # Generic devices # CONFIG_SND_MPU401_UART=m CONFIG_SND_OPL3_LIB=m CONFIG_SND_VX_LIB=m CONFIG_SND_AC97_CODEC=m CONFIG_SND_AC97_BUS=m CONFIG_SND_DUMMY=m CONFIG_SND_VIRMIDI=m CONFIG_SND_MTPAV=m # CONFIG_SND_MTS64 is not set # CONFIG_SND_SERIAL_U16550 is not set CONFIG_SND_MPU401=m # # PCI devices # CONFIG_SND_AD1889=m CONFIG_SND_ALS300=m CONFIG_SND_ALS4000=m CONFIG_SND_ALI5451=m CONFIG_SND_ATIIXP=m CONFIG_SND_ATIIXP_MODEM=m CONFIG_SND_AU8810=m CONFIG_SND_AU8820=m CONFIG_SND_AU8830=m CONFIG_SND_AZT3328=m CONFIG_SND_BT87X=m # CONFIG_SND_BT87X_OVERCLOCK is not set CONFIG_SND_CA0106=m CONFIG_SND_CMIPCI=m CONFIG_SND_CS4281=m CONFIG_SND_CS46XX=m CONFIG_SND_CS46XX_NEW_DSP=y # CONFIG_SND_CS5535AUDIO is not set CONFIG_SND_DARLA20=m CONFIG_SND_GINA20=m CONFIG_SND_LAYLA20=m CONFIG_SND_DARLA24=m CONFIG_SND_GINA24=m CONFIG_SND_LAYLA24=m CONFIG_SND_MONA=m CONFIG_SND_MIA=m CONFIG_SND_ECHO3G=m CONFIG_SND_INDIGO=m CONFIG_SND_INDIGOIO=m CONFIG_SND_INDIGODJ=m CONFIG_SND_EMU10K1=m CONFIG_SND_EMU10K1X=m CONFIG_SND_ENS1370=m CONFIG_SND_ENS1371=m CONFIG_SND_ES1938=m CONFIG_SND_ES1968=m CONFIG_SND_FM801=m CONFIG_SND_FM801_TEA575X_BOOL=y CONFIG_SND_FM801_TEA575X=m CONFIG_SND_HDA_INTEL=m CONFIG_SND_HDSP=m CONFIG_SND_HDSPM=m CONFIG_SND_ICE1712=m CONFIG_SND_ICE1724=m CONFIG_SND_INTEL8X0=m CONFIG_SND_INTEL8X0M=m CONFIG_SND_KORG1212=m CONFIG_SND_MAESTRO3=m CONFIG_SND_MIXART=m CONFIG_SND_NM256=m CONFIG_SND_PCXHR=m CONFIG_SND_RIPTIDE=m CONFIG_SND_RME32=m CONFIG_SND_RME96=m CONFIG_SND_RME9652=m CONFIG_SND_SONICVIBES=m CONFIG_SND_TRIDENT=m CONFIG_SND_VIA82XX=m CONFIG_SND_VIA82XX_MODEM=m CONFIG_SND_VX222=m CONFIG_SND_YMFPCI=m # CONFIG_SND_AC97_POWER_SAVE is not set # # USB devices # CONFIG_SND_USB_AUDIO=m CONFIG_SND_USB_USX2Y=m # # PCMCIA devices # # CONFIG_SND_VXPOCKET is not set # CONFIG_SND_PDAUDIOCF is not set # # Open Sound System # # CONFIG_SOUND_PRIME is not set # # USB support # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set # # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y # CONFIG_USB_BANDWIDTH is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_OTG is not set # # USB Host Controller Drivers # CONFIG_USB_EHCI_HCD=m CONFIG_USB_EHCI_SPLIT_ISO=y CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_EHCI_TT_NEWSCHED=y CONFIG_USB_ISP116X_HCD=m CONFIG_USB_OHCI_HCD=m # CONFIG_USB_OHCI_BIG_ENDIAN is not set CONFIG_USB_OHCI_LITTLE_ENDIAN=y CONFIG_USB_UHCI_HCD=m CONFIG_USB_SL811_HCD=m CONFIG_USB_SL811_CS=m # # USB Device Class drivers # CONFIG_USB_ACM=m CONFIG_USB_PRINTER=m # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' # # # may also be needed; see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_DEBUG is not set CONFIG_USB_STORAGE_DATAFAB=y CONFIG_USB_STORAGE_FREECOM=y CONFIG_USB_STORAGE_ISD200=y CONFIG_USB_STORAGE_DPCM=y CONFIG_USB_STORAGE_USBAT=y CONFIG_USB_STORAGE_SDDR09=y CONFIG_USB_STORAGE_SDDR55=y CONFIG_USB_STORAGE_JUMPSHOT=y CONFIG_USB_STORAGE_ALAUDA=y # CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set CONFIG_USB_LIBUSUAL=y # # USB Input Devices # CONFIG_USB_HID=y CONFIG_USB_HIDINPUT=y # CONFIG_USB_HIDINPUT_POWERBOOK is not set CONFIG_HID_FF=y CONFIG_HID_PID=y CONFIG_LOGITECH_FF=y CONFIG_THRUSTMASTER_FF=y # CONFIG_ZEROPLUS_FF is not set CONFIG_USB_HIDDEV=y CONFIG_USB_AIPTEK=m CONFIG_USB_WACOM=m CONFIG_USB_ACECAD=m CONFIG_USB_KBTAB=m CONFIG_USB_POWERMATE=m CONFIG_USB_TOUCHSCREEN=m CONFIG_USB_TOUCHSCREEN_EGALAX=y CONFIG_USB_TOUCHSCREEN_PANJIT=y CONFIG_USB_TOUCHSCREEN_3M=y CONFIG_USB_TOUCHSCREEN_ITM=y CONFIG_USB_TOUCHSCREEN_ETURBO=y CONFIG_USB_TOUCHSCREEN_GUNZE=y # CONFIG_USB_YEALINK is not set CONFIG_USB_XPAD=m CONFIG_USB_ATI_REMOTE=m CONFIG_USB_ATI_REMOTE2=m CONFIG_USB_KEYSPAN_REMOTE=m CONFIG_USB_APPLETOUCH=m # # USB Imaging devices # CONFIG_USB_MDC800=m CONFIG_USB_MICROTEK=m # # USB Network Adapters # CONFIG_USB_CATC=m CONFIG_USB_KAWETH=m CONFIG_USB_PEGASUS=m CONFIG_USB_RTL8150=m CONFIG_USB_USBNET_MII=m CONFIG_USB_USBNET=m CONFIG_USB_NET_AX8817X=m CONFIG_USB_NET_CDCETHER=m CONFIG_USB_NET_GL620A=m CONFIG_USB_NET_NET1080=m CONFIG_USB_NET_PLUSB=m # CONFIG_USB_NET_MCS7830 is not set CONFIG_USB_NET_RNDIS_HOST=m CONFIG_USB_NET_CDC_SUBSET=m CONFIG_USB_ALI_M5632=y CONFIG_USB_AN2720=y CONFIG_USB_BELKIN=y CONFIG_USB_ARMLINUX=y CONFIG_USB_EPSON2888=y CONFIG_USB_NET_ZAURUS=m CONFIG_USB_MON=y # # USB port drivers # CONFIG_USB_USS720=m # # USB Serial Converter support # CONFIG_USB_SERIAL=m CONFIG_USB_SERIAL_GENERIC=y # CONFIG_USB_SERIAL_AIRCABLE is not set CONFIG_USB_SERIAL_AIRPRIME=m CONFIG_USB_SERIAL_ARK3116=m CONFIG_USB_SERIAL_BELKIN=m CONFIG_USB_SERIAL_WHITEHEAT=m CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m CONFIG_USB_SERIAL_CP2101=m CONFIG_USB_SERIAL_CYPRESS_M8=m CONFIG_USB_SERIAL_EMPEG=m CONFIG_USB_SERIAL_FTDI_SIO=m CONFIG_USB_SERIAL_FUNSOFT=m CONFIG_USB_SERIAL_VISOR=m CONFIG_USB_SERIAL_IPAQ=m CONFIG_USB_SERIAL_IR=m CONFIG_USB_SERIAL_EDGEPORT=m CONFIG_USB_SERIAL_EDGEPORT_TI=m CONFIG_USB_SERIAL_GARMIN=m CONFIG_USB_SERIAL_IPW=m CONFIG_USB_SERIAL_KEYSPAN_PDA=m CONFIG_USB_SERIAL_KEYSPAN=m CONFIG_USB_SERIAL_KEYSPAN_MPR=y CONFIG_USB_SERIAL_KEYSPAN_USA28=y CONFIG_USB_SERIAL_KEYSPAN_USA28X=y CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y CONFIG_USB_SERIAL_KEYSPAN_USA19=y CONFIG_USB_SERIAL_KEYSPAN_USA18X=y CONFIG_USB_SERIAL_KEYSPAN_USA19W=y CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y CONFIG_USB_SERIAL_KEYSPAN_USA49W=y CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y CONFIG_USB_SERIAL_KLSI=m CONFIG_USB_SERIAL_KOBIL_SCT=m CONFIG_USB_SERIAL_MCT_U232=m # CONFIG_USB_SERIAL_MOS7720 is not set # CONFIG_USB_SERIAL_MOS7840 is not set CONFIG_USB_SERIAL_NAVMAN=m CONFIG_USB_SERIAL_PL2303=m CONFIG_USB_SERIAL_HP4X=m CONFIG_USB_SERIAL_SAFE=m CONFIG_USB_SERIAL_SAFE_PADDED=y CONFIG_USB_SERIAL_SIERRAWIRELESS=m CONFIG_USB_SERIAL_TI=m CONFIG_USB_SERIAL_CYBERJACK=m CONFIG_USB_SERIAL_XIRCOM=m CONFIG_USB_SERIAL_OPTION=m CONFIG_USB_SERIAL_OMNINET=m CONFIG_USB_EZUSB=y # # USB Miscellaneous drivers # CONFIG_USB_EMI62=m CONFIG_USB_EMI26=m # CONFIG_USB_ADUTUX is not set CONFIG_USB_AUERSWALD=m CONFIG_USB_RIO500=m CONFIG_USB_LEGOTOWER=m CONFIG_USB_LCD=m CONFIG_USB_LED=m # CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set # CONFIG_USB_PHIDGET is not set CONFIG_USB_IDMOUSE=m # CONFIG_USB_FTDI_ELAN is not set CONFIG_USB_APPLEDISPLAY=m CONFIG_USB_SISUSBVGA=m CONFIG_USB_SISUSBVGA_CON=y CONFIG_USB_LD=m # CONFIG_USB_TRANCEVIBRATOR is not set CONFIG_USB_TEST=m # # USB DSL modem support # CONFIG_USB_ATM=m CONFIG_USB_SPEEDTOUCH=m CONFIG_USB_CXACRU=m CONFIG_USB_UEAGLEATM=m CONFIG_USB_XUSBATM=m # # USB Gadget Support # # CONFIG_USB_GADGET is not set # # MMC/SD Card support # CONFIG_MMC=m # CONFIG_MMC_DEBUG is not set CONFIG_MMC_BLOCK=m CONFIG_MMC_SDHCI=m CONFIG_MMC_WBSD=m # CONFIG_MMC_TIFM_SD is not set # # LED devices # CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y # # LED drivers # # # LED Triggers # CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=m CONFIG_LEDS_TRIGGER_IDE_DISK=y CONFIG_LEDS_TRIGGER_HEARTBEAT=m # # InfiniBand support # # CONFIG_INFINIBAND is not set # # EDAC - error detection and reporting (RAS) (EXPERIMENTAL) # CONFIG_EDAC=y # # Reporting subsystems # # CONFIG_EDAC_DEBUG is not set CONFIG_EDAC_MM_EDAC=m # CONFIG_EDAC_AMD76X is not set # CONFIG_EDAC_E7XXX is not set CONFIG_EDAC_E752X=m # CONFIG_EDAC_I82875P is not set # CONFIG_EDAC_I82860 is not set # CONFIG_EDAC_R82600 is not set CONFIG_EDAC_POLL=y # # Real Time Clock # CONFIG_RTC_LIB=m CONFIG_RTC_CLASS=m # # RTC interfaces # CONFIG_RTC_INTF_SYSFS=m CONFIG_RTC_INTF_PROC=m CONFIG_RTC_INTF_DEV=m # CONFIG_RTC_INTF_DEV_UIE_EMUL is not set # # RTC drivers # CONFIG_RTC_DRV_X1205=m CONFIG_RTC_DRV_DS1307=m CONFIG_RTC_DRV_DS1553=m CONFIG_RTC_DRV_ISL1208=m CONFIG_RTC_DRV_DS1672=m CONFIG_RTC_DRV_DS1742=m CONFIG_RTC_DRV_PCF8563=m CONFIG_RTC_DRV_PCF8583=m CONFIG_RTC_DRV_RS5C372=m # CONFIG_RTC_DRV_M48T86 is not set # CONFIG_RTC_DRV_TEST is not set CONFIG_RTC_DRV_V3020=m # # DMA Engine support # CONFIG_DMA_ENGINE=y # # DMA Clients # CONFIG_NET_DMA=y # # DMA Devices # CONFIG_INTEL_IOATDMA=m # # File systems # CONFIG_EXT2_FS=y CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y CONFIG_EXT2_FS_SECURITY=y CONFIG_EXT2_FS_XIP=y CONFIG_FS_XIP=y CONFIG_EXT3_FS=m CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=m CONFIG_JBD_DEBUG=y CONFIG_FS_MBCACHE=y CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set CONFIG_REISERFS_PROC_INFO=y CONFIG_REISERFS_FS_XATTR=y CONFIG_REISERFS_FS_POSIX_ACL=y CONFIG_REISERFS_FS_SECURITY=y CONFIG_JFS_FS=m CONFIG_JFS_POSIX_ACL=y CONFIG_JFS_SECURITY=y # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set CONFIG_FS_POSIX_ACL=y CONFIG_XFS_FS=m CONFIG_XFS_QUOTA=y CONFIG_XFS_SECURITY=y CONFIG_XFS_POSIX_ACL=y # CONFIG_XFS_RT is not set CONFIG_GFS2_FS=m CONFIG_GFS2_FS_LOCKING_NOLOCK=m CONFIG_GFS2_FS_LOCKING_DLM=m CONFIG_OCFS2_FS=m # CONFIG_OCFS2_DEBUG_MASKLOG is not set CONFIG_MINIX_FS=m CONFIG_ROMFS_FS=m CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y CONFIG_QUOTA=y # CONFIG_QFMT_V1 is not set CONFIG_QFMT_V2=y CONFIG_QUOTACTL=y CONFIG_DNOTIFY=y CONFIG_AUTOFS_FS=m CONFIG_AUTOFS4_FS=m CONFIG_FUSE_FS=m # # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=y CONFIG_JOLIET=y CONFIG_ZISOFS=y CONFIG_ZISOFS_FS=y CONFIG_UDF_FS=m CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=m CONFIG_MSDOS_FS=m CONFIG_VFAT_FS=m CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="ascii" # CONFIG_NTFS_FS is not set # # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y CONFIG_RAMFS=y CONFIG_CONFIGFS_FS=m # # Miscellaneous filesystems # # CONFIG_ADFS_FS is not set CONFIG_AFFS_FS=m # CONFIG_ECRYPT_FS is not set CONFIG_HFS_FS=m CONFIG_HFSPLUS_FS=m CONFIG_BEFS_FS=m # CONFIG_BEFS_DEBUG is not set CONFIG_BFS_FS=m CONFIG_EFS_FS=m # CONFIG_JFFS_FS is not set CONFIG_JFFS2_FS=m CONFIG_JFFS2_FS_DEBUG=0 CONFIG_JFFS2_FS_WRITEBUFFER=y CONFIG_JFFS2_SUMMARY=y # CONFIG_JFFS2_FS_XATTR is not set # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set CONFIG_JFFS2_ZLIB=y CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set CONFIG_CRAMFS=m CONFIG_VXFS_FS=m # CONFIG_HPFS_FS is not set CONFIG_QNX4FS_FS=m CONFIG_SYSV_FS=m CONFIG_UFS_FS=m # CONFIG_UFS_FS_WRITE is not set # CONFIG_UFS_DEBUG is not set # # Network File Systems # CONFIG_NFS_FS=m CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y CONFIG_NFS_V4=y CONFIG_NFS_DIRECTIO=y CONFIG_NFSD=m CONFIG_NFSD_V2_ACL=y CONFIG_NFSD_V3=y CONFIG_NFSD_V3_ACL=y CONFIG_NFSD_V4=y CONFIG_NFSD_TCP=y CONFIG_LOCKD=m CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=m CONFIG_NFS_ACL_SUPPORT=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=m CONFIG_SUNRPC_GSS=m CONFIG_RPCSEC_GSS_KRB5=m CONFIG_RPCSEC_GSS_SPKM3=m # CONFIG_SMB_FS is not set CONFIG_CIFS=m # CONFIG_CIFS_STATS is not set CONFIG_CIFS_WEAK_PW_HASH=y CONFIG_CIFS_XATTR=y CONFIG_CIFS_POSIX=y # CONFIG_CIFS_DEBUG2 is not set # CONFIG_CIFS_EXPERIMENTAL is not set CONFIG_NCP_FS=m CONFIG_NCPFS_PACKET_SIGNING=y CONFIG_NCPFS_IOCTL_LOCKING=y CONFIG_NCPFS_STRONG=y CONFIG_NCPFS_NFS_NS=y CONFIG_NCPFS_OS2_NS=y CONFIG_NCPFS_SMALLDOS=y CONFIG_NCPFS_NLS=y CONFIG_NCPFS_EXTRAS=y CONFIG_CODA_FS=m # CONFIG_CODA_FS_OLD_API is not set # CONFIG_AFS_FS is not set CONFIG_9P_FS=m # # Partition Types # CONFIG_PARTITION_ADVANCED=y # CONFIG_ACORN_PARTITION is not set CONFIG_OSF_PARTITION=y CONFIG_AMIGA_PARTITION=y # CONFIG_ATARI_PARTITION is not set CONFIG_MAC_PARTITION=y CONFIG_MSDOS_PARTITION=y CONFIG_BSD_DISKLABEL=y CONFIG_MINIX_SUBPARTITION=y CONFIG_SOLARIS_X86_PARTITION=y CONFIG_UNIXWARE_DISKLABEL=y # CONFIG_LDM_PARTITION is not set CONFIG_SGI_PARTITION=y # CONFIG_ULTRIX_PARTITION is not set CONFIG_SUN_PARTITION=y CONFIG_KARMA_PARTITION=y CONFIG_EFI_PARTITION=y # # Native Language Support # CONFIG_NLS=y CONFIG_NLS_DEFAULT="utf8" CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_CODEPAGE_737=m CONFIG_NLS_CODEPAGE_775=m CONFIG_NLS_CODEPAGE_850=m CONFIG_NLS_CODEPAGE_852=m CONFIG_NLS_CODEPAGE_855=m CONFIG_NLS_CODEPAGE_857=m CONFIG_NLS_CODEPAGE_860=m CONFIG_NLS_CODEPAGE_861=m CONFIG_NLS_CODEPAGE_862=m CONFIG_NLS_CODEPAGE_863=m CONFIG_NLS_CODEPAGE_864=m CONFIG_NLS_CODEPAGE_865=m CONFIG_NLS_CODEPAGE_866=m CONFIG_NLS_CODEPAGE_869=m CONFIG_NLS_CODEPAGE_936=m CONFIG_NLS_CODEPAGE_950=m CONFIG_NLS_CODEPAGE_932=m CONFIG_NLS_CODEPAGE_949=m CONFIG_NLS_CODEPAGE_874=m CONFIG_NLS_ISO8859_8=m CONFIG_NLS_CODEPAGE_1250=m CONFIG_NLS_CODEPAGE_1251=m CONFIG_NLS_ASCII=y CONFIG_NLS_ISO8859_1=m CONFIG_NLS_ISO8859_2=m CONFIG_NLS_ISO8859_3=m CONFIG_NLS_ISO8859_4=m CONFIG_NLS_ISO8859_5=m CONFIG_NLS_ISO8859_6=m CONFIG_NLS_ISO8859_7=m CONFIG_NLS_ISO8859_9=m CONFIG_NLS_ISO8859_13=m CONFIG_NLS_ISO8859_14=m CONFIG_NLS_ISO8859_15=m CONFIG_NLS_KOI8_R=m CONFIG_NLS_KOI8_U=m CONFIG_NLS_UTF8=m # # Distributed Lock Manager # CONFIG_DLM=m CONFIG_DLM_DEBUG=y # # Instrumentation Support # CONFIG_PROFILING=y CONFIG_OPROFILE=m CONFIG_KPROBES=y # # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y # CONFIG_PRINTK_TIME is not set CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_IPIPE_DEBUG is not set CONFIG_IPIPE_TRACE_ENABLE_VALUE=0 CONFIG_DEBUG_KERNEL=y CONFIG_LOG_BUF_SHIFT=17 CONFIG_DETECT_SOFTLOCKUP=y CONFIG_SCHEDSTATS=y # CONFIG_DEBUG_SLAB is not set # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set CONFIG_DEBUG_SPINLOCK=y # CONFIG_DEBUG_MUTEXES is not set # CONFIG_DEBUG_RWSEMS is not set # CONFIG_DEBUG_LOCK_ALLOC is not set # CONFIG_PROVE_LOCKING is not set CONFIG_DEBUG_SPINLOCK_SLEEP=y # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y CONFIG_DEBUG_FS=y # CONFIG_DEBUG_VM is not set CONFIG_DEBUG_LIST=y # CONFIG_FRAME_POINTER is not set CONFIG_UNWIND_INFO=y CONFIG_STACK_UNWIND=y # CONFIG_FORCED_INLINING is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_LKDTM is not set CONFIG_EARLY_PRINTK=y CONFIG_DEBUG_STACKOVERFLOW=y # CONFIG_DEBUG_STACK_USAGE is not set CONFIG_DEBUG_RODATA=y # CONFIG_4KSTACKS is not set CONFIG_X86_FIND_SMP_CONFIG=y CONFIG_X86_MPPARSE=y CONFIG_DOUBLEFAULT=y # # Security options # CONFIG_KEYS=y CONFIG_KEYS_DEBUG_PROC_KEYS=y CONFIG_SECURITY=y CONFIG_SECURITY_NETWORK=y # CONFIG_SECURITY_NETWORK_XFRM is not set CONFIG_SECURITY_CAPABILITIES=y # CONFIG_SECURITY_ROOTPLUG is not set CONFIG_SECURITY_SELINUX=y CONFIG_SECURITY_SELINUX_BOOTPARAM=y CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=1 CONFIG_SECURITY_SELINUX_DISABLE=y CONFIG_SECURITY_SELINUX_DEVELOP=y CONFIG_SECURITY_SELINUX_AVC_STATS=y CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE=1 # CONFIG_SECURITY_SELINUX_ENABLE_SECMARK_DEFAULT is not set # CONFIG_SECURITY_SELINUX_POLICYDB_VERSION_MAX is not set # # Cryptographic options # CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=m CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_HMAC=y CONFIG_CRYPTO_NULL=m CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=m CONFIG_CRYPTO_SHA1=y CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m CONFIG_CRYPTO_WP512=m CONFIG_CRYPTO_TGR192=m CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=m CONFIG_CRYPTO_DES=m CONFIG_CRYPTO_BLOWFISH=m CONFIG_CRYPTO_TWOFISH=m CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_TWOFISH_586 is not set CONFIG_CRYPTO_SERPENT=m CONFIG_CRYPTO_AES=m # CONFIG_CRYPTO_AES_586 is not set CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_ANUBIS=m CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=y # CONFIG_CRYPTO_TEST is not set # # Hardware crypto devices # CONFIG_CRYPTO_DEV_PADLOCK=m CONFIG_CRYPTO_DEV_PADLOCK_AES=m CONFIG_CRYPTO_DEV_PADLOCK_SHA=m # # Library routines # CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC32=y CONFIG_LIBCRC32C=y CONFIG_AUDIT_GENERIC=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=m CONFIG_REED_SOLOMON=m CONFIG_REED_SOLOMON_DEC16=y CONFIG_TEXTSEARCH=y CONFIG_TEXTSEARCH_KMP=m CONFIG_TEXTSEARCH_BM=m CONFIG_TEXTSEARCH_FSM=m CONFIG_PLIST=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GENERIC_PENDING_IRQ=y CONFIG_X86_SMP=y CONFIG_X86_HT=y CONFIG_X86_BIOS_REBOOT=y CONFIG_X86_TRAMPOLINE=y CONFIG_KTIME_SCALAR=y ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-08 15:11 ` Eric Noulard @ 2007-02-08 15:32 ` Jan Kiszka 2007-02-09 16:49 ` Eric Noulard 0 siblings, 1 reply; 19+ messages in thread From: Jan Kiszka @ 2007-02-08 15:32 UTC (permalink / raw) To: Eric Noulard; +Cc: Xenomai help [-- Attachment #1: Type: text/plain, Size: 3009 bytes --] Eric Noulard wrote: > 2007/2/7, Jan Kiszka <jan.kiszka@domain.hid>: >> >> Your /proc/interrupts output already suggests it: CONFIG_PCI_MSI is set >> in your config. It's worth trying the disable it, because even plain >> Linux has problems with certain board/device combinations. But I don't >> recall if tg3 was recently involved in such, it may still be an ipipe >> bug here. > > The same xenomai patched kernel with CONFIG_PCI_MSI disable > boots fine with following /proc/interrupt: > ========== > CPU0 CPU1 > 0: 2169593 0 IO-APIC-edge timer, rthal_broadcast_timer > 1: 2 0 IO-APIC-edge i8042 > 2: 0 0 XT-PIC-XT cascade > 8: 1 0 IO-APIC-edge rtc > 12: 4 0 IO-APIC-edge i8042 > 14: 18945 0 IO-APIC-edge ide0 > 16: 26920 0 IO-APIC-fasteoi eth0, eth1 > 20: 12861 0 IO-APIC-fasteoi uhci_hcd:usb1, > ehci_hcd:usb4, libata > 21: 0 0 IO-APIC-fasteoi uhci_hcd:usb2 > 22: 10967 0 IO-APIC-fasteoi uhci_hcd:usb3 > NMI: 0 0 > LOC: 2169430 2169431 > ERR: 0 > MIS: 0 > ========== > > The former kernel used with kernel boot parameter "nomsi" continues > to hang despite the boot parameter for "nomsi". > I did go back to http://www.xenomai.org/index.php/FAQs > and saw informations about SMI > "On some systems, SMI may be involved in thermal throttling of the > CPU. Thus, switching it off can cause hardware damage in overheat > scenarios." > > Now I'm lost with those 3 letters acronyms :(( > Does SMI has something to do with MSI or not? You can form both acronyms using the same set of letters, that's all. > > In both cases (SMI related to MSI or not) > How can I know if SMI is used for thermal throttling on my box? Unless you over-clock your system, or save cooling equipment, there is practically no problem. AFAIK, no one experienced damage from overheat so far while SMI was disabled. Still there is a theoretical risk, therefore we warn. > > I have the same boot problem with cpus=1 and the first kenrel (SMI enabled) > (the box hangs on ifup eth0). > > Now with the "bootable" xenomai-kernel config > I go on and give a try to launch xeno-test (with no option at all), > and it hangs the box the near the: > "cat /proc/xenomai/rtdm/protocol_devices" > message Sounds like !MSI just moves the bug around. > > Where should I look in order to investigate this hang. > > I attached the .config corresponding to bootable but hangable kernel. Can you attach a serial console to your system (see linux/Documentation/serial-console.txt) and grab the full kernel log up to the hang? Maybe we have an oops that just cannot come out anymore. Even if not, you could then try to instrument (printk) the kernel towards the faulting lines. Jan [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 250 bytes --] ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-08 15:32 ` Jan Kiszka @ 2007-02-09 16:49 ` Eric Noulard 2007-02-09 17:03 ` Gilles Chanteperdrix 0 siblings, 1 reply; 19+ messages in thread From: Eric Noulard @ 2007-02-09 16:49 UTC (permalink / raw) To: Jan Kiszka; +Cc: Xenomai help [-- Attachment #1: Type: text/plain, Size: 1231 bytes --] 2007/2/8, Jan Kiszka <jan.kiszka@domain.hid>: > > Can you attach a serial console to your system (see > linux/Documentation/serial-console.txt) and grab the full kernel log up > to the hang? Here you go. I recompile a linux 2.6.19 + adeos-ipipe-2.6.19-i386-1.7-01.patch for xenomai 2.3 in order to avoid to look at may be previous ipipe bugs. I did: 1- attached the serial console 2- login on serial console as root 3- launch xeno-test (no args) Then the machine freeze.... > Maybe we have an oops that just cannot come out anymore. No oops anywhere :((( > Even if not, you could then try to instrument (printk) the kernel > towards the faulting lines. I may try that but I really don't know where to printk :(( Moreover I'm in my early days of kernel-side dev'. Any advice as a starting point? Is it valulable for me to go on with 2.6.19 kernel or should I switch to 2.6.20 (or go back for older kernel 2.6.17?). I recently read nasty filesystem corruption issue on 2.6.19. Is the 2.6.20 ipipe patch (rhttp://download.gna.org/adeos/patches/v2.6/i386/adeos-ipipe-2.6.20-i386-1.7-01.patch) eady to use if I switch to SVN version of Xenomai. What could be the more helpful road for you (and for me of course :))? -- Erk [-- Warning: decoded text below may be mangled, UTF-8 assumed --] [-- Attachment #2: xeno-2.3-ipipe-1.7-0-bootandhang.txt --] [-- Type: text/plain; name=xeno-2.3-ipipe-1.7-0-bootandhang.txt; charset=ANSI_X3.4-1968, Size: 36086 bytes --] Press any key to continue. Press any key to continue. Press any key to continue. GNU GRUB version 0.97 (640K lower / 2095872K upper memory) +-------------------------------------------------------------------------+||||||||||||||||||||||||+-------------------------------------------------------------------------+ Use the ^ and v keys to select which entry is highlighted. Press enter to boot the selected OS, 'e' to edit the commands before booting, 'a' to modify the kernel arguments before booting, or 'c' for a command-line. Fedora Core (2.6.20-rc6.1.rt1.0098) [32bits] Fedora Core (2.6.18-1.2798.fc6) [32bits] Fedora Core (2.6.19-xeno-2.3-ipipe-1.7-0) [32bits] Fedora Core (2.6.19-xenomai-2.3-noSMI) [32bits] Fedora Core (2.6.19-vanilla) [32bits] Fedora Core (2.6.18-1.2798.fc6) [64bits] Fedora Core (2.6.20-rc6.1.rt1.0098) [64bits] The highlighted entry will be booted automatically in 30 seconds. The highlighted entry will be booted automatically in 29 seconds. The highlighted entry will be booted automatically in 28 seconds. The highlighted entry will be booted automatically in 27 seconds. The highlighted entry will be booted automatically in 26 seconds. Fedora Core (2.6.19-xeno-2.3-ipipe-1.7-0) [32bits] Fedora Core (2.6.18-1.2798.fc6) [32bits] Fedora Core (2.6.18-1.2798.fc6) [32bits] Fedora Core (2.6.20-rc6.1.rt1.0098) [32bits] Fedora Core (2.6.20-rc6.1.rt1.0098) [32bits] Fedora Core (2.6.18-1.2798.fc6) [32bits] Fedora Core (2.6.18-1.2798.fc6) [32bits] Fedora Core (2.6.19-xeno-2.3-ipipe-1.7-0) [32bits] Booting 'Fedora Core (2.6.19-xeno-2.3-ipipe-1.7-0) [32bits]' root (hd0,0) Filesystem type is ext2fs, partition type 0x83 kernel /ix86/vmlinuz-2.6.19-xeno-2.3-ipipe-1.7-0 ro root=LABEL=/1 console=tty0 console=ttyS0,115200 [Linux-bzImage, setup=0x1e00, size=0x1d348a] initrd /ix86/initrd-2.6.19-xeno-2.3-ipipe-1.7-0.img [Linux-initrd @ 0x37e7a000, 0x1750bc bytes] Linux version 2.6.19-xeno-2.3-ipipe-1.7-01 (myhost) (version gcc 4.1.1 20061011 (Red Hat 4.1.1-30)) #1 SMP Fri Feb 9 10:45:31 CET 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 0000000000100000 - 000000007ffc0000 (usable) BIOS-e820: 000000007ffc0000 - 000000007ffcfc00 (ACPI data) BIOS-e820: 000000007ffcfc00 - 000000007ffff000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved) BIOS-e820: 00000000fed13000 - 00000000feda0000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) Warning only 896MB will be used. Use a HIGHMEM enabled kernel. 896MB LOWMEM available. found SMP MP-table at 000fe710 Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 early_node_map[1] active PFN ranges 0: 0 -> 229376 DMI 2.4 present. ACPI: PM-Timer IO Port: 0x808 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x03] address[0xfec10000] gsi_base[32]) IOAPIC[1]: apic_id 3, version 32, address 0xfec10000, GSI 32-55 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Enabling APIC mode: Flat. Using 2 I/O APICs ACPI: HPET id: 0xffffffff base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 80000000 (gap: 7ffff000:70001000) Detected 1866.841 MHz processor. Built 1 zonelists. Total pages: 227136 Kernel command line: ro root=LABEL=/1 console=tty0 console=ttyS0,115200 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) I-pipe 1.7-01: pipeline enabled. Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 790504k/917504k available (2229k kernel code, 126408k reserved, 99279k data, 200k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfffb7000 - 0xfffff000 ( 288 kB) vmalloc : 0xf8800000 - 0xfffb5000 ( 119 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc6482000 - 0xc64b4000 ( 200 kB) .data : 0xc032d796 - 0xc6421434 (99279 kB) .text : 0xc0100000 - 0xc032d796 (2229 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Using HPET for base-timer Calibrating delay using timer specific routine.. 3740.57 BogoMIPS (lpj=1870285) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 monitor/mwait feature present. using mwait in idle threads. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20060707 CPU0: Intel(R) Xeon(R) CPU 3040 @ 1.86GHz stepping 06 SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 3733.58 BogoMIPS (lpj=1866790) monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel(R) Xeon(R) CPU 3040 @ 1.86GHz stepping 06 Total of 2 processors activated (7474.15 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs migration_cost=58 checking if image is initramfs... it is Freeing initrd memory: 1492k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 0880-08bf claimed by ICH6 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: PXH quirk detected, disabling MSI for SHPC device PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 *6 7 9 10 11 12) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default PCI: Bridge: 0000:00:01.0 IO window: e000-efff MEM window: fe900000-feafffff PREFETCH window: disabled. PCI: Bridge: 0000:02:00.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: fe800000-fe8fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: d000-dfff MEM window: fe600000-fe7fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.5 IO window: c000-cfff MEM window: fe400000-fe5fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: b000-bfff MEM window: fe200000-fe3fffff PREFETCH window: e8000000-efffffff ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 21 (level, low) -> IRQ 17 ACPI: PCI Interrupt 0000:00:1c.4[B] -> GSI 22 (level, low) -> IRQ 18 ACPI: PCI Interrupt 0000:00:1c.5[C] -> GSI 23 (level, low) -> IRQ 19 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 9, 2621440 bytes) TCP bind hash table entries: 65536 (order: 8, 1310720 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered audit: initializing netlink socket (disabled) audit(1171038391.102:1): initialized I-pipe: Domain Xenomai registered. Xenomai: hal/x86 started. I-pipe: Domain IShield registered. Xenomai: real-time nucleus v2.3 (Baroque) loaded. Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Power Button (FF) [PWRF] Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled ÿserial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH7: IDE controller at PCI slot 0000:00:1f.1 ACPI: Unable to derive IRQ for device 0000:00:1f.1 ACPI: PCI Interrupt 0000:00:1f.1[A]: no GSI ICH7: chipset revision 1 ICH7: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio hda: HL-DT-STCD-RW/DVD-ROM GCC-4244N, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide-floppy driver 0.99.newide usbcore: registered new interface driver libusual usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid /home/cnes/Kernels/32bits/linux-2.6.19-xeno-2.3-ipipe-1.7-01/drivers/usb/input/hid-core.c: v2.6:USB HID core driver serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice TCP bic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Starting balanced_irq Using IPI No-Shortcut mode Time: tsc clocksource has been installed. ACPI: (supports S0 S4 S5) Freeing unused kernel memory: 200k freed Write protecting the kernel read-only data: 388k Red Hat nash version 5.1.19 starting Mounting proc filesystem Mounting sysfs filesystem Creating /dev Creating initial device nodes Setting up hotplug. Creating block device nodes. Loading uhci-hcd.ko module USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000ace0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 17 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000acc0 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000aca0 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected Loading ohci-hcd.ko module Loading ehci-hcd.ko module ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfeb00400 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected usb 2-1: new full speed USB device using uhci_hcd and address 2 Loading jbd.ko module Loading ext3.ko module Loading scsi_mod.ko module SCSI subsystem initialized Loading sd_mod.ko module Loading libata.ko module Loading ata_generic.ko module Loading ata_piix.ko module ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 20 (level, low) -> IRQ 20 ata1: SATA max UDMA/133 cmd 0xAC98 ctl 0xAC92 bmdma 0xAC60 irq 20 ata2: SATA max UDMA/133 cmd 0xAC80 ctl 0xAC7A bmdma 0xAC68 irq 20 scsi0 : ata_piix ata1.00: ATA-7, max UDMA/133, 156250000 sectors: LBA48 NCQ (depth 0/32) ata1.00: ata1: dev 0 multi count 8 ata1.00: configured for UDMA/133 scsi1 : ata_piix usb 4-3: new high speed USB device using ehci_hcd and address 2 usb 4-3: configuration #1 chosen from 1 choice hub 4-3:1.0: USB hub found hub 4-3:1.0: 4 ports detected ata2.00: ATA-7, max UDMA/133, 156250000 sectors: LBA48 NCQ (depth 0/32) ata2.00: ata2: dev 0 multi count 8 ata2.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD800JD-75MS 10.0 PQ: 0 ANSI: 5 SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB) sda: Write Protect is off SCSI device sda: drive cache: write back SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB) sda: Write Protect is off SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 < sda5 sda6 > sd 0:0:0:0: Attached scsi disk sda scsi 1:0:0:0: Direct-Access ATA WDC WD800JD-75MS 10.0 PQ: 0 ANSI: 5 SCSI device sdb: 156250000 512-byte hdwr sectors (80000 MB) sdb: Write Protect is off SCSI device sdb: drive cache: write back SCSI device sdb: 156250000 512-byte hdwr sectors (80000 MB) sdb: Write Protect is off SCSI device sdb: drive cache: write back sdb: sdb1 sd 1:0:0:0: Attached scsi disk sdb Creating root device. Mounting root filesystem. usb 3-1: new low speed USB device using uhci_hcd and address 2 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Setting up other filesystems. Setting up new root fs no fstab.sys, mounting internal defaults Switching to new root and running init. unmounting old /dev unmounting old /proc unmounting old /sys usb 3-1: configuration #1 chosen from 1 choice input: Logitech Optical USB Mouse as /class/input/input0 input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.2-1 usb 3-2: new low speed USB device using uhci_hcd and address 3 usb 3-2: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /class/input/input1 input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.2-2 SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks audit(1171038397.381:2): selinux=0 auid=4294967295 INIT: version 2.86 booting Welcome to Fedora Core Press 'I' to enter interactive startup. Configuraton de l'horloge (utc) : ven fév 9 17:26:40 CET 2007 [ OK ] Démarrage de udev :[ OK ] Chargement de la configuration clavier par défaut (fr-latin1) :[ OK ] Configuration du nom d'hôte myhost: [ OK ] No devices found Configuration du gestionnaire de volume logique : No volume groups found [ OK ] Vérification des systèmes de fichiers Vérification de tous les systèmes de fichiers. [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/sda2 /1: clean, 149590/2560864 files, 1337190/2560359 blocks [/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -a /dev/sda1 [/sbin/fsck.ext3 (2) -- /data] fsck.ext3 -a /dev/sdb1 /boot: clean, 66/1280000 files, 84309/1279167 blocks [/sbin/fsck.ext3 (2) -- /home] fsck.ext3 -a /dev/sda6 /data: clean, 11/19543392 files, 658058/19531015 blocks /home: clean, 127526/12091392 files, 2115664/12082880 blocks [/sbin/fsck.ext3 (1) -- /slash_64bits] fsck.ext3 -a /dev/sda3 /slash_64bits: clean, 141455/2560864 files, 1028229/2560359 blocks [ OK ] Remontage du système de fichiers racine en mode lecture-écriture : [ OK ] Montage des systèmes de fichiers locaux : [ OK ] Activation des quotas des systèmes de fichiers locaux : [ OK ] Activation des /etc/fstab swaps : [ OK ] INIT: Entering runlevel: 5 Début du démarrage non-interactif Démarrage de la réactivation en arrière plan :[ OK ] Vérification des changements de matériel [ OK ] Activation de l'interface loopback : [ OK ] Activation de l'interface eth0 : [ OK ] Activation de l'interface eth1 : [ OK ] Démarrage de l'enregistreur chronologique du système :[ OK ] Démarrage de l'enregistreur chronologique du noyau :[ OK ] Démarrage de irqbalance :[ OK ] Démarrage de portmap :[ OK ] Démarrage de NFS statd :[ OK ] Démarrage de RPC idmapd :[ OK ] Démarrage du bus de messages du système :[ OK ] Démarrage des services Bluetooth :[ OK ][ OK ] Montage d'autres sytèmes de fichiers : [ OK ] Démarrage du démon PC/SC smart card (pcscd) :[ OK ] Démarrage de hidd :[ OK ] Configuration du nom de domaine NIS mynisdomain : [ OK ] Lien au domaine NIS :[ OK ] Attente d'un serveur de domaine NIS. Démarrage de autofs : Loading autofs4: [ OK ] Démarrage de automount :[ OK ] [ OK ] Démarrage du démon acpi :[ OK ] Démarrage de hpiod :[ OK ] Démarrage de hpssd :[ OK ] Démarrage de cups :[ OK ] Démarrage de sshd :[ OK ] Démarrage de ntpd :[ OK ] Démarrage de sendmail :[ OK ] Démarrage de sm-client :[ OK ] Démarrage des services de souris de la console :[ OK ] Démarrage de crond :[ OK ] Démarrage de xfs :[ OK ] Démarrage de anacron :[ OK ] Démarrage de atd :[ OK ] Démarrage de la réactivation en arrière plan :[ OK ] Démarrage du démon Avahi :[ OK ] Démarrage du démon HAL :[ OK ] Démarrage de smartd :[ OK ] Fedora Core release 6 (Zod) Kernel 2.6.19-xeno-2.3-ipipe-1.7-01 on an i686 Serial Console Login:root Password: Last login: Fri Feb 9 17:25:13 on ttyS0 [root@myhost ~]# xeno-test xeno-test: started withBusybox is 0 xeno-test: running tests ven fév 9 17:27:59 CET 2007 running: /usr/xenomai/bin/xeno-config --verbose xeno-config --verbose --version="2.3" --cc="gcc" --arch="i386" --prefix="/usr/xenomai" --xeno-cflags="-I/usr/xenomai/include -D_GNU_SOURCE -D_REENTRANT" --xeno-ldflags="-L/usr/xenomai/lib -lpthread " --posix-cflags="-I/usr/xenomai/include -I/usr/xenomai/include/posix -D_GNU_SOURCE -D_REENTRANT -D__XENO__" --posix-ldflags="-L/usr/xenomai/lib -lpthread_rt -lpthread -lrt " --library-dir="/usr/xenomai/lib" ven fév 9 17:27:59 CET 2007 running: /usr/xenomai/bin/xeno-info If some fields are empty or look unusual you may have an old version. Compare to the current minimal requirements in Documentation/Changes. Linux myhost 2.6.19-xeno-2.3-ipipe-1.7-01 #1 SMP Fri Feb 9 10:45:31 CET 2007 i686 i686 i386 GNU/Linux Gnu C 4.1.1 Gnu make 3.81 util-linux pre6) mount pre6) module-init-tools 3.3-pre1 e2fsprogs 1.39 PPP 2.4.4 isdn4k-utils 3.9 Linux C Library > libc.2.5 Dynamic linker (ldd) 2.5 Procps 3.2.7 Net-tools 1.60 Kbd 1.12 Sh-utils 5.97 Modules Loaded autofs4 hidp rfcomm l2cap bluetooth sunrpc ipv6 dm_mirror dm_multipath dm_mod parport_pc lp parport sg shpchp pcspkr i2c_i801 ide_cd i2c_core serio_raw cdrom tg3 ata_piix ata_generic libata sd_mod scsi_mod ext3 jbd ehci_hcd ohci_hcd uhci_hcd ven fév 9 17:27:59 CET 2007 running: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Xeon(R) CPU 3040 @ 1.86GHz stepping : 6 cpu MHz : 1866.841 cache size : 2048 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr lahf_lm bogomips : 3740.57 processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Xeon(R) CPU 3040 @ 1.86GHz stepping : 6 cpu MHz : 1866.841 cache size : 2048 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr lahf_lm bogomips : 3733.58 ven fév 9 17:28:00 CET 2007 running: md5sum /proc/cpuinfo # cpuinfo fingerprint fbfe7a0011957632fb2af6e2a726bd98 /proc/cpuinfo # CONFIG_PREEMPT_NONE is not set CONFIG_PREEMPT_VOLUNTARY=y # CONFIG_PREEMPT is not set CONFIG_PREEMPT_BKL=y CONFIG_IPIPE=y CONFIG_PM=y CONFIG_PM_LEGACY=y # CONFIG_PM_DEBUG is not set # CONFIG_PM_SYSFS_DEPRECATED is not set CONFIG_ACPI=y CONFIG_ACPI_SLEEP=y CONFIG_ACPI_SLEEP_PROC_FS=y # CONFIG_ACPI_SLEEP_PROC_SLEEP is not set CONFIG_ACPI_AC=y CONFIG_ACPI_BATTERY=y CONFIG_ACPI_BUTTON=y # CONFIG_ACPI_VIDEO is not set # CONFIG_ACPI_HOTKEY is not set CONFIG_ACPI_FAN=y # CONFIG_ACPI_DOCK is not set # CONFIG_ACPI_PROCESSOR is not set # CONFIG_ACPI_ASUS is not set # CONFIG_ACPI_IBM is not set # CONFIG_ACPI_TOSHIBA is not set CONFIG_ACPI_BLACKLIST_YEAR=0 # CONFIG_ACPI_DEBUG is not set CONFIG_ACPI_EC=y CONFIG_ACPI_POWER=y CONFIG_ACPI_SYSTEM=y # CONFIG_ACPI_CONTAINER is not set # CONFIG_ACPI_SBS is not set # CONFIG_CPU_FREQ is not set CONFIG_IPIPE_DEBUG=y CONFIG_IPIPE_TRACE=y CONFIG_IPIPE_TRACE_ENABLE=y CONFIG_IPIPE_TRACE_MCOUNT=y CONFIG_IPIPE_TRACE_IRQSOFF=y CONFIG_IPIPE_TRACE_SHIFT=14 # CONFIG_IPIPE_TRACE_VMALLOC is not set CONFIG_IPIPE_TRACE_ENABLE_VALUE=1 CONFIG_DEBUG_SPINLOCK=y CONFIG_DEBUG_SPINLOCK_SLEEP=y ven fév 9 17:28:00 CET 2007 running: cat /proc/ipipe/IShield +----- Handling ([A]ccepted, [G]rabbed, [W]ired, [D]iscarded) |+---- Sticky ||+--- Locked |||+-- Exclusive ||||+- Virtual [IRQ] ||||| 0: G.... 1: G.... 2: G.... 3: G.... 4: G.... 5: G.... 6: G.... 7: G.... 8: G.... 9: G.... 10: G.... 11: G.... 12: G.... 13: G.... 14: G.... 15: G.... 16: G.... 17: G.... 18: G.... 19: G.... 20: G.... 21: G.... 22: G.... 23: G.... 24: G.... 25: G.... 26: G.... 27: G.... 28: G.... 29: G.... 30: G.... 31: G.... 32: G.... 33: G.... 34: G.... 35: G.... 36: G.... 37: G.... 38: G.... 39: G.... 40: G.... 41: G.... 42: G.... 43: G.... 44: G.... 45: G.... 46: G.... 47: G.... 48: G.... 49: G.... 50: G.... 51: G.... 52: G.... 53: G.... 54: G.... 55: G.... 56: G.... 57: G.... 58: G.... 59: G.... 60: G.... 61: G.... 62: G.... 63: G.... 64: G.... 65: G.... 66: G.... 67: G.... 68: G.... 69: G.... 70: G.... 71: G.... 72: G.... 73: G.... 74: G.... 75: G.... 76: G.... 77: G.... 78: G.... 79: G.... 80: G.... 81: G.... 82: G.... 83: G.... 84: G.... 85: G.... 86: G.... 87: G.... 88: G.... 89: G.... 90: G.... 91: G.... 92: G.... 93: G.... 94: G.... 95: G.... 96: G.... 97: G.... 98: G.... 99: G.... 100: G.... 101: G.... 102: G.... 103: G.... 104: G.... 105: G.... 106: G.... 107: G.... 108: G.... 109: G.... 110: G.... 111: G.... 112: G.... 113: G.... 114: G.... 115: G.... 116: G.... 117: G.... 118: G.... 119: G.... 120: G.... 121: G.... 122: G.... 123: G.... 124: G.... 125: G.... 126: G.... 127: G.... 128: G.... 129: G.... 130: G.... 131: G.... 132: G.... 133: G.... 134: G.... 135: G.... 136: G.... 137: G.... 138: G.... 139: G.... 140: G.... 141: G.... 142: G.... 143: G.... 144: G.... 145: G.... 146: G.... 147: G.... 148: G.... 149: G.... 150: G.... 151: G.... 152: G.... 153: G.... 154: G.... 155: G.... 156: G.... 157: G.... 158: G.... 159: G.... 160: G.... 161: G.... 162: G.... 163: G.... 164: G.... 165: G.... 166: G.... 167: G.... 168: G.... 169: G.... 170: G.... 171: G.... 172: G.... 173: G.... 174: G.... 175: G.... 176: G.... 177: G.... 178: G.... 179: G.... 180: G.... 181: G.... 182: G.... 183: G.... 184: G.... 185: G.... 186: G.... 187: G.... 188: G.... 189: G.... 190: G.... 191: G.... 192: G.... 193: G.... 194: G.... 195: G.... 196: G.... 197: G.... 198: G.... 199: G.... 200: G.... 201: G.... 202: G.... 203: G.... 204: G.... 205: G.... 206: G.... 207: G.... 208: G.... 209: G.... 210: G.... 211: G.... 212: G.... 213: G.... 214: G.... 215: G.... 216: G.... 217: GS... 218: G.... 219: G.... 220: G.... 221: G.... 222: G.... 223: G.... [Domain info] id=0x53484c44 priority=150 ven fév 9 17:28:00 CET 2007 running: cat /proc/ipipe/Linux +----- Handling ([A]ccepted, [G]rabbed, [W]ired, [D]iscarded) |+---- Sticky ||+--- Locked |||+-- Exclusive ||||+- Virtual [IRQ] ||||| 0: A.... 1: A.... 2: A.L.. 3: A.... 4: A.... 5: A.... 6: A.... 7: A.... 8: A.... 9: A.... 10: A.... 11: A.... 12: A.... 13: A.... 14: A.... 15: A.... 16: A.... 17: A.... 18: A.... 19: A.L.. 20: A.... 21: A.... 22: A.... 23: A.... 24: A.... 25: A.... 26: A.... 27: A.... 28: A.... 29: A.... 30: A.... 31: A.... 32: A.... 33: A.... 34: A.... 35: A.... 36: A.... 37: A.... 38: A.... 39: A.... 40: A.... 41: A.... 42: A.... 43: A.... 44: A.... 45: A.... 46: A.... 47: A.... 48: A.... 49: A.... 50: A.... 51: A.... 52: A.... 53: A.... 54: A.... 55: A.... 56: A.... 57: A.... 58: A.... 59: A.... 60: A.... 61: A.... 62: A.... 63: A.... 64: A.... 65: A.... 66: A.... 67: A.... 68: A.... 69: A.... 70: A.... 71: A.... 72: A.... 73: A.... 74: A.... 75: A.... 76: A.... 77: A.... 78: A.... 79: A.... 80: A.... 81: A.... 82: A.... 83: A.... 84: A.... 85: A.... 86: A.... 87: A.... 88: A.... 89: A.... 90: A.... 91: A.... 92: A.... 93: A.... 94: A.... 95: A.... 96: A.... 97: A.... 98: A.... 99: A.... 100: A.... 101: A.... 102: A.... 103: A.... 104: A.... 105: A.... 106: A.... 107: A.... 108: A.... 109: A.... 110: A.... 111: A.... 112: A.... 113: A.... 114: A.... 115: A.... 116: A.... 117: A.... 118: A.... 119: A.... 120: A.... 121: A.... 122: A.... 123: A.... 124: A.... 125: A.... 126: A.... 127: A.... 128: A.... 129: A.... 130: A.... 131: A.... 132: A.... 133: A.... 134: A.... 135: A.... 136: A.... 137: A.... 138: A.... 139: A.... 140: A.... 141: A.... 142: A.... 143: A.... 144: A.... 145: A.... 146: A.... 147: A.... 148: A.... 149: A.... 150: A.... 151: A.... 152: A.... 153: A.... 154: A.... 155: A.... 156: A.... 157: A.... 158: A.... 159: A.... 160: A.... 161: A.... 162: A.... 163: A.... 164: A.... 165: A.... 166: A.... 167: A.... 168: A.... 169: A.... 170: A.... 171: A.... 172: A.... 173: A.... 174: A.... 175: A.... 176: A.... 177: A.... 178: A.... 179: A.... 180: A.... 181: A.... 182: A.... 183: A.... 184: A.... 185: A.... 186: A.... 187: A.... 188: A.... 189: A.... 190: A.... 191: A.... 192: A.... 193: A.... 194: A.... 195: A.... 196: A.... 197: A.... 198: A.... 199: A.... 200: A.... 201: A.... 202: A.... 203: A.... 204: A.... 205: A.... 206: A.... 207: A.... 208: A.... 209: A.... 210: A.... 211: A.... 212: A.... 213: A.... 214: A.... 215: A.... 216: A.... 217: GS... 218: A.... 219: A.... 220: A.... 221: A.... 222: A.... 223: A.... 224: G...V 225: G...V [Domain info] id=0x00000000 priority=100 ven fév 9 17:28:00 CET 2007 running: cat /proc/ipipe/trace cat: /proc/ipipe/trace: est un répertoire ven fév 9 17:28:00 CET 2007 running: cat /proc/ipipe/version 1.7-01 ven fév 9 17:28:00 CET 2007 running: cat /proc/ipipe/Xenomai +----- Handling ([A]ccepted, [G]rabbed, [W]ired, [D]iscarded) |+---- Sticky ||+--- Locked |||+-- Exclusive ||||+- Virtual [IRQ] ||||| 217: GS... 226: W...V [Domain info] id=0x58454e4f priority=topmost ven fév 9 17:28:00 CET 2007 running: generate_loads 1 dd workload started, pids 2686 stored in /var/lock/xeno-test.2542.pids ven fév 9 17:28:00 CET 2007 running: cat /proc/interrupts CPU0 CPU1 0: 90229 0 IO-APIC-edge timer 1: 2 0 IO-APIC-edge i8042 4: 786 0 IO-APIC-edge serial 8: 3 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-fasteoi acpi 12: 4 0 IO-APIC-edge i8042 14: 441 0 IO-APIC-edge ide0 16: 741 0 IO-APIC-fasteoi eth0, eth1 17: 7 0 IO-APIC-fasteoi uhci_hcd:usb2 18: 60 0 IO-APIC-fasteoi uhci_hcd:usb3 20: 13740 0 IO-APIC-fasteoi uhci_hcd:usb1, ehci_hcd:usb4, libata NMI: 0 0 LOC: 88930 88924 ERR: 0 MIS: 0 ven fév 9 17:28:00 CET 2007 running: cat /proc/loadavg 1.06 0.49 0.18 4/106 2692 ven fév 9 17:28:00 CET 2007 running: cat /proc/meminfo MemTotal: 792408 kB MemFree: 404272 kB Buffers: 34356 kB Cached: 295348 kB SwapCached: 0 kB Active: 65672 kB Inactive: 294192 kB SwapTotal: 4192924 kB SwapFree: 4192924 kB Dirty: 208 kB Writeback: 0 kB AnonPages: 30152 kB Mapped: 18408 kB Slab: 15136 kB SReclaimable: 8232 kB SUnreclaim: 6904 kB PageTables: 1356 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 4589128 kB Committed_AS: 86260 kB VmallocTotal: 122580 kB VmallocUsed: 4216 kB VmallocChunk: 114224 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 4096 kB ven fév 9 17:28:00 CET 2007 running: cat /proc/xenomai/apc APC CPU0 CPU1 0: 0 0 (pipe_wakeup) 1: 0 0 (lostage_handler) ven fév 9 17:28:00 CET 2007 running: cat /proc/xenomai/faults TRAP CPU0 CPU1 0: 0 0 (Divide error) 1: 0 0 (Debug) 3: 0 0 (Int3) 4: 0 0 (Overflow) 5: 0 0 (Bounds) 6: 0 0 (Invalid opcode) 7: 0 0 (FPU not available) 8: 0 0 (Double fault) 9: 0 0 (FPU segment overrun) 10: 0 0 (Invalid TSS) 11: 0 0 (Segment not present) 12: 0 0 (Stack segment) 13: 0 0 (General protection) 14: 0 0 (Page fault) 15: 0 0 (Spurious interrupt) 16: 0 0 (FPU error) 17: 0 0 (Alignment check) 18: 0 0 (Machine check) 19: 0 0 (SIMD error) ven fév 9 17:28:00 CET 2007 running: cat /proc/xenomai/hal 1.7-01 ven fév 9 17:28:00 CET 2007 running: cat /proc/xenomai/heap cat: /proc/xenomai/heap: Aucun processus de ce type ven fév 9 17:28:00 CET 2007 running: cat /proc/xenomai/irq IRQ CPU0 CPU1 217: 0 0 226: 0 0 [virtual] ven fév 9 17:28:00 CET 2007 running: cat /proc/xenomai/latency 2699 ven fév 9 17:28:00 CET 2007 running: cat /proc/xenomai/nmi_maxlat 100 ven fév 9 17:28:00 CET 2007 running: cat /proc/xenomai/sched cat: /proc/xenomai/sched: Aucun processus de ce type ven fév 9 17:28:00 CET 2007 running: cat /proc/xenomai/stat cat: /proc/xenomai/stat: Aucun processus de ce type ven fév 9 17:28:00 CET 2007 running: cat /proc/xenomai/timer status=off:setup=55:tickval=0:jiffies=0 ven fév 9 17:28:01 CET 2007 running: cat /proc/xenomai/version 2.3 ven fév 9 17:28:01 CET 2007 running: cat /proc/xenomai/interfaces/core 0 ven fév 9 17:28:01 CET 2007 running: top -bn1c top - 17:28:02 up 1 min, 1 user, load average: 1.06, 0.49, 0.18 Tasks: 99 total, 2 running, 97 sleeping, 0 stopped, 0 zombie Cpu(s): 5.6%us, 14.1%sy, 0.0%ni, 73.0%id, 7.0%wa, 0.0%hi, 0.2%si, 0.0%st Mem: 792408k total, 388444k used, 403964k free, 34372k buffers Swap: 4192924k total, 0k used, 4192924k free, 295452k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2686 root 25 0 3828 548 468 R 77 0.1 0:02.10 dd if /dev/zero of 2735 root 20 0 2164 896 704 R 3 0.1 0:00.05 top -bn1c 1 root 15 0 2032 640 548 S 0 0.1 0:01.50 init [5] ven fév 9 17:28:02 CET 2007 running: ./run -- -sh -T 120 -t0 # latency * * * Type ^C to stop this application. * * Xenomai: SMI-enabled chipset found, enabling SMI workaround. Xenomai: NMI watchdog not available. ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-09 16:49 ` Eric Noulard @ 2007-02-09 17:03 ` Gilles Chanteperdrix 2007-02-09 17:09 ` Jan Kiszka ` (2 more replies) 0 siblings, 3 replies; 19+ messages in thread From: Gilles Chanteperdrix @ 2007-02-09 17:03 UTC (permalink / raw) To: Eric Noulard; +Cc: Xenomai help, Jan Kiszka Eric Noulard wrote: > 2007/2/8, Jan Kiszka <jan.kiszka@domain.hid>: > >>Can you attach a serial console to your system (see >>linux/Documentation/serial-console.txt) and grab the full kernel log up >>to the hang? > > > Here you go. > I recompile a linux 2.6.19 + adeos-ipipe-2.6.19-i386-1.7-01.patch > for xenomai 2.3 in order to avoid to look at may be previous ipipe bugs. > > I did: > 1- attached the serial console > 2- login on serial console as root > 3- launch xeno-test (no args) > > Then the machine freeze.... > > >>Maybe we have an oops that just cannot come out anymore. > > > No oops anywhere :((( Maybe you should enable kernel debugging and xenomai debugging. If I were you, I would reserve the console for error logging, I would not use it to log in. >From your logs, there is one thing you should try first: disable HPET timer, since the box seems to have one and it is used by Linux, and there is no support whatsoever of the HPET timer by Xenomai. -- Gilles Chanteperdrix ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-09 17:03 ` Gilles Chanteperdrix @ 2007-02-09 17:09 ` Jan Kiszka 2007-02-09 17:39 ` Eric Noulard 2007-02-09 17:31 ` Eric Noulard 2007-02-12 8:58 ` Eric Noulard 2 siblings, 1 reply; 19+ messages in thread From: Jan Kiszka @ 2007-02-09 17:09 UTC (permalink / raw) To: Eric Noulard; +Cc: Xenomai help [-- Attachment #1: Type: text/plain, Size: 1267 bytes --] Gilles Chanteperdrix wrote: > Eric Noulard wrote: >> 2007/2/8, Jan Kiszka <jan.kiszka@domain.hid>: >> >>> Can you attach a serial console to your system (see >>> linux/Documentation/serial-console.txt) and grab the full kernel log up >>> to the hang? >> >> Here you go. >> I recompile a linux 2.6.19 + adeos-ipipe-2.6.19-i386-1.7-01.patch >> for xenomai 2.3 in order to avoid to look at may be previous ipipe bugs. >> >> I did: >> 1- attached the serial console >> 2- login on serial console as root >> 3- launch xeno-test (no args) >> >> Then the machine freeze.... >> >> >>> Maybe we have an oops that just cannot come out anymore. >> >> No oops anywhere :((( > > Maybe you should enable kernel debugging and xenomai debugging. If I > were you, I would reserve the console for error logging, I would not use > it to log in. > > From your logs, there is one thing you should try first: disable HPET > timer, since the box seems to have one and it is used by Linux, and > there is no support whatsoever of the HPET timer by Xenomai. > And when playing with the config: Enable the NMI watchdog in Xenomai and pass "nmi_watchdog=2" as kernel parameter. Unless something is totally screwed after the lockup, this should choke. [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 250 bytes --] ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-09 17:09 ` Jan Kiszka @ 2007-02-09 17:39 ` Eric Noulard 0 siblings, 0 replies; 19+ messages in thread From: Eric Noulard @ 2007-02-09 17:39 UTC (permalink / raw) To: Jan Kiszka; +Cc: Xenomai help 2007/2/9, Jan Kiszka <jan.kiszka@domain.hid>: > > And when playing with the config: Enable the NMI watchdog in Xenomai and > pass "nmi_watchdog=2" as kernel parameter. Unless something is totally > screwed after the lockup, this should choke. Ok for that too, regarding NMI my current kernel compile option are: zcat /proc/config.gz | grep DEBUG | egrep -e "NMI" CONFIG_XENO_HW_NMI_DEBUG_LATENCY=y CONFIG_XENO_HW_NMI_DEBUG_LATENCY_MAX=100 >From what I understand from Documentation/nmi_watchdog.txt I already a have NMI Watchdog activated since my kernel is SMP. Moreover: zcat /proc/config.gz | grep APIC CONFIG_X86_GOOD_APIC=y CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y did I miss something? Nevertheless I did not add the kernel boot parameter nmi_watchdog=2 and I will on next test cycle. -- Erk ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-09 17:03 ` Gilles Chanteperdrix 2007-02-09 17:09 ` Jan Kiszka @ 2007-02-09 17:31 ` Eric Noulard 2007-02-09 17:48 ` Gilles Chanteperdrix 2007-02-12 8:58 ` Eric Noulard 2 siblings, 1 reply; 19+ messages in thread From: Eric Noulard @ 2007-02-09 17:31 UTC (permalink / raw) To: Gilles Chanteperdrix; +Cc: Xenomai help, Jan Kiszka 2007/2/9, Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>: > Eric Noulard wrote: > > 2007/2/8, Jan Kiszka <jan.kiszka@domain.hid>: > > > >>Can you attach a serial console to your system (see > >>linux/Documentation/serial-console.txt) and grab the full kernel log up > >>to the hang? > > > > > > Here you go. > > I recompile a linux 2.6.19 + adeos-ipipe-2.6.19-i386-1.7-01.patch > > for xenomai 2.3 in order to avoid to look at may be previous ipipe bugs. > > > > I did: > > 1- attached the serial console > > 2- login on serial console as root > > 3- launch xeno-test (no args) > > > > Then the machine freeze.... > > > > > >>Maybe we have an oops that just cannot come out anymore. > > > > > > No oops anywhere :((( > > Maybe you should enable kernel debugging and xenomai debugging. The tested kernel already have some (if not all) debugging option set zcat /proc/config.gz | grep DEBUG | egrep -e "IPIPE|XENO|KERN" # CONFIG_XENO_OPT_DEBUG is not set CONFIG_XENO_HW_NMI_DEBUG_LATENCY=y CONFIG_XENO_HW_NMI_DEBUG_LATENCY_MAX=100 CONFIG_XENO_OPT_DEBUG_POSIX=y CONFIG_IPIPE_DEBUG=y CONFIG_DEBUG_KERNEL=y You mean I should enable CONFIG_XENO_OPT_DEBUG right? Or just any "debugging thing" I found :)) > If I > were you, I would reserve the console for error logging, I would not use > it to log in. Ok for that, I will do that next time. > > From your logs, there is one thing you should try first: disable HPET > timer, since the box seems to have one and it is used by Linux, and > there is no support whatsoever of the HPET timer by Xenomai. Ok too, will do that soon. -- Erk ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-09 17:31 ` Eric Noulard @ 2007-02-09 17:48 ` Gilles Chanteperdrix 0 siblings, 0 replies; 19+ messages in thread From: Gilles Chanteperdrix @ 2007-02-09 17:48 UTC (permalink / raw) To: Eric Noulard; +Cc: Xenomai help, Jan Kiszka Eric Noulard wrote: > You mean I should enable CONFIG_XENO_OPT_DEBUG right? with XENO_OPT_DEBUG and XENO_OPT_WATCHDOG since you are at it. -- Gilles Chanteperdrix ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-09 17:03 ` Gilles Chanteperdrix 2007-02-09 17:09 ` Jan Kiszka 2007-02-09 17:31 ` Eric Noulard @ 2007-02-12 8:58 ` Eric Noulard 2007-02-12 9:35 ` Jan Kiszka 2 siblings, 1 reply; 19+ messages in thread From: Eric Noulard @ 2007-02-12 8:58 UTC (permalink / raw) To: Gilles Chanteperdrix; +Cc: Xenomai help, Jan Kiszka 2007/2/9, Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>: > Maybe you should enable kernel debugging and xenomai debugging. If I > were you, I would reserve the console for error logging, I would not use > it to log in. > > From your logs, there is one thing you should try first: disable HPET > timer, since the box seems to have one and it is used by Linux, and > there is no support whatsoever of the HPET timer by Xenomai. Bingo, I disable HPET and xeno-test now runs just fine with no hang at all. >>>>>>>>> == Sampling period: 100 us == Test mode: periodic user-mode task == All results in microseconds warming up... RTT| 00:00:01 (periodic user-mode task, 100 us period, priority 99) RTH|-----lat min|-----lat avg|-----lat max|-overrun|----lat best|---lat worst RTD| 3.346| 3.622| 13.130| 0| 3.346| 13.130 RTD| 3.352| 3.626| 12.365| 0| 3.346| 13.130 RTD| 3.352| 3.629| 12.533| 0| 3.346| 13.130 RTD| 3.342| 3.625| 11.598| 0| 3.342| 13.130 >>>>>>>>>> Thanks to all of us for this bug hunt. I've just added CONFIG_HPET and CONFIG_HPET_TIMER to "should be avoided?" kernel option in the Wiki FAQ: http://www.xenomai.org/index.php/FAQs#Installation_and_Setup I don't know much about Kconfig syntax but I think it should be useful to add explicit warnings when HPET_xxx are enabled just as you do with APM, CPU_FREQ etc... I located this in linux/init/Kconfig and would try something like: comment "WARNING! You enabled HPET timer support " depends on HPET || HPET_TIMER comment "option. These options are known to cause troubles with Xenomai." depends on HPET || HPET_TIMER I may try to re-enable MSI in order to see if its OK without HPET but with MSI. Thanks again. -- Erk ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-12 8:58 ` Eric Noulard @ 2007-02-12 9:35 ` Jan Kiszka 2007-02-12 13:01 ` Gilles Chanteperdrix 0 siblings, 1 reply; 19+ messages in thread From: Jan Kiszka @ 2007-02-12 9:35 UTC (permalink / raw) To: Eric Noulard; +Cc: Xenomai help [-- Attachment #1: Type: text/plain, Size: 2276 bytes --] Eric Noulard wrote: > 2007/2/9, Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>: >> Maybe you should enable kernel debugging and xenomai debugging. If I >> were you, I would reserve the console for error logging, I would not use >> it to log in. >> >> From your logs, there is one thing you should try first: disable HPET >> timer, since the box seems to have one and it is used by Linux, and >> there is no support whatsoever of the HPET timer by Xenomai. > > Bingo, > > I disable HPET and xeno-test now runs just fine with no hang at all. > Interesting. >>>>>>>>>> > == Sampling period: 100 us > == Test mode: periodic user-mode task > == All results in microseconds > warming up... > RTT| 00:00:01 (periodic user-mode task, 100 us period, priority 99) > RTH|-----lat min|-----lat avg|-----lat max|-overrun|----lat best|---lat > worst > RTD| 3.346| 3.622| 13.130| 0| 3.346| > 13.130 > RTD| 3.352| 3.626| 12.365| 0| 3.346| > 13.130 > RTD| 3.352| 3.629| 12.533| 0| 3.346| > 13.130 > RTD| 3.342| 3.625| 11.598| 0| 3.342| > 13.130 >>>>>>>>>>> > > Thanks to all of us for this bug hunt. > > I've just added CONFIG_HPET and CONFIG_HPET_TIMER to > "should be avoided?" kernel option in the Wiki FAQ: > http://www.xenomai.org/index.php/FAQs#Installation_and_Setup > > I don't know much about Kconfig syntax but I think it should be > useful to add explicit warnings when HPET_xxx are enabled > just as you do with APM, CPU_FREQ etc... > > I located this in linux/init/Kconfig > and would try something like: > > comment "WARNING! You enabled HPET timer support " > depends on HPET || HPET_TIMER > comment "option. These options are known to cause troubles with Xenomai." > depends on HPET || HPET_TIMER ACK. But can someone explain *why* there is a clash? Is it due to I-pipe injecting tick events *aside* HPET-generated ticks? I think we should address this clash when I-pipe has to be adopted to clock_event/dyntick in 2.6.21. > > I may try to re-enable MSI in order to see if its OK without HPET > but with MSI. > > Thanks again. Jan [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 250 bytes --] ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-12 9:35 ` Jan Kiszka @ 2007-02-12 13:01 ` Gilles Chanteperdrix 0 siblings, 0 replies; 19+ messages in thread From: Gilles Chanteperdrix @ 2007-02-12 13:01 UTC (permalink / raw) To: Jan Kiszka; +Cc: Xenomai help Jan Kiszka wrote: > But can someone explain *why* there is a clash? Is it due to I-pipe > injecting tick events *aside* HPET-generated ticks? I think we should > address this clash when I-pipe has to be adopted to clock_event/dyntick > in 2.6.21. Maybe the rthal code assume that the local APIC is initialized, whereas it is not, when using the HPET ? -- Gilles Chanteperdrix ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-06 21:37 [Xenomai-help] Multiple NIC trouble Eric Noulard 2007-02-06 21:56 ` Gilles Chanteperdrix @ 2007-02-06 21:59 ` Jan Kiszka 2007-02-06 23:39 ` Philippe Gerum 2 siblings, 0 replies; 19+ messages in thread From: Jan Kiszka @ 2007-02-06 21:59 UTC (permalink / raw) To: Eric Noulard; +Cc: Xenomai help [-- Attachment #1: Type: text/plain, Size: 1519 bytes --] Eric Noulard wrote: > I am about to begin to use Xenomai > on a dual-core x86_64 box. > > I installed FC6 i386 (32bits) since the adeos patch for x86_64 > was not there when I did the install, I may go back > to run xenomai on x86_64 since I install both systems (x86_64 and i386) > > Nevertheless I have three 32bits kernels > > 2.6.19-vanilla (pure kernel.org kernel) > 2.6.20-rc1-rtXX (precompiled from Ingo Molnar) > 2.6.19-xenomai (vanilla + adeos-ipipe-2.6.19-i386-1.6-03.patch) > > The box has 3 ethernet interface (2 on-board + 1 on an additionnal NIC) > > eth0 is the additionnal NIC > eth1,eth2 the on-board I/F > > eth1 used for corporate LAN > eth0 "should" be used for private network (only 2 machines for now) > > With this config the machine boots properly with the non-xenomai > kernels with eth1 and eth0 up and running. > > If I boot the xenomai kernel the machine hangs > (even sysrq does not help) as soon as the system tries to ifup eth0. > > If I disable eth0 the xenomai kernel boots until the end. > If I try to ifup eth0 "manually" afterward I got the same "hang". > > I have no log and sysrq does not work !! > > How would you suggest me to investigate that problem? > o check if you have MSI enabled, if yes, try to disable it o try cpus=1 or !SMP o check if ipipe-1.7-00 makes a difference (it shouldn't, the fixed issue in 1.6-03 showed a different bug pattern) o post your .config so that we can have a look Jan [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 250 bytes --] ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [Xenomai-help] Multiple NIC trouble 2007-02-06 21:37 [Xenomai-help] Multiple NIC trouble Eric Noulard 2007-02-06 21:56 ` Gilles Chanteperdrix 2007-02-06 21:59 ` Jan Kiszka @ 2007-02-06 23:39 ` Philippe Gerum 2 siblings, 0 replies; 19+ messages in thread From: Philippe Gerum @ 2007-02-06 23:39 UTC (permalink / raw) To: Eric Noulard; +Cc: Xenomai help On Tue, 2007-02-06 at 22:37 +0100, Eric Noulard wrote: > I am about to begin to use Xenomai > on a dual-core x86_64 box. > > I installed FC6 i386 (32bits) since the adeos patch for x86_64 > was not there when I did the install, I may go back > to run xenomai on x86_64 since I install both systems (x86_64 and i386) > Xenomai x86_64 is not ready for prime time anyway. [...] > How would you suggest me to investigate that problem? > - try disabling Xenomai (CONFIG_XENOMAI) while keeping the interrupt pipeline (CONFIG_IPIPE) enabled; does the kernel boot properly? - What does /proc/interrupts say on a sane configuration (i.e. that boots)? -- Philippe. ^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2007-02-12 13:01 UTC | newest] Thread overview: 19+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2007-02-06 21:37 [Xenomai-help] Multiple NIC trouble Eric Noulard 2007-02-06 21:56 ` Gilles Chanteperdrix 2007-02-07 7:57 ` Eric Noulard 2007-02-07 11:28 ` Jan Kiszka 2007-02-07 11:38 ` Jan Kiszka 2007-02-07 14:03 ` Eric Noulard 2007-02-08 15:11 ` Eric Noulard 2007-02-08 15:32 ` Jan Kiszka 2007-02-09 16:49 ` Eric Noulard 2007-02-09 17:03 ` Gilles Chanteperdrix 2007-02-09 17:09 ` Jan Kiszka 2007-02-09 17:39 ` Eric Noulard 2007-02-09 17:31 ` Eric Noulard 2007-02-09 17:48 ` Gilles Chanteperdrix 2007-02-12 8:58 ` Eric Noulard 2007-02-12 9:35 ` Jan Kiszka 2007-02-12 13:01 ` Gilles Chanteperdrix 2007-02-06 21:59 ` Jan Kiszka 2007-02-06 23:39 ` Philippe Gerum
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.