Ensoniq SoundScape VIVO90

Ensoniq SoundScape VIVO90

[Krzysztof Helt]

Hi,

I acquired Ensoniq VIVO90 card. I tried sscape driver but it does not
work. I quickly looked at the oss driver in the kernel and it works
completely different (uses different pnp resources for codec and mpu).

I want to ask if somebody tested this driver and if so what was the
Ensoniq card model. If it worked only for non-pnp models I would
integrate at least for VIVO cards.

BTW. I found the old post which describes difference between VIVO and
VIVO90. It is below the email.

Regards,
Krzysztof

Hannu Savolainen (ha...@voxware.pp.fi, ha...@4front-tech.com) wrote:

Temat: Re: Ensoniq VIVO vs. VIVO 90

Bill Plenderleith <nospam!plend...@nortel.ca> writes:
>Are VIVO & VIVO 90 different products?
>Can anyone summarize the diffences?

The only difference is that in VIVO90 the wave table
output signal goes through the codec/mixer chip
(AD1845). In the original VIVO it's summed to the
output of AD1845. This difference is'n really
anything important.

Best regards,

Hannu

Re: Ensoniq SoundScape VIVO90

[Rene Herman]

[-- Attachment #1: Type: text/plain, Size: 981 bytes --]

On 09/14/2007 10:12 AM, Krzysztof Helt wrote:

> I acquired Ensoniq VIVO90 card. I tried sscape driver but it does not 
> work. I quickly looked at the oss driver in the kernel and it works 
> completely different (uses different pnp resources for codec and mpu).

Also looked at that in response to a list question a while ago and posted a 
very basic driver for the codec part only:

http://mailman.alsa-project.org/pipermail/alsa-devel/2007-April/000716.html

Also attached again. Haven't looked at it anymore since then.

> I want to ask if somebody tested this driver and if so what was the 
> Ensoniq card model. If it worked only for non-pnp models I would 
> integrate at least for VIVO cards.

It supposedly worked for the original author (Chris Rankin, CCed) with that 
ENS3081 card that's listed. I suppose you also have the 4081 as both I and 
Cody did?

(I do also have an old non-pnp soundscape lying about, but I haven't gotten 
around to testing that yet).

Rene.


[-- Attachment #2: vivo.diff --]
[-- Type: text/plain, Size: 5196 bytes --]

commit f52cdda56fd648315fcc276d701760e9183939b3
Author: Rene Herman <rene.herman@gmail.com>
Date:   Tue May 8 20:25:17 2007 +0200

    [ALSA] snd-vivo

diff --git a/sound/isa/Kconfig b/sound/isa/Kconfig
index cf3803c..9567090 100644
--- a/sound/isa/Kconfig
+++ b/sound/isa/Kconfig
@@ -397,6 +397,18 @@ config SND_SSCAPE
 	  To compile this driver as a module, choose M here: the module
 	  will be called snd-sscape.
 
+config SND_VIVO
+	tristate "Ensoniq Soundscape VIVO(90) Driver"
+	depends on SND
+	select SND_MPU401_UART
+	select SND_CS4231_LIB
+	help
+	  Say Y here to include support for Ensoniq Soundscape VIVO(90)
+	  soundcards.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called snd-vivo.
+
 config SND_WAVEFRONT
 	tristate "Turtle Beach Maui,Tropez,Tropez+ (Wavefront)"
 	depends on SND
diff --git a/sound/isa/Makefile b/sound/isa/Makefile
index bb317cc..8f246af 100644
--- a/sound/isa/Makefile
+++ b/sound/isa/Makefile
@@ -12,6 +12,7 @@ snd-es18xx-objs := es18xx.o
 snd-opl3sa2-objs := opl3sa2.o
 snd-sgalaxy-objs := sgalaxy.o
 snd-sscape-objs := sscape.o
+snd-vivo-objs := vivo.o
 
 # Toplevel Module Dependency
 obj-$(CONFIG_SND_ADLIB) += snd-adlib.o
@@ -23,6 +24,7 @@ obj-$(CONFIG_SND_ES18XX) += snd-es18xx.o
 obj-$(CONFIG_SND_OPL3SA2) += snd-opl3sa2.o
 obj-$(CONFIG_SND_SGALAXY) += snd-sgalaxy.o
 obj-$(CONFIG_SND_SSCAPE) += snd-sscape.o
+obj-$(CONFIG_SND_VIVO) += snd-vivo.o
 
 obj-$(CONFIG_SND) += ad1816a/ ad1848/ cs423x/ es1688/ gus/ opti9xx/ \
 		     sb/ wavefront/
diff --git a/sound/isa/vivo.c b/sound/isa/vivo.c
new file mode 100644
index 0000000..fd2c774
--- /dev/null
+++ b/sound/isa/vivo.c
@@ -0,0 +1,148 @@
+/*
+ * Ensoniq Soundscape VIVO(90) Driver
+ */
+
+#include <sound/driver.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pnp.h>
+#include <linux/delay.h>
+#include <sound/core.h>
+#include <sound/initval.h>
+#include <sound/mpu401.h>
+#include <sound/cs4231.h>
+
+#define CRD_NAME "Ensoniq Soundscape VIVO(90)"
+#define DRV_NAME "VIVO"
+#define DEV_NAME "vivo"
+
+MODULE_DESCRIPTION(CRD_NAME);
+MODULE_AUTHOR("Rene Herman");
+MODULE_LICENSE("GPL");
+
+static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX;
+static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR;
+static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE;
+
+module_param_array(index, int, NULL, 0444);
+MODULE_PARM_DESC(index, "Index value for " CRD_NAME " soundcard");
+module_param_array(id, charp, NULL, 0444);
+MODULE_PARM_DESC(id, "ID string for " CRD_NAME " soundcard");
+module_param_array(enable, bool, NULL, 0444);
+MODULE_PARM_DESC(enable, "Enable " CRD_NAME " soundcard");
+
+static struct pnp_card_device_id snd_vivo_pnpids[] = {
+	{ .id = "ENS4081", .devs = { { "ENS1011" } } },
+	{ .id = "" }
+};
+
+MODULE_DEVICE_TABLE(pnp_card, snd_vivo_pnpids);
+
+static int snd_vivo_error __devinitdata = -ENODEV;
+
+static int __devinit snd_vivo_probe(struct pnp_card_link *pcard,
+				    const struct pnp_card_device_id *pid)
+{
+	static int card_num;
+
+	struct pnp_dev	  *pdev;
+	struct snd_card	  *card;
+	struct snd_cs4231 *chip;
+
+	int num, error;
+
+	if (card_num == SNDRV_CARDS)
+		return -ENODEV;
+
+	num = card_num++;
+	if (!enable[num])
+		return -ENODEV;
+
+	pdev = pnp_request_card_device(pcard, pid->devs[0].id, NULL);
+	if (!pdev || pnp_activate_dev(pdev) < 0)
+		return -ENODEV;
+
+	card = snd_card_new(index[num], id[num], THIS_MODULE, 0);
+	if (!card)
+		return -EINVAL;
+
+	snd_card_set_dev(card, &pdev->dev);
+
+	strcpy(card->driver, DRV_NAME);
+	strcpy(card->shortname, DRV_NAME);
+	strcpy(card->longname, CRD_NAME);
+
+	error = snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401,
+				    pnp_port_start(pdev, 0), 0,
+				    pnp_irq(pdev, 1), 0, NULL);
+	if (error < 0)
+		goto out;
+
+	msleep(500);
+
+	error = snd_cs4231_create(card, pnp_port_start(pdev, 1) + 4, -1,
+				  pnp_irq(pdev, 0), pnp_dma(pdev, 0),
+				  pnp_dma(pdev, 1), CS4231_HW_DETECT,
+				  0, &chip);
+	if (error < 0)
+		goto out;
+
+	error = snd_cs4231_pcm(chip, 0, NULL);
+	if (error < 0)
+		goto out;
+
+	error = snd_cs4231_mixer(chip);
+	if (error < 0)
+		goto out;
+
+	error = snd_cs4231_timer(chip, 0, NULL);
+	if (error < 0)
+		goto out;
+
+	error = snd_card_register(card);
+	if (error < 0)
+		goto out;
+
+	pnp_set_card_drvdata(pcard, card);
+	return (snd_vivo_error = 0);
+
+out:	snd_card_free(card);
+	return error;
+}
+
+static void __devexit snd_vivo_remove(struct pnp_card_link *pcard)
+{
+	snd_card_free(pnp_get_card_drvdata(pcard));
+	pnp_set_card_drvdata(pcard, NULL);
+}
+
+static struct pnp_card_driver snd_vivo_driver = {
+	.flags		= PNP_DRIVER_RES_DISABLE,
+	.name		= DEV_NAME,
+	.id_table	= snd_vivo_pnpids,
+	.probe		= snd_vivo_probe,
+	.remove		= __devexit_p(snd_vivo_remove)
+};
+
+static int __init alsa_card_vivo_init(void)
+{
+	int error;
+
+	error = pnp_register_card_driver(&snd_vivo_driver);
+	if (error < 0)
+		goto out;
+
+	error = snd_vivo_error;
+	if (error < 0)
+		pnp_unregister_card_driver(&snd_vivo_driver);
+
+out:	return error;
+}
+
+static void __exit alsa_card_vivo_exit(void)
+{
+	pnp_unregister_card_driver(&snd_vivo_driver);
+}
+
+module_init(alsa_card_vivo_init);
+module_exit(alsa_card_vivo_exit);

[-- Attachment #3: Type: text/plain, Size: 160 bytes --]

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

Re: Ensoniq SoundScape VIVO90

[Krzysztof Helt]

Thanks for the answer.

I found also this:
http://contents.driverguide.com/content.php?id=19870&path=ENSONIQ.INF

This is an INF file for the Windows driver of the card with ENS3081
id. It is called "SoundScape PnP". It also gives ranges of io ports
and irqs possible to use for the driver (search for IOConfig).
They are the same as for the VIVO card I have which means they are
incorrect in the
sscape driver.

I would like to hear something from Cris Rankin. Maybe he tested it on
the non-PnP card
and the PnP part is untested yet.

Regards,
Krzysztof

On 9/14/07, Rene Herman <rene.herman@gmail.com> wrote:
> On 09/14/2007 10:12 AM, Krzysztof Helt wrote:
>
> > I acquired Ensoniq VIVO90 card. I tried sscape driver but it does not
> > work. I quickly looked at the oss driver in the kernel and it works
> > completely different (uses different pnp resources for codec and mpu).
>
> Also looked at that in response to a list question a while ago and posted a
> very basic driver for the codec part only:
>
> http://mailman.alsa-project.org/pipermail/alsa-devel/2007-April/000716.html
>
> Also attached again. Haven't looked at it anymore since then.
>
> > I want to ask if somebody tested this driver and if so what was the
> > Ensoniq card model. If it worked only for non-pnp models I would
> > integrate at least for VIVO cards.
>
> It supposedly worked for the original author (Chris Rankin, CCed) with that
> ENS3081 card that's listed. I suppose you also have the 4081 as both I and
> Cody did?
>
> (I do also have an old non-pnp soundscape lying about, but I haven't gotten
> around to testing that yet).
>
> Rene.
>
>
> commit f52cdda56fd648315fcc276d701760e9183939b3
> Author: Rene Herman <rene.herman@gmail.com>
> Date:   Tue May 8 20:25:17 2007 +0200
>
>     [ALSA] snd-vivo
>
> diff --git a/sound/isa/Kconfig b/sound/isa/Kconfig
> index cf3803c..9567090 100644
> --- a/sound/isa/Kconfig
> +++ b/sound/isa/Kconfig
> @@ -397,6 +397,18 @@ config SND_SSCAPE
>           To compile this driver as a module, choose M here: the module
>           will be called snd-sscape.
>
> +config SND_VIVO
> +       tristate "Ensoniq Soundscape VIVO(90) Driver"
> +       depends on SND
> +       select SND_MPU401_UART
> +       select SND_CS4231_LIB
> +       help
> +         Say Y here to include support for Ensoniq Soundscape VIVO(90)
> +         soundcards.
> +
> +         To compile this driver as a module, choose M here: the module
> +         will be called snd-vivo.
> +
>  config SND_WAVEFRONT
>         tristate "Turtle Beach Maui,Tropez,Tropez+ (Wavefront)"
>         depends on SND
> diff --git a/sound/isa/Makefile b/sound/isa/Makefile
> index bb317cc..8f246af 100644
> --- a/sound/isa/Makefile
> +++ b/sound/isa/Makefile
> @@ -12,6 +12,7 @@ snd-es18xx-objs := es18xx.o
>  snd-opl3sa2-objs := opl3sa2.o
>  snd-sgalaxy-objs := sgalaxy.o
>  snd-sscape-objs := sscape.o
> +snd-vivo-objs := vivo.o
>
>  # Toplevel Module Dependency
>  obj-$(CONFIG_SND_ADLIB) += snd-adlib.o
> @@ -23,6 +24,7 @@ obj-$(CONFIG_SND_ES18XX) += snd-es18xx.o
>  obj-$(CONFIG_SND_OPL3SA2) += snd-opl3sa2.o
>  obj-$(CONFIG_SND_SGALAXY) += snd-sgalaxy.o
>  obj-$(CONFIG_SND_SSCAPE) += snd-sscape.o
> +obj-$(CONFIG_SND_VIVO) += snd-vivo.o
>
>  obj-$(CONFIG_SND) += ad1816a/ ad1848/ cs423x/ es1688/ gus/ opti9xx/ \
>                      sb/ wavefront/
> diff --git a/sound/isa/vivo.c b/sound/isa/vivo.c
> new file mode 100644
> index 0000000..fd2c774
> --- /dev/null
> +++ b/sound/isa/vivo.c
> @@ -0,0 +1,148 @@
> +/*
> + * Ensoniq Soundscape VIVO(90) Driver
> + */
> +
> +#include <sound/driver.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/pnp.h>
> +#include <linux/delay.h>
> +#include <sound/core.h>
> +#include <sound/initval.h>
> +#include <sound/mpu401.h>
> +#include <sound/cs4231.h>
> +
> +#define CRD_NAME "Ensoniq Soundscape VIVO(90)"
> +#define DRV_NAME "VIVO"
> +#define DEV_NAME "vivo"
> +
> +MODULE_DESCRIPTION(CRD_NAME);
> +MODULE_AUTHOR("Rene Herman");
> +MODULE_LICENSE("GPL");
> +
> +static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX;
> +static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR;
> +static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE;
> +
> +module_param_array(index, int, NULL, 0444);
> +MODULE_PARM_DESC(index, "Index value for " CRD_NAME " soundcard");
> +module_param_array(id, charp, NULL, 0444);
> +MODULE_PARM_DESC(id, "ID string for " CRD_NAME " soundcard");
> +module_param_array(enable, bool, NULL, 0444);
> +MODULE_PARM_DESC(enable, "Enable " CRD_NAME " soundcard");
> +
> +static struct pnp_card_device_id snd_vivo_pnpids[] = {
> +       { .id = "ENS4081", .devs = { { "ENS1011" } } },
> +       { .id = "" }
> +};
> +
> +MODULE_DEVICE_TABLE(pnp_card, snd_vivo_pnpids);
> +
> +static int snd_vivo_error __devinitdata = -ENODEV;
> +
> +static int __devinit snd_vivo_probe(struct pnp_card_link *pcard,
> +                                   const struct pnp_card_device_id *pid)
> +{
> +       static int card_num;
> +
> +       struct pnp_dev    *pdev;
> +       struct snd_card   *card;
> +       struct snd_cs4231 *chip;
> +
> +       int num, error;
> +
> +       if (card_num == SNDRV_CARDS)
> +               return -ENODEV;
> +
> +       num = card_num++;
> +       if (!enable[num])
> +               return -ENODEV;
> +
> +       pdev = pnp_request_card_device(pcard, pid->devs[0].id, NULL);
> +       if (!pdev || pnp_activate_dev(pdev) < 0)
> +               return -ENODEV;
> +
> +       card = snd_card_new(index[num], id[num], THIS_MODULE, 0);
> +       if (!card)
> +               return -EINVAL;
> +
> +       snd_card_set_dev(card, &pdev->dev);
> +
> +       strcpy(card->driver, DRV_NAME);
> +       strcpy(card->shortname, DRV_NAME);
> +       strcpy(card->longname, CRD_NAME);
> +
> +       error = snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401,
> +                                   pnp_port_start(pdev, 0), 0,
> +                                   pnp_irq(pdev, 1), 0, NULL);
> +       if (error < 0)
> +               goto out;
> +
> +       msleep(500);
> +
> +       error = snd_cs4231_create(card, pnp_port_start(pdev, 1) + 4, -1,
> +                                 pnp_irq(pdev, 0), pnp_dma(pdev, 0),
> +                                 pnp_dma(pdev, 1), CS4231_HW_DETECT,
> +                                 0, &chip);
> +       if (error < 0)
> +               goto out;
> +
> +       error = snd_cs4231_pcm(chip, 0, NULL);
> +       if (error < 0)
> +               goto out;
> +
> +       error = snd_cs4231_mixer(chip);
> +       if (error < 0)
> +               goto out;
> +
> +       error = snd_cs4231_timer(chip, 0, NULL);
> +       if (error < 0)
> +               goto out;
> +
> +       error = snd_card_register(card);
> +       if (error < 0)
> +               goto out;
> +
> +       pnp_set_card_drvdata(pcard, card);
> +       return (snd_vivo_error = 0);
> +
> +out:   snd_card_free(card);
> +       return error;
> +}
> +
> +static void __devexit snd_vivo_remove(struct pnp_card_link *pcard)
> +{
> +       snd_card_free(pnp_get_card_drvdata(pcard));
> +       pnp_set_card_drvdata(pcard, NULL);
> +}
> +
> +static struct pnp_card_driver snd_vivo_driver = {
> +       .flags          = PNP_DRIVER_RES_DISABLE,
> +       .name           = DEV_NAME,
> +       .id_table       = snd_vivo_pnpids,
> +       .probe          = snd_vivo_probe,
> +       .remove         = __devexit_p(snd_vivo_remove)
> +};
> +
> +static int __init alsa_card_vivo_init(void)
> +{
> +       int error;
> +
> +       error = pnp_register_card_driver(&snd_vivo_driver);
> +       if (error < 0)
> +               goto out;
> +
> +       error = snd_vivo_error;
> +       if (error < 0)
> +               pnp_unregister_card_driver(&snd_vivo_driver);
> +
> +out:   return error;
> +}
> +
> +static void __exit alsa_card_vivo_exit(void)
> +{
> +       pnp_unregister_card_driver(&snd_vivo_driver);
> +}
> +
> +module_init(alsa_card_vivo_init);
> +module_exit(alsa_card_vivo_exit);
>
>

Re: Ensoniq SoundScape VIVO90

[Chris Rankin]

--- Rene Herman <rene.herman@gmail.com> wrote:
> > I want to ask if somebody tested this driver and if so what was the 
> > Ensoniq card model. If it worked only for non-pnp models I would 
> > integrate at least for VIVO cards.

Hello Rene,

I naturally tested this driver with the only Ensoniq SoundScape card that I owned (the PnP
version), and yes, it works. All I did was convert as much of the original OSS driver to ALSA as I
could verify.

Cheers,
Chris



      ______________________________________________________
Yahoo! Mail now has unlimited storage, which means you can have spam control and more space for those important e-mails.
http://uk.mail.yahoo.com

Re: Ensoniq SoundScape VIVO90

[Rene Herman]

On 09/14/2007 05:17 PM, Chris Rankin wrote:

> I naturally tested this driver with the only Ensoniq SoundScape card that
> I owned (the PnP version), and yes, it works. All I did was convert as
> much of the original OSS driver to ALSA as I could verify.

Great, thanks for the answer. The 3081 is a little different resource wise 
then. It finds the codec at "mpu_port" + 8, whereas the VIVOs (4081) has it 
as a seperate PnP resource.

3081:	Soundscape/MPU	port = pnp_port(0),	irq = pnp_irq(1)
	Codec		port = + 8,		irq = pnp_irq(0)

4081:	Soundscape/MPU	port = pnp_port(0),	irq = pnp_irq(1)
	Codec		port = pnp_port(1),	irq = pnp_irq(0)

It's possible to switch behaviour on the PnP ID (for example by setting 
pnp_card_device_id->driver_data in the ID table).

Rene.

Re: Ensoniq SoundScape VIVO90

[Chris Rankin]

--- Rene Herman <rene.herman@gmail.com> wrote:
> On 09/14/2007 05:17 PM, Chris Rankin wrote:
> > I naturally tested this driver with the only Ensoniq SoundScape card that
> > I owned (the PnP version), and yes, it works. All I did was convert as
> > much of the original OSS driver to ALSA as I could verify.
> 
> Great, thanks for the answer. The 3081 is a little different resource wise 
> then. It finds the codec at "mpu_port" + 8, whereas the VIVOs (4081) has it 
> as a seperate PnP resource.
> 
> 3081:	Soundscape/MPU	port = pnp_port(0),	irq = pnp_irq(1)
> 	Codec		port = + 8,		irq = pnp_irq(0)
> 
> 4081:	Soundscape/MPU	port = pnp_port(0),	irq = pnp_irq(1)
> 	Codec		port = pnp_port(1),	irq = pnp_irq(0)
> 
> It's possible to switch behaviour on the PnP ID (for example by setting 
> pnp_card_device_id->driver_data in the ID table).

Do you have the old OSS SoundScape driver code, and did it support the VIVO? I seem to recall that
there were several extra code-paths in there for other SoundScape versions.

Cheers,
Chris



      _______________________________________________________
Try Yahoo! Mail now with Unlimited Storage and see the difference.
http://uk.mail.yahoo.com

Re: Ensoniq SoundScape VIVO90

[Rene Herman]

On 09/14/2007 06:06 PM, Chris Rankin wrote:

> Do you have the old OSS SoundScape driver code, and did it support the VIVO? I seem to recall that
> there were several extra code-paths in there for other SoundScape versions.

The code is still in the tree, yes. Krzysztof is looking into it...

Rene.

Re: Ensoniq SoundScape VIVO90

[Krzysztof Helt]

On Fri, 14 Sep 2007 16:17:33 +0100 (BST)
Chris Rankin <rankincj@yahoo.com> wrote:

> 
> I naturally tested this driver with the only Ensoniq SoundScape card that I owned (the PnP
> version), and yes, it works. All I did was convert as much of the original OSS driver to ALSA as I
> could verify.
> 

Thank you for the answer. I was fooled by the INF file, the link I posted before.

If it worked for you I'll try to add another code patch for the ENS4081 model.

Regards,
Krzysztof