* Ensoniq SoundScape VIVO90
@ 2007-09-14 8:12 Krzysztof Helt
2007-09-14 14:34 ` Rene Herman
0 siblings, 1 reply; 8+ messages in thread
From: Krzysztof Helt @ 2007-09-14 8:12 UTC (permalink / raw)
To: ALSA devel
Hi,
I acquired Ensoniq VIVO90 card. I tried sscape driver but it does not
work. I quickly looked at the oss driver in the kernel and it works
completely different (uses different pnp resources for codec and mpu).
I want to ask if somebody tested this driver and if so what was the
Ensoniq card model. If it worked only for non-pnp models I would
integrate at least for VIVO cards.
BTW. I found the old post which describes difference between VIVO and
VIVO90. It is below the email.
Regards,
Krzysztof
Hannu Savolainen (ha...@voxware.pp.fi, ha...@4front-tech.com) wrote:
Temat: Re: Ensoniq VIVO vs. VIVO 90
Bill Plenderleith <nospam!plend...@nortel.ca> writes:
>Are VIVO & VIVO 90 different products?
>Can anyone summarize the diffences?
The only difference is that in VIVO90 the wave table
output signal goes through the codec/mixer chip
(AD1845). In the original VIVO it's summed to the
output of AD1845. This difference is'n really
anything important.
Best regards,
Hannu
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: Ensoniq SoundScape VIVO90 2007-09-14 8:12 Ensoniq SoundScape VIVO90 Krzysztof Helt @ 2007-09-14 14:34 ` Rene Herman 2007-09-14 14:42 ` Krzysztof Helt 2007-09-14 15:17 ` Chris Rankin 0 siblings, 2 replies; 8+ messages in thread From: Rene Herman @ 2007-09-14 14:34 UTC (permalink / raw) To: Krzysztof Helt; +Cc: ALSA devel, Chris Rankin [-- Attachment #1: Type: text/plain, Size: 981 bytes --] On 09/14/2007 10:12 AM, Krzysztof Helt wrote: > I acquired Ensoniq VIVO90 card. I tried sscape driver but it does not > work. I quickly looked at the oss driver in the kernel and it works > completely different (uses different pnp resources for codec and mpu). Also looked at that in response to a list question a while ago and posted a very basic driver for the codec part only: http://mailman.alsa-project.org/pipermail/alsa-devel/2007-April/000716.html Also attached again. Haven't looked at it anymore since then. > I want to ask if somebody tested this driver and if so what was the > Ensoniq card model. If it worked only for non-pnp models I would > integrate at least for VIVO cards. It supposedly worked for the original author (Chris Rankin, CCed) with that ENS3081 card that's listed. I suppose you also have the 4081 as both I and Cody did? (I do also have an old non-pnp soundscape lying about, but I haven't gotten around to testing that yet). Rene. [-- Attachment #2: vivo.diff --] [-- Type: text/plain, Size: 5196 bytes --] commit f52cdda56fd648315fcc276d701760e9183939b3 Author: Rene Herman <rene.herman@gmail.com> Date: Tue May 8 20:25:17 2007 +0200 [ALSA] snd-vivo diff --git a/sound/isa/Kconfig b/sound/isa/Kconfig index cf3803c..9567090 100644 --- a/sound/isa/Kconfig +++ b/sound/isa/Kconfig @@ -397,6 +397,18 @@ config SND_SSCAPE To compile this driver as a module, choose M here: the module will be called snd-sscape. +config SND_VIVO + tristate "Ensoniq Soundscape VIVO(90) Driver" + depends on SND + select SND_MPU401_UART + select SND_CS4231_LIB + help + Say Y here to include support for Ensoniq Soundscape VIVO(90) + soundcards. + + To compile this driver as a module, choose M here: the module + will be called snd-vivo. + config SND_WAVEFRONT tristate "Turtle Beach Maui,Tropez,Tropez+ (Wavefront)" depends on SND diff --git a/sound/isa/Makefile b/sound/isa/Makefile index bb317cc..8f246af 100644 --- a/sound/isa/Makefile +++ b/sound/isa/Makefile @@ -12,6 +12,7 @@ snd-es18xx-objs := es18xx.o snd-opl3sa2-objs := opl3sa2.o snd-sgalaxy-objs := sgalaxy.o snd-sscape-objs := sscape.o +snd-vivo-objs := vivo.o # Toplevel Module Dependency obj-$(CONFIG_SND_ADLIB) += snd-adlib.o @@ -23,6 +24,7 @@ obj-$(CONFIG_SND_ES18XX) += snd-es18xx.o obj-$(CONFIG_SND_OPL3SA2) += snd-opl3sa2.o obj-$(CONFIG_SND_SGALAXY) += snd-sgalaxy.o obj-$(CONFIG_SND_SSCAPE) += snd-sscape.o +obj-$(CONFIG_SND_VIVO) += snd-vivo.o obj-$(CONFIG_SND) += ad1816a/ ad1848/ cs423x/ es1688/ gus/ opti9xx/ \ sb/ wavefront/ diff --git a/sound/isa/vivo.c b/sound/isa/vivo.c new file mode 100644 index 0000000..fd2c774 --- /dev/null +++ b/sound/isa/vivo.c @@ -0,0 +1,148 @@ +/* + * Ensoniq Soundscape VIVO(90) Driver + */ + +#include <sound/driver.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pnp.h> +#include <linux/delay.h> +#include <sound/core.h> +#include <sound/initval.h> +#include <sound/mpu401.h> +#include <sound/cs4231.h> + +#define CRD_NAME "Ensoniq Soundscape VIVO(90)" +#define DRV_NAME "VIVO" +#define DEV_NAME "vivo" + +MODULE_DESCRIPTION(CRD_NAME); +MODULE_AUTHOR("Rene Herman"); +MODULE_LICENSE("GPL"); + +static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; +static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; +static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE; + +module_param_array(index, int, NULL, 0444); +MODULE_PARM_DESC(index, "Index value for " CRD_NAME " soundcard"); +module_param_array(id, charp, NULL, 0444); +MODULE_PARM_DESC(id, "ID string for " CRD_NAME " soundcard"); +module_param_array(enable, bool, NULL, 0444); +MODULE_PARM_DESC(enable, "Enable " CRD_NAME " soundcard"); + +static struct pnp_card_device_id snd_vivo_pnpids[] = { + { .id = "ENS4081", .devs = { { "ENS1011" } } }, + { .id = "" } +}; + +MODULE_DEVICE_TABLE(pnp_card, snd_vivo_pnpids); + +static int snd_vivo_error __devinitdata = -ENODEV; + +static int __devinit snd_vivo_probe(struct pnp_card_link *pcard, + const struct pnp_card_device_id *pid) +{ + static int card_num; + + struct pnp_dev *pdev; + struct snd_card *card; + struct snd_cs4231 *chip; + + int num, error; + + if (card_num == SNDRV_CARDS) + return -ENODEV; + + num = card_num++; + if (!enable[num]) + return -ENODEV; + + pdev = pnp_request_card_device(pcard, pid->devs[0].id, NULL); + if (!pdev || pnp_activate_dev(pdev) < 0) + return -ENODEV; + + card = snd_card_new(index[num], id[num], THIS_MODULE, 0); + if (!card) + return -EINVAL; + + snd_card_set_dev(card, &pdev->dev); + + strcpy(card->driver, DRV_NAME); + strcpy(card->shortname, DRV_NAME); + strcpy(card->longname, CRD_NAME); + + error = snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401, + pnp_port_start(pdev, 0), 0, + pnp_irq(pdev, 1), 0, NULL); + if (error < 0) + goto out; + + msleep(500); + + error = snd_cs4231_create(card, pnp_port_start(pdev, 1) + 4, -1, + pnp_irq(pdev, 0), pnp_dma(pdev, 0), + pnp_dma(pdev, 1), CS4231_HW_DETECT, + 0, &chip); + if (error < 0) + goto out; + + error = snd_cs4231_pcm(chip, 0, NULL); + if (error < 0) + goto out; + + error = snd_cs4231_mixer(chip); + if (error < 0) + goto out; + + error = snd_cs4231_timer(chip, 0, NULL); + if (error < 0) + goto out; + + error = snd_card_register(card); + if (error < 0) + goto out; + + pnp_set_card_drvdata(pcard, card); + return (snd_vivo_error = 0); + +out: snd_card_free(card); + return error; +} + +static void __devexit snd_vivo_remove(struct pnp_card_link *pcard) +{ + snd_card_free(pnp_get_card_drvdata(pcard)); + pnp_set_card_drvdata(pcard, NULL); +} + +static struct pnp_card_driver snd_vivo_driver = { + .flags = PNP_DRIVER_RES_DISABLE, + .name = DEV_NAME, + .id_table = snd_vivo_pnpids, + .probe = snd_vivo_probe, + .remove = __devexit_p(snd_vivo_remove) +}; + +static int __init alsa_card_vivo_init(void) +{ + int error; + + error = pnp_register_card_driver(&snd_vivo_driver); + if (error < 0) + goto out; + + error = snd_vivo_error; + if (error < 0) + pnp_unregister_card_driver(&snd_vivo_driver); + +out: return error; +} + +static void __exit alsa_card_vivo_exit(void) +{ + pnp_unregister_card_driver(&snd_vivo_driver); +} + +module_init(alsa_card_vivo_init); +module_exit(alsa_card_vivo_exit); [-- Attachment #3: Type: text/plain, Size: 160 bytes --] _______________________________________________ Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: Ensoniq SoundScape VIVO90 2007-09-14 14:34 ` Rene Herman @ 2007-09-14 14:42 ` Krzysztof Helt 2007-09-14 15:17 ` Chris Rankin 1 sibling, 0 replies; 8+ messages in thread From: Krzysztof Helt @ 2007-09-14 14:42 UTC (permalink / raw) To: Rene Herman; +Cc: ALSA devel, Chris Rankin Thanks for the answer. I found also this: http://contents.driverguide.com/content.php?id=19870&path=ENSONIQ.INF This is an INF file for the Windows driver of the card with ENS3081 id. It is called "SoundScape PnP". It also gives ranges of io ports and irqs possible to use for the driver (search for IOConfig). They are the same as for the VIVO card I have which means they are incorrect in the sscape driver. I would like to hear something from Cris Rankin. Maybe he tested it on the non-PnP card and the PnP part is untested yet. Regards, Krzysztof On 9/14/07, Rene Herman <rene.herman@gmail.com> wrote: > On 09/14/2007 10:12 AM, Krzysztof Helt wrote: > > > I acquired Ensoniq VIVO90 card. I tried sscape driver but it does not > > work. I quickly looked at the oss driver in the kernel and it works > > completely different (uses different pnp resources for codec and mpu). > > Also looked at that in response to a list question a while ago and posted a > very basic driver for the codec part only: > > http://mailman.alsa-project.org/pipermail/alsa-devel/2007-April/000716.html > > Also attached again. Haven't looked at it anymore since then. > > > I want to ask if somebody tested this driver and if so what was the > > Ensoniq card model. If it worked only for non-pnp models I would > > integrate at least for VIVO cards. > > It supposedly worked for the original author (Chris Rankin, CCed) with that > ENS3081 card that's listed. I suppose you also have the 4081 as both I and > Cody did? > > (I do also have an old non-pnp soundscape lying about, but I haven't gotten > around to testing that yet). > > Rene. > > > commit f52cdda56fd648315fcc276d701760e9183939b3 > Author: Rene Herman <rene.herman@gmail.com> > Date: Tue May 8 20:25:17 2007 +0200 > > [ALSA] snd-vivo > > diff --git a/sound/isa/Kconfig b/sound/isa/Kconfig > index cf3803c..9567090 100644 > --- a/sound/isa/Kconfig > +++ b/sound/isa/Kconfig > @@ -397,6 +397,18 @@ config SND_SSCAPE > To compile this driver as a module, choose M here: the module > will be called snd-sscape. > > +config SND_VIVO > + tristate "Ensoniq Soundscape VIVO(90) Driver" > + depends on SND > + select SND_MPU401_UART > + select SND_CS4231_LIB > + help > + Say Y here to include support for Ensoniq Soundscape VIVO(90) > + soundcards. > + > + To compile this driver as a module, choose M here: the module > + will be called snd-vivo. > + > config SND_WAVEFRONT > tristate "Turtle Beach Maui,Tropez,Tropez+ (Wavefront)" > depends on SND > diff --git a/sound/isa/Makefile b/sound/isa/Makefile > index bb317cc..8f246af 100644 > --- a/sound/isa/Makefile > +++ b/sound/isa/Makefile > @@ -12,6 +12,7 @@ snd-es18xx-objs := es18xx.o > snd-opl3sa2-objs := opl3sa2.o > snd-sgalaxy-objs := sgalaxy.o > snd-sscape-objs := sscape.o > +snd-vivo-objs := vivo.o > > # Toplevel Module Dependency > obj-$(CONFIG_SND_ADLIB) += snd-adlib.o > @@ -23,6 +24,7 @@ obj-$(CONFIG_SND_ES18XX) += snd-es18xx.o > obj-$(CONFIG_SND_OPL3SA2) += snd-opl3sa2.o > obj-$(CONFIG_SND_SGALAXY) += snd-sgalaxy.o > obj-$(CONFIG_SND_SSCAPE) += snd-sscape.o > +obj-$(CONFIG_SND_VIVO) += snd-vivo.o > > obj-$(CONFIG_SND) += ad1816a/ ad1848/ cs423x/ es1688/ gus/ opti9xx/ \ > sb/ wavefront/ > diff --git a/sound/isa/vivo.c b/sound/isa/vivo.c > new file mode 100644 > index 0000000..fd2c774 > --- /dev/null > +++ b/sound/isa/vivo.c > @@ -0,0 +1,148 @@ > +/* > + * Ensoniq Soundscape VIVO(90) Driver > + */ > + > +#include <sound/driver.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/pnp.h> > +#include <linux/delay.h> > +#include <sound/core.h> > +#include <sound/initval.h> > +#include <sound/mpu401.h> > +#include <sound/cs4231.h> > + > +#define CRD_NAME "Ensoniq Soundscape VIVO(90)" > +#define DRV_NAME "VIVO" > +#define DEV_NAME "vivo" > + > +MODULE_DESCRIPTION(CRD_NAME); > +MODULE_AUTHOR("Rene Herman"); > +MODULE_LICENSE("GPL"); > + > +static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; > +static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; > +static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE; > + > +module_param_array(index, int, NULL, 0444); > +MODULE_PARM_DESC(index, "Index value for " CRD_NAME " soundcard"); > +module_param_array(id, charp, NULL, 0444); > +MODULE_PARM_DESC(id, "ID string for " CRD_NAME " soundcard"); > +module_param_array(enable, bool, NULL, 0444); > +MODULE_PARM_DESC(enable, "Enable " CRD_NAME " soundcard"); > + > +static struct pnp_card_device_id snd_vivo_pnpids[] = { > + { .id = "ENS4081", .devs = { { "ENS1011" } } }, > + { .id = "" } > +}; > + > +MODULE_DEVICE_TABLE(pnp_card, snd_vivo_pnpids); > + > +static int snd_vivo_error __devinitdata = -ENODEV; > + > +static int __devinit snd_vivo_probe(struct pnp_card_link *pcard, > + const struct pnp_card_device_id *pid) > +{ > + static int card_num; > + > + struct pnp_dev *pdev; > + struct snd_card *card; > + struct snd_cs4231 *chip; > + > + int num, error; > + > + if (card_num == SNDRV_CARDS) > + return -ENODEV; > + > + num = card_num++; > + if (!enable[num]) > + return -ENODEV; > + > + pdev = pnp_request_card_device(pcard, pid->devs[0].id, NULL); > + if (!pdev || pnp_activate_dev(pdev) < 0) > + return -ENODEV; > + > + card = snd_card_new(index[num], id[num], THIS_MODULE, 0); > + if (!card) > + return -EINVAL; > + > + snd_card_set_dev(card, &pdev->dev); > + > + strcpy(card->driver, DRV_NAME); > + strcpy(card->shortname, DRV_NAME); > + strcpy(card->longname, CRD_NAME); > + > + error = snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401, > + pnp_port_start(pdev, 0), 0, > + pnp_irq(pdev, 1), 0, NULL); > + if (error < 0) > + goto out; > + > + msleep(500); > + > + error = snd_cs4231_create(card, pnp_port_start(pdev, 1) + 4, -1, > + pnp_irq(pdev, 0), pnp_dma(pdev, 0), > + pnp_dma(pdev, 1), CS4231_HW_DETECT, > + 0, &chip); > + if (error < 0) > + goto out; > + > + error = snd_cs4231_pcm(chip, 0, NULL); > + if (error < 0) > + goto out; > + > + error = snd_cs4231_mixer(chip); > + if (error < 0) > + goto out; > + > + error = snd_cs4231_timer(chip, 0, NULL); > + if (error < 0) > + goto out; > + > + error = snd_card_register(card); > + if (error < 0) > + goto out; > + > + pnp_set_card_drvdata(pcard, card); > + return (snd_vivo_error = 0); > + > +out: snd_card_free(card); > + return error; > +} > + > +static void __devexit snd_vivo_remove(struct pnp_card_link *pcard) > +{ > + snd_card_free(pnp_get_card_drvdata(pcard)); > + pnp_set_card_drvdata(pcard, NULL); > +} > + > +static struct pnp_card_driver snd_vivo_driver = { > + .flags = PNP_DRIVER_RES_DISABLE, > + .name = DEV_NAME, > + .id_table = snd_vivo_pnpids, > + .probe = snd_vivo_probe, > + .remove = __devexit_p(snd_vivo_remove) > +}; > + > +static int __init alsa_card_vivo_init(void) > +{ > + int error; > + > + error = pnp_register_card_driver(&snd_vivo_driver); > + if (error < 0) > + goto out; > + > + error = snd_vivo_error; > + if (error < 0) > + pnp_unregister_card_driver(&snd_vivo_driver); > + > +out: return error; > +} > + > +static void __exit alsa_card_vivo_exit(void) > +{ > + pnp_unregister_card_driver(&snd_vivo_driver); > +} > + > +module_init(alsa_card_vivo_init); > +module_exit(alsa_card_vivo_exit); > > ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Ensoniq SoundScape VIVO90 2007-09-14 14:34 ` Rene Herman 2007-09-14 14:42 ` Krzysztof Helt @ 2007-09-14 15:17 ` Chris Rankin 2007-09-14 15:51 ` Rene Herman 2007-09-14 16:50 ` Krzysztof Helt 1 sibling, 2 replies; 8+ messages in thread From: Chris Rankin @ 2007-09-14 15:17 UTC (permalink / raw) To: Rene Herman; +Cc: Krzysztof Helt, ALSA devel --- Rene Herman <rene.herman@gmail.com> wrote: > > I want to ask if somebody tested this driver and if so what was the > > Ensoniq card model. If it worked only for non-pnp models I would > > integrate at least for VIVO cards. Hello Rene, I naturally tested this driver with the only Ensoniq SoundScape card that I owned (the PnP version), and yes, it works. All I did was convert as much of the original OSS driver to ALSA as I could verify. Cheers, Chris ______________________________________________________ Yahoo! Mail now has unlimited storage, which means you can have spam control and more space for those important e-mails. http://uk.mail.yahoo.com ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Ensoniq SoundScape VIVO90 2007-09-14 15:17 ` Chris Rankin @ 2007-09-14 15:51 ` Rene Herman 2007-09-14 16:06 ` Chris Rankin 2007-09-14 16:50 ` Krzysztof Helt 1 sibling, 1 reply; 8+ messages in thread From: Rene Herman @ 2007-09-14 15:51 UTC (permalink / raw) To: Chris Rankin; +Cc: Krzysztof Helt, ALSA devel On 09/14/2007 05:17 PM, Chris Rankin wrote: > I naturally tested this driver with the only Ensoniq SoundScape card that > I owned (the PnP version), and yes, it works. All I did was convert as > much of the original OSS driver to ALSA as I could verify. Great, thanks for the answer. The 3081 is a little different resource wise then. It finds the codec at "mpu_port" + 8, whereas the VIVOs (4081) has it as a seperate PnP resource. 3081: Soundscape/MPU port = pnp_port(0), irq = pnp_irq(1) Codec port = + 8, irq = pnp_irq(0) 4081: Soundscape/MPU port = pnp_port(0), irq = pnp_irq(1) Codec port = pnp_port(1), irq = pnp_irq(0) It's possible to switch behaviour on the PnP ID (for example by setting pnp_card_device_id->driver_data in the ID table). Rene. ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Ensoniq SoundScape VIVO90 2007-09-14 15:51 ` Rene Herman @ 2007-09-14 16:06 ` Chris Rankin 2007-09-14 16:21 ` Rene Herman 0 siblings, 1 reply; 8+ messages in thread From: Chris Rankin @ 2007-09-14 16:06 UTC (permalink / raw) To: Rene Herman; +Cc: Krzysztof Helt, ALSA devel --- Rene Herman <rene.herman@gmail.com> wrote: > On 09/14/2007 05:17 PM, Chris Rankin wrote: > > I naturally tested this driver with the only Ensoniq SoundScape card that > > I owned (the PnP version), and yes, it works. All I did was convert as > > much of the original OSS driver to ALSA as I could verify. > > Great, thanks for the answer. The 3081 is a little different resource wise > then. It finds the codec at "mpu_port" + 8, whereas the VIVOs (4081) has it > as a seperate PnP resource. > > 3081: Soundscape/MPU port = pnp_port(0), irq = pnp_irq(1) > Codec port = + 8, irq = pnp_irq(0) > > 4081: Soundscape/MPU port = pnp_port(0), irq = pnp_irq(1) > Codec port = pnp_port(1), irq = pnp_irq(0) > > It's possible to switch behaviour on the PnP ID (for example by setting > pnp_card_device_id->driver_data in the ID table). Do you have the old OSS SoundScape driver code, and did it support the VIVO? I seem to recall that there were several extra code-paths in there for other SoundScape versions. Cheers, Chris _______________________________________________________ Try Yahoo! Mail now with Unlimited Storage and see the difference. http://uk.mail.yahoo.com ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Ensoniq SoundScape VIVO90 2007-09-14 16:06 ` Chris Rankin @ 2007-09-14 16:21 ` Rene Herman 0 siblings, 0 replies; 8+ messages in thread From: Rene Herman @ 2007-09-14 16:21 UTC (permalink / raw) To: Chris Rankin; +Cc: Krzysztof Helt, ALSA devel On 09/14/2007 06:06 PM, Chris Rankin wrote: > Do you have the old OSS SoundScape driver code, and did it support the VIVO? I seem to recall that > there were several extra code-paths in there for other SoundScape versions. The code is still in the tree, yes. Krzysztof is looking into it... Rene. ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Ensoniq SoundScape VIVO90 2007-09-14 15:17 ` Chris Rankin 2007-09-14 15:51 ` Rene Herman @ 2007-09-14 16:50 ` Krzysztof Helt 1 sibling, 0 replies; 8+ messages in thread From: Krzysztof Helt @ 2007-09-14 16:50 UTC (permalink / raw) To: Chris Rankin; +Cc: ALSA devel, Rene Herman On Fri, 14 Sep 2007 16:17:33 +0100 (BST) Chris Rankin <rankincj@yahoo.com> wrote: > > I naturally tested this driver with the only Ensoniq SoundScape card that I owned (the PnP > version), and yes, it works. All I did was convert as much of the original OSS driver to ALSA as I > could verify. > Thank you for the answer. I was fooled by the INF file, the link I posted before. If it worked for you I'll try to add another code patch for the ENS4081 model. Regards, Krzysztof ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2007-09-14 16:42 UTC | newest] Thread overview: 8+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2007-09-14 8:12 Ensoniq SoundScape VIVO90 Krzysztof Helt 2007-09-14 14:34 ` Rene Herman 2007-09-14 14:42 ` Krzysztof Helt 2007-09-14 15:17 ` Chris Rankin 2007-09-14 15:51 ` Rene Herman 2007-09-14 16:06 ` Chris Rankin 2007-09-14 16:21 ` Rene Herman 2007-09-14 16:50 ` Krzysztof Helt
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.