From: Andrew Gallatin <gallatin@myri.com>
To: Eric Dumazet <dada1@cosmosbay.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>,
David Miller <davem@davemloft.net>,
brice@myri.com, sgruszka@redhat.com, netdev@vger.kernel.org
Subject: Re: [PATCH] myr10ge: again fix lro_gen_skb() alignment
Date: Wed, 29 Apr 2009 10:18:39 -0400 [thread overview]
Message-ID: <49F861BF.7060403@myri.com> (raw)
In-Reply-To: <49F85BF1.1020501@cosmosbay.com>
Eric Dumazet wrote:
> Andrew Gallatin a écrit :
>> Andrew Gallatin wrote:
>>> For variety, I grabbed a different "slow" receiver. This is another
>>> 2 CPU machine, but a dual-socket single-core opteron (Tyan S2895)
>>>
>>> processor : 0
>>> vendor_id : AuthenticAMD
>>> cpu family : 15
>>> model : 37
>>> model name : AMD Opteron(tm) Processor 252
>> <...>
>>> The sender was an identical machine running an ancient RHEL4 kernel
>>> (2.6.9-42.ELsmp) and our downloadable (backported) driver.
>>> (http://www.myri.com/ftp/pub/Myri10GE/myri10ge-linux.1.4.4.tgz)
>>> I disabled LRO, on the sender.
>>>
>>> Binding the IRQ to CPU0, and the netserver to CPU1 I see 8.1Gb/s with
>>> LRO and 8.0Gb/s with GRO.
>> With the recent patch to fix idle CPU time accounting from LKML applied,
>> it is again possible to trust netperf's service demand (based on %CPU).
>> So here is raw netperf output for LRO and GRO, bound as above.
>>
>> TCP SENDFILE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
>> hail1-m.sw.myri.com (10.0.130.167) port 0 AF_INET : cpu bind
>> Recv Send Send Utilization Service
>> Demand
>> Socket Socket Message Elapsed Send Recv Send
Recv
>> Size Size Size Time Throughput local remote local
remote
>> bytes bytes bytes secs. 10^6bits/s % S % S us/KB
>> us/KB
>>
>> LRO:
>> 87380 65536 65536 60.00 8279.36 8.10 77.55 0.160
1.535
>> GRO:
>> 87380 65536 65536 60.00 8053.19 7.86 85.47 0.160
1.739
>>
>> The difference is bigger if you disable TCP timestamps (and thus shrink
>> the packets headers down so they require fewer cachelines):
>> LRO:
>> 87380 65536 65536 60.02 7753.55 8.01 74.06 0.169
1.565
>> GRO:
>> 87380 65536 65536 60.02 7535.12 7.27 84.57 0.158
1.839
>>
>>
>> As you can see, even though the raw bandwidth is very close, the
>> service demand makes it clear that GRO is more expensive
>> than LRO. I just wish I understood why.
>>
>
> What are "vmstat 1" ouputs on both tests ? Any difference on say...
context switches ?
Not much difference is apparent from vmstat, except for a
lower load and slightly higher IRQ rate from LRO:
LRO:
procs -----------memory---------- ---swap-- -----io---- --system--
-----cpu------
r b swpd free buff cache si so bi bo in cs us sy
id wa st
1 0 0 676960 19280 209812 0 0 0 0 14817 24 0
73 27 0 0
1 0 0 677084 19280 209812 0 0 0 0 14834 20 0
73 27 0 0
1 0 0 676916 19280 209812 0 0 0 0 14833 16 0
74 26 0 0
GRO:
r b swpd free buff cache si so bi bo in cs us sy
id wa st
1 0 0 678244 18008 209784 0 0 0 24 14288 32 0
84 16 0 0
1 0 0 678268 18008 209788 0 0 0 0 14403 22 0
85 15 0 0
1 0 0 677956 18008 209788 0 0 0 0 14331 20 0
84 16 0 0
The real difference is visible mainly from mpstat on the CPU handing the
interrupts where you see softirq is much higher:
LRO:
07:15:16 CPU %user %nice %sys %iowait %irq %soft %steal
%idle intr/s
07:15:17 0 0.00 0.00 0.00 0.00 0.00 45.00 0.00
55.00 12907.92
07:15:18 0 0.00 0.00 1.00 0.00 2.00 43.00 0.00
54.00 12707.92
07:15:19 0 0.00 0.00 1.00 0.00 0.00 46.00 0.00
53.00 12825.00
GRO
07:11:59 CPU %user %nice %sys %iowait %irq %soft %steal
%idle intr/s
07:12:00 0 0.00 0.00 0.00 0.00 0.99 66.34 0.00
32.67 12242.57
07:12:01 0 0.00 0.00 0.00 0.00 1.01 66.67 0.00
32.32 12220.00
07:12:02 0 0.00 0.00 0.99 0.00 0.99 65.35 0.00
32.67 12336.00
So it is like "something" GRO is doing in the softirq context is more
expensive than what LRO is doing.
Drew
next prev parent reply other threads:[~2009-04-29 14:19 UTC|newest]
Thread overview: 41+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-04-15 8:09 [PATCH] myr10ge: again fix lro_gen_skb() alignment Stanislaw Gruszka
2009-04-15 9:28 ` David Miller
2009-04-15 9:48 ` Brice Goglin
2009-04-15 10:02 ` David Miller
2009-04-15 13:01 ` Andrew Gallatin
2009-04-15 21:04 ` Andrew Gallatin
2009-04-15 23:42 ` David Miller
2009-04-16 8:50 ` Herbert Xu
2009-04-16 9:02 ` David Miller
2009-04-21 19:19 ` Andrew Gallatin
2009-04-22 10:48 ` Herbert Xu
2009-04-22 15:37 ` Andrew Gallatin
2009-04-24 5:45 ` Herbert Xu
2009-04-24 12:45 ` Andrew Gallatin
2009-04-24 12:51 ` Herbert Xu
2009-04-24 17:13 ` Rick Jones
2009-04-24 16:16 ` Andrew Gallatin
2009-04-24 16:30 ` Herbert Xu
2009-04-24 16:31 ` Herbert Xu
2009-04-27 8:05 ` Herbert Xu
2009-04-27 8:07 ` Herbert Xu
2009-04-27 9:32 ` David Miller
2009-04-27 11:01 ` Herbert Xu
2009-04-27 12:45 ` David Miller
2009-04-27 12:45 ` David Miller
2009-04-28 6:12 ` Herbert Xu
2009-04-28 15:00 ` Andrew Gallatin
2009-04-28 15:02 ` David Miller
2009-04-28 15:20 ` Herbert Xu
2009-04-28 15:44 ` Andrew Gallatin
2009-04-28 21:12 ` Andrew Gallatin
2009-04-29 13:42 ` Andrew Gallatin
2009-04-29 13:53 ` Eric Dumazet
2009-04-29 14:18 ` Andrew Gallatin [this message]
2009-04-29 15:26 ` Eric Dumazet
2009-04-29 17:28 ` Andrew Gallatin
2009-04-30 8:10 ` Herbert Xu
2009-04-30 8:14 ` Herbert Xu
2009-04-30 8:17 ` Eric Dumazet
2009-04-30 19:14 ` Andrew Gallatin
2009-04-23 8:00 ` Herbert Xu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=49F861BF.7060403@myri.com \
--to=gallatin@myri.com \
--cc=brice@myri.com \
--cc=dada1@cosmosbay.com \
--cc=davem@davemloft.net \
--cc=herbert@gondor.apana.org.au \
--cc=netdev@vger.kernel.org \
--cc=sgruszka@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.