* [ath9k-devel] SR71C information
@ 2009-07-22 18:41 Clyde McPherson
2009-07-22 18:47 ` Luis R. Rodriguez
0 siblings, 1 reply; 2+ messages in thread
From: Clyde McPherson @ 2009-07-22 18:41 UTC (permalink / raw)
To: ath9k-devel
Here is the information you requested on the Ubiquity SR71C (Cardbus):
lspci:
0d:00.0 Network controller [0280]: Atheros Communications Inc. AR922X
Wireless Network Adapter [168c:0029] (rev 01)
Subsystem: Device [0777:4c05]
Flags: bus master, 66MHz, medium devsel, latency 168, IRQ 20
Memory at 24000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Kernel driver in use: ath9k
Kernel modules: ath9k
Kernel log file during card init:
Jul 20 22:38:26 javalina kernel: [ 156.640166] pci 0000:0d:00.0: reg 10
32bit mmio: [0x000000-0x00ffff]
Jul 20 22:38:26 javalina kernel: [ 156.640280] pci 0000:0d:00.0: PME#
supported from D0 D3hot
Jul 20 22:38:26 javalina kernel: [ 156.640292] pci 0000:0d:00.0: PME#
disabled
Jul 20 22:38:26 javalina kernel: [ 156.819899] ath9k 0000:0d:00.0:
enabling device (0000 -> 0002)
Jul 20 22:38:26 javalina kernel: [ 156.819917] ath9k 0000:0d:00.0: PCI
INT A -> GSI 20 (level, low) -> IRQ 20
Jul 20 22:38:28 javalina kernel: [ 158.384991] ath: EEPROM regdomain: 0x0
Jul 20 22:38:28 javalina kernel: [ 158.384996] ath: EEPROM indicates
default country code should be used
Jul 20 22:38:28 javalina kernel: [ 158.385000] ath: doing EEPROM
country->regdmn map search
Jul 20 22:38:28 javalina kernel: [ 158.385010] ath: country maps to
regdmn code: 0x3a
Jul 20 22:38:28 javalina kernel: [ 158.385015] ath: Country alpha2
being used: US
Jul 20 22:38:28 javalina kernel: [ 158.385019] ath: Regpair used: 0x3a
Jul 20 22:38:28 javalina kernel: [ 158.386393] phy1: Selected rate
control algorithm 'ath9k_rate_control'
Jul 20 22:38:28 javalina kernel: [ 158.389610] cfg80211: Calling CRDA
for country: US
Jul 20 22:38:28 javalina kernel: [ 158.390088] Registered led device:
ath9k-phy1::radio
Jul 20 22:38:28 javalina kernel: [ 158.390212] Registered led device:
ath9k-phy1::assoc
Jul 20 22:38:28 javalina kernel: [ 158.390337] Registered led device:
ath9k-phy1::tx
Jul 20 22:38:28 javalina kernel: [ 158.390455] Registered led device:
ath9k-phy1::rx
Jul 20 22:38:28 javalina kernel: [ 158.390471] phy1: Atheros AR9280
MAC/BB Rev:2 AR5133 RF Rev:d0: mem=0xdffa0000, irq=20
Jul 20 22:38:28 javalina kernel: [ 158.393583] cfg80211: Regulatory
domain changed to country: US
Jul 20 22:38:28 javalina kernel: [ 158.393590] ^I(start_freq - end_freq
@ bandwidth), (max_antenna_gain, max_eirp)
Jul 20 22:38:28 javalina kernel: [ 158.393596] ^I(2402000 KHz - 2472000
KHz @ 40000 KHz), (300 mBi, 2700 mBm)
Jul 20 22:38:28 javalina kernel: [ 158.393602] ^I(5170000 KHz - 5250000
KHz @ 40000 KHz), (300 mBi, 1700 mBm)
Jul 20 22:38:28 javalina kernel: [ 158.393608] ^I(5250000 KHz - 5330000
KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 20 22:38:28 javalina kernel: [ 158.393614] ^I(5490000 KHz - 5710000
KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 20 22:38:28 javalina kernel: [ 158.393619] ^I(5735000 KHz - 5835000
KHz @ 40000 KHz), (300 mBi, 3000 mBm)
Jul 20 22:38:33 javalina kernel: [ 163.301259] ADDRCONF(NETDEV_UP):
wlan1: link is not ready
Kernel log entry reinit and associated:
Jul 20 23:21:28 javalina kernel: [ 2739.124079] pcmcia_socket
pcmcia_socket0: pccard: CardBus card inserted into slot 0
Jul 20 23:21:28 javalina kernel: [ 2739.124162] pci 0000:0d:00.0: reg 10
32bit mmio: [0x000000-0x00ffff]
Jul 20 23:21:28 javalina kernel: [ 2739.124275] pci 0000:0d:00.0: PME#
supported from D0 D3hot
Jul 20 23:21:28 javalina kernel: [ 2739.124287] pci 0000:0d:00.0: PME#
disabled
Jul 20 23:21:28 javalina kernel: [ 2739.124517] ath9k 0000:0d:00.0:
enabling device (0000 -> 0002)
Jul 20 23:21:28 javalina kernel: [ 2739.124535] ath9k 0000:0d:00.0: PCI
INT A -> GSI 20 (level, low) -> IRQ 20
Jul 20 23:21:30 javalina kernel: [ 2740.688524] ath: EEPROM regdomain: 0x0
Jul 20 23:21:30 javalina kernel: [ 2740.688531] ath: EEPROM indicates
default country code should be used
Jul 20 23:21:30 javalina kernel: [ 2740.688536] ath: doing EEPROM
country->regdmn map search
Jul 20 23:21:30 javalina kernel: [ 2740.688543] ath: country maps to
regdmn code: 0x3a
Jul 20 23:21:30 javalina kernel: [ 2740.688549] ath: Country alpha2
being used: US
Jul 20 23:21:30 javalina kernel: [ 2740.688554] ath: Regpair used: 0x3a
Jul 20 23:21:30 javalina kernel: [ 2740.692172] phy3: Selected rate
control algorithm 'ath9k_rate_control'
Jul 20 23:21:30 javalina kernel: [ 2740.697244] Registered led device:
ath9k-phy3::radio
Jul 20 23:21:30 javalina kernel: [ 2740.697306] Registered led device:
ath9k-phy3::assoc
Jul 20 23:21:30 javalina kernel: [ 2740.697350] Registered led device:
ath9k-phy3::tx
Jul 20 23:21:30 javalina kernel: [ 2740.697392] Registered led device:
ath9k-phy3::rx
Jul 20 23:21:30 javalina kernel: [ 2740.697414] phy3: Atheros AR9280
MAC/BB Rev:2 AR5133 RF Rev:d0: mem=0xe0560000, irq=20
Jul 20 23:21:35 javalina kernel: [ 2745.298212] ADDRCONF(NETDEV_UP):
wlan0: link is not ready
Jul 20 23:21:46 javalina kernel: [ 2756.473904] wlan0: deauthenticating
by local choice (reason=3)
Jul 20 23:21:46 javalina kernel: [ 2756.484506] wlan0: direct probe to
AP 00:14:bf:1f:66:14 (try 1)
Jul 20 23:21:46 javalina kernel: [ 2756.486870] wlan0 direct probe responded
Jul 20 23:21:46 javalina kernel: [ 2756.486876] wlan0: authenticate with
AP 00:14:bf:1f:66:14 (try 1)
Jul 20 23:21:46 javalina kernel: [ 2756.488870] wlan0: authenticated
Jul 20 23:21:46 javalina kernel: [ 2756.684082] wlan0: associate with AP
00:14:bf:1f:66:14 (try 1)
Jul 20 23:21:46 javalina kernel: [ 2756.686685] wlan0: RX AssocResp from
00:14:bf:1f:66:14 (capab=0x1 status=0 aid=4)
Jul 20 23:21:46 javalina kernel: [ 2756.686693] wlan0: associated
Jul 20 23:21:46 javalina kernel: [ 2756.686978] ADDRCONF(NETDEV_CHANGE):
wlan0: link becomes ready
Jul 20 23:21:56 javalina kernel: [ 2766.904042] wlan0: no IPv6 routers
present
iwconfig:
iwconfig after association:
wlan0 IEEE 802.11abgn ESSID:"barn_yard"
Mode:Managed Frequency:2.462 GHz Access Point: 00:14:BF:1F:66:14
Bit Rate=11 Mb/s Tx-Power=27 dBmJul 20 23:21:28 javalina
kernel: [ 2739.124079] pcmcia_socket pcmcia_socket0: pccard:
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on
Link Quality=50/70 Signal level=-60 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Thanks
Clyde "Tex" McPherson
^ permalink raw reply [flat|nested] 2+ messages in thread
* [ath9k-devel] SR71C information
2009-07-22 18:41 [ath9k-devel] SR71C information Clyde McPherson
@ 2009-07-22 18:47 ` Luis R. Rodriguez
0 siblings, 0 replies; 2+ messages in thread
From: Luis R. Rodriguez @ 2009-07-22 18:47 UTC (permalink / raw)
To: ath9k-devel
Note: this e-mail is on a public mailing list.
My reply inline below.
On Wed, Jul 22, 2009 at 11:41 AM, Clyde McPherson<ccmcphe@verizon.net> wrote:
> Here is the information you requested on the Ubiquity SR71C (Cardbus):
>
> lspci:
> 0d:00.0 Network controller [0280]: Atheros Communications Inc. AR922X
> Wireless Network Adapter [168c:0029] (rev 01)
> ? Subsystem: Device [0777:4c05]
> ? Flags: bus master, 66MHz, medium devsel, latency 168, IRQ 20
> ? Memory at 24000000 (32-bit, non-prefetchable) [size=64K]
> ? Capabilities: [44] Power Management version 2
> ? Kernel driver in use: ath9k
> ? Kernel modules: ath9k
>
> Kernel log file during card init:
> Jul 20 22:38:26 javalina kernel: [ ?156.640166] pci 0000:0d:00.0: reg 10
> 32bit mmio: [0x000000-0x00ffff]
> Jul 20 22:38:26 javalina kernel: [ ?156.640280] pci 0000:0d:00.0: PME#
> supported from D0 D3hot
> Jul 20 22:38:26 javalina kernel: [ ?156.640292] pci 0000:0d:00.0: PME#
> disabled
> Jul 20 22:38:26 javalina kernel: [ ?156.819899] ath9k 0000:0d:00.0: enabling
> device (0000 -> 0002)
> Jul 20 22:38:26 javalina kernel: [ ?156.819917] ath9k 0000:0d:00.0: PCI INT
> A -> GSI 20 (level, low) -> IRQ 20
> Jul 20 22:38:28 javalina kernel: [ ?158.384991] ath: EEPROM regdomain: 0x0
> Jul 20 22:38:28 javalina kernel: [ ?158.384996] ath: EEPROM indicates
> default country code should be used
> Jul 20 22:38:28 javalina kernel: [ ?158.385000] ath: doing EEPROM
> country->regdmn map search
> Jul 20 22:38:28 javalina kernel: [ ?158.385010] ath: country maps to regdmn
> code: 0x3a
> Jul 20 22:38:28 javalina kernel: [ ?158.385015] ath: Country alpha2 being
> used: US
> Jul 20 22:38:28 javalina kernel: [ ?158.385019] ath: Regpair used: 0x3a
> Jul 20 22:38:28 javalina kernel: [ ?158.386393] phy1: Selected rate control
> algorithm 'ath9k_rate_control'
> Jul 20 22:38:28 javalina kernel: [ ?158.389610] cfg80211: Calling CRDA for
> country: US
> Jul 20 22:38:28 javalina kernel: [ ?158.390088] Registered led device:
> ath9k-phy1::radio
> Jul 20 22:38:28 javalina kernel: [ ?158.390212] Registered led device:
> ath9k-phy1::assoc
> Jul 20 22:38:28 javalina kernel: [ ?158.390337] Registered led device:
> ath9k-phy1::tx
> Jul 20 22:38:28 javalina kernel: [ ?158.390455] Registered led device:
> ath9k-phy1::rx
> Jul 20 22:38:28 javalina kernel: [ ?158.390471] phy1: Atheros AR9280 MAC/BB
> Rev:2 AR5133 RF Rev:d0: mem=0xdffa0000, irq=20
Interesting! Cardbus AR9280 + AR5113 (dual band)!
Thanks I've updated our external products wiki page [1]
[1] http://wireless.kernel.org/en/users/Drivers/ath9k/products/external
Luis
> Jul 20 22:38:28 javalina kernel: [ ?158.393583] cfg80211: Regulatory domain
> changed to country: US
> Jul 20 22:38:28 javalina kernel: [ ?158.393590] ^I(start_freq - end_freq @
> bandwidth), (max_antenna_gain, max_eirp)
> Jul 20 22:38:28 javalina kernel: [ ?158.393596] ^I(2402000 KHz - 2472000 KHz
> @ 40000 KHz), (300 mBi, 2700 mBm)
> Jul 20 22:38:28 javalina kernel: [ ?158.393602] ^I(5170000 KHz - 5250000 KHz
> @ 40000 KHz), (300 mBi, 1700 mBm)
> Jul 20 22:38:28 javalina kernel: [ ?158.393608] ^I(5250000 KHz - 5330000 KHz
> @ 40000 KHz), (300 mBi, 2000 mBm)
> Jul 20 22:38:28 javalina kernel: [ ?158.393614] ^I(5490000 KHz - 5710000 KHz
> @ 40000 KHz), (300 mBi, 2000 mBm)
> Jul 20 22:38:28 javalina kernel: [ ?158.393619] ^I(5735000 KHz - 5835000 KHz
> @ 40000 KHz), (300 mBi, 3000 mBm)
> Jul 20 22:38:33 javalina kernel: [ ?163.301259] ADDRCONF(NETDEV_UP): wlan1:
> link is not ready
>
> Kernel log entry reinit and associated:
> Jul 20 23:21:28 javalina kernel: [ 2739.124079] pcmcia_socket
> pcmcia_socket0: pccard: CardBus card inserted into slot 0
> Jul 20 23:21:28 javalina kernel: [ 2739.124162] pci 0000:0d:00.0: reg 10
> 32bit mmio: [0x000000-0x00ffff]
> Jul 20 23:21:28 javalina kernel: [ 2739.124275] pci 0000:0d:00.0: PME#
> supported from D0 D3hot
> Jul 20 23:21:28 javalina kernel: [ 2739.124287] pci 0000:0d:00.0: PME#
> disabled
> Jul 20 23:21:28 javalina kernel: [ 2739.124517] ath9k 0000:0d:00.0: enabling
> device (0000 -> 0002)
> Jul 20 23:21:28 javalina kernel: [ 2739.124535] ath9k 0000:0d:00.0: PCI INT
> A -> GSI 20 (level, low) -> IRQ 20
> Jul 20 23:21:30 javalina kernel: [ 2740.688524] ath: EEPROM regdomain: 0x0
> Jul 20 23:21:30 javalina kernel: [ 2740.688531] ath: EEPROM indicates
> default country code should be used
> Jul 20 23:21:30 javalina kernel: [ 2740.688536] ath: doing EEPROM
> country->regdmn map search
> Jul 20 23:21:30 javalina kernel: [ 2740.688543] ath: country maps to regdmn
> code: 0x3a
> Jul 20 23:21:30 javalina kernel: [ 2740.688549] ath: Country alpha2 being
> used: US
> Jul 20 23:21:30 javalina kernel: [ 2740.688554] ath: Regpair used: 0x3a
> Jul 20 23:21:30 javalina kernel: [ 2740.692172] phy3: Selected rate control
> algorithm 'ath9k_rate_control'
> Jul 20 23:21:30 javalina kernel: [ 2740.697244] Registered led device:
> ath9k-phy3::radio
> Jul 20 23:21:30 javalina kernel: [ 2740.697306] Registered led device:
> ath9k-phy3::assoc
> Jul 20 23:21:30 javalina kernel: [ 2740.697350] Registered led device:
> ath9k-phy3::tx
> Jul 20 23:21:30 javalina kernel: [ 2740.697392] Registered led device:
> ath9k-phy3::rx
> Jul 20 23:21:30 javalina kernel: [ 2740.697414] phy3: Atheros AR9280 MAC/BB
> Rev:2 AR5133 RF Rev:d0: mem=0xe0560000, irq=20
> Jul 20 23:21:35 javalina kernel: [ 2745.298212] ADDRCONF(NETDEV_UP): wlan0:
> link is not ready
> Jul 20 23:21:46 javalina kernel: [ 2756.473904] wlan0: deauthenticating by
> local choice (reason=3)
> Jul 20 23:21:46 javalina kernel: [ 2756.484506] wlan0: direct probe to AP
> 00:14:bf:1f:66:14 (try 1)
> Jul 20 23:21:46 javalina kernel: [ 2756.486870] wlan0 direct probe responded
> Jul 20 23:21:46 javalina kernel: [ 2756.486876] wlan0: authenticate with AP
> 00:14:bf:1f:66:14 (try 1)
> Jul 20 23:21:46 javalina kernel: [ 2756.488870] wlan0: authenticated
> Jul 20 23:21:46 javalina kernel: [ 2756.684082] wlan0: associate with AP
> 00:14:bf:1f:66:14 (try 1)
> Jul 20 23:21:46 javalina kernel: [ 2756.686685] wlan0: RX AssocResp from
> 00:14:bf:1f:66:14 (capab=0x1 status=0 aid=4)
> Jul 20 23:21:46 javalina kernel: [ 2756.686693] wlan0: associated
> Jul 20 23:21:46 javalina kernel: [ 2756.686978] ADDRCONF(NETDEV_CHANGE):
> wlan0: link becomes ready
> Jul 20 23:21:56 javalina kernel: [ 2766.904042] wlan0: no IPv6 routers
> present
>
>
> iwconfig:
> iwconfig after association:
> wlan0 ? ? IEEE 802.11abgn ?ESSID:"barn_yard" ? ? ? ? Mode:Managed
> ?Frequency:2.462 GHz ?Access Point: 00:14:BF:1F:66:14
> ? ? ? ? Bit Rate=11 Mb/s ? Tx-Power=27 dBmJul 20 23:21:28 javalina kernel: [
> 2739.124079] pcmcia_socket pcmcia_socket0: pccard:
> ? ? ? ? Retry ?long limit:7 ? RTS thr:off ? Fragment thr:off
> ? ? ? ? Encryption key:off
> ? ? ? ? Power Management:on
> ? ? ? ? Link Quality=50/70 ?Signal level=-60 dBm
> ? ? ? ? Rx invalid nwid:0 ?Rx invalid crypt:0 ?Rx invalid frag:0
> ? ? ? ? Tx excessive retries:0 ?Invalid misc:0 ? Missed beacon:0
>
> Thanks
> Clyde "Tex" McPherson
>
>
>
>
>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2009-07-22 18:47 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-07-22 18:41 [ath9k-devel] SR71C information Clyde McPherson
2009-07-22 18:47 ` Luis R. Rodriguez
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.