Panic:: handle_irq_event

All of lore.kernel.org
 help / color / mirror / Atom feed

* Panic:: handle_irq_event_percpu
@ 2011-10-18 18:55 Sander Eikelenboom
  2011-10-19 16:08 ` Konrad Rzeszutek Wilk
  0 siblings, 1 reply; 9+ messages in thread
From: Sander Eikelenboom @ 2011-10-18 18:55 UTC (permalink / raw)
  To: Konrad Rzeszutek Wilk; +Cc: xen-devel@lists.xensource.com

[-- Attachment #1: Type: text/plain, Size: 1040 bytes --]

Hi Konrad,

On my system (AND phenom x6, 8gb mem) running xen 4.1.2-rc3
and a custom kernel based on:

- your linux-next branch
- pulled in your apci/cpufreq branch
- pulled in latest patches from linuses tree

I'm experiencing infrequent panics at boot (say 1 out of 10 or 20 boots), doesn't seem to matter if it's a cold or a warm boot.
It always seem to happen during or shortly after booting. When it doesn't occur then, it can run for at least several days/weeks (haven't seen it panic then).
It doesn't seem to happen at a particular point at or shortly after booting, but it happens before starting any guests

Unfortunately i haven't had serial console enabled at these times, but i have made some photo's.
The first 3 times it locked completely before being able to print a stacktrace, the 4th time it did (although the photo is a bit unsharp).

So all in all, it kind of strange, i hope you can figure something out from the stacktrace, if not, i will see if i can try with serial console attached.

--
Sander

[-- Attachment #2: panic1.jpg --]
[-- Type: image/jpeg, Size: 282843 bytes --]

[-- Attachment #3: panic2.jpg --]
[-- Type: image/jpeg, Size: 158008 bytes --]

[-- Attachment #4: panic3.jpg --]
[-- Type: image/jpeg, Size: 231011 bytes --]

[-- Attachment #5: panic4.jpg --]
[-- Type: image/jpeg, Size: 553916 bytes --]

[-- Attachment #6: Type: text/plain, Size: 138 bytes --]

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: Panic:: handle_irq_event_percpu
  2011-10-18 18:55 Panic:: handle_irq_event_percpu Sander Eikelenboom
@ 2011-10-19 16:08 ` Konrad Rzeszutek Wilk
  2011-10-19 16:38   ` Huang2, Wei
  0 siblings, 1 reply; 9+ messages in thread
From: Konrad Rzeszutek Wilk @ 2011-10-19 16:08 UTC (permalink / raw)
  To: Sander Eikelenboom, wei.huang2; +Cc: xen-devel@lists.xensource.com

On Tue, Oct 18, 2011 at 08:55:19PM +0200, Sander Eikelenboom wrote:
> Hi Konrad,
> 
> On my system (AND phenom x6, 8gb mem) running xen 4.1.2-rc3
> and a custom kernel based on:
> 
> - your linux-next branch
> - pulled in your apci/cpufreq branch
> - pulled in latest patches from linuses tree

Wei,
Are those similar to what you had been seeing?

> 
> I'm experiencing infrequent panics at boot (say 1 out of 10 or 20 boots), doesn't seem to matter if it's a cold or a warm boot.
> It always seem to happen during or shortly after booting. When it doesn't occur then, it can run for at least several days/weeks (haven't seen it panic then).
> It doesn't seem to happen at a particular point at or shortly after booting, but it happens before starting any guests
> 
> Unfortunately i haven't had serial console enabled at these times, but i have made some photo's.
> The first 3 times it locked completely before being able to print a stacktrace, the 4th time it did (although the photo is a bit unsharp).
> 
> 
> So all in all, it kind of strange, i hope you can figure something out from the stacktrace, if not, i will see if i can try with serial console attached.
> 
> --
> Sander





> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* RE: Panic:: handle_irq_event_percpu
  2011-10-19 16:08 ` Konrad Rzeszutek Wilk
@ 2011-10-19 16:38   ` Huang2, Wei
  2011-10-19 17:30     ` Sander Eikelenboom
  0 siblings, 1 reply; 9+ messages in thread
From: Huang2, Wei @ 2011-10-19 16:38 UTC (permalink / raw)
  To: Konrad Rzeszutek Wilk, Sander Eikelenboom; +Cc: xen-devel@lists.xensource.com

It looks similar. 

Hi Sander, could you please test your system with the following options?

1. iommu=amd-iommu-perdev-intremap in xen.gz GRUB entry
2. pci=nosmi in pvops GRUB entry
3. iommu=0 in xen.gz GRUB entry [optional, only if (1) doesn't work for you]

We were seeing an issue which was caused by messed-up interrupt remap table. George Dunlap's perdev interrupt map solved our problem.

Thanks,
-Wei

-----Original Message-----
From: Konrad Rzeszutek Wilk [mailto:konrad.wilk@oracle.com] 
Sent: Wednesday, October 19, 2011 11:08 AM
To: Sander Eikelenboom; Huang2, Wei
Cc: xen-devel@lists.xensource.com
Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu

On Tue, Oct 18, 2011 at 08:55:19PM +0200, Sander Eikelenboom wrote:
> Hi Konrad,
> 
> On my system (AND phenom x6, 8gb mem) running xen 4.1.2-rc3
> and a custom kernel based on:
> 
> - your linux-next branch
> - pulled in your apci/cpufreq branch
> - pulled in latest patches from linuses tree

Wei,
Are those similar to what you had been seeing?

> 
> I'm experiencing infrequent panics at boot (say 1 out of 10 or 20 boots), doesn't seem to matter if it's a cold or a warm boot.
> It always seem to happen during or shortly after booting. When it doesn't occur then, it can run for at least several days/weeks (haven't seen it panic then).
> It doesn't seem to happen at a particular point at or shortly after booting, but it happens before starting any guests
> 
> Unfortunately i haven't had serial console enabled at these times, but i have made some photo's.
> The first 3 times it locked completely before being able to print a stacktrace, the 4th time it did (although the photo is a bit unsharp).
> 
> 
> So all in all, it kind of strange, i hope you can figure something out from the stacktrace, if not, i will see if i can try with serial console attached.
> 
> --
> Sander





> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: Panic:: handle_irq_event_percpu
  2011-10-19 16:38   ` Huang2, Wei
@ 2011-10-19 17:30     ` Sander Eikelenboom
  2011-10-19 18:27       ` Huang2, Wei
  0 siblings, 1 reply; 9+ messages in thread
From: Sander Eikelenboom @ 2011-10-19 17:30 UTC (permalink / raw)
  To: Huang2, Wei; +Cc: xen-devel@lists.xensource.com, Konrad Rzeszutek Wilk

Hello Wei,

Result is that using only "1" or "1" in combination with "2" always result in SATA I/O errors, so that doesn't boot.

Haven't tried rebooting a lot of times without iommu yet.
(the reason i bought the 890fx board in the first place)
Will try that a few times when i have some more time.

--
Sander

Wednesday, October 19, 2011, 6:38:38 PM, you wrote:

> It looks similar. 

> Hi Sander, could you please test your system with the following options?

> 1. iommu=amd-iommu-perdev-intremap in xen.gz GRUB entry
> 2. pci=nosmi in pvops GRUB entry
> 3. iommu=0 in xen.gz GRUB entry [optional, only if (1) doesn't work for you]

> We were seeing an issue which was caused by messed-up interrupt remap table. George Dunlap's perdev interrupt map solved our problem.

> Thanks,
> -Wei

> -----Original Message-----
> From: Konrad Rzeszutek Wilk [mailto:konrad.wilk@oracle.com] 
> Sent: Wednesday, October 19, 2011 11:08 AM
> To: Sander Eikelenboom; Huang2, Wei
> Cc: xen-devel@lists.xensource.com
> Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu

> On Tue, Oct 18, 2011 at 08:55:19PM +0200, Sander Eikelenboom wrote:
>> Hi Konrad,
>> 
>> On my system (AND phenom x6, 8gb mem) running xen 4.1.2-rc3
>> and a custom kernel based on:
>> 
>> - your linux-next branch
>> - pulled in your apci/cpufreq branch
>> - pulled in latest patches from linuses tree

> Wei,
> Are those similar to what you had been seeing?

>> 
>> I'm experiencing infrequent panics at boot (say 1 out of 10 or 20 boots), doesn't seem to matter if it's a cold or a warm boot.
>> It always seem to happen during or shortly after booting. When it doesn't occur then, it can run for at least several days/weeks (haven't seen it panic then).
>> It doesn't seem to happen at a particular point at or shortly after booting, but it happens before starting any guests
>> 
>> Unfortunately i haven't had serial console enabled at these times, but i have made some photo's.
>> The first 3 times it locked completely before being able to print a stacktrace, the 4th time it did (although the photo is a bit unsharp).
>> 
>> 
>> So all in all, it kind of strange, i hope you can figure something out from the stacktrace, if not, i will see if i can try with serial console attached.
>> 
>> --
>> Sander





>> _______________________________________________
>> Xen-devel mailing list
>> Xen-devel@lists.xensource.com
>> http://lists.xensource.com/xen-devel






-- 
Best regards,
 Sander                            mailto:linux@eikelenboom.it

^ permalink raw reply	[flat|nested] 9+ messages in thread

* RE: Panic:: handle_irq_event_percpu
  2011-10-19 17:30     ` Sander Eikelenboom
@ 2011-10-19 18:27       ` Huang2, Wei
  2011-10-22 14:57         ` Sander Eikelenboom
  0 siblings, 1 reply; 9+ messages in thread
From: Huang2, Wei @ 2011-10-19 18:27 UTC (permalink / raw)
  To: Sander Eikelenboom; +Cc: xen-devel@lists.xensource.com, Rzeszutek Wilk, Konrad

[-- Attachment #1: Type: text/plain, Size: 3285 bytes --]

This reminds me of 23768:09595fdf3638, which reverted WeiWang's patch of forcing perdev-intremap as default. Could you try the attached patch on your Xen 4.1 tree and test with patched xen.gz? 

Thanks,
-Wei

-----Original Message-----
From: xen-devel-bounces@lists.xensource.com [mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Sander Eikelenboom
Sent: Wednesday, October 19, 2011 12:30 PM
To: Huang2, Wei
Cc: xen-devel@lists.xensource.com; Konrad Rzeszutek Wilk
Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu

Hello Wei,

Result is that using only "1" or "1" in combination with "2" always result in SATA I/O errors, so that doesn't boot.

Haven't tried rebooting a lot of times without iommu yet.
(the reason i bought the 890fx board in the first place)
Will try that a few times when i have some more time.

--
Sander

Wednesday, October 19, 2011, 6:38:38 PM, you wrote:

> It looks similar. 

> Hi Sander, could you please test your system with the following options?

> 1. iommu=amd-iommu-perdev-intremap in xen.gz GRUB entry
> 2. pci=nosmi in pvops GRUB entry
> 3. iommu=0 in xen.gz GRUB entry [optional, only if (1) doesn't work for you]

> We were seeing an issue which was caused by messed-up interrupt remap table. George Dunlap's perdev interrupt map solved our problem.

> Thanks,
> -Wei

> -----Original Message-----
> From: Konrad Rzeszutek Wilk [mailto:konrad.wilk@oracle.com] 
> Sent: Wednesday, October 19, 2011 11:08 AM
> To: Sander Eikelenboom; Huang2, Wei
> Cc: xen-devel@lists.xensource.com
> Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu

> On Tue, Oct 18, 2011 at 08:55:19PM +0200, Sander Eikelenboom wrote:
>> Hi Konrad,
>> 
>> On my system (AND phenom x6, 8gb mem) running xen 4.1.2-rc3
>> and a custom kernel based on:
>> 
>> - your linux-next branch
>> - pulled in your apci/cpufreq branch
>> - pulled in latest patches from linuses tree

> Wei,
> Are those similar to what you had been seeing?

>> 
>> I'm experiencing infrequent panics at boot (say 1 out of 10 or 20 boots), doesn't seem to matter if it's a cold or a warm boot.
>> It always seem to happen during or shortly after booting. When it doesn't occur then, it can run for at least several days/weeks (haven't seen it panic then).
>> It doesn't seem to happen at a particular point at or shortly after booting, but it happens before starting any guests
>> 
>> Unfortunately i haven't had serial console enabled at these times, but i have made some photo's.
>> The first 3 times it locked completely before being able to print a stacktrace, the 4th time it did (although the photo is a bit unsharp).
>> 
>> 
>> So all in all, it kind of strange, i hope you can figure something out from the stacktrace, if not, i will see if i can try with serial console attached.
>> 
>> --
>> Sander





>> _______________________________________________
>> Xen-devel mailing list
>> Xen-devel@lists.xensource.com
>> http://lists.xensource.com/xen-devel






-- 
Best regards,
 Sander                            mailto:linux@eikelenboom.it


_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel


[-- Attachment #2: interrupt-map-patch.txt --]
[-- Type: text/plain, Size: 10941 bytes --]

diff -r 9f7602e3127c arch/x86/io_apic.c
--- a/arch/x86/io_apic.c	Thu Oct 13 16:25:28 2011 -0500
+++ b/arch/x86/io_apic.c	Fri Oct 14 10:58:44 2011 -0500
@@ -569,6 +569,13 @@
         }
         __get_cpu_var(vector_irq)[vector] = -1;
         cfg->move_cleanup_count--;
+
+        if ( cfg->move_cleanup_count == 0 
+             &&  cfg->used_vectors )
+        {
+            ASSERT(test_bit(vector, cfg->used_vectors));
+            clear_bit(vector, cfg->used_vectors);
+        }
 unlock:
         spin_unlock(&desc->lock);
     }
diff -r 9f7602e3127c arch/x86/irq.c
--- a/arch/x86/irq.c	Thu Oct 13 16:25:28 2011 -0500
+++ b/arch/x86/irq.c	Fri Oct 14 10:58:44 2011 -0500
@@ -24,6 +24,8 @@
 #include <asm/mach-generic/mach_apic.h>
 #include <public/physdev.h>
 
+static void parse_irq_vector_map_param(char *s);
+
 /* opt_noirqbalance: If true, software IRQ balancing/affinity is disabled. */
 bool_t __read_mostly opt_noirqbalance = 0;
 boolean_param("noirqbalance", opt_noirqbalance);
@@ -31,6 +33,12 @@
 unsigned int __read_mostly nr_irqs_gsi = 16;
 unsigned int __read_mostly nr_irqs;
 integer_param("nr_irqs", nr_irqs);
+
+/* This default may be changed by the AMD IOMMU code */
+int __read_mostly opt_irq_vector_map = OPT_IRQ_VECTOR_MAP_DEFAULT;
+custom_param("irq_vector_map", parse_irq_vector_map_param);
+
+vmask_t global_used_vector_map;
 
 u8 __read_mostly *irq_vector;
 struct irq_desc __read_mostly *irq_desc = NULL;
@@ -59,6 +67,26 @@
 /* irq_ratelimit: the max irq rate allowed in every 10ms, set 0 to disable */
 static unsigned int __read_mostly irq_ratelimit_threshold = 10000;
 integer_param("irq_ratelimit", irq_ratelimit_threshold);
+
+static void __init parse_irq_vector_map_param(char *s)
+{
+    char *ss;
+
+    do {
+        ss = strchr(s, ',');
+        if ( ss )
+            *ss = '\0';
+
+        if ( !strcmp(s, "none"))
+            opt_irq_vector_map=OPT_IRQ_VECTOR_MAP_NONE;
+        else if ( !strcmp(s, "global"))
+            opt_irq_vector_map=OPT_IRQ_VECTOR_MAP_GLOBAL;
+        else if ( !strcmp(s, "per-device"))
+            opt_irq_vector_map=OPT_IRQ_VECTOR_MAP_PERDEV;
+
+        s = ss + 1;
+    } while ( ss );
+}
 
 /* Must be called when irq disabled */
 void lock_vector_lock(void)
@@ -94,6 +122,11 @@
         per_cpu(vector_irq, cpu)[vector] = irq;
     cfg->vector = vector;
     cfg->cpu_mask = online_mask;
+    if ( cfg->used_vectors )
+    {
+        ASSERT(!test_bit(vector, cfg->used_vectors));
+        set_bit(vector, cfg->used_vectors);
+    }
     irq_status[irq] = IRQ_USED;
     if (IO_APIC_IRQ(irq))
         irq_vector[irq] = vector;
@@ -158,6 +191,7 @@
     desc->depth   = 1;
     desc->msi_desc = NULL;
     desc->handler = &no_irq_type;
+    desc->chip_data->used_vectors=NULL;
     cpus_setall(desc->affinity);
     spin_unlock_irqrestore(&desc->lock, flags);
 
@@ -190,6 +224,7 @@
 
     if (likely(!cfg->move_in_progress))
         return;
+
     cpus_and(tmp_mask, cfg->old_cpu_mask, cpu_online_map);
     for_each_cpu_mask(cpu, tmp_mask) {
         for (vector = FIRST_DYNAMIC_VECTOR; vector <= LAST_DYNAMIC_VECTOR;
@@ -200,6 +235,12 @@
              break;
         }
      }
+
+    if ( cfg->used_vectors )
+    {
+        ASSERT(test_bit(vector, cfg->used_vectors));
+        clear_bit(vector, cfg->used_vectors);
+    }
 
     cfg->move_in_progress = 0;
 }
@@ -260,6 +301,7 @@
     cfg->vector = IRQ_VECTOR_UNASSIGNED;
     cpus_clear(cfg->cpu_mask);
     cpus_clear(cfg->old_cpu_mask);
+    cfg->used_vectors = NULL;
 }
 
 int init_irq_data(void)
@@ -329,6 +371,41 @@
     end_none
 };
 
+static vmask_t *irq_get_used_vector_mask(int irq)
+{
+    vmask_t *ret = NULL;
+
+    if ( opt_irq_vector_map == OPT_IRQ_VECTOR_MAP_GLOBAL )
+    {
+        struct irq_desc *desc = irq_to_desc(irq);
+
+        ret = &global_used_vector_map;
+
+        if ( desc->chip_data->used_vectors )
+        {
+            printk(XENLOG_INFO "%s: Strange, unassigned irq %d already has used_vectors!\n",
+                   __func__, irq);
+        }
+        else
+        {
+            int vector;
+            
+            vector = irq_to_vector(irq);
+            if ( vector > 0 )
+            {
+                printk(XENLOG_INFO "%s: Strange, irq %d already assigned vector %d!\n",
+                       __func__, irq, vector);
+                
+                ASSERT(!test_bit(vector, ret));
+
+                set_bit(vector, ret);
+            }
+        }
+    }
+
+    return ret;
+}
+
 int __assign_irq_vector(int irq, struct irq_cfg *cfg, const cpumask_t *mask)
 {
     /*
@@ -347,6 +424,7 @@
     int cpu, err;
     unsigned long flags;
     cpumask_t tmp_mask;
+    vmask_t *irq_used_vectors = NULL;
 
     old_vector = irq_to_vector(irq);
     if (old_vector) {
@@ -361,6 +439,17 @@
         return -EAGAIN;
 
     err = -ENOSPC;
+
+    /* This is the only place normal IRQs are ever marked
+     * as "in use".  If they're not in use yet, check to see
+     * if we need to assign a global vector mask. */
+    if ( irq_status[irq] == IRQ_USED )
+    {
+        irq_used_vectors = cfg->used_vectors;
+    }
+    else
+        irq_used_vectors = irq_get_used_vector_mask(irq);
+
     for_each_cpu_mask(cpu, *mask) {
         int new_cpu;
         int vector, offset;
@@ -386,6 +475,10 @@
         if (test_bit(vector, used_vectors))
             goto next;
 
+        if (irq_used_vectors
+            && test_bit(vector, irq_used_vectors) )
+            goto next;
+
         for_each_cpu_mask(new_cpu, tmp_mask)
             if (per_cpu(vector_irq, new_cpu)[vector] != -1)
                 goto next;
@@ -403,8 +496,20 @@
         cpus_copy(cfg->cpu_mask, tmp_mask);
 
         irq_status[irq] = IRQ_USED;
-            if (IO_APIC_IRQ(irq))
-                    irq_vector[irq] = vector;
+        ASSERT((cfg->used_vectors == NULL)
+               || (cfg->used_vectors == irq_used_vectors));
+        cfg->used_vectors = irq_used_vectors;
+
+        if (IO_APIC_IRQ(irq))
+            irq_vector[irq] = vector;
+
+        if ( cfg->used_vectors )
+        {
+            ASSERT(!test_bit(vector, cfg->used_vectors));
+
+            set_bit(vector, cfg->used_vectors);
+        }
+
         err = 0;
         local_irq_restore(flags);
         break;
@@ -1505,7 +1610,7 @@
 
     if ( !IS_PRIV(current->domain) &&
          !(IS_PRIV_FOR(current->domain, d) &&
-          irq_access_permitted(current->domain, pirq)))
+           irq_access_permitted(current->domain, pirq)))
         return -EPERM;
 
     if ( pirq < 0 || pirq >= d->nr_pirqs || irq < 0 || irq >= nr_irqs )
@@ -1553,8 +1658,22 @@
 
         if ( desc->handler != &no_irq_type )
             dprintk(XENLOG_G_ERR, "dom%d: irq %d in use\n",
-              d->domain_id, irq);
+		    d->domain_id, irq);
         desc->handler = &pci_msi_type;
+
+	if ( opt_irq_vector_map == OPT_IRQ_VECTOR_MAP_PERDEV
+             && !desc->chip_data->used_vectors )
+	{
+            desc->chip_data->used_vectors = &pdev->info.used_vectors;
+            if ( desc->chip_data->vector != IRQ_VECTOR_UNASSIGNED )
+            {
+                int vector = desc->chip_data->vector;
+                ASSERT(!test_bit(vector, desc->chip_data->used_vectors));
+
+                set_bit(vector, desc->chip_data->used_vectors);
+            }
+        }
+
         d->arch.pirq_irq[pirq] = irq;
         d->arch.irq_pirq[irq] = pirq;
         setup_msi_irq(pdev, msi_desc, irq);
diff -r 9f7602e3127c drivers/passthrough/amd/pci_amd_iommu.c
--- a/drivers/passthrough/amd/pci_amd_iommu.c	Thu Oct 13 16:25:28 2011 -0500
+++ b/drivers/passthrough/amd/pci_amd_iommu.c	Fri Oct 14 10:58:44 2011 -0500
@@ -24,6 +24,9 @@
 #include <asm/hvm/iommu.h>
 #include <asm/amd-iommu.h>
 #include <asm/hvm/svm/amd-iommu-proto.h>
+
+extern bool_t __read_mostly opt_irq_perdev_vector_map;
+extern bool_t __read_mostly iommu_amd_perdev_vector_map;
 
 extern unsigned short ivrs_bdf_entries;
 extern struct ivrs_mappings *ivrs_mappings;
@@ -166,6 +169,35 @@
         return -ENODEV;
     }
 
+    /*
+     * AMD IOMMUs don't distinguish between vectors destined for
+     * different cpus when doing interrupt remapping.  This means
+     * that interrupts going through the same intremap table
+     * can't share the same vector.
+     *
+     * If irq_vector_map isn't specified, choose a sensible default:
+     * - If we're using per-device interemap tables, per-device
+     *   vector non-sharing maps
+     * - If we're using a global interemap table, global vector
+     *   non-sharing map
+     */
+    if ( opt_irq_vector_map == OPT_IRQ_VECTOR_MAP_DEFAULT )
+    {
+        if ( amd_iommu_perdev_intremap )
+        {
+            printk("AMD-Vi: Enabling per-device vector maps\n");
+            opt_irq_vector_map = OPT_IRQ_VECTOR_MAP_PERDEV;
+        }
+        else
+        {
+            printk("AMD-Vi: Enabling global vector map\n");
+            opt_irq_vector_map = OPT_IRQ_VECTOR_MAP_GLOBAL;
+        }
+    }
+    else
+    {
+        printk("AMD-Vi: Not overriding irq_vector_map setting\n");
+    }
     return scan_pci_devices();
 }
 
diff -r 9f7602e3127c include/asm-x86/irq.h
--- a/include/asm-x86/irq.h	Thu Oct 13 16:25:28 2011 -0500
+++ b/include/asm-x86/irq.h	Fri Oct 14 10:58:44 2011 -0500
@@ -23,11 +23,16 @@
 #define irq_to_desc(irq)    (&irq_desc[irq])
 #define irq_cfg(irq)        (&irq_cfg[irq])
 
+typedef struct {
+    DECLARE_BITMAP(_bits,NR_VECTORS);
+} vmask_t;
+
 struct irq_cfg {
         int  vector;
         cpumask_t cpu_mask;
         cpumask_t old_cpu_mask;
         unsigned move_cleanup_count;
+        vmask_t *used_vectors;
         u8 move_in_progress : 1;
 };
 
@@ -39,6 +44,13 @@
 extern u8 *irq_vector;
 
 extern bool_t opt_noirqbalance;
+
+#define OPT_IRQ_VECTOR_MAP_DEFAULT 0 /* Do the default thing  */
+#define OPT_IRQ_VECTOR_MAP_NONE    1 /* None */ 
+#define OPT_IRQ_VECTOR_MAP_GLOBAL  2 /* One global vector map (no vector sharing) */ 
+#define OPT_IRQ_VECTOR_MAP_PERDEV  3 /* Per-device vetor map (no vector sharing w/in a device) */
+
+extern int opt_irq_vector_map;
 
 /*
  * Per-cpu current frame pointer - the location of the last exception frame on
diff -r 9f7602e3127c include/xen/pci.h
--- a/include/xen/pci.h	Thu Oct 13 16:25:28 2011 -0500
+++ b/include/xen/pci.h	Fri Oct 14 10:58:44 2011 -0500
@@ -11,6 +11,7 @@
 #include <xen/types.h>
 #include <xen/list.h>
 #include <xen/spinlock.h>
+#include <xen/irq.h>
 
 /*
  * The PCI interface treats multi-function devices as independent
@@ -38,6 +39,7 @@
         u8 bus;
         u8 devfn;
     } physfn;
+   vmask_t used_vectors; 
 };
 
 struct pci_dev {

[-- Attachment #3: Type: text/plain, Size: 138 bytes --]

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: Panic:: handle_irq_event_percpu
  2011-10-19 18:27       ` Huang2, Wei
@ 2011-10-22 14:57         ` Sander Eikelenboom
  2011-10-24 21:51           ` Wei Huang
  0 siblings, 1 reply; 9+ messages in thread
From: Sander Eikelenboom @ 2011-10-22 14:57 UTC (permalink / raw)
  To: Huang2, Wei; +Cc: xen-devel@lists.xensource.com, Konrad Rzeszutek Wilk

Hello Wei,

Is this for xen 4.1.2 ?
All hunks of the patch seem to be rejected.

--
Sander


Wednesday, October 19, 2011, 8:27:55 PM, you wrote:

> This reminds me of 23768:09595fdf3638, which reverted WeiWang's patch of forcing perdev-intremap as default. Could you try the attached patch on your Xen 4.1 tree and test with patched xen.gz? 

> Thanks,
> -Wei

> -----Original Message-----
> From: xen-devel-bounces@lists.xensource.com [mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Sander Eikelenboom
> Sent: Wednesday, October 19, 2011 12:30 PM
> To: Huang2, Wei
> Cc: xen-devel@lists.xensource.com; Konrad Rzeszutek Wilk
> Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu

> Hello Wei,

> Result is that using only "1" or "1" in combination with "2" always result in SATA I/O errors, so that doesn't boot.

> Haven't tried rebooting a lot of times without iommu yet.
> (the reason i bought the 890fx board in the first place)
> Will try that a few times when i have some more time.

> --
> Sander

> Wednesday, October 19, 2011, 6:38:38 PM, you wrote:

>> It looks similar. 

>> Hi Sander, could you please test your system with the following options?

>> 1. iommu=amd-iommu-perdev-intremap in xen.gz GRUB entry
>> 2. pci=nosmi in pvops GRUB entry
>> 3. iommu=0 in xen.gz GRUB entry [optional, only if (1) doesn't work for you]

>> We were seeing an issue which was caused by messed-up interrupt remap table. George Dunlap's perdev interrupt map solved our problem.

>> Thanks,
>> -Wei

>> -----Original Message-----
>> From: Konrad Rzeszutek Wilk [mailto:konrad.wilk@oracle.com] 
>> Sent: Wednesday, October 19, 2011 11:08 AM
>> To: Sander Eikelenboom; Huang2, Wei
>> Cc: xen-devel@lists.xensource.com
>> Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu

>> On Tue, Oct 18, 2011 at 08:55:19PM +0200, Sander Eikelenboom wrote:
>>> Hi Konrad,
>>> 
>>> On my system (AND phenom x6, 8gb mem) running xen 4.1.2-rc3
>>> and a custom kernel based on:
>>> 
>>> - your linux-next branch
>>> - pulled in your apci/cpufreq branch
>>> - pulled in latest patches from linuses tree

>> Wei,
>> Are those similar to what you had been seeing?

>>> 
>>> I'm experiencing infrequent panics at boot (say 1 out of 10 or 20 boots), doesn't seem to matter if it's a cold or a warm boot.
>>> It always seem to happen during or shortly after booting. When it doesn't occur then, it can run for at least several days/weeks (haven't seen it panic then).
>>> It doesn't seem to happen at a particular point at or shortly after booting, but it happens before starting any guests
>>> 
>>> Unfortunately i haven't had serial console enabled at these times, but i have made some photo's.
>>> The first 3 times it locked completely before being able to print a stacktrace, the 4th time it did (although the photo is a bit unsharp).
>>> 
>>> 
>>> So all in all, it kind of strange, i hope you can figure something out from the stacktrace, if not, i will see if i can try with serial console attached.
>>> 
>>> --
>>> Sander





>>> _______________________________________________
>>> Xen-devel mailing list
>>> Xen-devel@lists.xensource.com
>>> http://lists.xensource.com/xen-devel









-- 
Best regards,
 Sander                            mailto:linux@eikelenboom.it

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: Panic:: handle_irq_event_percpu
  2011-10-22 14:57         ` Sander Eikelenboom
@ 2011-10-24 21:51           ` Wei Huang
  2011-10-26 14:12             ` Sander Eikelenboom
  0 siblings, 1 reply; 9+ messages in thread
From: Wei Huang @ 2011-10-24 21:51 UTC (permalink / raw)
  To: Sander Eikelenboom; +Cc: xen-devel@lists.xensource.com, Rzeszutek Wilk, Konrad

Yes, it is for xen-4.1-testing tree. I just applied it to the latest tip (23174:d4253bc5418b). There were some hunks; but it worked in general. Could you try it and replace your xen.gz file with the new version?

(Stripping trailing CRs from patch.)
patching file arch/x86/io_apic.c
Hunk #1 succeeded at 548 (offset -21 lines).
(Stripping trailing CRs from patch.)
patching file arch/x86/irq.c
Hunk #5 succeeded at 192 (offset 1 line).
Hunk #6 succeeded at 225 (offset 1 line).
Hunk #7 succeeded at 236 (offset 1 line).
Hunk #8 succeeded at 302 (offset 1 line).
Hunk #9 succeeded at 372 (offset 1 line).
Hunk #10 succeeded at 425 (offset 1 line).
Hunk #11 succeeded at 440 (offset 1 line).
Hunk #12 succeeded at 476 (offset 1 line).
Hunk #13 succeeded at 497 (offset 1 line).
Hunk #14 succeeded at 1599 (offset -11 lines).
Hunk #15 succeeded at 1647 (offset -11 lines).
(Stripping trailing CRs from patch.)
patching file drivers/passthrough/amd/pci_amd_iommu.c
(Stripping trailing CRs from patch.)
patching file include/asm-x86/irq.h
(Stripping trailing CRs from patch.)
patching file include/xen/pci.h



-Wei
On 10/22/2011 09:57 AM, Sander Eikelenboom wrote:
> Hello Wei,
>
> Is this for xen 4.1.2 ?
> All hunks of the patch seem to be rejected.
>
> --
> Sander
>
>
> Wednesday, October 19, 2011, 8:27:55 PM, you wrote:
>
>> This reminds me of 23768:09595fdf3638, which reverted WeiWang's patch of forcing perdev-intremap as default. Could you try the attached patch on your Xen 4.1 tree and test with patched xen.gz?
>
>> Thanks,
>> -Wei
>
>> -----Original Message-----
>> From: xen-devel-bounces@lists.xensource.com [mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Sander Eikelenboom
>> Sent: Wednesday, October 19, 2011 12:30 PM
>> To: Huang2, Wei
>> Cc: xen-devel@lists.xensource.com; Konrad Rzeszutek Wilk
>> Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu
>
>> Hello Wei,
>
>> Result is that using only "1" or "1" in combination with "2" always result in SATA I/O errors, so that doesn't boot.
>
>> Haven't tried rebooting a lot of times without iommu yet.
>> (the reason i bought the 890fx board in the first place)
>> Will try that a few times when i have some more time.
>
>> --
>> Sander
>
>> Wednesday, October 19, 2011, 6:38:38 PM, you wrote:
>
>>> It looks similar.
>
>>> Hi Sander, could you please test your system with the following options?
>
>>> 1. iommu=amd-iommu-perdev-intremap in xen.gz GRUB entry
>>> 2. pci=nosmi in pvops GRUB entry
>>> 3. iommu=0 in xen.gz GRUB entry [optional, only if (1) doesn't work for you]
>
>>> We were seeing an issue which was caused by messed-up interrupt remap table. George Dunlap's perdev interrupt map solved our problem.
>
>>> Thanks,
>>> -Wei
>
>>> -----Original Message-----
>>> From: Konrad Rzeszutek Wilk [mailto:konrad.wilk@oracle.com]
>>> Sent: Wednesday, October 19, 2011 11:08 AM
>>> To: Sander Eikelenboom; Huang2, Wei
>>> Cc: xen-devel@lists.xensource.com
>>> Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu
>
>>> On Tue, Oct 18, 2011 at 08:55:19PM +0200, Sander Eikelenboom wrote:
>>>> Hi Konrad,
>>>>
>>>> On my system (AND phenom x6, 8gb mem) running xen 4.1.2-rc3
>>>> and a custom kernel based on:
>>>>
>>>> - your linux-next branch
>>>> - pulled in your apci/cpufreq branch
>>>> - pulled in latest patches from linuses tree
>
>>> Wei,
>>> Are those similar to what you had been seeing?
>
>>>>
>>>> I'm experiencing infrequent panics at boot (say 1 out of 10 or 20 boots), doesn't seem to matter if it's a cold or a warm boot.
>>>> It always seem to happen during or shortly after booting. When it doesn't occur then, it can run for at least several days/weeks (haven't seen it panic then).
>>>> It doesn't seem to happen at a particular point at or shortly after booting, but it happens before starting any guests
>>>>
>>>> Unfortunately i haven't had serial console enabled at these times, but i have made some photo's.
>>>> The first 3 times it locked completely before being able to print a stacktrace, the 4th time it did (although the photo is a bit unsharp).
>>>>
>>>>
>>>> So all in all, it kind of strange, i hope you can figure something out from the stacktrace, if not, i will see if i can try with serial console attached.
>>>>
>>>> --
>>>> Sander
>
>
>
>
>
>>>> _______________________________________________
>>>> Xen-devel mailing list
>>>> Xen-devel@lists.xensource.com
>>>> http://lists.xensource.com/xen-devel
>
>
>
>
>
>
>
>
>

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: Panic:: handle_irq_event_percpu
  2011-10-24 21:51           ` Wei Huang
@ 2011-10-26 14:12             ` Sander Eikelenboom
  2011-10-26 14:21               ` Wei Huang
  0 siblings, 1 reply; 9+ messages in thread
From: Sander Eikelenboom @ 2011-10-26 14:12 UTC (permalink / raw)
  To: Wei Huang; +Cc: xen-devel@lists.xensource.com, Konrad Rzeszutek Wilk

[-- Attachment #1: Type: text/plain, Size: 5906 bytes --]

Hello Wei,

Sorry you were right, i'm a bit accustomed that patches apply to the root of the project, this one was for /xen specifically.
I have done a lot of reboots with the patch applied on:
- xen 4.1.3-rc1-pre
- dom0 kernel from Konrad's linux-next tree + devel/acpi-cpufreq.v3 branch + patch from liang tang + linus 3.1 tree pulled in.
- iommu specific boot options used for xen in grub: iommu=on,amd-iommu-debug amd_iommu=on amd-iommu-debug

I haven't seen kernel panics on boot so far, is this output that was expected (from serial console):

<snip>
(XEN) AMD-Vi: Add device table entry: device id = 0x0a07, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0b00, interupt table = 0x24e004000
(XEN) AMD-Vi: IOMMU 0 Enabled.
(XEN) AMD-Vi: Enabling global vector map
(XEN) I/O virtualisation enabled
(XEN)  - Dom0 mode: Relaxed
(XEN) Getting VERSION: 80050010
<snip>

Complete serial console output is attached


Is this patch a candidate for 4.1.3 ?

--

Sander



Monday, October 24, 2011, 11:51:39 PM, you wrote:

> Yes, it is for xen-4.1-testing tree. I just applied it to the latest tip (23174:d4253bc5418b). There were some hunks; but it worked in general. Could you try it and replace your xen.gz file with the new version?

> (Stripping trailing CRs from patch.)
> patching file arch/x86/io_apic.c
> Hunk #1 succeeded at 548 (offset -21 lines).
> (Stripping trailing CRs from patch.)
> patching file arch/x86/irq.c
> Hunk #5 succeeded at 192 (offset 1 line).
> Hunk #6 succeeded at 225 (offset 1 line).
> Hunk #7 succeeded at 236 (offset 1 line).
> Hunk #8 succeeded at 302 (offset 1 line).
> Hunk #9 succeeded at 372 (offset 1 line).
> Hunk #10 succeeded at 425 (offset 1 line).
> Hunk #11 succeeded at 440 (offset 1 line).
> Hunk #12 succeeded at 476 (offset 1 line).
> Hunk #13 succeeded at 497 (offset 1 line).
> Hunk #14 succeeded at 1599 (offset -11 lines).
> Hunk #15 succeeded at 1647 (offset -11 lines).
> (Stripping trailing CRs from patch.)
> patching file drivers/passthrough/amd/pci_amd_iommu.c
> (Stripping trailing CRs from patch.)
> patching file include/asm-x86/irq.h
> (Stripping trailing CRs from patch.)
> patching file include/xen/pci.h



> -Wei
> On 10/22/2011 09:57 AM, Sander Eikelenboom wrote:
>> Hello Wei,
>>
>> Is this for xen 4.1.2 ?
>> All hunks of the patch seem to be rejected.
>>
>> --
>> Sander
>>
>>
>> Wednesday, October 19, 2011, 8:27:55 PM, you wrote:
>>
>>> This reminds me of 23768:09595fdf3638, which reverted WeiWang's patch of forcing perdev-intremap as default. Could you try the attached patch on your Xen 4.1 tree and test with patched xen.gz?
>>
>>> Thanks,
>>> -Wei
>>
>>> -----Original Message-----
>>> From: xen-devel-bounces@lists.xensource.com [mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Sander Eikelenboom
>>> Sent: Wednesday, October 19, 2011 12:30 PM
>>> To: Huang2, Wei
>>> Cc: xen-devel@lists.xensource.com; Konrad Rzeszutek Wilk
>>> Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu
>>
>>> Hello Wei,
>>
>>> Result is that using only "1" or "1" in combination with "2" always result in SATA I/O errors, so that doesn't boot.
>>
>>> Haven't tried rebooting a lot of times without iommu yet.
>>> (the reason i bought the 890fx board in the first place)
>>> Will try that a few times when i have some more time.
>>
>>> --
>>> Sander
>>
>>> Wednesday, October 19, 2011, 6:38:38 PM, you wrote:
>>
>>>> It looks similar.
>>
>>>> Hi Sander, could you please test your system with the following options?
>>
>>>> 1. iommu=amd-iommu-perdev-intremap in xen.gz GRUB entry
>>>> 2. pci=nosmi in pvops GRUB entry
>>>> 3. iommu=0 in xen.gz GRUB entry [optional, only if (1) doesn't work for you]
>>
>>>> We were seeing an issue which was caused by messed-up interrupt remap table. George Dunlap's perdev interrupt map solved our problem.
>>
>>>> Thanks,
>>>> -Wei
>>
>>>> -----Original Message-----
>>>> From: Konrad Rzeszutek Wilk [mailto:konrad.wilk@oracle.com]
>>>> Sent: Wednesday, October 19, 2011 11:08 AM
>>>> To: Sander Eikelenboom; Huang2, Wei
>>>> Cc: xen-devel@lists.xensource.com
>>>> Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu
>>
>>>> On Tue, Oct 18, 2011 at 08:55:19PM +0200, Sander Eikelenboom wrote:
>>>>> Hi Konrad,
>>>>>
>>>>> On my system (AND phenom x6, 8gb mem) running xen 4.1.2-rc3
>>>>> and a custom kernel based on:
>>>>>
>>>>> - your linux-next branch
>>>>> - pulled in your apci/cpufreq branch
>>>>> - pulled in latest patches from linuses tree
>>
>>>> Wei,
>>>> Are those similar to what you had been seeing?
>>
>>>>>
>>>>> I'm experiencing infrequent panics at boot (say 1 out of 10 or 20 boots), doesn't seem to matter if it's a cold or a warm boot.
>>>>> It always seem to happen during or shortly after booting. When it doesn't occur then, it can run for at least several days/weeks (haven't seen it panic then).
>>>>> It doesn't seem to happen at a particular point at or shortly after booting, but it happens before starting any guests
>>>>>
>>>>> Unfortunately i haven't had serial console enabled at these times, but i have made some photo's.
>>>>> The first 3 times it locked completely before being able to print a stacktrace, the 4th time it did (although the photo is a bit unsharp).
>>>>>
>>>>>
>>>>> So all in all, it kind of strange, i hope you can figure something out from the stacktrace, if not, i will see if i can try with serial console attached.
>>>>>
>>>>> --
>>>>> Sander
>>
>>
>>
>>
>>
>>>>> _______________________________________________
>>>>> Xen-devel mailing list
>>>>> Xen-devel@lists.xensource.com
>>>>> http://lists.xensource.com/xen-devel
>>
>>
>>
>>
>>
>>
>>
>>
>>





-- 
Best regards,
 Sander                            mailto:linux@eikelenboom.it

[-- Attachment #2: serialconsole.txt --]
[-- Type: text/plain, Size: 154119 bytes --]

 __  __            _  _    _   _____             _                   
 \ \/ /___ _ __   | || |  / | |___ /    _ __ ___/ |   _ __  _ __ ___ 
  \  // _ \ '_ \  | || |_ | |   |_ \ __| '__/ __| |__| '_ \| '__/ _ \
  /  \  __/ | | | |__   _|| |_ ___) |__| | | (__| |__| |_) | | |  __/
 /_/\_\___|_| |_|    |_|(_)_(_)____/   |_|  \___|_|  | .__/|_|  \___|
                                                     |_|             
(XEN) Xen version 4.1.3-rc1-pre (root@dyndns.org) (gcc version 4.4.5 (Debian 4.4.5-8) ) Tue Oct 25 19:07:44 CEST 2011
(XEN) Latest ChangeSet: Mon Oct 24 18:03:35 2011 +0100 23176:81e39a4978ea
(XEN) Bootloader: GRUB 1.98+20100804-14+squeeze1
(XEN) Command line: dom0_mem=1024M loglvl=all loglvl_guest=all console_timestamps vga=gfx-1280x1024x32 cpuidle cpufreq=xen noreboot debug lapic=debug apic_verbosity=debug apic=debug acpi_enforce_resources=lax iommu=on,amd-iommu-debug amd_iommu=on amd-iommu-debug com1=115200,8n1 console=vga,com1
(XEN) Video information:
(XEN)  VGA is graphics mode 1280x1024, 32 bpp
(XEN)  VBE/DDC methods: V2; EDID transfer time: 1 seconds
(XEN) Disc information:
(XEN)  Found 2 MBR signatures
(XEN)  Found 2 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN)  0000000000000000 - 000000000009f000 (usable)
(XEN)  000000000009f000 - 00000000000a0000 (reserved)
(XEN)  00000000000e4000 - 0000000000100000 (reserved)
(XEN)  0000000000100000 - 00000000aff90000 (usable)
(XEN)  00000000aff90000 - 00000000aff9e000 (ACPI data)
(XEN)  00000000aff9e000 - 00000000affe0000 (ACPI NVS)
(XEN)  00000000affe0000 - 00000000b0000000 (reserved)
(XEN)  00000000ffe00000 - 0000000100000000 (reserved)
(XEN)  0000000100000000 - 0000000250000000 (usable)
(XEN) ACPI: RSDP 000FB120, 0014 (r0 ACPIAM)
(XEN) ACPI: RSDT AFF90000, 0048 (r1 MSI    OEMSLIC  20100622 MSFT       97)
(XEN) ACPI: FACP AFF90200, 0084 (r1 7640MS A7640100 20100622 MSFT       97)
(XEN) ACPI: DSDT AFF905E0, 9449 (r1  A7640 A7640100      100 INTL 20051117)
(XEN) ACPI: FACS AFF9E000, 0040
(XEN) ACPI: APIC AFF90390, 0088 (r1 7640MS A7640100 20100622 MSFT       97)
(XEN) ACPI: MCFG AFF90420, 003C (r1 7640MS OEMMCFG  20100622 MSFT       97)
(XEN) ACPI: SLIC AFF90460, 0176 (r1 MSI    OEMSLIC  20100622 MSFT       97)
(XEN) ACPI: OEMB AFF9E040, 0072 (r1 7640MS A7640100 20100622 MSFT       97)
(XEN) ACPI: SRAT AFF9A5E0, 0108 (r3 AMD    FAM_F_10        2 AMD         1)
(XEN) ACPI: HPET AFF9A6F0, 0038 (r1 7640MS OEMHPET  20100622 MSFT       97)
(XEN) ACPI: IVRS AFF9A730, 0100 (r1  AMD     RD890S   202031 AMD         0)
(XEN) ACPI: SSDT AFF9A830, 0DA4 (r1 A M I  POWERNOW        1 AMD         1)
(XEN) System RAM: 8191MB (8387772kB)
(XEN) SRAT: PXM 0 -> APIC 0 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 1 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 2 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 3 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 4 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 5 -> Node 0
(XEN) SRAT: Node 0 PXM 0 0-a0000
(XEN) SRAT: Node 0 PXM 0 100000-b0000000
(XEN) SRAT: Node 0 PXM 0 100000000-250000000
(XEN) NUMA: Allocated memnodemap from 24e027000 - 24e02a000
(XEN) NUMA: Using 8 for the hash shift.
(XEN) Domain heap initialised
(XEN) vesafb: framebuffer at 0xfb000000, mapped to 0xffff82c000000000, using 6144k, total 14336k
(XEN) vesafb: mode is 1280x1024x32, linelength=5120, font 8x16
(XEN) vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
(XEN) found SMP MP-table at 000ff780
(XEN) DMI present.
(XEN) APIC boot state is 'xapic'
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x808
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
(XEN) ACPI:                  wakeup_vec[aff9e00c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 0:10 APIC version 16
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 0:10 APIC version 16
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 0:10 APIC version 16
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 0:10 APIC version 16
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
(XEN) Processor #4 0:10 APIC version 16
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
(XEN) Processor #5 0:10 APIC version 16
(XEN) ACPI: IOAPIC (id[0x06] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 6, version 33, address 0xfec00000, GSI 0-23
(XEN) ACPI: IOAPIC (id[0x07] address[0xfec20000] gsi_base[24])
(XEN) IOAPIC[1]: apic_id 7, version 33, address 0xfec20000, GSI 24-55
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode:  Flat.  Using 2 I/O APICs
(XEN) ACPI: HPET id: 0x8300 base: 0xfed00000
(XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
(XEN) PCI: Not using MMCONFIG.
(XEN) Table is not found!
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) mapped APIC to ffff82c3ffffe000 (fee00000)
(XEN) mapped IOAPIC to ffff82c3ffffd000 (fec00000)
(XEN) mapped IOAPIC to ffff82c3ffffc000 (fec20000)
(XEN) IRQ limits: 56 GSI, 1112 MSI/MSI-X
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 3200.165 MHz processor.
(XEN) Initing memory sharing.
(XEN) AMD Fam10h machine check reporting enabled
(XEN) AMD-Vi: Found MSI capability block 
(XEN) AMD-Vi: ACPI Table:
(XEN) AMD-Vi:  Signature IVRS
(XEN) AMD-Vi:  Length 0x100
(XEN) AMD-Vi:  Revision 0x1
(XEN) AMD-Vi:  CheckSum 0xc3
(XEN) AMD-Vi:  OEM_Id AMD  
(XEN) AMD-Vi:  OEM_Table_Id RD890S
(XEN) AMD-Vi:  OEM_Revision 0x202031
(XEN) AMD-Vi:  Creator_Id AMD 
(XEN) AMD-Vi:  Creator_Revision 0x0
(XEN) AMD-Vi: IVRS Block:
(XEN) AMD-Vi:  Type 0x10
(XEN) AMD-Vi:  Flags 0x3e
(XEN) AMD-Vi:  Length 0xd0
(XEN) AMD-Vi:  Dev_Id 0x2
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x3
(XEN) AMD-Vi:  Dev_Id 0x0
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi:  Dev_Id Range: 0x0 -> 0x2
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x10
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0xb00
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x18
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x3
(XEN) AMD-Vi:  Dev_Id 0xa00
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi:  Dev_Id Range: 0xa00 -> 0xa07
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x28
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x900
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x30
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x800
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x50
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x600
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x0
(XEN) AMD-Vi:  Dev_Id 0x0
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x43
(XEN) AMD-Vi:  Dev_Id 0x708
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi:  Dev_Id Range: 0x708 -> 0x7ff
(XEN) AMD-Vi:  Dev_Id Alias: 0x700
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x58
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x3
(XEN) AMD-Vi:  Dev_Id 0x500
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi:  Dev_Id Range: 0x500 -> 0x501
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x68
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x3
(XEN) AMD-Vi:  Dev_Id 0x400
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi:  Dev_Id Range: 0x400 -> 0x407
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x88
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x3
(XEN) AMD-Vi:  Dev_Id 0x90
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi:  Dev_Id Range: 0x90 -> 0x92
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x3
(XEN) AMD-Vi:  Dev_Id 0x98
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi:  Dev_Id Range: 0x98 -> 0x9a
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0xa0
(XEN) AMD-Vi:  Flags 0xd7
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0xa1
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0xa3
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0xa4
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x43
(XEN) AMD-Vi:  Dev_Id 0x300
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi:  Dev_Id Range: 0x300 -> 0x3ff
(XEN) AMD-Vi:  Dev_Id Alias: 0xa4
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0xa5
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0xa8
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0xa9
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x2
(XEN) AMD-Vi:  Dev_Id 0x100
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x3
(XEN) AMD-Vi:  Dev_Id 0xb0
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi:  Dev_Id Range: 0xb0 -> 0xb2
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x0
(XEN) AMD-Vi:  Dev_Id 0x0
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x48
(XEN) AMD-Vi:  Dev_Id 0x0
(XEN) AMD-Vi:  Flags 0xd7
(XEN) AMD-Vi: IVHD Device Entry:
(XEN) AMD-Vi:  Type 0x48
(XEN) AMD-Vi:  Dev_Id 0x0
(XEN) AMD-Vi:  Flags 0x0
(XEN) AMD-Vi: Add device table entry: device id = 0x0000, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0001, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0002, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0010, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0018, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0028, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0030, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0050, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0058, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0068, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0088, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0090, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0091, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0092, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0098, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0099, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x009a, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x00a0, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x00a1, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x00a3, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x00a4, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x00a5, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x00a8, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x00a9, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x00b0, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x00b1, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x00b2, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0100, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0400, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0401, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0402, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0403, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0404, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0405, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0406, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0407, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0500, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0501, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0600, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0700, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0800, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0900, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0a00, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0a01, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0a02, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0a03, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0a04, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0a05, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0a06, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0a07, interupt table = 0x24e004000
(XEN) AMD-Vi: Add device table entry: device id = 0x0b00, interupt table = 0x24e004000
(XEN) AMD-Vi: IOMMU 0 Enabled.
(XEN) AMD-Vi: Enabling global vector map
(XEN) I/O virtualisation enabled
(XEN)  - Dom0 mode: Relaxed
(XEN) Getting VERSION: 80050010
(XEN) Getting VERSION: 80050010
(XEN) Getting ID: 0
(XEN) Getting LVT0: 700
(XEN) Getting LVT1: 400
(XEN) enabled ExtINT on CPU#0
(XEN) ESR value before enabling vector: 0x00000004  after: 0x00000000
(XEN) ENABLING IO-APIC IRQs
(XEN)  -> Using new ACK method
(XEN) init IO_APIC IRQs
(XEN)  IO-APIC (apicid-pin) 6-0, 6-16, 6-17, 6-18, 6-19, 6-20, 6-21, 6-22, 6-23, 7-0, 7-1, 7-2, 7-3, 7-4, 7-5, 7-6, 7-7, 7-8, 7-9, 7-10, 7-11, 7-12, 7-13, 7-14, 7-15, 7-16, 7-17, 7-18, 7-19, 7-20, 7-21, 7-22, 7-23, 7-24, 7-25, 7-26, 7-27, 7-28, 7-29, 7-30, 7-31 not connected.
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) number of MP IRQ sources: 15.
(XEN) number of IO-APIC #6 registers: 24.
(XEN) number of IO-APIC #7 registers: 32.
(XEN) testing the IO APIC.......................
(XEN) IO APIC #6......
(XEN) .... register #00: 06000000
(XEN) .......    : physical APIC id: 06
(XEN) .......    : Delivery Type: 0
(XEN) .......    : LTS          : 0
(XEN) .... register #01: 00178021
(XEN) .......     : max redirection entries: 0017
(XEN) .......     : PRQ implemented: 1
(XEN) .......     : IO APIC version: 0021
(XEN) .... register #02: 06000000
(XEN) .......     : arbitration: 06
(XEN) .... register #03: 07000000
(XEN) .......     : Boot DT    : 0
(XEN) .... IRQ redirection table:
(XEN)  NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
(XEN)  00 000 00  1    0    0   0   0    0    0    00
(XEN)  01 001 01  0    0    0   0   0    1    1    30
(XEN)  02 001 01  0    0    0   0   0    1    1    F0
(XEN)  03 001 01  0    0    0   0   0    1    1    38
(XEN)  04 001 01  0    0    0   0   0    1    1    F1
(XEN)  05 001 01  0    0    0   0   0    1    1    40
(XEN)  06 001 01  0    0    0   0   0    1    1    48
(XEN)  07 001 01  0    0    0   0   0    1    1    50
(XEN)  08 001 01  0    0    0   0   0    1    1    58
(XEN)  09 001 01  1    1    0   1   0    1    1    60
(XEN)  0a 001 01  0    0    0   0   0    1    1    68
(XEN)  0b 001 01  0    0    0   0   0    1    1    70
(XEN)  0c 001 01  0    0    0   0   0    1    1    78
(XEN)  0d 001 01  0    0    0   0   0    1    1    88
(XEN)  0e 001 01  0    0    0   0   0    1    1    90
(XEN)  0f 001 01  0    0    0   0   0    1    1    98
(XEN)  10 000 00  1    0    0   0   0    0    0    00
(XEN)  11 000 00  1    0    0   0   0    0    0    00
(XEN)  12 000 00  1    0    0   0   0    0    0    00
(XEN)  13 000 00  1    0    0   0   0    0    0    00
(XEN)  14 000 00  1    0    0   0   0    0    0    00
(XEN)  15 000 00  1    0    0   0   0    0    0    00
(XEN)  16 000 00  1    0    0   0   0    0    0    00
(XEN)  17 000 00  1    0    0   0   0    0    0    00
(XEN) IO APIC #7......
(XEN) .... register #00: 07000000
(XEN) .......    : physical APIC id: 07
(XEN) .......    : Delivery Type: 0
(XEN) .......    : LTS          : 0
(XEN) .... register #01: 001F8021
(XEN) .......     : max redirection entries: 001F
(XEN) .......     : PRQ implemented: 1
(XEN) .......     : IO APIC version: 0021
(XEN) .... register #02: 00000000
(XEN) .......     : arbitration: 00
(XEN) .... IRQ redirection table:
(XEN)  NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
(XEN)  00 000 00  1    0    0   0   0    0    0    00
(XEN)  01 000 00  1    0    0   0   0    0    0    00
(XEN)  02 000 00  1    0    0   0   0    0    0    00
(XEN)  03 000 00  1    0    0   0   0    0    0    00
(XEN)  04 000 00  1    0    0   0   0    0    0    00
(XEN)  05 000 00  1    0    0   0   0    0    0    00
(XEN)  06 000 00  1    0    0   0   0    0    0    00
(XEN)  07 000 00  1    0    0   0   0    0    0    00
(XEN)  08 000 00  1    0    0   0   0    0    0    00
(XEN)  09 000 00  1    0    0   0   0    0    0    00
(XEN)  0a 000 00  1    0    0   0   0    0    0    00
(XEN)  0b 000 00  1    0    0   0   0    0    0    00
(XEN)  0c 000 00  1    0    0   0   0    0    0    00
(XEN)  0d 000 00  1    0    0   0   0    0    0    00
(XEN)  0e 000 00  1    0    0   0   0    0    0    00
(XEN)  0f 000 00  1    0    0   0   0    0    0    00
(XEN)  10 000 00  1    0    0   0   0    0    0    00
(XEN)  11 000 00  1    0    0   0   0    0    0    00
(XEN)  12 000 00  1    0    0   0   0    0    0    00
(XEN)  13 000 00  1    0    0   0   0    0    0    00
(XEN)  14 000 00  1    0    0   0   0    0    0    00
(XEN)  15 000 00  1    0    0   0   0    0    0    00
(XEN)  16 000 00  1    0    0   0   0    0    0    00
(XEN)  17 000 00  1    0    0   0   0    0    0    00
(XEN)  18 000 00  1    0    0   0   0    0    0    00
(XEN)  19 000 00  1    0    0   0   0    0    0    00
(XEN)  1a 000 00  1    0    0   0   0    0    0    00
(XEN)  1b 000 00  1    0    0   0   0    0    0    00
(XEN)  1c 000 00  1    0    0   0   0    0    0    00
(XEN)  1d 000 00  1    0    0   0   0    0    0    00
(XEN)  1e 000 00  1    0    0   0   0    0    0    00
(XEN)  1f 000 00  1    0    0   0   0    0    0    00
(XEN) Using vector-based indexing
(XEN) IRQ to pin mappings:
(XEN) IRQ240 -> 0:2
(XEN) IRQ48 -> 0:1
(XEN) IRQ56 -> 0:3
(XEN) IRQ241 -> 0:4
(XEN) IRQ64 -> 0:5
(XEN) IRQ72 -> 0:6
(XEN) IRQ80 -> 0:7
(XEN) IRQ88 -> 0:8
(XEN) IRQ96 -> 0:9
(XEN) IRQ104 -> 0:10
(XEN) IRQ112 -> 0:11
(XEN) IRQ120 -> 0:12
(XEN) IRQ136 -> 0:13
(XEN) IRQ144 -> 0:14
(XEN) IRQ152 -> 0:15
(XEN) .................................... done.
(XEN) Using local APIC timer interrupts.
(XEN) calibrating APIC timer ...
(XEN) ..... CPU clock speed is 3200.0897 MHz.
(XEN) ..... host bus clock speed is 200.0054 MHz.
(XEN) ..... bus_scale = 0x0000CCD7
(XEN) [2011-10-26 13:32:49] Platform timer is 14.318MHz HPET
ÿ(XEN) [2011-10-26 13:32:49] Allocated console ring of 64 KiB.
(XEN) [2011-10-26 13:32:49] HVM: ASIDs enabled.
(XEN) [2011-10-26 13:32:49] SVM: Supported advanced features:
(XEN) [2011-10-26 13:32:49]  - Nested Page Tables (NPT)
(XEN) [2011-10-26 13:32:49]  - Last Branch Record (LBR) Virtualisation
(XEN) [2011-10-26 13:32:49]  - Next-RIP Saved on #VMEXIT
(XEN) [2011-10-26 13:32:49]  - Pause-Intercept Filter
(XEN) [2011-10-26 13:32:49] HVM: SVM enabled
(XEN) [2011-10-26 13:32:49] HVM: Hardware Assisted Paging detected.
(XEN) [2011-10-26 13:32:48] masked ExtINT on CPU#1
(XEN) [2011-10-26 13:32:48] masked ExtINT on CPU#2
(XEN) [2011-10-26 13:32:48] masked ExtINT on CPU#3
(XEN) [2011-10-26 13:32:48] masked ExtINT on CPU#4
(XEN) [2011-10-26 13:32:48] masked ExtINT on CPU#5
(XEN) [2011-10-26 13:32:49] Brought up 6 CPUs
(XEN) [2011-10-26 13:32:49] HPET's MSI mode hasn't been supported when Interrupt Remapping is enabled.
(XEN) [2011-10-26 13:32:49] ACPI sleep modes: S3
(XEN) [2011-10-26 13:32:49] MCA: Use hw thresholding to adjust polling frequency
(XEN) [2011-10-26 13:32:49] mcheck_poll: Machine check polling timer started.
(XEN) [2011-10-26 13:32:49] Xenoprofile: Failed to setup IBS LVT offset, IBSCTL = 0xffffffff
(XEN) [2011-10-26 13:32:49] *** LOADING DOMAIN 0 ***
(XEN) [2011-10-26 13:32:49] elf_parse_binary: phdr: paddr=0x1000000 memsz=0xd06000
(XEN) [2011-10-26 13:32:49] elf_parse_binary: phdr: paddr=0x1e00000 memsz=0xab0e0
(XEN) [2011-10-26 13:32:49] elf_parse_binary: phdr: paddr=0x1eac000 memsz=0x12240
(XEN) [2011-10-26 13:32:49] elf_parse_binary: phdr: paddr=0x1ebf000 memsz=0x3f2000
(XEN) [2011-10-26 13:32:49] elf_parse_binary: memory: 0x1000000 -> 0x22b1000
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: GUEST_OS = "linux"
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: ENTRY = 0xffffffff81ebf200
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81001000
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb"
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: PAE_MODE = "yes"
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: LOADER = "generic"
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: HV_START_LOW = 0xffff800000000000
(XEN) [2011-10-26 13:32:49] elf_xen_parse_note: PADDR_OFFSET = 0x0
(XEN) [2011-10-26 13:32:49] elf_xen_addr_calc_check: addresses:
(XEN) [2011-10-26 13:32:49]     virt_base        = 0xffffffff80000000
(XEN) [2011-10-26 13:32:49]     elf_paddr_offset = 0x0
(XEN) [2011-10-26 13:32:49]     virt_offset      = 0xffffffff80000000
(XEN) [2011-10-26 13:32:49]     virt_kstart      = 0xffffffff81000000
(XEN) [2011-10-26 13:32:49]     virt_kend        = 0xffffffff822b1000
(XEN) [2011-10-26 13:32:49]     virt_entry       = 0xffffffff81ebf200
(XEN) [2011-10-26 13:32:49]     p2m_base         = 0xffffffffffffffff
(XEN) [2011-10-26 13:32:49]  Xen  kernel: 64-bit, lsb, compat32
(XEN) [2011-10-26 13:32:49]  Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x22b1000
(XEN) [2011-10-26 13:32:49] PHYSICAL MEMORY ARRANGEMENT:
(XEN) [2011-10-26 13:32:49]  Dom0 alloc.:   0000000244000000->0000000248000000 (244078 pages to be allocated)
(XEN) [2011-10-26 13:32:49]  Init. ramdisk: 000000024f96e000->000000024ffff800
(XEN) [2011-10-26 13:32:49] VIRTUAL MEMORY ARRANGEMENT:
(XEN) [2011-10-26 13:32:49]  Loaded kernel: ffffffff81000000->ffffffff822b1000
(XEN) [2011-10-26 13:32:49]  Init. ramdisk: ffffffff822b1000->ffffffff82942800
(XEN) [2011-10-26 13:32:49]  Phys-Mach map: ffffffff82943000->ffffffff82b43000
(XEN) [2011-10-26 13:32:49]  Start info:    ffffffff82b43000->ffffffff82b434b4
(XEN) [2011-10-26 13:32:49]  Page tables:   ffffffff82b44000->ffffffff82b5d000
(XEN) [2011-10-26 13:32:49]  Boot stack:    ffffffff82b5d000->ffffffff82b5e000
(XEN) [2011-10-26 13:32:49]  TOTAL:         ffffffff80000000->ffffffff82c00000
(XEN) [2011-10-26 13:32:49]  ENTRY ADDRESS: ffffffff81ebf200
(XEN) [2011-10-26 13:32:49] Dom0 has maximum 6 VCPUs
(XEN) [2011-10-26 13:32:49] elf_load_binary: phdr 0 at 0xffffffff81000000 -> 0xffffffff81d06000
(XEN) [2011-10-26 13:32:50] elf_load_binary: phdr 1 at 0xffffffff81e00000 -> 0xffffffff81eab0e0
(XEN) [2011-10-26 13:32:50] elf_load_binary: phdr 2 at 0xffffffff81eac000 -> 0xffffffff81ebe240
(XEN) [2011-10-26 13:32:50] elf_load_binary: phdr 3 at 0xffffffff81ebf000 -> 0xffffffff81f77000
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0000, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0002, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0010, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0018, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0028, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0030, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0050, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0058, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0068, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0088, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0090, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0092, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0098, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x009a, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x00a0, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x00a1, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x00a3, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x00a4, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x00a5, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x00a8, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x00b0, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x00b2, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: No iommu for device 00:18.0
(XEN) [2011-10-26 13:32:50] AMD-Vi: No iommu for device 00:18.1
(XEN) [2011-10-26 13:32:50] AMD-Vi: No iommu for device 00:18.2
(XEN) [2011-10-26 13:32:50] AMD-Vi: No iommu for device 00:18.3
(XEN) [2011-10-26 13:32:50] AMD-Vi: No iommu for device 00:18.4
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0400, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0401, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0402, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0403, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0404, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0405, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0406, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0407, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0500, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0501, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0600, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0700, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vige table: device id = 0x0800, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 02482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0a00, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0a01, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0a02, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0a03, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0a04, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0a05, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0a06, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0a07, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] AMD-Vi: Setup I/O page table: device id = 0x0b00, root table = 0x2482a8000, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:32:50] Scrubbing Free RAM: ....................................................done.
(XEN) [2011-10-26 13:32:52] Xen trace buffers: disabled
(XEN) [2011-10-26 13:32:52] Std. Loglevel: All
(XEN) [2011-10-26 13:32:52] Guest Loglevel: All
(XEN) [2011-10-26 13:32:52] Xen is relinquishing VGA console.
(XEN) [2011-10-26 13:32:52] *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
(XEN) [2011-10-26 13:32:52] Freed 204kB init memory.
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.1.0konrad-next-20111022+ (root@serveerstertje) (gcc version 4.4.5 (Debian 4.4.5-8) ) #5 SMP Wed Oct 26 10:32:26 CEST 2011
[    0.000000] Command line: root=/dev/mapper/serveerstertje-root ro verbose mem=1024M console=hvc0 console=tty0 nomodeset initcall_debug debug loglevel=10 vga=794 video=vesafb earlyprintk=xen max_loop=255 loop_max_part=63 acpi_enforce_resources=lax xen-pciback.passthrough=1 xen-pciback.hide=(03:06.0)(04:00.0)(04:00.1)(04:00.2)(04:00.3)(04:00.4)(04:00.5)(04:00.6)(04:00.7)(0a:00.0)(0a:00.1)(0a:00.2)(0a:00.3)(0a:00.4)(0a:00.5)(0a:00.6)(0a:00.7)(05:00.0)(05:00.1)(07:01.0)(07:01.1)(07:01.2) pci=resource_alignment=07:01.0;07:01.1;07:01.2
[    0.000000] Freeing  9f-100 pfn range: 97 pages freed
[    0.000000] 1-1 mapping on 9f->100
[    0.000000] 1-1 mapping on aff90->100000
[    0.000000] Released 97 pages of unused memory
[    0.000000] Set 327889 page(s) to 1-1 mapping
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  Xen: 0000000000000000 - 000000000009f000 (usable)
[    0.000000]  Xen: 000000000009f000 - 0000000000100000 (reserved)
[    0.000000]  Xen: 0000000000100000 - 00000000aff90000 (usable)
[    0.000000]  Xen: 00000000aff90000 - 00000000aff9e000 (ACPI data)
[    0.000000]  Xen: 00000000aff9e000 - 00000000affe0000 (ACPI NVS)
[    0.000000]  Xen: 00000000affe0000 - 00000000b0000000 (reserved)
[    0.000000]  Xen: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  Xen: 00000000fec20000 - 00000000fec21000 (reserved)
[    0.000000]  Xen: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  Xen: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000]  Xen: 0000000100000000 - 0000000250000000 (usable)
[    0.000000] e820 remove range: 0000000040000000 - ffffffffffffffff (usable)
[    0.000000] bootconsole [xenboot0] enabled
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] user-defined physical RAM map:
[    0.000000]  user: 0000000000000000 - 000000000009f000 (usable)
[    0.000000]  user: 000000000009f000 - 0000000000100000 (reserved)
[    0.000000]  user: 0000000000100000 - 0000000040000000 (usable)
[    0.000000]  user: 00000000aff90000 - 00000000aff9e000 (ACPI data)
[    0.000000]  user: 00000000aff9e000 - 00000000affe0000 (ACPI NVS)
[    0.000000]  user: 00000000affe0000 - 00000000b0000000 (reserved)
[    0.000000]  user: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  user: 00000000fec20000 - 00000000fec21000 (reserved)
[    0.000000]  user: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  user: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000] DMI present.
[    0.000000] DMI: MSI 0 (MS-7640)  , BIOS V1.7B5 06/22/2010
[    0.000000] e820000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remo0000a0000 - 0000000000100000 (usable)
[    0.000000] No A00000] last_pfn = 0x40000 max_arch_pfn = 0x400000000
[    0.000000] foun[ffff8800000ff780] ff780
[    0.000000] initial memory map.000000] Base memory trampoline at [ffff88000009d000] 9d000 size 8192
[    0.000000] iit_memory_mapping: 0000000000000000-0000000040000000
[    0.000000]  000- 0040000000 page 4k
[    0.000000] kernel direct mapping0-1000000
[    0.000000] xen: setting RW the range fe4000 DISK: 022b1000 - 02943000
[    0.000000] ACPI: RSDP 00000)
[    0.000000] ACPI: RSDT 00000000aff90000 00048 (v01 MSI    OEMSLIC  20100622 MSFT 00000097)
[    0.000000] ACPI: FACP 00000000aff90200 00084 (v01 7640MS A7640100 20100622 MSFT 00000097)
[    0.000000] ACPI: DSDT 00000000aff905e0 09449 (v01  A7640 A7640100 00000100 INTL 20051117)
[    0.000000] ACPI: FACS 00000000aff9e000 00040
[    0.000000] ACPI: APIC 00000000aff90390 00088 (v01 7640MS A7640100 00000] ACPI: MCFG 00000000aff90420 0003C (v01 7640MS OEMMC
[    0.000000] ACPI: SLIC 00000000aff90460 00176 (v01 MSI    OEMSLIC  20100622 MSFT 00000097)
[    0.000000] ACPI: OEMB 00000000aff9e040 00072 (v01 7640MS A7640100 20100622 MSFT 00000097)
[    0.000000] ACPI: SRAT 00000000aff9a5e0 00108 (v03 AMD    FAM_F_10 00000002 AMD  00000001)
[    0.000000] ACPI: HPET 00000000aff9a6f0 00038 (v01 7640MS OEMHPET  20100622 MSFT 00000097)
[    0.000000] ACPI: IVRS 00000000aff9a730 00100 (v01  AMD     RD890S 00202031 AMD  00000000)
[    0.000000] ACPI: SSDT 00000000aff9a830 00DA4 (v01 A M I  POWERNOW 00000001 AMD  00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] Scanning NUMA topology in Northbridge 24
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-0000000040000000
[    0.000000] Initmem setup node 0 0000000000000000-0000000040000000
[    0.000000]   NODE_DATA [000000003fffb000 - 000000003fffffff]
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   empty
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x00040000
[    0.000000] On node 0 totalpages: 262031
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 488 pages reserved
[    0.000000]   DMA zone: 3431 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 4032 pages used for memmap
[    0.000000]   DMA32 zone: 25400.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] BIOS bug: APIC version is 0 for CPU 0/0x0, fixing up to 0x10
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.00000 lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
[    0.000000] ACPI: IOAPIC (id[0x06] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 6, version 255, address 0xfec00000, GSI 0-255
[    0.000000] ACPI: IOAPIC (id[0x07] address[0xfec20000] gsi_base[24])
[    0.000000] IOAPIC[1]: apic_id 7, version 255, address 0xfec20000, GSI 24-279
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8300 base: 0xfed00000
[    0.000000] SMP: Allowing 6 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 296
[    0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:6ff90000)
[    0.000000] Booting paravirtualized kernel on Xen
[    0.000000] Xen version: 4.1.3-rc1-pre (preserve-AD)
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:6 nr_node_ids:1
[    0.000000] PERCPU: Embedded 26 pages/cpu @ffff88003ff51000 s74304 r8192 d24000 u106496
[    0.000000] pcpu-alloc: s74304 r8192 d24000 u106496 alloc=26*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 257447
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: root=/dev/mapper/serveerstertje-root ro verbose mem=1024M console=hvc0 console=tty0 nomodeset initcall_debug debug loglevel=10 vga=794 video=vesafb earlyprintk=xen max_loop=255 loop_max_part=63 acpi_enforce_resources=lax xen-pciback.passthrough=1 xen-pciback.hide=(03:06.0)(04:00.0)(04:00.1)(04:00.2)(04:00.3)(04:00.4)(04:00.5)(04:00.6)(04:00.7)(0a:00.0)(0a:00.1)(0a:00.2)(0a:00.3)(0a:00.4)(0a:00.5)(0a:00.6)(0a:00.7)(05:00.0)(05:00.1)(07:01.0)(07:01.1)(07:01.2) pci=resource_alignment=07:01.0;07:01.1;07:01.2
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Placing 64MB software IO TLB between ffff88003a600000 - ffff88003e600000
[    0.000000] software IO TLB at phys 0x3a600000 - 0x3e600000
[    0.000000] Memory: 936192k/1048576k available (8666k kernel code, 452k absent, 111932k reserved, 6350k data, 784k init)
[    0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:4352 nr_irqs:1536 16
[    0.000000] xen: sci override: global_irq=9 trigger=0 polarity=1
[    0.000000] xen: registering gsi 9 triggering 0 polarity 1
[    0.000000] xen: --> pirq=9 -> irq=9 (gsi=9)
(XEN) [2011-10-26 13:32:52] IOAPIC[0]: Set PCI routing entry (6-9 -> 0x60 -> IRQ 9 Mode:1 Active:1)
[    0.000000] xen: acpi sci 9
[    0.000000] xen: --> pirq=1 -> irq=1 (gsi=1)
[    0.000000] xen: --> pirq=2 -> irq=2 (gsi=2)
[    0.000000] xen: --> pirq=3 -> irq=3 (gsi=3)
[    0.000000] xen: --> pirq=4 -> irq=4 (gsi=4)
[    0.000000] xen: --> pirq=5 -> irq=5 (gsi=5)
[    0.000000] xen: --> pirq=6 -> irq=6 (gsi=6)
[    0.000000] xen: --> pirq=7 -> irq=7 (gsi=7)
[    0.000000] xen: --> pirq=8 -> irq=8 (gsi=8)
[    0.000000] xen_map_pirq_gsi: returning irq 9 for gsi 9
[    0.000000] xen: --> pirq=9 -> irq=9 (gsi=9)
[    0.000000] xen: --> pirq=10 -> irq=10 (gsi=10)
[    0.000000] xen: --> pirq=11 -> irq=11 (gsi=11)
[    0.000000] xen: --> pirq=12 -> irq=12 (gsi=12)
[    0.000000] xen: --> pirq=13 -> irq=13 (gsi=13)
[    0.000000] xen: --> pirq=14 -> irq=14 (gsi=14)
[    0.000000] xen: --> pirq=15 -> irq=15 (gsi=15)
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled, bootconsole disabled
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.1.0konrad-next-20111022+ (root@serveerstertje) (gcc version 4.4.5 (Debian 4.4.5-8) ) #5 SMP Wed Oct 26 10:32:26 CEST 2011
[    0.000000] Command line: root=/dev/mapper/serveerstertje-root ro verbose mem=1024M console=hvc0 console=tty0 nomodeset initcall_debug debug loglevel=10 vga=794 video=vesafb earlyprintk=xen max_loop=255 loop_max_part=63 acpi_enforce_resources=lax xen-pciback.passthrough=1 xen-pciback.hide=(03:06.0)(04:00.0)(04:00.1)(04:00.2)(04:00.3)(04:00.4)(04:00.5)(04:00.6)(04:00.7)(0a:00.0)(0a:00.1)(0a:00.2)(0a:00.3)(0a:00.4)(0a:00.5)(0a:00.6)(0a:00.7)(05:00.0)(05:00.1)(07:01.0)(07:01.1)(07:01.2) pci=resource_alignment=07:01.0;07:01.1;07:01.2
[    0.000000] Freeing  9f-100 pfn range: 97 pages freed
[    0.000000] 1-1 mapping on 9f->100
[    0.000000] 1-1 mapping on aff90->100000
[    0.000000] Released 97 pages of unused memory
[    0.000000] Set 327889 page(s) to 1-1 mapping
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  Xen: 0000000000000000 - 000000000009f000 (usable)
[    0.000000]  Xen: 000000000009f000 - 0000000000100000 (reserved)
[    0.000000]  Xen: 0000000000100000 - 00000000aff90000 (usable)
[    0.000000]  Xen: 00000000aff90000 - 00000000aff9e000 (ACPI data)
[    0.000000]  Xen: 00000000aff9e000 - 00000000affe0000 (ACPI NVS)
[    0.000000]  Xen: 00000000affe0000 - 00000000b0000000 (reserved)
[    0.000000]  Xen: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  Xen: 00000000fec20000 - 00000000fec21000 (reserved)
[    0.000000]  Xen: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  Xen: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000]  Xen: 0000000100000000 - 0000000250000000 (usable)
[    0.000000] e820 remove range: 0000000040000000 - ffffffffffffffff (usable)
[    0.000000] bootconsole [xenboot0] enabled
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] user-defined physical RAM map:
[    0.000000]  user: 0000000000000000 - 000000000009f000 (usable)
[    0.000000]  user: 000000000009f000 - 0000000000100000 (reserved)
[    0.000000]  user: 0000000000100000 - 0000000040000000 (usable)
[    0.000000]  user: 00000000aff90000 - 00000000aff9e000 (ACPI data)
[    0.000000]  user: 00000000aff9e000 - 00000000affe0000 (ACPI NVS)
[    0.000000]  user: 00000000affe0000 - 00000000b0000000 (reserved)
[    0.000000]  user: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  user: 00000000fec20000 - 00000000fec21000 (reserved)
[    0.000000]  user: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  user: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000] DMI present.
[    0.000000] DMI: MSI MS-7640/890FXA-GD70 (MS-7640)  , BIOS V1.7B5 06/22/2010
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x40000 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [ffff8800000ff780] ff780
[    0.000000] initial memory mapped : 0 - 02943000
[    0.000000] Base memory trampoline at [ffff88000009d000] 9d000 size 8192
[    0.000000] init_memory_mapping: 0000000000000000-0000000040000000
[    0.000000]  0000000000 - 0040000000 page 4k
[    0.000000] kernel direct mapping tables up to 40000000 @ dfe000-1000000
[    0.000000] xen: setting RW the range fe4000 - 1000000
[    0.000000] RAMDISK: 022b1000 - 02943000
[    0.000000] ACPI: RSDP 00000000000fb120 00014 (v00 ACPIAM)
[    0.000000] ACPI: RSDT 00000000aff90000 00048 (v01 MSI    OEMSLIC  20100622 MSFT 00000097)
[    0.000000] ACPI: FACP 00000000aff90200 00084 (v01 7640MS A7640100 20100622 MSFT 00000097)
[    0.000000] ACPI: DSDT 00000000aff905e0 09449 (v01  A7640 A7640100 00000100 INTL 20051117)
[    0.000000] ACPI: FACS 00000000aff9e000 00040
[    0.000000] ACPI: APIC 00000000aff90390 00088 (v01 7640MS A7640100 20100622 MSFT 00000097)
[    0.000000] ACPI: MCFG 00000000aff90420 0003C (v01 7640MS OEMMCFG  20100622 MSFT 00000097)
[    0.000000] ACPI: SLIC 00000000aff90460 00176 (v01 MSI    OEMSLIC  20100622 MSFT 00000097)
[    0.000000] ACPI: OEMB 00000000aff9e040 00072 (v01 7640MS A7640100 20100622 MSFT 00000097)
[    0.000000] ACPI: SRAT 00000000aff9a5e0 00108 (v03 AMD    FAM_F_10 00000002 AMD  00000001)
[    0.000000] ACPI: HPET 00000000aff9a6f0 00038 (v01 7640MS OEMHPET  20100622 MSFT 00000097)
[    0.000000] ACPI: IVRS 00000000aff9a730 00100 (v01  AMD     RD890S 00202031 AMD  00000000)
[    0.000000] ACPI: SSDT 00000000aff9a830 00DA4 (v01 A M I  POWERNOW 00000001 AMD  00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] Scanning NUMA topology in Northbridge 24
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-0000000040000000
[    0.000000] Initmem setup node 0 0000000000000000-0000000040000000
[    0.000000]   NODE_DATA [000000003fffb000 - 000000003fffffff]
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   empty
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x00040000
[    0.000000] On node 0 totalpages: 262031
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 488 pages reserved
[    0.000000]   DMA zone: 3431 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 4032 pages used for memmap
[    0.000000]   DMA32 zone: 254016 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] BIOS bug: APIC version is 0 for CPU 0/0x0, fixing up to 0x10
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
[    0.000000] ACPI: IOAPIC (id[0x06] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 6, version 255, address 0xfec00000, GSI 0-255
[    0.000000] ACPI: IOAPIC (id[0x07] address[0xfec20000] gsi_base[24])
[    0.000000] IOAPIC[1]: apic_id 7, version 255, address 0xfec20000, GSI 24-279
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8300 base: 0xfed00000
[    0.000000] SMP: Allowing 6 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 296
[    0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:6ff90000)
[    0.000000] Booting paravirtualized kernel on Xen
[    0.000000] Xen version: 4.1.3-rc1[    0.597265] pciback 0000:04:00.4: PCI INT C disabled
[    0.597312] xen: registering gsi 41 triggering 0 polarity 1
[    0.597317] xen: --> pirq=41 -> irq=41 (gsi=41)
[    0.597331] pciback 0000:04:00.3: PCI INT B -> GSI 41 (level, low) -> IRQ 41
[    0.597339] pciback 0000:04:00.3: PCI INT B disabled
[    0.597425] xen: registering gsi 41 triggering 0 polarity 1
[    0.597427] xen_map_pirq_gsi: returning irq 41 for gsi 41
[    0.597428] xen: --> pirq=41 -> irq=41 (gsi=41)
[    0.597430] Already setup the GSI :41
[    0.597432] pciback 0000:04:00.2: PCI INT B -> GSI 41 (level, low) -> IRQ 41
[    0.597439] pciback 0000:04:00.2: PCI INT B disabled
[    0.597487] xen: registering gsi 40 triggering 0 polarity 1
[    0.597492] xen: --> pirq=40 -> irq=40 (gsi=40)
[    0.597507] pciback 0000:04:00.1: PCI INT A -> GSI 40 (level, low) -> IRQ 40
[    0.597514] pciback 0000:04:00.1: PCI INT A disabled
[    0.597562] xen: registering gsi 40 triggering 0 polarity 1
[    0.597564] xen_map_pirq_gsi: returning irq 40 for gsi 40
[    0.597565] xen: --> pirq=40 -> irq=40 (gsi=40)
[    0.597567] Already setup the GSI :40
[    0.597569] pciback 0000:04:00.0: PCI INT A -> GSI 40 (level, low) -> IRQ 40
[    0.597576] pciback 0000:04:00.0: PCI INT A disabled
[    0.597617] xen: registering gsi 33 triggering 0 polarity 1
[    0.597622] xen: --> pirq=33 -> irq=33 (gsi=33)
[    0.597637] pciback 0000:05:00.1: PCI INT B -> GSI 33 (level, low) -> IRQ 33
[    0.597644] pciback 0000:05:00.1: PCI INT B disabled
[    0.597686] pciback 0000:05:00.0: enabling device (0000 -> 0003)
[    0.597690] xen: registering gsi 32 triggering 0 polarity 1
[    0.597695] xen: --> pirq=32 -> irq=32 (gsi=32)
[    0.597710] pciback 0000:05:00.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32
[    0.597715] pciback 0000:05:00.0: PCI INT A disabled
[    0.597752] pciback 0000:07:01.2: enabling device (0114 -> 0116)
[    0.597758] xen: registering gsi 46 triggering 0 polarity 1
[    0.597762] xen: --> pirq=46 -> irq=46 (gsi=46)
[    0.597777] pciback 0000:07:01.2: PCI INT C -> GSI 46 (level, low) -> IRQ 46
[    0.597785] pciback 0000:07:01.2: PCI INT C disabled
[    0.597825] pciback 0000:07:01.1: enabling device (0114 -> 0116)
[    0.597830] xen: registering gsi 45 triggering 0 polarity 1
[    0.597834] xen: --> pirq=45 -> irq=45 (gsi=45)
[    0.597850] pciback 0000:07:01.1: PCI INT B -> GSI 45 (level, low) -> IRQ 45
[    0.597858] pciback 0000:07:01.1: PCI INT B disabled
[    0.597893] pciback 0000:07:01.0: enabling device (0114 -> 0116)
[    0.597898] xen: registering gsi 44 triggering 0 polarity 1
[    0.597903] xen: --> pirq=44 -> irq=44 (gsi=44)
[    0.597917] pciback 0000:07:01.0: PCI INT A -> GSI 44 (level, low) -> IRQ 44
[    0.597925] pciback 0000:07:01.0: PCI INT A disabled
[    0.597979] xen: registering gsi 31 triggering 0 polarity 1
[    0.597983] xen: --> pirq=31 -> irq=31 (gsi=31)
[    0.597999] pciback 0000:0a:00.7: PCI INT D -> GSI 31 (level, low) -> IRQ 31
[    0.598007] pciback 0000:0a:00.7: PCI INT D disabled
[    0.598067] xen: registering gsi 31 triggering 0 polarity 1
[    0.598069] xen_map_pirq_gsi: returning irq 31 for gsi 31
[    0.598070] xen: --> pirq=31 -> irq=31 (gsi=31)
[    0.598072] Already setup the GSI :31
[    0.598074] pciback 0000:0a:00.6: PCI INT D -> GSI 31 (level, low) -> IRQ 31
[    0.598081] pciback 0000:0a:00.6: PCI INT D disabled
[    0.598139] xen: registering gsi 30 triggering 0 polarity 1
[    0.598144] xen: --> pirq=30 -> irq=30 (gsi=30)
[    0.598159] pciback 0000:0a:00.5: PCI INT C -> GSI 30 (level, low) -> IRQ 30
[    0.598167] pciback 0000:0a:00.5: PCI INT C disabled
[    0.598219] xen: registering gsi 30 triggering 0 polarity 1
[    0.598221] xen_map_pirq_gsi: returning irq 30 for gsi 30
[    0.598222] xen: --> pirq=30 -> irq=30 (gsi=30)
[    0.598224] Already setup the GSI :30
[    0.598225] pciback 0000:0a:00.4: PCI INT C -> GSI 30 (level, low) -> IRQ 30
[    0.598233] pciback 0000:0a:00.4: PCI INT C disabled
[    0.598287] xen: registering gsi 29 triggering 0 polarity 1
[    0.598293] xen: --> pirq=29 -> irq=29 (gsi=29)
[    0.598309] pciback 0000:0a:00.3: PCI INT B -> GSI 29 (level, low) -> IRQ 29
[    0.598317] pciback 0000:0a:00.3: PCI INT B disabled
[    0.598369] xen: registering gsi 29 triggering 0 polarity 1
[    0.598371] xen_map_pirq_gsi: returning irq 29 for gsi 29
[    0.598372] xen: --> pirq=29 -> irq=29 (gsi=29)
[    0.598373] Already setup the GSI :29
[    0.598375] pciback 0000:0a:00.2: PCI INT B -> GSI 29 (level, low) -> IRQ 29
[    0.598383] pciback 0000:0a:00.2: PCI INT B disabled
[    0.598435] xen: registering gsi 28 triggering 0 polarity 1
[    0.598440] xen: --> pirq=28 -> irq=28 (gsi=28)
[    0.598455] pciback 0000:0a:00.1: PCI INT A -> GSI 28 (level, low) -> IRQ 28
[    0.598463] pciback 0000:0a:00.1: PCI INT A disabled
[    0.598546] xen: registering gsi 28 triggering 0 polarity 1
[    0.598549] xen_map_pirq_gsi: returning irq 28 for gsi 28
[    0.598550] xen: --> pirq=28 -> irq=28 (gsi=28)
[    0.598552] Already setup the GSI :28
[    0.598553] pciback 0000:0a:00.0: PCI INT A -> GSI 28 (level, low) -> IRQ 28
[    0.598563] pciback 0000:0a:00.0: PCI INT A disabled
[    0.599257] xen-pciback: backend is passthrough
[    0.600529] initcall xen_pcibk_init+0x0/0x136 returned 0 after 3529 usecs
[    0.600533] calling  pty_init+0x0/0x345 @ 1
[    0.601755] initcall pty_init+0x0/0x345 returned 0 after 1186 usecs
[    0.601759] calling  sysrq_init+0x0/0x78 @ 1
[    0.601772] initcall sysrq_init+0x0/0x78 returned 0 after 11 usecs
[    0.601774] calling  xen_hvc_init+0x0/0x13b @ 1
[    0.615583] initcall xen_hvc_init+0x0/0x13b returned 0 after 13468 usecs
[    0.615593] calling  serial8250_init+0x0/0x194 @ 1
[    0.615599] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.325076] initcall serial8250_init+0x0/0x194 returned 0 after 692832 usecs
[    1.326000] calling  serial8250_pnp_init+0x0/0x12 @ 1
[    1.369511] initcall serial8250_pnp_init+0x0/0x12 returned 0 after 28497 usecs
[    1.370439] calling  serial8250_pci_init+0x0/0x1b @ 1
[    1.388272] initcall serial8250_pci_init+0x0/0x1b returned 0 after 3106 usecs
[    1.389188] calling  rand_initialize+0x0/0x30 @ 1
[    1.389188] initcall rand_initialize+0x0/0x30 returned 0 after 7 usecs
[    1.389188] calling  hpet_init+0x0/0x6a @ 1
[    1.415234] hpet_acpi_add: no address or irqs in _CRS
[    1.422052] initcall hpet_init+0x0/0x6a returned 0 after 8083 usecs
[    1.423020] calling  nvram_init+0x0/0x82 @ 1
[    1.434628] Non-volatile memory driver v1.3
[    1.435572] initcall nvram_init+0x0/0x82 returned 0 after 6715 usecs
[    1.435572] calling  mod_init+0x0/0x5a @ 1
[    1.435572] initcall mod_init+0x0/0x5a returned -19 after 0 usecs
[    1.435572] calling  agp_init+0x0/0x26 @ 1
[    1.435572] Linux agpgart interface v0.103
[    1.464140] initcall agp_init+0x0/0x26 returned 0 after 5419 usecs
[    1.464140] calling  agp_amd64_mod_init+0x0/0x22 @ 1
[    1.489110] initcall agp_amd64_mod_init+0x0/0x22 returned -19 after 20295 usecs
[    1.490076] calling  agp_intel_init+0x0/0x29 @ 1
[    1.502930] initcall agp_intel_init+0x0/0x29 returned 0 after 1093 usecs
[    1.503882] calling  drm_core_init+0x0/0x139 @ 1
[    1.516155] [drm] Initialized drm 1.1.0 20060810
[    1.517098] initcall drm_core_init+0x0/0x139 returned 0 after 6485 usecs
[    1.517098] calling  i915_init+0x0/0x8d @ 1
[    1.517098] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module!
[    1.517098] initcall i915_init+0x0/0x8d returned -19 after 5649 usecs
[    1.517098] calling  cn_proc_init+0x0/0x3d @ 1
[    1.517098] initcall cn_proc_init+0x0/0x3d returned 0 after 1 usecs
[    1.517098] calling  topology_sysfs_init+0x0/0x58 @ 1
[    1.562364] initcall topology_sysfs_init+0x0/0x58 returned 0 after 55 usecs
[    1.563316] calling  brd_init+0x0/0x1d4 @ 1
[    1.632667] brd: module loaded
[    1.633551] initcall brd_init+0x0/0x1d4 returned 0 after 65469 usecs
[    1.633551] calling  loop_init+0x0/0x139 @ 1
[    3.283586] loop: module loaded
[    3.284463] initcall loop_init+0x0/0x139 returned 0 after 1594863 usecs
[    3.299480] calling  xlblk_init+0x0/0x9d @ 1
[    3.310197] initcall xlblk_init+0x0/0x9d returned 0 after 2920 usecs
[    3.311123] calling  xen_blkif_init+0x0/0x256 @ 1
[    3.327025] initcall xen_blkif_init+0x0/0x256 returned 0 after 2103 usecs
[    3.327965] calling  mac_hid_init+0x0/0x22 @ 1
[    3.327965] initcall mac_hid_init+0x0/0x22 returned 0 after 14 usecs
[    3.342212] calling  spi_transport_init+0x0/0x79 @ 1
[    3.352779] initcall spi_transport_init+0x0/0x79 returned 0 after 2042 usecs
[    3.353746] calling  init_sd+0x0/0x14a @ 1
[    3.368737] initcall init_sd+0x0/0x14a returned 0 after 3147 usecs
[    3.369678] calling  init_sr+0x0/0x46 @ 1
[    3.381976] initcall init_sr+0x0/0x46 returned 0 after 1290 usecs
[    3.382943] calling  init_sg+0x0/0x122 @ 1
[    3.395072] initcall init_sg+0x0/0x122 returned 0 after 1284 usecs
[    3.396009] calling  ahci_init+0x0/0x1b @ 1
[    3.407522] ahci 0000:00:11.0: version 3.0
[    3.413464] xen: registering gsi 19 triggering 0 polarity 1
[    3.419344] xen: --> pirq=19 -> irq=19 (gsi=19)
(XEN) [2011-10-26 13:32:56] IOAPIC[0]: Set PCI routing entry (6-19 -> 0xb1 -> IRQ 19 Mode:1 Active:1)
[    3.425244] ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    3.431310] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode
[    3.432170] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part 
[    3.464041] scsi0 : ahci
[    3.474217] scsi1 : ahci
[    3.483443] scsi2 : ahci
[    3.491947] scsi3 : ahci
[    3.500892] ata1: SATA max UDMA/133 abar m1024@0xf98ff000 port 0xf98ff100 irq 342
[    3.501697] ata2: SATA max UDMA/133 abar m1024@0xf98ff000 port 0xf98ff180 irq 342
[    3.501697] ata3: SATA max UDMA/133 abar m1024@0xf98ff000 port 0xf98ff200 irq 342
[    3.501697] ata4: SATA max UDMA/133 abar m1024@0xf98ff000 port 0xf98ff280 irq 342
[    3.524242] calling  2_async_port_probe+0x0/0x70 @ 25
[    3.524289] calling  3_async_port_probe+0x0/0x70 @ 5
[    3.535584] calling  4_async_port_probe+0x0/0x70 @ 1111
[    3.541484] calling  5_async_port_probe+0x0/0x70 @ 1749
[    3.542862] initcall ahci_init+0x0/0x1b returned 0 after 132927 usecs
[    3.542865] calling  ahci_init+0x0/0x19 @ 1
[    3.545713] initcall ahci_init+0x0/0x19 returned -19 after 2772 usecs
(XEN) [2011-10-26 13:32:56] IOAPIC[1]: Set PCI routing entry (7-27 -> 0xc9 -> IRQ 51 Mode:1 Active:1)
[    3.545717] calling  net_olddevs_init+0x0/0x9f @ 1
[    3.545723] initcall net_olddevs_init+0x0/0x9f returned 0 after 4 usecs
[    3.545725] calling  realtek_init+0x0/0x12 @ 1
(XEN) [2011-10-26 13:32:56] IOAPIC[0]: Set PCI routing entry (6-17 -> 0xd9 -> IRQ 17 Mode:1 Active:1)
[    3.546956] initcall realtek_init+0x0/0x12 returned 0 after 1194 usecs
[    3.546960] calling  tun_init+0x0/0x93 @ 1
[    3.546961] tun: Universal TUN/TAP device driver, 1.6
[    3.546963] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    3.547875] initcall tun_init+0x0/0x93 returned 0 after 877 usecs
[    3.547885] calling  veth_init+0x0/0x12 @ 1
[    3.547894] initcall veth_init+0x0/0x12 returned 0 after 1 usecs
[    3.547902] calling  tg3_init+0x0/0x1b @ 1
[    3.549576] initcall tg3_init+0x0/0x1b returned 0 after 1623 usecs
[    3.549580] calling  e100_init_module+0x0/0x5d @ 1
(XEN) [2011-10-26 13:32:56] IOAPIC[0]: Set PCI routing entry (6-18 -> 0x22 -> IRQ 18 Mode:1 Active:1)
[    3.549582] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[    3.549584] e100: Copyright(c) 1999-2006 Intel Corporation
[    3.550898] initcall e100_init_module+0x0/0x5d returned 0 after 1278 usecs
[    3.550901] calling  e1000_init_module+0x0/0x87 @ 1
[    3.550903] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[    3.550904] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    3.552794] initcall e1000_init_module+0x0/0x87 returned 0 after 1839 usecs
[    3.552797] calling  sky2_init_module+0x0/0x29 @ 1
[    3.552798] sky2: driver version 1.29
[    3.554742] initcall sky2_init_module+0x0/0x29 returned 0 after 1890 usecs
[    3.554746] calling  init_nic+0x0/0x1b @ 1
[    3.556111] initcall init_nic+0x0/0x1b returned 0 after 1324 usecs
[    3.556114] calling  rtl8139_init_module+0x0/0x1b @ 1
[    3.557429] initcall rtl8139_init_module+0x0/0x1b returned 0 after 1276 usecs
[    3.557432] calling  rtl8169_init_module+0x0/0x1b @ 1
[    3.558130] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    3.558165] xen: registering gsi 46 triggering 0 polarity 1
[    3.558174] xen_map_pirq_gsi: returning irq 46 for gsi 46
[    3.558175] xen: --> pirq=46 -> irq=46 (gsi=46)
[    3.558177] Already setup the GSI :46
[    3.558219] r8169 0000:09:00.0: PCI INT A -> GSI 46 (level, low) -> IRQ 46
[    3.558266] r8169 0000:09:00.0: setting latency timer to 64
[    3.563011] r8169 0000:09:00.0: eth0: RTL8168d/8111d at 0xffffc900001a2000, 40:61:86:f4:67:d9, XID 081000c0 IRQ 343
[    3.563014] r8169 0000:09:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    3.563751] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    3.563787] xen: registering gsi 51 triggering 0 polarity 1
[    3.563803] xen: --> pirq=51 -> irq=51 (gsi=51)
[    3.563831] r8169 0000:08:00.0: PCI INT A -> GSI 51 (level, low) -> IRQ 51
[    3.563873] r8169 0000:08:00.0: setting latency timer to 64
[    3.567925] r8169 0000:08:00.0: eth1: RTL8168d/8111d at 0xffffc900001a6000, 40:61:86:f4:67:d8, XID 081000c0 IRQ 344
[    3.567928] r8169 0000:08:00.0: eth1: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    3.569238] initcall rtl8169_init_module+0x0/0x1b returned 0 after 11520 usecs
[    3.569241] calling  netif_init+0x0/0x67 @ 1
[    3.569244] initcall netif_init+0x0/0x67 returned 0 after 0 usecs
[    3.569246] calling  netback_init+0x0/0x21d @ 1
[    3.574859] initcall netback_init+0x0/0x21d returned 0 after 5471 usecs
[    3.574862] calling  cdrom_init+0x0/0x6a @ 1
[    3.574885] initcall cdrom_init+0x0/0x6a returned 0 after 20 usecs
[    3.574887] calling  nonstatic_sysfs_init+0x0/0x12 @ 1
[    3.574891] initcall nonstatic_sysfs_init+0x0/0x12 returned 0 after 1 usecs
[    3.574893] calling  yenta_socket_init+0x0/0x1b @ 1
[    3.576159] initcall yenta_socket_init+0x0/0x1b returned 0 after 1228 usecs
[    3.576163] calling  mon_init+0x0/0x100 @ 1
[    3.580475] initcall mon_init+0x0/0x100 returned 0 after 4202 usecs
[    3.580478] calling  ehci_hcd_init+0x0/0xef @ 1
[    3.580480] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.580482] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96
[    3.581781] xen: registering gsi 17 triggering 0 polarity 1
[    3.581803] xen: --> pirq=17 -> irq=17 (gsi=17)
[    3.581835] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    3.581872] ehci_hcd 0000:00:12.2: EHCI Host Controller
[    3.581903] drivers/usb/core/inode.c: creating file 'devices'
[    3.581908] drivers/usb/core/inode.c: creating file '001'
[    3.583225] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[    3.583237] ehci_hcd 0000:00:12.2: reset hcs_params 0x101505 dbg=1 cc=1 pcc=5 ordered !ppc ports=5
[    3.583241] ehci_hcd 0000:00:12.2: reset hcc_params a072 thresh 7 uframes 256/512/1024
[    3.583245] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    3.584193] QUIRK: Enable AMD PLL fix
[    3.584193] ehci_hcd 0000:00:12.2: debug port 1
[    3.584193] ehci_hcd 0000:00:12.2: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    3.584193] ehci_hcd 0000:00:12.2: MWI active
[    3.584193] ehci_hcd 0000:00:12.2: supports USB remote wakeup
[    3.584193] ehci_hcd 0000:00:12.2: irq 17, io mem 0xf98ff400
[    3.584193] ehci_hcd 0000:00:12.2: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    3.584193] ehci_hcd 0000:00:12.2: init command 0010005 (park)=0 ithresh=1 period=512 RUN
[    3.591384] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[    3.591434] usb usb1: default language 0x0409
[    3.591441] usb usb1: udev 1, busnum 1, minor = 0
[    3.591442] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.591444] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.591446] usb usb1: Product: EHCI Host Controller
[    3.591447] usb usb1: Manufacturer: Linux 3.1.0konrad-next-20111022+ ehci_hcd
[    3.591449] usb usb1: SerialNumber: 0000:00:12.2
[    3.593538] usb usb1: usb_probe_device
[    3.593542] usb usb1: configuration #1 chosen from 1 choice
[    3.593555] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    3.594846] hub 1-0:1.0: usb_probe_interface
[    3.594849] hub 1-0:1.0: usb_probe_interface - got id
[    3.594851] hub 1-0:1.0: USB hub found
[    3.594860] hub 1-0:1.0: 5 ports detected
[    3.594861] hub 1-0:1.0: standalone hub
[    3.594863] hub 1-0:1.0: no power switching (usb 1.0)
[    3.594864] hub 1-0:1.0: individual port over-current protection
[    3.594866] hub 1-0:1.0: power on to power good time: 20ms
[    3.594869] hub 1-0:1.0: local power source is good
[    3.594871] hub 1-0:1.0: trying to enable port power on non-switchable hub
[    3.594913] drivers/usb/core/inode.c: creating file '001'
[    3.595735] xen: registering gsi 17 triggering 0 polarity 1
[    3.595744] xen_map_pirq_gsi: returning irq 17 for gsi 17
[    3.595746] xen: --> pirq=17 -> irq=17 (gsi=17)
[    3.595748] Already setup the GSI :17
[    3.595752] ehci_hGSI 17 (level, low) -> IRQ 17
[    3.595792] ehci_hcd 000ntroller
[    3.595806] drivers/usb/core/inode.c: creating file '002'
[    3.596710] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[    3.596724] ehci_hcd 0000:00:13.2: reset hcs_params 0x101505 dbg=1 cc=1 pcc=5 ordered !ppc ports=5
[    3.596728] ehci_hcd 0000:00:13.2: reset hcc_params a072 thresh 7 uframes 256/512/1024
[    3.596733] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    3.597188] ehci_hcd 0000:00:13.2: debug port 1
[    3.597192] ehci_hcd 0000:00:13.2: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    3.597205] ehci_hcd 0000:00:13.2: MWI active
[    3.597207] ehci_hcd 0000:00:13.2: supports USB remote wakeup
[    3.597216] ehci_hcd 0000:00:13.2: irq 17, io mem 0xf98ff800
[    3.597220] ehci_hcd 0000:00:13.2: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    3.597227] ehci_hcd 0000:00:13.2: init command 0010005 (park)=0 ithresh=1 period=512 RUN
[    3.605473] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[    3.605528] usb usb2: default language 0x0409
[    3.605533] usb usb2: udev 1, busnum 2, minor = 128
[    3.605535] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    3.605537] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.605539] usb usb2: Product: EHCI Host Controller
[    3.605540] usb usb2: Manufacturer: Linux 3.1.0konrad-next-20111022+ ehci_hcd
[    3.605542] usb usb2: SerialNumber: 0000:00:13.2
[    3.608036] usb usb2: usb_probe_device
[    3.608041] usb usb2: configuration #1 chosen from 1 choice
[    3.608085] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[    3.608880] hub 2-0:1.0: usb_probeb 2-0:1.0: usb_probe_interface - got id
[  b found
[    3.608894] hub 2-0:1.0: 5 ports detected
[    3.608895] hub 2-0:1.0: standalone hub
[    3.608896] hub 2-0:1.0: no power switching (usb 1.0)
[    3.608898] hub 2-0:1.0: individual port over-current protection
[    3.608900] hub 2-0:1.0: power on to power good time: 20ms
[    3.608903] hub 2-0:1.0: local power source is good
[    3.608905] hub 2-0:1.0: trying to enable port power on non-switchable hub
[    3.608943] drivers/usb/core/inode.c: creating file '001'
[    3.609750] xen: registering gsi 17 triggering 0 polarity 1
[    3.609761] xen_map_pirq_gsi: returning irq 17 for gsi 17
[    3.609763] xen: --> pirq=17 -> irq=17 (gsi=17)
[    3.609765] Already setup the GSI :17
[    3.609768] ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    3.609806] ehci_hcd 0000:00:16.2: EHCI Host Controller
[    3.609815] drivers/usb/core/inode.c: creating file '003'
[    3.611137] ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
[    3.611151] ehci_hcd 0000:00:16.2: reset hcs_params 0x101404 dbg=1 cc=1 pcc=4 ordered !ppc ports=4
[    3.611155] ehci_hcd 0000:00:16.2: reset hcc_params a072 thresh 7 uframes 256/512/1024
[    3.611160] ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    3.612106] ehci_hcd 0000:00:16.2: debug port 1
[    3.612106] ehci_hcd 0000:00:16.2: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    3.612106] ehci_hcd 0000:00:16.2: MWI active
[    3.612106] ehci_hcd 0000:00:16.2: supports USB remote wakeup
[    3.612106] ehci_hcd 0000:00:16.2: irq 17, io mem 0xf98ffc00
[    3.612106] ehci_hcd 0000:00:16.2: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    3.612106] ehci_hcd 0000:00:16.2: init command 0010005 (park)=0 ithresh=1 period=512 RUN
[    3.620171] ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
[    3.620275] usb usb3: default language 0x0409
[    3.620281] usb usb3: udev 1, busnum 3, minor = 256
[    3.620283] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    3.620285] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.620286] usb usb3: Product: EHCI Host Controller
[    3.620288] uer: Linux 3.1.0konrad-next-20111022+ ehci_hcd
[    3.620290] usb usb3: SerialNumber: 0000:00:16.2
[    3.622601] us_device
[    3.622605] usb usb3: configurat[    3.622617] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[    3.625040] hub 3-0:1.0: usb_probe_interface
[    3.625044] hub 3-0:1.0: usb_probe_interface - got id
[    3.625045] hub 3-0:1.0: USB hub found
[    3.625093] hub 3-0:1.0: 4 ports detected
[    3.625094] hub 3-0:1.0: standalone hub
[    3.625096] hub 3-0:1.0: no power switching (usb 1.0)
[    3.625098] hub 3-0:1.0: individual port over-current protection
[    3.625099] hub 3-0:1.0: power on to power good time: 20ms
[    3.625104] hub 3-0:1.0: local power source is good
[    3.625106] hub 3-0:1.0: trying to enable port power on non-switchable hub
[    3.625146] drivers/usb/core/inode.c: creating file '001'
[    3.627598] initcall ehci_hcd_init+0x0/0xef returned 0 after 46006 usecs
[    3.627602] calling  ohci_hcd_mod_init+0x0/0xbf @ 1
[    3.627604] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.627605] ohci_hcd: block sizes: ed 80 td 96
[    3.629535] xen: registering gsi 18 triggering 0 polarity 1
[    3.629555] xen: --> pirq=18 -> irq=18 (gsi=18)
[    3.629587] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    3.629625] ohci_hcd 0000:00:12.0: OHCI Host Controller
[    3.629638] drivers/usb/core/inode.c: creating file '004'
[    3.631023] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
[    3.631037] ohci_hcd 0000:00:12.0: enabled AMD prefetch quirk
[    3.631636] ohci_hcd 0000:00:12.0: created debug files
[    3.631638] ohci_hcd 0000:00:12.0: supports USB remote wakeup
[    3.631688] ohci_hcd 0000:00:12.0: irq 18, io mem 0xf98fb000
[    3.687293] ohci_hcd 0000:00:12.0: OHCI controller state
[    3.687301] ohci_hcd 0000:00:12.0: OHCI 1.0, NO legacy support registers
[    3.687305] ohci_hcd 0000:00:12.0: control 0x283 RWC HCFS=operational CBSR=3
[    3.687308] ohci_hcd 0000:00:12.0: cmdstatus 0x00000 SOC=0
[    3.687313] ohci_hcd 0000:00:12.0: intrstatus 0x00000004 SF
[    3.687317] ohci_hcd 0000:00:12.0: intrenable 0x8000005a MIE RHSC UE RD WDH
[    3.687327] ohci_hcd 0000:00:12.0: hcca frame #0005
[    3.687331] ohci_hcd 0000:00:12.0: roothub.a 02001205 POTPGT=2 NOCP NPS NDP=5(5)
[    3.687335] ohci_hcd 0000:00:12.0: roothub.b 00000000 PPCM=0000 DR=0000
[    3.687338] ohci_hcd 0000:00:12.0: roothub.status 00008000 DRWE
[    3.687342] ohci_hcd 0000:00:12.0: roothub.portstatus [0] 0x00000100 PPS
[    3.687345] ohci_hcd 0000:00:12.0: roothub.portstatus [1] 0x00000100 PPS
[    3.687349] ohci_hcd 0000:00:12.0: roothub.portstatus [2] 0x00000100 PPS
[    3.687352] ohci_hcd 0000:00:12.0: roothub.portstatus [3] 0x00000100 PPS
[    3.687355] ohci_hcd 0000:00:12.0: roothub.portstatus [4] 0x00000100 PPS
[    3.687372] usb usb4: default language 0x0409
[    3.687378] usb usb4: udev 1, busnum 4, minor = 384
[    3.687380] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    3.687381] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.687383] usb usb4: Product: OHCI Host Controller
[    3.687385] usb usb4: Manufacturer: Linux 3.1.0konrad-next-20111022+ ohci_hcd
[    3.687386] usb usb4: SerialNumber: 0000:00:12.0
[    3.688728] usb usb4: usb_probe_device
[    3.688732] usb usb4: configuration #1 chosen from 1 choice
[    3.688743] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[    3.690030] hub 4-0:1.0: usb_probe_interface
[    3.690033] hub 4-0:1.0: usb_probe_interface - got id
[    3.690035] hub 4-0:1.0: USB hub found
[    3.690048] hub 4-0:1.0: 5 ports detected
[    3.690091] hub 4-0:1.0: standalone hub
[    3.690093] hub 4-0:1.0: no power switching (usb 1.0)
[    3.690094] hub 4-0:1.0: no over-current protection
[    3.690096] hub 4-0:1.0: power on to power good time: 4ms
[    3.690102] hub 4-0:1.0: local power source is good
[    3.690104] hub 4-0:1.0: trying to enable port power on non-switchable hub
[    3.690131] drivers/usb/core/inode.c: creating file '001'
[    3.690172] ehci_hcd 0000:00:12.2: HS companion for 0000:00:12.0
[    3.690931] xen: registering gsi 18 triggering 0 polarity 1
[    3.690942] xen_map_pirq_gsi: returning irq 18 for gsi 18
[    3.690944] xen: --> pirq=18 -> irq=18 (gsi=18)
[    3.690946] Already setup the GSI :18
[    3.690950] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    3.690987] ohci_hcd 0000:00:13.0: OHCI Host Controller
[    3.690996] drivers/usb/core/inode.c: creating file '005'
[    3.692036] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[    3.692112] ohci_hcd 0000:00:13.0: enabled AMD prefetch quirk
[    3.692567] ohci_hcd 0000:00:13.0: created debug files
[    3.692574] ohci_hcd 0000:00:13.0: supports USB remote wakeup
[    3.692606] ohci_hcd 0000:00:13.0: irq 18, io mem 0xf98fc000
[    3.724236] ehci_hcd 0000:00:16.2: GetStatus port:3 status 001403 0  ACK POWER sig=k CSC CONNECT
[    3.724240] hub 3-0:1.0: port 3: status 0501 change 0001
[    3.747644] ohci_hcd 0000:00:13.0: OHCI controller state
[    3.747650] ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
[    3.747654] ohci_hcd 0000:00:13.0: control 0x283 RWC HCFS=operational CBSR=3
[    3.747657] ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
[    3.747661] ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
[    3.747664] ohci_hcd 0000:00:13.0: intrenable 0x8000005a MIE RHSC UE RD WDH
[    3.747674] ohci_hcd 0000:00:13.0: hcca frame #0005
[    3.747678] ohci_hcd 0000:00:13.0: roothub.a 02001205 POTPGT=2 NOCP NPS NDP=5(5)
[    3.747681] ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
[    3.747685] ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
[    3.747689] ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
[    3.747692] ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00000100 PPS
[    3.747696] ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
[    3.747699] ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000100 PPS
[    3.747703] ohci_hcd 0000:00:13.0: roothub.portstatus [4] 0x00000100 PPS
[    3.747720] usb usb5: default language 0x0409
[    3.747725] usb usb5: udev 1, busnum 5, minor = 512
[    3.747727] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    3.747729] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.747730] usb usb5: Product: OHCI Host Controller
[    3.747732] usb usb5: Manufacturer: Linux 3.1.0konrad-next-20111022+ ohci_hcd
[    3.747734] usb usb5: SerialNumber: 0000:00:13.0
[    3.749642] usb usb5: usb_probe_device
[    3.749647] usb usb5: configuration #1 chosen from 1 choice
[    3.749657] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[    3.750931] hub 5-0:1.0: usb_probe_interface
[    3.750935] hub 5-0:1.0: usb_probe_interface - got id
[    3.750937] hub 5-0:1.0: USB hub found
[    3.750948] hub 5-0:1.0: 5 ports detected
[    3.750950] hub 5-0:1.0: standalone hub
[    3.750951] hub 5-0:1.0: no power switching (usb 1.0)
[    3.750952] hub 5-0:1.0: no over-current protection
[    3.750954] hub 5-0:1.0: power on to power good time: 4ms
[    3.750958] hub 5-0:1.0: local power source is good
[    3.750961] hub 5-0:1.0: trying to enable port power on non-switchable hub
[    3.750986] drivers/usb/core/inode.c: creating file '001'
[    3.751018] ehci_hcd 0000:00:13.2: HS companion for 0000:00:13.0
[    3.751774] xen: registering gsi 18 triggering 0 polarity 1
[    3.751785] xen_map_pirq_gsi: returning irq 18 for gsi 18
[    3.751787] xen: --> pirq=18 -> irq=18 (gsi=18)
[    3.751789] Already setup the GSI :18
[    3.751793] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    3.751835] ohci_hcd 0000:00:14.5: OHCI Host Controller
[    3.751844] drivers/usb/core/inode.c: creating file '006'
[    3.753513] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 6
[    3.753530] ohci_hcd 0000:00:14.5: enabled AMD prefetch quirk
[    3.754062] ohci_hcd 0000:00:14.5: created debug files
[    3.754064] ohci_hcd 0000:00:14.5: supports USB remote wakeup
[    3.754073] ohci_hcd 0000:00:14.5: irq 18, io mem 0xf98fd000
[    3.809281] ohci_hcd 0000:00:14.5: OHCI controller state
[    3.809289] ohci_hcd 0000:00:14.5: OHCI 1.0, NO legacy support registers
[    3.809293] ohci_hcd 0000:00:14.5: control 0x283 RWC HCFS=operational CBSR=3
[    3.809297] ohci_hcd 0000:00:14.5: cmdstatus 0x00000 SOC=0
[    3.809300] ohci_hcd 0000:00:14.5: intrstatus 0x00000004 SF
[    3.809304] ohci_hcd 0000:00:14.5: intrenable 0x8000005a MIE RHSC UE RD WDH
[    3.809315] ohci_hcd 0000:00:14.5: hcca frame #0005
[    3.809318] ohci_hcd 0000:00:14.5: roothub.a 02001202 POTPGT=2 NOCP NPS NDP=2(2)
[    3.809322] ohci_hcd 0000:00:14.5: roothub.b 00000000 PPCM=0000 DR=0000
[    3.809325] ohci_hcd 0000:00:14.5: roothub.status 00008000 DRWE
[    3.809329] ohci_hcd 0000:00:14.5: roothub.portstatus [0] 0x00000100 PPS
[    3.809333] ohci_hcd 0000:00:14.5: roothub.portstatus [1] 0x00000100 PPS
[    3.809356] usb usb6: default language 0x0409
[    3.809362] usb usb6: udev 1, busnum 6, minor = 640
[    3.809363] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    3.809365] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.809367] usb usb6: Product: OHCI Host Controller
[    3.809369] usb usb6: Manufacturer: Linux 3.1.0konrad-next-20111022+ ohci_hcd
[    3.809371] usb usb6: SerialNumber: 0000:00:14.5
[    3.811267] usb usb6: usb_probe_device
[    3.811272] usb usb6: configuration #1 chosen from 1 choice
[    3.811282] usb usb6: adding 6-0:1.0 (config #1, interface 0)
[    3.812603] hub 6-0:1.0: usb_probe_interface
[    3.812608] hub 6-0:1.0: usb_probe_interface - got id
[    3.812610] hub 6-0:1.0: USB hub found
[    3.812625] hub 6-0:1.0: 2 ports detected
[    3.812626] hub 6-0:1.0: standalone hub
[    3.812627] hub 6-0:1.0: no power switching (usb 1.0)
[    3.812629] hub 6-0:1.0: no over-current protection
[    3.812630] hub 6-0:1.0: power on to power good time: 4ms
[    3.812635] hub 6-0:1.0: local power source is good
[    3.812637] hub 6-0:1.0: trying to enable port power on non-switchable hub
[    3.812657] drivers/usb/core/inode.c: creating file '001'
[    3.813988] xen: registering gsi 18 triggering 0 polarity 1
[    3.813997] xen_map_pirq_gsi: returning irq 18 for gsi 18
[    3.813999] xen: --> pirq=18 -> irq=18 (gsi=18)
[    3.814001] Already setup the GSI :18
[    3.814004] ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    3.814036] ohci_hcd 0000:00:16.0: OHCI Host Controller
[    3.814041] drivers/usb/core/inode.c: creating file '007'
[    3.815318] ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 7
[    3.815333] ohci_hcd 0000:00:16.0: enabled AMD prefetch quirk
[    3.815862] ohci_hcd 0000:00:16.0: created debug files
[    3.815864] ohci_hcd 0000:00:16.0: supports USB remote wakeup
[    3.815874] ohci_hcd 0000:00:16.0: irq 18, io mem 0xf98fe000
[    3.870727] ohci_hcd 0000:00:16.0: OHCI controller state
[    3.870735] ohci_hcd 0000:00:16.0: OHCI 1.0, NO legacy support registers
[    3.870739] ohci_hcd 0000:00:16.0: control 0x283 RWC HCFS=operational CBSR=3
[    3.870743] ohci_hcd 0000:00:16.0: cmdstatus 0x00000 SOC=0
[    3.870746] ohci_hcd 0000:00:16.0: intrstatus 0x00000004 SF
[    3.870750] ohci_hcd 0000:00:16.0: intrenable 0x8000005a MIE RHSC UE RD WDH
[    3.870760] ohci_hcd 0000:00:16.0: hcca frame #0005
[    3.870764] ohci_hcd 0000:00:16.0: roothub.a 02001204 POTPGT=2 NOCP NPS NDP=4(4)
[    3.870767] ohci_hcd 0000:00:16.0: roothub.b 00000000 PPCM=0000 DR=0000
[    3.870771] ohci_hcd 0000:00:16.0: roothub.status 00008000 DRWE
[    3.870774] ohci_hcd 0000:00:16.0: roothub.portstatus [0] 0x00000100 PPS
[    3.870778] ohci_hcd 0000:00:16.0: roothub.portstatus [1] 0x00000100 PPS
[    3.870781] ohci_hcd 0000:00:16.0: roothub.portstatus [2] 0x00000100 PPS
[    3.870785] ohci_hcd 0000:00:16.0: roothub.portstatus [3] 0x00000100 PPS
[    3.870801] usb usb7: default language 0x0409
[    3.870808] usb usb7: udev 1, busnum 7, minor = 768
[    3.870810] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    3.870811] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.870813] usb usb7: Product: OHCI Host Controller
[    3.870815] usb usb7: Manufacturer: Linux 3.1.0konrad-next-20111022+ ohci_hcd
[    3.870817] usb usb7: SerialNumber: 0000:00:16.0
[    3.872169] usb usb7: usb_probe_device
[    3.872174] usb usb7: configuration #1 chosen from 1 choice
[    3.872189] usb usb7: adding 7-0:1.0 (config #1, interface 0)
[    3.873487] hub 7-0:1.0: usb_probe_interface
[    3.873491] hub 7-0:1.0: usb_probe_interface - got id
[    3.873493] hub 7-0:1.0: USB hub found
[    3.873507] hub 7-0:1.0: 4 ports detected
[    3.873509] hub 7-0:1.0: standalone hub
[    3.873510] hub 7-0:1.0: no power switching (usb 1.0)
[    3.873511] hub 7-0:1.0: no over-current protection
[    3.873513] hub 7-0:1.0: power on to power good time: 4ms
[    3.873518] hub 7-0:1.0: local power source is good
[    3.873520] hub 7-0:1.0: trying to enable port power on non-switchable hub
[    3.873546] drivers/usb/core/inode.c: creating file '001'
[    3.873583] ehci_hcd 0000:00:16.2: HS companion for 0000:00:16.0
[    3.874906] initcall ohci_hcd_mod_init+0x0/0xbf returned 0 after 241499 usecs
[    3.874910] calling  uhci_hcd_init+0x0/0x122 @ 1
[    3.874912] uhci_hcd: USB Universal Host Controller Interface driver
[    3.876259] initcall uhci_hcd_init+0x0/0x122 returned 0 after 1308 usecs
[    3.876262] calling  usblp_init+0x0/0x1b @ 1
[    3.877189] usbcore: registered new interface driver usblp
[    3.877206] initcall usblp_init+0x0/0x1b returned 0 after 911 usecs
[    3.877215] calling  usb_stor_init+0x0/0x50 @ 1
[    3.877220] Initializing USB Mass Storage driver...
[    3.878791] usbcore: registered new interface driver usb-storage
[    3.878794] USB Mass Storage support registered.
[    3.878799] initcall usb_stor_init+0x0/0x50 returned 0 after 1538 usecs
[    3.878802] calling  usb_usual_init+0x0/0x3e @ 1
[    3.880143] usbcore: registered new interface driver libusual
[    3.880150] initcall usb_usual_init+0x0/0x3e returned 0 after 1311 usecs
[    3.880153] calling  usb_serial_init+0x0/0x237 @ 1
[    3.882248] usbcore: registered new interface driver usbserial
[    3.882252] usbserial: USB Serial Driver core
[    3.882258] initcall usb_serial_init+0x0/0x237 returned 0 after 2050 usecs
[    3.882261] calling  cp210x_init+0x0/0x59 @ 1
[    3.883599] USB Serial support registered for cp210x
[    3.885415] usbcore: registered new interface driver cp210x
[    3.885419] cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
[    3.885425] initcall cp210x_init+0x0/0x59 returned 0 after 3084 usecs
[    3.885428] calling  cypress_init+0x0/0xb9 @ 1
[    3.886706] USB Serial support registered for DeLorme Earthmate USB
[    3.887971] USB Serial support registered for HID->COM RS232 Adapter
[    3.889193] USB Serial support registered for Nokia CA-42 V2 Adapter
[    3.890138] usbcore: registered new interface driver cypress
[    3.890147] cypress_m8: v1.10:Cypress USB to Serial Driver
[    3.890161] initcall cypress_init+0x0/0xb9 returned 0 after 4611 usecs
[    3.890170] calling  moschip7720_init+0x0/0x76 @ 1
[    3.891689] USB Serial support registered for Moschip 2 port adapter
[    3.891692] mos7720: 2.1:Moschip USB Serial Driver
[    3.892349] usbcore: registered new interface driver moschip7720
[    3.892357] initcall moschip7720_init+0x0/0x76 returned 0 after 2126 usecs
[    3.892360] calling  moschip7840_init+0x0/0xcc @ 1
[    3.894145] USB Serial support registered for Moschip 7840/7820 USB Serial Driver
[    3.894149] mos7840: 1.3.2:Moschip 7840/7820 USB Serial Driver
[    3.895396] usbcore: registered new interface driver mos7840
[    3.895406] initcall moschip7840_init+0x0/0xcc returned 0 after 2968 usecs
[    3.895408] calling  i8042_init+0x0/0x3ab @ 1
[    3.902280] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    3.904122] serio: i8042 KBD port at 0x60,0x64 irq 1
[    3.904133] serio: i8042 AUX port at 0x60,0x64 irq 12
[    3.906013] initcall i8042_init+0x0/0x3ab returned 0 after 10346 usecs
[    3.906017] calling  serport_init+0x0/0x34 @ 1
[    3.906020] initcall serport_init+0x0/0x34 returned 0 after 0 usecs
[    3.906022] calling  mousedev_init+0x0/0x61 @ 1
[    3.907367] mousedev: PS/2 mouse device common for all mice
[    3.907376] initcall mousedev_init+0x0/0x61 returned 0 after 1316 usecs
[    3.907379] calling  evdev_init+0x0/0x12 @ 1
[    3.909973] initcall evdev_init+0x0/0x12 returned 0 after 2524 usecs
[    3.909976] calling  atkbd_init+0x0/0x27 @ 1
[    3.911319] initcall atkbd_init+0x0/0x27 returned 0 after 1302 usecs
[    3.911323] calling  psmouse_init+0x0/0x79 @ 1
[    3.914777] initcall psmouse_init+0x0/0x79 returned 0 after 3364 usecs
[    3.914780] calling  xenkbd_init+0x0/0x59 @ 1
[    3.914782] initcall xenkbd_init+0x0/0x59 returned -19 after 0 usecs
[    3.914784] calling  cmos_init+0x0/0x6a @ 1
[    3.914828] rtc_cmos 00:04: RTC can wake from S4
[    3.916305] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    3.916377] rtc0: alarms up to one month, y3k, 114 bytes nvram
[    3.917711] initcall cmos_init+0x0/0x6a returned 0 after 2849 usecs
[    3.917714] calling  i2c_i801_init+0x0/0xad @ 1
[    3.918990] initcall i2c_i801_init+0x0/0xad returned 0 after 1237 usecs
[    3.918994] calling  init_rc_map_adstech_dvb_t_pci+0x0/0x12 @ 1
[    3.918997] initcall init_rc_map_adstech_dvb_t_pci+0x0/0x12 returned 0 after 0 usecs
[    3.918999] calling  init_rc_map_alink_dtu_m+0x0/0x12 @ 1
[    3.919041] initcall init_rc_map_alink_dtu_m+0x0/0x12 returned 0 after 0 usecs
[    3.919043] calling  init_rc_map_anysee+0x0/0x12 @ 1
[    3.919045] initcall init_rc_map_anysee+0x0/0x12 returned 0 after 0 usecs
[    3.919047] calling  init_rc_map_apac_viewcomp+0x0/0x12 @ 1
[    3.919050] initcall init_rc_map_apac_viewcomp+0x0/0x12 returned 0 after 0 usecs
[    3.919061] calling  init_rc_map_asus_pc39+0x0/0x12 @ 1
[    3.919063] initcall init_rc_map_asus_pc39+0x0/0x12 returned 0 after 0 usecs
[    3.919065] calling  init_rc_map_ati_tv_wonder_hd_600+0x0/0x12 @ 1
[    3.919067] initcall init_rc_map_ati_tv_wonder_hd_600+0x0/0x12 returned 0 after 0 usecs
[    3.919070] calling  init_rc_map_avermedia_a16d+0x0/0x12 @ 1
[    3.919072] initcall init_rc_map_avermedia_a16d+0x0/0x12 returned 0 after 0 usecs
[    3.919074] calling  init_rc_map_avermedia+0x0/0x12 @ 1
[    3.919077] initcall init_rc_map_avermedia+0x0/0x12 returned 0 after 0 usecs
[    3.919079] calling  init_rc_map_avermedia_cardbus+0x0/0x12 @ 1
[    3.919081] initcall init_rc_map_avermedia_cardbus+0x0/0x12 returned 0 after 0 usecs
[    3.919083] calling  init_rc_map_avermedia_dvbt+0x0/0x12 @ 1
[    3.919085] initcall init_rc_map_avermedia_dvbt+0x0/0x12 returned 0 after 0 usecs
[    3.919087] calling  init_rc_map_avermedia_m135a+0x0/0x12 @ 1
[    3.919090] initcall init_rc_map_avermedia_m135a+0x0/0x12 returned 0 after 0 usecs
[    3.919092] calling  init_rc_map_avermedia_m733a_rm_k6+0x0/0x12 @ 1
[    3.919094] initcall init_rc_map_avermedia_m733a_rm_k6+0x0/0x12 returned 0 after 0 usecs
[    3.919096] calling  init_rc_map_avermedia_rm_ks+0x0/0x12 @ 1
[    3.919099] initcall init_rc_map_avermedia_rm_ks+0x0/0x12 returned 0 after 0 usecs
[    3.919101] calling  init_rc_map_avertv_303+0x0/0x12 @ 1
[    3.919103] initcall init_rc_map_avertv_303+0x0/0x12 returned 0 after 0 usecs
[    3.919105] calling  init_rc_map_azurewave_ad_tu700+0x0/0x12 @ 1
[    3.919107] initcmap_azurewave_ad_tu700+0x0/0x12 returned 0 after 0 usecs
[    3.919109] calling  init_rc_map_behold+0x0/0x12 @ 1
[    3.919112] initcall init_rc_map_behold+0x0/0x12 returned 0 after 0 usecs
[    3.919114] calling  init_rc_map_behold_columbus+0x0/0x12 @ 1
[    3.919116] initcall init_rc_map_behold_columbus+0x0/0x12 returned 0 after 0 usecs
[    3.919118] calling  init_rc_map_budget_ci_old+0x0/0x12 @ 1
[    3.919120] initcall init_rc_map_budget_ci_old+0x0/0x12 returned 0 after 0 usecs
[    3.919122] calling  init_rc_map_cinergy_1400+0x0/0x12 @ 1
[    3.919125] initcall init_rc_map_cinergy_1400+0x0/0x12 returned 0 after 0 usecs
[    3.919127] calling  init_rc_map_cinergy+0x0/0x12 @ 1
[    3.919129] initcall init_rc_map_cinergy+0x0/0x12 returned 0 after 0 usecs
[    3.919131] calling  init_rc_map+0x0/0x12 @ 1
[    3.919133] initcall init_rc_map+0x0/0x12 returned 0 after 0 usecs
[    3.919135] calling  init_rc_map+0x0/0x12 @ 1
[    3.919137] initcall init_rc_map+0x0/0x12 returned 0 after 0 usecs
[    3.919139] calling  init_rc_map_digitalnow_tinytwin+0x0/0x12 @ 1
[    3.919141] initcall init_rc_map_digitalnow_tinytwin+0x0/0x12 returned 0 after 0 usecs
[    3.919144] calling  init_rc_map_digittrade+0x0/0x12 @ 1
[    3.919146] initcall init_rc_map_digittrade+0x0/0x12 returned 0 after 0 usecs
[    3.919148] calling  init_rc_map_dm1105_nec+0x0/0x12 @ 1
[    3.919150] initcall init_rc_map_dm1105_nec+0x0/0x12 returned 0 after 0 usecs
[    3.919153] calling  init_rc_map_dntv_live_dvb_t+0x0/0x12 @ 1
[    3.919155] initcall init_rc_map_dntv_live_dvb_t+0x0/0x12 returned 0 after 0 usecs
[    3.919157] calling  init_rc_map_dntv_live_dvbt_pro+0x0/0x12 @ 1
[    3.919159] initcall init_rc_map_dntv_live_dvbt_pro+0x0/0x12 returned 0 after 0 usecs
[    3.919162] calling  init_rc_map_em_terratec+0x0/0x12 @ 1
[    3.919164] initcall init_rc_map_em_terratec+0x0/0x12 returned 0 after 0 usecs
[    3.919166] calling  init_rc_map_encore_enltv2+0x0/0x12 @ 1
[    3.919168] initcall init_rc_map_encore_enltv2+0x0/0x12 returned 0 after 0 usecs
[    3.919170] calling  init_rc_map_encore_enltv+0x0/0x12 @ 1
[    3.919172] initcall init_rc_map_encore_enltv+0x0/0x12 returned 0 after 0 usecs
[    3.919175] calling  init_rc_map_encore_enltv_fm53+0x0/0x12 @ 1
[    3.919177] initcall init_rc_map_encore_enltv_fm53+0x0/0x12 returned 0 after 0 usecs
[    3.919179] calling  init_rc_map_evga_indtube+0x0/0x12 @ 1
[    3.919181] initcall init_rc_map_evga_indtube+0x0/0x12 returned 0 after 0 usecs
[    3.919183] calling  init_rc_map_eztv+0x0/0x12 @ 1
[    3.919185] initcall init_rc_map_eztv+0x0/0x12 returned 0 after 0 usecs
[    3.919187] calling  init_rc_map_flydvb+0x0/0x12 @ 1
[    3.919190] initcall init_rc_map_flydvb+0x0/0x12 returned 0 after 0 usecs
[    3.919192] calling  init_rc_map_flyvideo+0x0/0x12 @ 1
[    3.919194] initcall init_rc_map_flyvideo+0x0/0x12 returned 0 after 0 usecs
[    3.919196] calling  init_rc_map_fusionhdtv_mce+0x0/0x12 @ 1
[    3.919198] initcall init_rc_map_fusionhdtv_mce+0x0/0x12 returned 0 after 0 usecs
[    3.919200] calling  init_rc_map_gadmei_rm008z+0x0/0x12 @ 1
[    3.919203] initcall init_rc_map_gadmei_rm008z+0x0/0x12 returned 0 after 0 usecs
[    3.919205] calling  init_rc_map_genius_tvgo_a11mce+0x0/0x12 @ 1
[    3.919207] initcall init_rc_map_genius_tvgo_a11mce+0x0/0x12 returned 0 after 0 usecs
[    3.919209] calling  init_rc_map_gotview7135+0x0/0x12 @ 1
[    3.919212] initcall init_rc_map_gotview7135+0x0/0x12 returned 0 after 0 usecs
[    3.919214] calling  init_rc_map_imon_mce+0x0/0x12 @ 1
[    3.919216] initcall init_rc_map_imon_mce+0x0/0x12 returned 0 after 0 usecs
[    3.919218] calling  init_rc_map_imon_pad+0x0/0x12 @ 1
[    3.919220] initcall init_rc_map_imon_pad+0x0/0x12 returned 0 after 0 usecs
[    3.919222] calling  init_rc_map_iodata_bctv7e+0x0/0x12 @ 1
[    3.919224] initcall init_rc_map_iodata_bctv7e+0x0/0x12 returned 0 after 0 usecs
[    3.919227] calling  init_rc_map_kaiomy+0x0/0x12 @ 1
[    3.919229] initcall init_rc_map_kaiomy+0x0/0x12 returned 0 after 0 usecs
[    3.919231] calling  init_rc_map_kworld_315u+0x0/0x12 @ 1
[    3.919233] initcall init_rc_map_kworld_315u+0x0/0x12 returned 0 after 0 usecs
[    3.919235] calling  init_rc_map_kworld_plus_tv_analog+0x0/0x12 @ 1
[    3.919238] initcall init_rc_map_kworld_plus_tv_analog+0x0/0x12 returned 0 after 0 usecs
[    3.919240] calling  init_rc_map_leadtek_y04g0051+0x0/0x12 @ 1
[    3.919242] initcall init_rc_map_leadtek_y04g0051+0x0/0x12 returned 0 after 0 usecs
[    3.919245] calling  init_rc_map_lirc+0x0/0x12 @ 1
[    3.919247] initcall init_rc_map_lirc+0x0/0x12 returned 0 after 0 usecs
[    3.919249] calling  init_rc_lme2510_map+0x0/0x12 @ 1
[    3.919251] initcall init_rc_lme2510_map+0x0/0x12 returned 0 after 0 usecs
[    3.919253] calling  init_rc_map_manli+0x0/0x12 @ 1
[    3.919255] initcall init_rc_map_manli+0x0/0x12 returned 0 after 0 usecs
[    3.919258] calling  init_rc_map_msi_digivox_ii+0x0/0x12 @ 1
[    3.919260] initcall init_rc_map_msi_digivox_ii+0x0/0x12 returned 0 after 0 usecs
[    3.919262] calling  init_rc_map_msi_digivox_iii+0x0/0x12 @ 1
[    3.919264] initcall init_rc_map_msi_digivox_iii+0x0/0x12 returned 0 after 0 usecs
[    3.919267] calling  init_rc_map_msi_tvanywhere+0x0/0x12 @ 1
[    3.919269] initcall init_rc_map_msi_tvanywhere+0x0/0x12 returned 0 after 0 usecs
[    3.919271] calling  init_rc_map_msi_tvanywhere_plus+0x0/0x12 @ 1
[    3.919274] initcall init_rc_map_msi_tvanywhere_plus+0x0/0x12 returned 0 after 0 usecs
[    3.919276] calling  init_rc_map_nebula+0x0/0x12 @ 1
[    3.919279] initcall init_rc_map_nebula+0x0/0x12 returned 0 after 0 usecs
[    3.919281] calling  init_rc_map_nec_terratec_cinergy_xs+0x0/0x12 @ 1
[    3.919284] initcall init_rc_map_nec_terratec_cinergy_xs+0x0/0x12 returned 0 after 0 usecs
[    3.919286] calling  init_rc_map_norwood+0x0/0x12 @ 1
[    3.919289] initcall init_rc_map_norwood+0x0/0x12 returned 0 after 0 usecs
[    3.919291] calling  init_rc_map_npgtech+0x0/0x12 @ 1
[    3.919293] initcall init_rc_map_npgtech+0x0/0x12 returned 0 after 0 usecs
[    3.919295] calling  init_rc_map_pctv_sedna+0x0/0x12 @ 1
[    3.919298] initcall init_rc_map_pctv_sedna+0x0/0x12 returned 0 after 0 usecs
[    3.919300] calling  init_rc_map_pinnacle_color+0x0/0x12 @ 1
[    3.919302] initcall init_rc_map_pinnacle_color+0x0/0x12 returned 0 after 0 usecs
[    3.919305] calling  init_rc_map_pinnacle_grey+0x0/0x12 @ 1
[    3.919307] initcall init_rc_map_pinnacle_grey+0x0/0x12 returned 0 after 0 usecs
[    3.919309] calling  init_rc_map_pinnacle_pctv_hd+0x0/0x12 @ 1
[    3.919312] initcall init_rc_map_pinnacle_pctv_hd+0x0/0x12 returned 0 after 0 usecs
[    3.919314] calling  init_rc_map_pixelview+0x0/0x12 @ 1
[    3.919316] initcall init_rc_map_pixelview+0x0/0x12 returned 0 after 0 usecs
[    3.919318] calling  init_rc_map_pixelview+0x0/0x12 @ 1
[    3.919321] initcall init_rc_map_pixelview+0x0/0x12 returned 0 after 0 usecs
[    3.919323] calling  init_rc_map_pixelview+0x0/0x12 @ 1
[    3.919325] initcall init_rc_map_pixelview+0x0/0x12 returned 0 after 0 usecs
[    3.919327] calling  init_rc_map_pixelview_new+0x0/0x12 @ 1
[    3.919330] initcall init_rc_map_pixelview_new+0x0/0x12 returned 0 after 0 usecs
[    3.919332] calling  init_rc_map_powercolor_real_angel+0x0/0x12 @ 1
[    3.919334] initcall init_rc_map_powercolor_real_angel+0x0/0x12 returned 0 after 0 usecs
[    3.919337] calling  init_rc_map_proteus_2309+0x0/0x12 @ 1
[    3.919339] initcall init_rc_map_proteus_2309+0x0/0x12 returned 0 after 0 usecs
[    3.919341] calling  init_rc_map_purpletv+0x0/0x12 @ 1
[    3.919343] initcall init_rc_map_purpletv+0x0/0x12 returned 0 after 0 usecs
[    3.919345] calling  init_rc_map_pv951+0x0/0x12 @ 1
[    3.919348] initcall init_rc_map_pv951+0x0/0x12 returned 0 after 0 usecs
[    3.919350] calling  init_rc_map_rc5_hauppauge_new+0x0/0x12 @ 1
[    3.919352] initcall init_rc_map_rc5_hauppauge_new+0x0/0x12 returned 0 after 0 usecs
[    3.919354] calling  init_rc_map_rc6_mce+0x0/0x12 @ 1
[    3.919357] initcall init_rc_map_rc6_mce+0x0/0x12 returned 0 after 0 usecs
[    3.919359] calling  init_rc_map_real_audio_220_32_keys+0x0/0x12 @ 1
[    3.919361] initcall init_rc_map_real_audio_220_32_keys+0x0/0x12 returned 0 after 0 usecs
[    3.919364] calling  init_rc_map_streamzap+0x0/0x12 @ 1
[    3.919366] initcall init_rc_map_streamzap+0x0/0x12 returned 0 after 0 usecs
[    3.919368] calling  init_rc_map_tbs_nec+0x0/0x12 @ 1
[    3.919370] initcall init_rc_map_tbs_nec+0x0/0x12 returned 0 after 0 usecs
[    3.919372] calling  init_rc_map+0x0/0x12 @ 1
[    3.919375] initcall init_rc_map+0x0/0x12 returned 0 after 0 usecs
[    3.919377] calling  init_rc_map_terratec_cinergy_xs+0x0/0x12 @ 1
[    3.919379] initcall init_rc_map_terratec_cinergy_xs+0x0/0x12 returned 0 after 0 usecs
[    3.919381] calling  init_rc_map_terratec_slim+0x0/0x12 @ 1
[    3.919383] initcall init_rc_map_terratec_slim+0x0/0x12 returned 0 after 0 usecs
[    3.919385] calling  init_rc_map_terratec_slim_2+0x0/0x12 @ 1
[    3.919387] initcall init_rc_map_terratec_slim_2+0x0/0x12 returned 0 after 0 usecs
[    3.919388] calling  init_rc_map_tevii_nec+0x0/0x12 @ 1
[    3.919390] initcall init_rc_map_tevii_nec+0x0/0x12 returned 0 after 0 usecs
[    3.919392] calling  init_rc_map_tivo+0x0/0x12 @ 1
[    3.919393] initcall init_rc_map_tivo+0x0/0x12 returned 0 after 0 usecs
[    3.919395] calling  init_rc_map_total_media_in_hand+0x0/0x12 @ 1
[    3.919397] initcall init_rc_map_total_media_in_hand+0x0/0x12 returned 0 after 0 usecs
[    3.919399] calling  init_rc_map_trekstor+0x0/0x12 @ 1
[    3.919401] initcall init_rc_map_trekstor+0x0/0x12 returned 0 after 0 usecs
[    3.919402] calling  init_rc_map_tt_1500+0x0/0x12 @ 1
[    3.919404] initcall init_rc_map_tt_1500+0x0/0x12 returned 0 after 0 usecs
[    3.919406] calling  init_rc_map_twinhan_vp1027+0x0/0x12 @ 1
[    3.919408] initcall init_rc_map_twinhan_vp1027+0x0/0x12 returned 0 after 0 usecs
[    3.919410] calling  init_rc_map_videomate_m1f+0x0/0x12 @ 1
[    3.919411] initcall init_rc_map_videomate_m1f+0x0/0x12 returned 0 after 0 usecs
[    3.919413] calling  init_rc_map_videomate_s350+0x0/0x12 @ 1
[    3.919415] initcall init_rc_map_videomate_s350+0x0/0x12 returned 0 after 0 usecs
[    3.919417] calling  init_rc_map_videomate_tv_pvr+0x0/0x12 @ 1
[    3.919419] initcall init_rc_map_videomate_tv_pvr+0x0/0x12 returned 0 after 0 usecs
[    3.919421] calling  init_rc_map_winfast+0x0/0x12 @ 1
[    3.919422] initcall init_rc_map_winfast+0x0/0x12 returned 0 after 0 usecs
[    3.919424] calling  init_rc_map_winfast_usbii_deluxe+0x0/0x12 @ 1
[    3.919426] initcall init_rc_map_winfast_usbii_deluxe+0x0/0x12 returned 0 after 0 usecs
[    3.919428] calling  rc_core_init+0x0/0x49 @ 1
[    3.920717] initcall rc_core_init+0x0/0x49 returned 0 after 1250 usecs
[    3.920720] calling  lirc_dev_init+0x0/0x98 @ 1
[    3.922001] lirc_dev: IR Remote Control driver registered, major 251 
[    3.922008] initcall lirc_dev_init+0x0/0x98 returned 0 after 1253 usecs
[    3.922011] calling  ir_nec_decode_init+0x0/0x22 @ 1
[    3.922012] IR NEC protocol handler initialized
[    3.922014] initcall ir_nec_decode_init+0x0/0x22 returned 0 after 1 usecs
[    3.922016] calling  ir_rc5_decode_init+0x0/0x22 @ 1
[    3.922018] IR RC5(x) protocol handler initialized
[    3.922019] initcall ir_rc5_decode_init+0x0/0x22 returned 0 after 1 usecs
[    3.922021] calling  ir_rc6_decode_init+0x0/0x22 @ 1
[    3.922023] IR RC6 protocol handler initialized
[    3.922024] initcall ir_rc6_decode_init+0x0/0x22 returned 0 after 1 usecs
[    3.922026] calling  ir_jvc_decode_init+0x0/0x22 @ 1
[    3.922027] IR JVC protocol handler initialized
[    3.922029] initcall ir_jvc_decode_init+0x0/0x22 returned 0 after 1 usecs
[    3.922031] calling  ir_sony_decode_init+0x0/0x22 @ 1
[    3.922032] IR Sony protocol handler initialized
[    3.922034] initcall ir_sony_decode_init+0x0/0x22 returned 0 after 1 usecs
[    3.922036] calling  ir_rc5_sz_decode_init+0x0/0x22 @ 1
[    3.922037] IR RC5 (streamzap) protocol handler initialized
[    3.922039] initcall ir_rc5_sz_decode_init+0x0/0x22 returned 0 after 1 usecs
[    3.922041] calling  ir_mce_kbd_decode_init+0x02042] IR MCE Keyboard/mouse protocol handler initialized
[    3.922044] initcall ir_mce_kbd_decode_init+0x0/0x22 returned3.922046] calling  ir_lirc_codec_init+0x0/0x22 @ 1
[  R LIRC bridge handler initialized
[    3.922049] _init+0x0/0x22 returned 0 after 1 usecs
[    3.92207dev_init+0x0/0x89 @ 1
[    3.922079] Linux video capture interface: v2.00
[    3.922816] initcall videodev_init+0x0/0x89 returned 0 after 713 usecs
[    3.922819] calling  init_tuner+0x0/0x14 @ 1
[    3.924773] i2c-core: driver [tuner] using legacy suspend method
[    3.924775] i2c-core: driver [tuner] using legacy resume method
[    3.924782] initcall init_tuner+0x0/0x14 returned 0 after 1911 usecs
[    3.924784] calling  init_saa711x+0x0/0x14 @ 1
[    3.925994] initcall init_saa711x+0x0/0x14 returned 0 after 1173 usecs
[    3.925998] calling  init_tvp5150+0x0/0x14 @ 1
[    3.927249] initcall init_tvp5150+0x0/0x14 returned 0 after 1213 usecs
[    3.927253] calling  init_msp+0x0/0x14 @ 1
[    3.928557] i2c-core: driver [msp3400] using legacy suspend method
[    3.928560] i2c-core: driver [msp3400] using legacy resume method
[    3.928566] initcall init_msp+0x0/0x14 returned 0 after 1278 usecs
[    3.928569] calling  init_cs53l32a+0x0/0x14 @ 1
[    3.929809] initcall init_cs53l32a+0x0/0x14 returned 0 after 1204 usecs
[    3.929813] calling  init_wm8775+0x0/0x14 @ 1
[    3.931033] initcall init_wm8775+0x0/0x14 returned 0 after 1183 usecs
[    3.931036] calling  init_cx25840+0x0/0x14 @ 1
[    3.932781] initcall init_cx25840+0x0/0x14 returned 0 after 1696 usecs
[    3.932784] calling  init_mt9v011+0x0/0x14 @ 1
[    3.933632] initcall init_mt9v011+0x0/0x14 returned 0 after 819 usecs
[    3.933635] calling  em28xx_module_init+0x0/0x48 @ 1
[    3.934885] usbcore: registered new interface driver em28xx
[    3.934888] em28xx driver loaded
[    3.934893] initcall em28xx_module_init+0x0/0x48 returned 0 after 1223 usecs
[    3.934896] calling  em28xx_alsa_register+0x0/0x12 @ 1
[    3.934898] Em28xx: Initialized (Em28xx Audio Extension) extension
[    3.934900] initcall em28xx_alsa_register+0x0/0x12 returned 0 after 1 usecs
[    3.934901] calling  cx231xx_module_init+0x0/0x48 @ 1
[    3.934903] cx231xx v4l2 driver loaded.
[    3.936169] usbcore: registered new interface driver cx231xx
[    3.936177] initcall cx231xx_module_init+0x0/0x48 returned 0 after 1239 usecs
[    3.936179] calling  usbvision_init+0x0/0x105 @ 1
[    3.938603] usbcore: registered new interface driver usbvision
[    3.938607] USBVision USB Video Device Driver for Linux : 0.9.11
[    3.938612] initcall usbvision_init+0x0/0x105 returned 0 after 2371 usecs
[    3.938615] calling  pvr_init+0x0/0xb2 @ 1
[    3.943613] usbcore: registered new interface driver pvrusb2
[    3.943617] pvrusb2: V4L in-tree version:Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner
[    3.943618] pvrusb2: Debug mask is 31 (0x1f)
[    3.943623] initcall pvr_init+0x0/0xb2 returned 0 after 4886 usecs
[    3.943626] calling  zr364xx_init+0x0/0x49 @ 1
[    3.944853] usbcore: registered new interface driver zr364xx
[    3.944857] zr364xx: Zoran 364xx
[    3.944863] initcall zr364xx_init+0x0/0x49 returned 0 after 1202 usecs
[    3.944865] calling  stk_camera_init+0x0/0x3a @ 1
[    3.946317] usbcore: registered new interface driver stkwebcam
[    3.946325] initcall stk_camera_init+0x0/0x3a returned 0 after 1419 usecs
[    3.946327] calling  sn9c102_module_init+0x0/0x5b @ 1
[    3.946329] sn9c102: V4L2 driver for SN9C1xx PC Camera Controllers v1:1.48
[    3.948608] usbcore: registered new interface driver sn9c102
[    3.948616] initcall sn9c102_module_init+0x0/0x5b returned 0 after 2229 usecs
[    3.948618] calling  et61x251_module_init+0x0/0x5a @ 1
[    3.948620] et61x251: V4L2 driver for ET61X[12]51 PC Camera Controllers v1.1.10
[    3.951034] usbcore: registered new interface driver et61x251
[    3.951041] initcall et61x251_module_init+0x0/0x5a returned 0 after 2360 usecs
[    3.951044] calling  usb_pwc_init+0x0/0x20a @ 1
[    3.953182] usbcore: registered new interface driver Philips webcam
[    3.953189] initcall usb_pwc_init+0x0/0x20a returned 0 after 2090 usecs
[    3.953192] calling  gspca_init+0x0/0x16 @ 1
[    3.953193] gspca: v2.13.0 registered
[    3.953195] initcall gspca_init+0x0/0x16 returned 0 after 1 usecs
[    3.953196] calling  hdpvr_init+0x0/0x3a @ 1
[    3.954601] usbcore: registered new interface driver hdpvr
[    3.954609] initcall hdpvr_init+0x0/0x3a returned 0 after 1373 usecs
[    3.954611] calling  usb_s2255_init+0x0/0x58 @ 1
[    3.956478] usbcore: registered new interface driver s2255
[    3.956485] initcall usb_s2255_init+0x0/0x58 returned 0 after 1825 usecs
[    3.956488] calling  ir_init+0x0/0x14 @ 1
[    3.957750] initcall ir_init+0x0/0x14 returned 0 after 1225 usecs
[    3.957753] calling  f71882fg_init+0x0/0x15a @ 1
[    3.957832] f71882fg: Found f71889ed chip at 0x600, revision 16
[    3.961753] f71882fg f71882fg.1536: Fan: 1 is in duty-cycle mode
[    3.961756] f71882fg f71882fg.1536: Fan: 2 is in duty-cycle mode
[    3.961757] f71882fg f71882fg.1536: Fan: 3 is in duty-cycle mode
[    3.963586] initcall f71882fg_init+0x0/0x15a returned 0 after 5687 usecs
[    3.963590] calling  fam15h_power_init+0x0/0x1b @ 1
[    3.965779] initcall fam15h_power_init+0x0/0x1b returned 0 after 2130 usecs
[    3.965782] calling  k8temp_init+0x0/0x1b @ 1
[    3.966482] initcall k8temp_init+0x0/0x1b returned 0 after 675 usecs
[    3.966486] calling  k10temp_init+0x0/0x1b @ 1
[    3.969253] initcall k10temp_init+0x0/0x1b returned 0 after 2693 usecs
[    3.969256] calling  f71808e_init+0x0/0x456 @ 1
[    3.969307] f71808e_wdt: Unrecognized Fintek device: 0909
[    3.969313] initcall f71808e_init+0x0/0x456 returned -19 after 52 usecs
[    3.969315] calling  sp5100_tco_init_module+0x0/0x9d @ 1
[    3.969317] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01
[    3.972000] SP5100 TCO timer: mmio address 0xb8fe00 already in use
[    3.972013] initcall sp5100_tco_init_module+0x0/0x9d returned 0 after 2628 usecs
[    3.972016] calling  xen_wdt_init_module+0x0/0xaf @ 1
[    3.972017] wdt: Xen WatchDog Timer Driver v0.01
[    3.975628] wdt: initialized (timeout=60s, nowayout=0)
[    3.975638] initcall xen_wdt_init_module+0x0/0xaf returned 0 after 3531 usecs
[    3.975641] calling  dm_init+0x0/0x48 @ 1
[    3.980151] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com
[    3.980159] initcall dm_init+0x0/0x48 returned 0 after 4406 usecs
[    3.980162] calling  dm_crypt_init+0x0/0x69 @ 1
[    3.981764] initcall dm_crypt_init+0x0/0x69 returned 0 after 1557 usecs
[    3.981767] calling  dm_snapshot_init+0x0/0x211 @ 1
[    3.983107] initcall dm_snapshot_init+0x0/0x211 returned 0 after 1299 usecs
[    3.983111] calling  dm_mirror_init+0x0/0x79 @ 1
[    3.984759] initcall dm_mirror_init+0x0/0x79 returned 0 after 1599 usecs
[    3.984763] calling  dm_dirty_log_init+0x0/0x59 @ 1
[    3.984765] initcall dm_dirty_log_init+0x0/0x59 returned 0 after 0 usecs
[    3.984767] calling  dm_zero_init+0x0/0x31 @ 1
[    3.984769] initcall dm_zero_init+0x0/0x31 returned 0 after 0 usecs
[    3.984771] calling  cpufreq_gov_dbs_init+0x0/0x5f @ 1
[    3.984775] initcall cpufreq_gov_dbs_init+0x0/0x5f returned 0 after 1 usecs
[    3.984777] calling  init_ladder+0x0/0x12 @ 1
[    3.984780] initcall init_ladder+0x0/0x12 returned -19 after 0 usecs
[    3.984782] calling  init_menu+0x0/0x12 @ 1
[    3.984784] initcall init_menu+0x0/0x12 returned -19 after 0 usecs
[    3.984786] calling  efivars_init+0x0/0xf7 @ 1
[    3.984787] EFI Variables Facility v0.08 2004-May-17
[    3.984790] initcall efivars_init+0x0/0xf7 returned 0 after 2 usecs
[    3.984792] calling  hid_init+0x0/0x66 @ 1
[    3.986808] initcall hid_init+0x0/0x66 returned 0 after 1961 usecs
[    3.986812] calling  a4_init+0x0/0x1b @ 1
[    3.988066] initcall a4_init+0x0/0x1b returned 0 after 1207 usecs
[    3.988070] calling  apple_init+0x0/0x39 @ 1
[    3.989402] initcall apple_init+0x0/0x39 returned 0 after 1292 usecs
[    3.989405] calling  belkin_init+0x0/0x1b @ 1
[    3.990720] initcall belkin_init+0x0/0x1b returned 0 after 1275 usecs
[    3.990723] calling  ch_init+0x0/0x1b @ 1
[    3.991998] initcall ch_init+0x0/0x1b returned 0 after 1199 usecs
[    3.992001] calling  ch_init+0x0/0x1b @ 1
[    3.993413] initcall ch_init+0x0/0x1b returned 0 after 1357 usecs
[    3.993417] calling  cp_init+0x0/0x1b @ 1
[    3.994681] initcall cp_init+0x0/0x1b returned 0 after 1226 usecs
[    3.994684] calling  ez_init+0x0/0x1b @ 1
[    3.996100] initcall ez_init+0x0/0x1b returned 0 after 1371 usecs
[    3.996104] calling  gyration_init+0x0/0x1b @ 1
[    3.998297] initcall gyration_init+0x0/0x1b returned 0 after 2132 usecs
[    3.998300] calling  ks_init+0x0/0x1b @ 1
[    3.999626] initcall ks_init+0x0/0x1b returned 0 after 1287 usecs
[    3.999629] calling  kye_init+0x0/0x1b @ 1
[    4.000867] initcall kye_init+0x0/0x1b returned 0 after 1200 usecs
[    4.000870] calling  lg_init+0x0/0x1b @ 1
[    4.001677] initcall lg_init+0x0/0x1b returned 0 after 778 usecs
[    4.001680] calling  ms_init+0x0/0x1b @ 1
[    4.002927] initcall ms_init+0x0/0x1b returned 0 after 1210 usecs
[    4.002931] calling  mr_init+0x0/0x1b @ 1
[    4.004196] initcall mr_init+0x0/0x1b returned 0 after 1227 usecs
[    4.004200] calling  ntrig_init+0x0/0x1b @ 1
[    4.006597] initcall ntrig_init+0x0/0x1b returned 0 after 2332 usecs
[    4.006600] calling  pl_init+0x0/0x1b @ 1
[    4.008991] initcall pl_init+0x0/0x1b returned 0 after 2327 usecs
[    4.008995] calling  pl_init+0x0/0x1b @ 1
[    4.010282] initcall pl_init+0x0/0x1b returned 0 after 1248 usecs
[    4.010285] calling  samsung_init+0x0/0x1b @ 1
[    4.011572] initcall samsung_init+0x0/0x1b returned 0 after 1249 usecs
[    4.011576] calling  sony_init+0x0/0x1b @ 1
[    4.012871] initcall sony_init+0x0/0x1b returned 0 after 1254 usecs
[    4.012874] calling  sp_init+0x0/0x1b @ 1
[    4.014188] initcall sp_init+0x0/0x1b returned 0 after 1273 usecs
[    4.014191] calling  ts_init+0x0/0x1b @ 1
[    4.016591] initcall ts_init+0x0/0x1b returned 0 after 2335 usecs
[    4.016594] calling  hid_init+0x0/0x78 @ 1
[    4.020369] usbcore: registered new interface driver usbhid
[    4.020373] usbhid: USB HID core driver
[    4.020377] initcall hid_init+0x0/0x78 returned 0 after 3690 usecs
[    4.020380] calling  staging_init+0x0/0x8 @ 1
[    4.020382] initcall staging_init+0x0/0x8 returned 0 after 0 usecs
[    4.020384] calling  easycap_module_init+0x0/0xc2 @ 1
[    4.020386] Easycap version: 0.9.01
[    4.021709] usbcore: registered new interface driver easycap
[    4.021717] initcall easycap_module_init+0x0/0xc2 returned 0 after 1295 usecs
[    4.021719] calling  eeepc_laptop_init+0x0/0x58 @ 1
[    4.027178] initcall eeepc_laptop_init+0x0/0x58 returned -19 after 5314 usecs
[    4.027190] calling  alsa_hwdep_init+0x0/0x64 @ 1
[    4.027216] initcall alsa_hwdep_init+0x0/0x64 returned 0 after 16 usecs
[    4.027225] calling  alsa_timer_init+0x0/0x16f @ 1
[    4.028811] initcall alsa_timer_init+0x0/0x16f returned 0 after 1538 usecs
[    4.028814] calling  snd_hrtimer_init+0x0/0xf9 @ 1
[    4.028818] initcall snd_hrtimer_init+0x0/0xf9 returned 0 after 1 usecs
[    4.028820] calling  alsa_pcm_init+0x0/0x6c @ 1
[    4.028832] initcall alsa_pcm_init+0x0/0x6c returned 0 after 9 usecs
[    4.028834] calling  snd_mem_init+0x0/0x2c @ 1
[    4.028842] initcall snd_mem_init+0x0/0x2c returned 0 after 5 usecs
[    4.028844] calling  alsa_rawmidi_init+0x0/0x85 @ 1
[    4.028847] initcall alsa_rawmidi_init+0x0/0x85 returned 0 after 0 usecs
[    4.028849] calling  alsa_mixer_oss_init+0x0/0x3c @ 1
[    4.028852] initcall alsa_mixer_oss_init+0x0/0x3c returned 0 after 0 usecs
[    4.028854] calling  alsa_pcm_oss_init+0x0/0x88 @ 1
[    4.028856] initcall alsa_pcm_oss_init+0x0/0x88 returned 0 after 0 usecs
[    4.028858] calling  alsa_seq_init+0x0/0x4c @ 1
[    4.030197] initcall alsa_seq_init+0x0/0x4c returned 0 after 1300 usecs
[    4.030200] calling  alsa_seq_device_init+0x0/0x5b @ 1
[    4.030203] initcall alsa_seq_device_init+0x0/0x5b returned 0 after 0 usecs
[    4.030205] calling  alsa_seq_midi_event_init+0x0/0x8 @ 1
[    4.030208] initcall alsa_seq_midi_event_init+0x0/0x8 returned 0 after 0 usecs
[    4.030210] calling  alsa_seq_oss_init+0x0/0x176 @ 1
[    4.041893] initcall alsa_seq_oss_init+0x0/0x176 returned 0 after 11400 usecs
[    4.041896] calling  alsa_seq_dummy_init+0x0/0xbe @ 1
[    4.041904] initcall alsa_seq_dummy_init+0x0/0xbe returned 0 after 5 usecs
[    4.041907] calling  alsa_seq_midi_init+0x0/0x3a @ 1
[    4.041910] initcall alsa_seq_midi_init+0x0/0x3a returned 0 after 0 usecs
[    4.041912] calling  alsa_seq_midi_emul_init+0x0/0x8 @ 1
[    4.041914] initcall alsa_seq_midi_emul_init+0x0/0x8 returned 0 after 0 usecs
[    4.041920] calling  alsa_opl3_init+0x0/0x8 @ 1
[    4.041922] initcall alsa_opl3_init+0x0/0x8 returned 0 after 0 usecs
[    4.041924] calling  alsa_opl3_seq_init+0x0/0x1e @ 1
[    4.041927] initcall alsa_opl3_seq_init+0x0/0x1e returned 0 after 0 usecs
[    4.041929] calling  alsa_mpu401_uart_init+0x0/0x8 @ 1
[    4.041931] initcall alsa_mpu401_uart_init+0x0/0x8 returned 0 after 0 usecs
[    4.041933] calling  alsa_card_cmipci_init+0x0/0x1b @ 1
[    4.043262] initcall alsa_card_cmipci_init+0x0/0x1b returned 0 after 1287 usecs
[    4.043265] calling  patch_realtek_init+0x0/0x12 @ 1
[    4.043268] initcall patch_realtek_init+0x0/0x12 returned 0 after 0 usecs
[    4.043270] calling  patch_cmedia_init+0x0/0x12 @ 1
[    4.043272] initcall patch_cmedia_init+0x0/0x12 returned 0 after 0 usecs
[    4.043275] calling  patch_analog_init+0x0/0x12 @ 1
[    4.043277] initcall patch_analog_init+0x0/0x12 returned 0 after 0 usecs
[    4.043279] calling  patch_sigmatel_init+0x0/0x12 @ 1
[    4.043281] initcall patch_sigmatel_init+0x0/0x12 returned 0 after 0 usecs
[    4.043283] calling  patch_si3054_init+0x0/0x12 @ 1
[    4.043286] initcall patch_si3054_init+0x0/0x12 returned 0 after 0 usecs
[    4.043288] calling  patch_cirrus_init+0x0/0x12 @ 1
[    4.043290] initcall patch_cirrus_init+0x0/0x12 returned 0 after 0 usecs
[    4.043292] calling  patch_ca0110_init+0x0/0x12 @ 1
[    4.043294] initcall patch_ca0110_init+0x0/0x12 returned 0 after 0 usecs
[    4.043296] calling  patch_ca0132_init+0x0/0x12 @ 1
[    4.043298] initcall patch_ca0132_init+0x0/0x12 returned 0 after 0 usecs
[    4.043301] calling  patch_conexant_init+0x0/0x12 @ 1
[    4.043303] initcall patch_conexant_init+0x0/0x12 returned 0 after 0 usecs
[    4.043305] calling  patch_via_init+0x0/0x12 @ 1
[    4.043307] initcall patch_via_init+0x0/0x12 returned 0 after 0 usecs
[    4.043309] calling  patch_hdmi_init+0x0/0x12 @ 1
[    4.043311] initcall patch_hdmi_init+0x0/0x12 returned 0 after 0 usecs
[    4.043313] calling  alsa_card_azx_init+0x0/0x1b @ 1
[    4.044596] initcall alsa_card_azx_init+0x0/0x1b returned 0 after 1243 usecs
[    4.044599] calling  alsa_card_oxygen_init+0x0/0x1b @ 1
[    4.045897] initcall alsa_card_oxygen_init+0x0/0x1b returned 0 after 1258 usecs
[    4.045901] calling  snd_usb_audio_init+0x0/0x3e @ 1
[    4.047220] usbcore: registered new interface driver snd-usb-audio
[    4.047228] initcall snd_usb_audio_init+0x0/0x3e returned 0 after 1290 usecs
[    4.047231] calling  alsa_card_ua101_init+0x0/0x1b @ 1
[    4.049641] usbcore: registered new interface driver snd-ua101
[    4.049650] initcall alsa_card_ua101_init+0x0/0x1b returned 0 after 2356 usecs
[    4.049653] calling  snd_usX2Y_module_init+0x0/0x1b @ 1
[    4.052778] usbcore: registered new interface driver snd-usb-usx2y
[    4.052786] initcall snd_usX2Y_module_init+0x0/0x1b returned 0 after 3053 usecs
[    4.052789] calling  snd_us122l_module_init+0x0/0x1b @ 1
[    4.054983] usbcore: registered new interface driver snd-usb-us122l
[    4.054991] initcall snd_us122l_module_init+0x0/0x1b returned 0 after 2145 usecs
[    4.054994] calling  snd_module_init+0x0/0x1b @ 1
[    4.056902] usbcore: registered new interface driver snd-usb-caiaq
[    4.056909] initcall snd_module_init+0x0/0x1b re usecs
[    4.056913] calling  usb6fire_chip_init+0x0/0x1b @ 1
[    4.058219] usbcore: registered new interface driver    4.058227] initcall usb6fire_chip_init+0x0/0x1b returned 0 aer 1277 usecs
[    4.058229] calling  alsa_sou/0x71 @ 1
[    4.058231] ALSA device list:
[No soundcards found.
[    4.058234] initcall alsa_sound_last_init+0x0/0x71 returned 0 after 2 usecs
[    4.058236] calling  llc_init+0x0/0x20 @ 1
[    4.058239] initcall llc_init+0s
[    4.058241] calling  snap_init+0x0/0x38 @ 1
[    4.058244] initcall snap_init+0x0/0x38 returned 0 after 1 usecs
[    4.058245] calling  rif_init+0x0/0x85 @ 1
[    4.058269] initcall rif_init+0x0/0x85 returned 0 after 21 usecs
[    4.058271] calling  blackhole_module_init+0x0/0x12 @ 1
[    4.058274] initcall blackhole_module_init+0x0/0x12 returned 0 after 0 usecs
[    4.058276] calling  nfnetlink_init+0x0/0x27 @ 1
[    4.058278] Netfilter messages via NETLINK v0.30.
[    4.058289] initcall nfnetlink_init+0x0/0x27 returned 0 after 10 usecs
[    4.058290] calling  nfnetlink_queue_init+0x0/0xa3 @ 1
[    4.058297] initcall nfnetlink_queue_init+0x0/0xa3 returned 0 after 4 usecs
[    4.058298] calling  nfnetlink_log_init+0x0/0xd6 @ 1
[    4.058307] initcall nfnetlink_log_init+0x0/0xd6 returned 0 after 7 usecs
[    4.058309] calling  nf_conntrack_standalone_init+0x0/0x12 @ 1
[    4.058312] nf_conntrack version 0.5.0 (7366 buckets, 29464 max)
[    4.061022] initcall nf_conntrack_standalone_init+0x0/0x12 returned 0 after 2641 usecs
[    4.061025] calling  nf_ct_proto_gre_init+0x0/0x3c @ 1
[    4.061031] initcall nf_ct_proto_gre_init+0x0/0x3c returned 0 after 3 usecs
[    4.061033] calling  ctnetlink_init+0x0/0xd5 @ 1
[    4.061034] ctnetlink v0.93: registering with nfnetlink.
[    4.061037] initcall ctnetlink_init+0x0/0xd5 returned 0 after 2 usecs
[    4.061039] calling  nf_conntrack_ftp_init+0x0/0x19c @ 1
[    4.061046] initcall nf_conntrack_ftp_init+0x0/0x19c returned 0 after 4 usecs
[    4.061048] calling  nf_conntrack_h323_init+0x0/0xcd @ 1
[    4.061096] initcall nf_conntrack_h323_init+0x0/0xcd returned 0 after 45 usecs
[    4.061098] calling  nf_conntrack_irc_init+0x0/0x163 @ 1
[    4.061102] initcall nf_conntrack_irc_init+0x0/0x163 returned 0 after 1 usecs
[    4.061104] calling  nf_conntrack_pptp_init+0x0/0x3c @ 1
[    4.061106] initcall nf_conntrack_pptp_init+0x0/0x3c returned 0 after 0 usecs
[    4.061108] calling  nf_conntrack_sip_init+0x0/0x1f9 @ 1
[    4.061111] initcall nf_conntrack_sip_init+0x0/0x1f9 returned 0 after 0 usecs
[    4.061113] calling  xt_init+0x0/0x11d @ 1
[    4.061117] initcall xt_init+0x0/0x11d returned 0 after 1 usecs
[    4.061118] calling  tcpudp_mt_init+0x0/0x17 @ 1
[    4.061121] initcall tcpudp_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.061123] calling  mark_mt_init+0x0/0x40 @ 1
[    4.061128] initcall mark_mt_init+0x0/0x40 returned 0 after 0 usecs
[    4.061131] calling  connmark_mt_init+0x0/0x40 @ 1
[    4.061133] initcall connmark_mt_init+0x0/0x40 returned 0 after 0 usecs
[    4.061135] calling  audit_tg_init+0x0/0x17 @ 1
[    4.061138] initcall audit_tg_init+0x0/0x17 returned 0 after 0 usecs
[    4.061139] calling  checksum_tg_init+0x0/0x12 @ 1
[    4.061143] initcall checksum_tg_init+0x0/0x12 returned 0 after 0 usecs
[    4.061145] calling  classify_tg_init+0x0/0x17 @ 1
[    4.061150] initcall classify_tg_init+0x0/0x17 returned 0 after 1 usecs
[    4.061152] calling  connsecmark_tg_init+0x0/0x12 @ 1
[    4.061155] initcall connsecmark_tg_init+0x0/0x12 returned 0 after 0 usecs
[    4.061157] calling  dscp_tg_init+0x0/0x17 @ 1
[    4.061159] initcall dscp_tg_init+0x0/0x17 returned 0 after 0 usecs
[    4.061161] calling  hl_tg_init+0x0/0x17 @ 1
[    4.061163] initcall hl_tg_init+0x0/0x17 returned 0 after 0 usecs
[    4.061165] calling  led_tg_init+0x0/0x12 @ 1
[    4.061168] initcall led_tg_init+0x0/0x12 returned 0 after 0 usecs
[    4.061170] calling  nflog_tg_init+0x0/0x12 @ 1
[    4.061172] initcall nflog_tg_init+0x0/0x12 returned 0 after 0 usecs
[    4.061174] calling  nfqueue_tg_init+0x0/0x17 @ 1
[    4.061176] initcall nfqueue_tg_init+0x0/0x17 returned 0 after 0 usecs
[    4.061178] calling  xt_rateest_tg_init+0x0/0x2b @ 1
[    4.061188] initcall xt_rateest_tg_init+0x0/0x2b returned 0 after 0 usecs
[    4.061192] calling  secmark_tg_init+0x0/0x12 @ 1
[    4.061194] initcall secmark_tg_init+0x0/0x12 returned 0 after 0 usecs
[    4.061196] calling  tcpmss_tg_init+0x0/0x17 @ 1
[    4.061198] initcall tcpmss_tg_init+0x0/0x17 returned 0 after 0 usecs
[    4.061199] calling  tcpoptstrip_tg_init+0x0/0x17 @ 1
[    4.061202] initcall tcpoptstrip_tg_init+0x0/0x17 returned 0 after 0 usecs
[    4.061203] calling  tee_tg_init+0x0/0x17 @ 1
[    4.061205] initcall tee_tg_init+0x0/0x17 returned 0 after 0 usecs
[    4.061207] calling  idletimer_tg_init+0x0/0x9e @ 1
[    4.063738] initcall idletimer_tg_init+0x0/0x9e returned 0 after 2463 usecs
[    4.063741] calling  addrtype_mt_init+0x0/0x17 @ 1
[    4.063743] initcall addrtype_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063745] calling  xt_cluster_mt_init+0x0/0x12 @ 1
[    4.063747] initcall xt_cluster_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063749] calling  comment_mt_init+0x0/0x12 @ 1
[    4.063751] initcall comment_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063753] calling  connbytes_mt_init+0x0/0x12 @ 1
[    4.063755] initcall connbytes_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063757] calling  connlimit_mt_init+0x0/0x17 @ 1
[    4.063759] initcall connlimit_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063761] calling  conntrack_mt_init+0x0/0x17 @ 1
[    4.063763] initcall conntrack_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063765] calling  cpu_mt_init+0x0/0x12 @ 1
[    4.063767] initcall cpu_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063768] calling  dccp_mt_init+0x0/0x60 @ 1
[    4.063771] initcall dccp_mt_init+0x0/0x60 returned 0 after 0 usecs
[    4.063773] calling  devgroup_mt_init+0x0/0x12 @ 1
[    4.063775] initcall devgroup_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063777] calling  dscp_mt_init+0x0/0x17 @ 1
[    4.063779] initcall dscp_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063781] calling  esp_mt_init+0x0/0x17 @ 1
[    4.063783] initcall esp_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063784] calling  hashlimit_mt_init+0x0/0x8c @ 1
[    4.063816] initcall hashlimit_mt_init+0x0/0x8c returned 0 after 28 usecs
[    4.063818] calling  helper_mt_init+0x0/0x12 @ 1
[    4.063820] initcall helper_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063822] calling  hl_mt_init+0x0/0x17 @ 1
[    4.063824] initcall hl_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063830] calling  iprange_mt_init+0x0/0x17 @ 1
[    4.063832] initcall iprange_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063834] calling  length_mt_init+0x0/0x17 @ 1
[    4.063836] initcall length_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063838] calling  limit_mt_init+0x0/0x12 @ 1
[    4.063841] initcall limit_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063842] calling  mac_mt_init+0x0/0x12 @ 1
[    4.063844] initcall mac_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063846] calling  multiport_mt_init+0x0/0x17 @ 1
[    4.063848] initcall multiport_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063850] calling  xt_osf_init+0x0/0x8d @ 1
[    4.063853] initcall xt_osf_init+0x0/0x8d returned 0 after 0 usecs
[    4.063855] calling  owner_mt_init+0x0/0x12 @ 1
[    4.063857] initcall owner_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063859] calling  physdev_mt_init+0x0/0x12 @ 1
[    4.063861] initcall physdev_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063863] calling  pkttype_mt_init+0x0/0x12 @ 1
[    4.063865] initcall pkttype_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063867] calling  quota_mt_init+0x0/0x12 @ 1
[    4.063869] initcall quota_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063870] calling  xt_rateest_mt_init+0x0/0x12 @ 1
[    4.063873] initcall xt_rateest_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063874] calling  realm_mt_init+0x0/0x12 @ 1
[    4.063876] initcall realm_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063878] calling  recent_mt_init+0x0/0x7d @ 1
[    4.063882] initcall recent_mt_init+0x0/0x7d returned 0 after 1 usecs
[    4.063884] calling  sctp_mt_init+0x0/0x17 @ 1
[    4.063886] initcall sctp_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063888] calling  state_mt_init+0x0/0x12 @ 1
[    4.063890] initcall state_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063892] calling  statistic_mt_init+0x0/0x12 @ 1
[    4.063894] initcall statistic_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063896] calling  string_mt_init+0x0/0x12 @ 1
[    4.063898] initcall string_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063900] calling  tcpmss_mt_init+0x0/0x17 @ 1
[    4.063902] initcall tcpmss_mt_init+0x0/0x17 returned 0 after 0 usecs
[    4.063904] calling  time_mt_init+0x0/0x54 @ 1
[    4.063905] xt_time: kernel timezone is -0000
[    4.063907] initcall time_mt_init+0x0/0x54 returned 0 after 1 usecs
[    4.063909] calling  u32_mt_init+0x0/0x12 @ 1
[    4.063911] initcall u32_mt_init+0x0/0x12 returned 0 after 0 usecs
[    4.063913] calling  ip_set_init+0x0/0xe4 @ 1
[    4.063916] ip_set: protocol 6
[    4.063917] initcall ip_set_init+0x0/0xe4 returned 0 after 2 usecs
[    4.063919] calling  bitmap_ip_init+0x0/0x12 @ 1
[    4.063921] initcall bitmap_ip_init+0x0/0x12 returned 0 after 0 usecs
[    4.063923] calling  bitmap_ipmac_init+0x0/0x12 @ 1
[    4.063925] initcall bitmap_ipmac_init+0x0/0x12 returned 0 after 0 usecs
[    4.063927] calling  bitmap_port_init+0x0/0x12 @ 1
[    4.063930] initcall bitmap_port_init+0x0/0x12 returned 0 after 0 usecs
[    4.063931] calling  hash_ip_init+0x0/0x12 @ 1
[    4.063933] initcall hash_ip_init+0x0/0x12 returned 0 after 0 usecs
[    4.063935] calling  hash_ipport_init+0x0/0x12 @ 1
[    4.063937] initcall hash_ipport_init+0x0/0x12 returned 0 after 0 usecs
[    4.063940] calling  hash_ipportip_init+0x0/0x12 @ 1
[    4.063942] initcall hash_ipportip_init+0x0/0x12 returned 0 after 0 usecs
[    4.063944] calling  hash_ipportnet_init+0x0/0x12 @ 1
[    4.063946] initcall hash_ipportnet_init+0x0/0x12 returned 0 after 0 usecs
[    4.063948] calling  hash_net_init+0x0/0x12 @ 1
[    4.063950] initcall hash_net_init+0x0/0x12 returned 0 after 0 usecs
[    4.063952] calling  hash_netport_init+0x0/0x12 @ 1
[    4.063954] initcall hash_netport_init+0x0/0x12 returned 0 after 0 usecs
[    4.063956] calling  hash_netiface_init+0x0/0x12 @ 1
[    4.063958] initcall hash_netiface_init+0x0/0x12 returned 0 after 0 usecs
[    4.063960] calling  list_set_init+0x0/0x12 @ 1
[    4.063963] initcall list_set_init+0x0/0x12 returned 0 after 0 us[   10.047279] async_waiting @ 1
[   10.084305] ohci_hcd 0000:00:16.0: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
[   10.125760] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   10.137937] ata1.00: ATA-8: Hitachi HDS722020ALA330, JKAOA20N, max UDMA/133
[   10.144239] usb 7-3: new low-speed USB device number 2 using ohci_hcd
[   10.138852] ata1.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[   10.167382] ata1.00: configured for UDMA/133
[   10.175335] async_waiting @ 25
[   10.175362] ata4: SATA link down (SStatus 0 SControl 300)
[   10.176059] async_continuing @ 25 after 2 usec
[   10.198183] async_waiting @ 1749
[   10.204099] scsi 0:0:0:0: Direct-Access     ATA      Hitachi HDS72202 JKAO PQ: 0 ANSI: 5
[   10.213840] calling  6_sd_probe_async+0x0/0x1d0 @ 1750
[   10.219817] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[   10.225695] ohci_hcd 0000:00:16.0: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
[   10.232039] sd 0:0:0:0: [sda] Write Protect is off
[   10.232947] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   10.244239] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   10.252051] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   10.257043]  sda: sda1 sda2
[   10.267432] initcall 2_async_port_probe+0x0/0x70 returned 0 after 6574710 usecs
[   10.268241] sd 0:0:0:0: [sda] Attached SCSI disk
[   10.268249] initcall 6_sd_probe_async+0x0/0x1d0 returned 0 after 47382 usecs
[   10.286677] async_continuing @ 5 after 308456 usec
[   10.287644] initcall 3_async_port_probe+0x0/0x70 returned 0 after 6610268 usecs
[   10.308658] usb 7-3: skipped 1 descriptor after interface
[   10.309584] usb 7-3: skipped 1 descriptor after interface
[   10.324577] usb 7-3: default lan36044] usb 7-3: udev 2, busnum 7, minor = 769
[   10.336968] usb 7-3: Nce found, idVendor=046d, idProduct=c517
[   10.336968] utrings: Mfr=1, Product=2, SerialNumber=0
[   10.336968] ur
[   10.363174] ata3: SATA link up 3.0 Gbps (SStatus 1236968] usb 7-3: Manufacturer: Logitech
[   10.378035] us  10.378547] ata3.00: ATA-7: SAMSUNG HD103UJ, 1AA01110, max UDMA7
[   10.378550] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[   10.378975] usb 7-3: configuration #1 chosen from 1 choice
[   10.406094] usb 7-3: adding #1, interface 0)
[   10.413861] usbhid 7-3:1.0: usb_pr781] usbhid 7-3:1.0: usb_probe_interface - got id
[   10.427655] ata3.UDMA/133
[   10.434183] async_waiting @ 1111
[   10.431111 after 0 usec
[   10.447229] scsi 2:0:0:0: Direct-Ac103UJ  1AA0 PQ: 0 ANSI: 5
[   10.453538] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:16.0/usb7/7-3/7-3:1.0/input/input2
[   10.455099] lo46D:C517.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:16.0-3/input0
[   10.455123] usb 7-3: adding 7-3:)
[   10.455910] usbhid 7-3:1.1: usb_probe_interface
[  usb_probe_interface - got id
[   10.463732] logitech 00g up Logitech keyboard report descriptor
[   10.464958] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:16.0/usb7/7-3/7-3:1.1/input/input3
[   10.466978] usbhid 7-3:1.1: looking for a minor, starting at 96
[   10.468421] logitech 0003:046D:C517.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:16.0-3/input1
[   10.468450] drivers/usb/core/inode.c: creating file '002'
[   10.468474] hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0008
[   10.468484] hub 7-0:1.0: state 7 ports 4 chg 0000 evt 0008
[   10.542871] calling  7_sd_probe_async+0x0/0x1d0 @ 5
[   10.545315] sd 2:0:0:0: Attached scsi generic sg1 type 0
[   10.546002] initcall 4_async_port_probe+0x0/0x70 returned 0 after 6840985 usecs
[   10.546014] async_continuing @ 1749 after 334079 usec
[   10.546017] initcall 5_async_port_probe+0x0/0x70 returned 0 after 661939 usecs
[   10.579458] async_continuing @ 1 after 514128 usec
[   10.585194] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[   10.585237] sd 2:0:0:0: [sdb] Write Protect is off
[   10.585239] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   10.585257] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   10.585118] async_waiting @ 1
[   10.623200]  sdb: sdb1
[   10.632899] sd 2:0:0:0: [sdb] Attached SCSI disk
[   10.633723] initcall 7_sd_probe_async+0x0/0x1d0 returned 0 after 59138 usecs
[   10.647630] async_continuing @ 1 after 24029 usec
[   10.656565] Freeing unused kernel memory: 784k freed
[   10.657052] Write protecting the kernel read-only data: 14336k
[   10.677558] Freeing unused kernel memory: 1552k freed
[   10.685696] Freeing unused kernel memory: 1000k freed
[   11.560033] calling  wait_scan_init+0x0/0x12 [scsi_wait_scan] @ 2386
[   11.560098] initcall wait_scan_init+0x0/0x12 [scsi_wait_scan] returned 0 after 1 usecs
[   12.498935] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[   14.592229] udev[2470]: starting version 164
[   15.728873] ata1.00: configured for UDMA/133
[   15.736301] ata1: EH complete
[   16.335896] ata1.00: configured for UDMA/133
[   16.335903] ata1: EH complete
[   17.418511] EXT4-fs (dm-0): re-mounted. Opts: (null)
[   17.786285] EXT4-fs (dm-0): re-mounted. Opts: barrier=1,errors=remount-ro
[   20.831684] Adding 2097148k swap on /dev/mapper/serveerstertje-swap.  Priority:-1 extents:1 across:2097148k 
[   21.381386] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: barrier=1,errors=remount-ro
[   23.312492] r8169 0000:08:00.0: eth1: link down
[   23.313625] r8169 0000:08:00.0: eth1: link down
[   23.525963] r8169 0000:09:00.0: eth0: link down
[   23.526058] r8169 0000:09:00.0: eth0: link down
[   24.989710] r8169 0000:08:00.0: eth1: link up
[   25.643314] r8169 0000:09:00.0: eth0: link up
[   42.938940] sshd (5214): /proc/5214/oom_adj is deprecated, please use /proc/5214/oom_score_adj instead.
[   43.697133] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: barrier=1,errors=remount-ro
[   44.206802] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: barrier=1,errors=remount-ro
[   44.776503] EXT4-fs (dm-4): mounted filesystem with ordered data mode. Opts: barrier=1,errors=remount-ro
[  104.382543] EXT4-fs (dm-5): mounted filesystem with ordered data mode. Opts: barrier=1,errors=remount-ro
[  104.717602] EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: barrier=1,errors=remount-ro
[  105.224059] EXT4-fs (dm-8): mounted filesystem with ordered data mode. Opts: barrier=1,errors=remount-ro
[  105.623017] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: barrier=1,errors=remount-ro
[  110.841492] XENBUS: Unable to read cpu state
[  110.854599] XENBUS: Unable to read cpu state
[  110.855246] XENBUS: Unable to read cpu state
[  110.855921] XENBUS: Unable to read cpu state
[  110.857247] XENBUS: Unable to read cpu state
[  110.857883] XENBUS: Unable to read cpu state
[  149.310863] device vif1.0 entered promiscuous mode
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:35:26] traps.c:2432:d1 Domain attempted WRMSR 00000000c0010004 from 0x0000b115c423618f to 0x000000000000abcd.
[  154.048203] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  154.241748] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  154.480991] xen-blkback:ring-ref 10, event-channel 11, protocol 1 (x86_64-abi)
[  154.811304] xen_bridge: port 1(vif1.0) entering forwarding state
[  154.811996] xen_bridge: port 1(vif1.0) entering forwarding state
[  167.939288] device vif2.0 entered promiscuous mode
[  169.824091] xen_bridge: port 1(vif1.0) entering forwarding state
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:35:48] traps.c:2432:d2 Domain attempted WRMSR 00000000c0010004 from 0x00008076c0b94041 to 0x000000000000abcd.
[  176.311981] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  176.589484] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  176.840341] xen_bridge: port 2(vif2.0) entering forwarding state
[  176.841113] xen_bridge: port 2(vif2.0) entering forwarding state
[  191.875514] device vif3.0 entered promiscuous mode
[  191.905062] xen_bridge: port 2(vif2.0) entering forwarding state
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:36:08] traps.c:2432:d3 Domain attempted WRMSR 00000000c0010004 from 0x0000e5f039de6b00 to 0x000000000000abcd.
[  195.823976] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  195.966185] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  196.314463] xen_bridge: port 3(vif3.0) entering forwarding state
[  196.315230] xen_bridge: port 3(vif3.0) entering forwarding state
[  210.265317] device vif4.0 entered promiscuous mode
[  211.361359] xen_bridge: port 3(vif3.0) entering forwarding state
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:36:27] traps.c:2432:d4 Domain attempted WRMSR 00000000c0010004 from 0x0000e5f039de6b00 to 0x000000000000abcd.
[  214.708148] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  214.941373] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  215.233455] xen_bridge: port 4(vif4.0) entering forwarding state
[  215.234246] xen_bridge: port 4(vif4.0) entering forwarding state
[  230.272068] xen_bridge: port 4(vif4.0) entering forwarding state
[  233.169517] device vif5.0 entered promiscuous mode
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:36:49] traps.c:2432:d5 Domain attempted WRMSR 00000000c0010004 from 0x0000ef70fffb1f1e to 0x000000000000abcd.
[  237.039513] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  237.211367] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  237.705018] xen_bridge: port 5(vif5.0) entering forwarding state
[  237.705789] xen_bridge: port 5(vif5.0) entering forwarding state
[  252.768170] xen_bridge: port 5(vif5.0) entering forwarding state
[  259.187235] device vif6.0 entered promiscuous mode
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:37:18] traps.c:2432:d6 Domain attempted WRMSR 00000000c0010004 from 0x0000e5f039de6b00 to 0x000000000000abcd.
[  266.073586] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  267.312485] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  268.323436] xen_bridge: port 6(vif6.0) entering forwarding state
[  268.332869] xen_bridge: port 6(vif6.0) entering forwarding state
[  283.360117] xen_bridge: port 6(vif6.0) entering forwarding state
[  295.368921] device vif7.0 entered promiscuous mode
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:37:52] traps.c:2432:d7 Domain attempted WRMSR 00000000c0010004 from 0x000042b44bcda105 to 0x000000000000abcd.
[  299.264592] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  299.673222] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  299.930837] xen_bridge: port 7(vif7.0) entering forwarding state
[  299.931056] xen_bridge: port 7(vif7.0) entering forwarding state
[  314.976437] xen_bridge: port 7(vif7.0) entering forwarding state
[  324.498221] device vif8.0 entered promiscuous mode
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:38:21] traps.c:2432:d8 Domain attempted WRMSR 00000000c0010004 from 0x0000b115c423618f to 0x000000000000abcd.
[  328.860702] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  329.159954] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  330.284796] xen_bridge: port 8(vif8.0) entering forwarding state
[  330.285064] xen_bridge: port 8(vif8.0) entering forwarding state
[  345.312932] xen_bridge: port 8(vif8.0) entering forwarding state
[  355.007941] device vif9.0 entered promiscuous mode
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:38:52] traps.c:2432:d9 Domain attempted WRMSR 00000000c0010004 from 0x0000ef70fffb1f1e to 0x000000000000abcd.
[  359.398224] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  359.645299] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  360.411346] xen_bridge: port 9(vif9.0) entering forwarding state
[  360.412058] xen_bridge: port 9(vif9.0) entering forwarding state
[  375.456211] xen_bridge: port 9(vif9.0) entering forwarding state
[  412.097865] device vif10.0 entered promiscuous mode
(XEN) [2011-10-26 13:39:45] AMD-Vi: Disable: device id = 0x0400, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:39:45] AMD-Vi: Setup I/O page table: device id = 0x0400, root table = 0x19cee6000, domain = 10, paging mode = 3
(XEN) [2011-10-26 13:39:45] AMD-Vi: Re-assign 04:00.0 from domain 0 to domain 10
(XEN) [2011-10-26 13:39:45] AMD-Vi: Disable: device id = 0x0401, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:39:45] AMD-Vi: Setup I/O page table: device id = 0x0401, root table = 0x19cee6000, domain = 10, paging mode = 3
(XEN) [2011-10-26 13:39:45] AMD-Vi: Re-assign 04:00.1 from domain 0 to domain 10
(XEN) [2011-10-26 13:39:46] AMD-Vi: Disable: device id = 0x0402, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Setup I/O page table: device id = 0x0402, root table = 0x19cee6000, domain = 10, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Re-assign 04:00.2 from domain 0 to domain 10
(XEN) [2011-10-26 13:39:46] AMD-Vi: Disable: device id = 0x0403, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Setup I/O page table: device id = 0x0403, root table = 0x19cee6000, domain = 10, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Re-assign 04:00.3 from domain 0 to domain 10
(XEN) [2011-10-26 13:39:46] AMD-Vi: Disable: device id = 0x0404, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Setup I/O page table: device id = 0x0404, root table = 0x19cee6000, domain = 10, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Re-assign 04:00.4 from domain 0 to domain 10
(XEN) [2011-10-26 13:39:46] AMD-Vi: Disable: device id = 0x0405, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Setup I/O page table: device id = 0x0405, root table = 0x19cee6000, domain = 10, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Re-assign 04:00.5 from domain 0 to domain 10
(XEN) [2011-10-26 13:39:46] AMD-Vi: Disable: device id = 0x0406, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Setup I/O page table: device id = 0x0406, root table = 0x19cee6000, domain = 10, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Re-assign 04:00.6 from domain 0 to domain 10
(XEN) [2011-10-26 13:39:46] AMD-Vi: Disable: device id = 0x0407, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Setup I/O page table: device id = 0x0407, root table = 0x19cee6000, domain = 10, paging mode = 3
(XEN) [2011-10-26 13:39:46] AMD-Vi: Re-assign 04:00.7 from domain 0 to domain 10
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:39:58] traps.c:2432:d10 Domain attempted WRMSR 00000000c0010004 from 0x0000785190f30c4f to 0x000000000000abcd.
[  426.218237] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  426.495027] xen-blkback:ring-ref 10, event-channel 11, protocol 1 (x86_64-abi)
[  426.859967] xen-blkback:ring-ref 11, event-channel 12, protocol 1 (x86_64-abi)
[  427.030422] pciback 0000:04:00.1: enabling device (0000 -> 0002)
[  427.031314] xen: registering gsi 40 triggering 0 polarity 1
[  427.044334] xen_map_pirq_gsi: returning irq 40 for gsi 40
[  427.045056] xen: --> pirq=40 -> irq=40 (gsi=40)
[  427.057344] Already setup the GSI :40
[  427.058275] pciback 0000:04:00.1: PCI INT A -> GSI 40 (level, low) -> IRQ 40
[  427.070847] pciback 0000:04:00.1: setting latency timer to 64
[  427.106436] pciback 0000:04:00.3: enabling device (0000 -> 0002)
[  427.107303] xen: registering gsi 41 triggering 0 polarity 1
[  427.119448] xen_map_pirq_gsi: returning irq 41 for gsi 41
[  427.120288] xen: --> pirq=41 -> irq=41 (gsi=41)
[  427.132304] Already setup the GSI :41
[  427.133269] pciback 0000:04:00.3: PCI INT B -> GSI 41 (level, low) -> IRQ 41
[  427.147542] pciback 0000:04:00.3: setting latency timer to 64
[  427.181348] pciback 0000:04:00.5: enabling device (0000 -> 0002)
[  427.182257] xen: registering gsi 42 triggering 0 polarity 1
[  427.194057] xen_map_pirq_gsi: returning irq 42 for gsi 42
[  427.194971] xen: --> pirq=42 -> irq=42 (gsi=42)
[  427.206819] Already setup the GSI :42
[  427.207789] pciback 0000:04:00.5: PCI INT C -> GSI 42 (level, low) -> IRQ 42
[  427.220231] pciback 0000:04:00.5: setting latency timer to 64
[  427.254579] pciback 0000:04:00.7: enabling device (0000 -> 0002)
[  427.255519] xen: registering gsi 43 triggering 0 polarity 1
[  427.267263] xen_map_pirq_gsi: returning irq 43 for gsi 43
[  427.268177] xen: --> pirq=43 -> irq=43 (gsi=43)
[  427.279702] Already setup the GSI :43
[  427.280658] pciback 0000:04:00.7: PCI INT D -> GSI 43 (level, low) -> IRQ 43
[  427.295435] pciback 0000:04:00.7: setting latency timer to 64
[  427.332743] pciback 0000:04:00.0: enabling device (0000 -> 0002)
[  427.333485] xen: registering gsi 40 triggering 0 polarity 1
[  427.345654] xen_map_pirq_gsi: returning irq 40 for gsi 40
[  427.346149] xen: --> pirq=40 -> irq=40 (gsi=40)
[  427.358050] Already setup the GSI :40
[  427.359022] pciback 0000:04:00.0: PCI INT A -> GSI 40 (level, low) -> IRQ 40
[  427.370484] pciback 0000:04:00.0: setting latency timer to 64
[  427.399757] xen_bridge: port 10(vif10.0) entering forwarding state
[  427.400486] xen_bridge: port 10(vif10.0) entering forwarding state
[  427.436338] pciback 0000:04:00.2: enabling device (0000 -> 0002)
[  427.437148] xen: registering gsi 41 triggering 0 polarity 1
[  427.448937] xen_map_pirq_gsi: returning irq 41 for gsi 41
[  427.449238] xen: --> pirq=41 -> irq=41 (gsi=41)
[  427.460876] Already setup the GSI :41
[  427.461848] pciback 0000:04:00.2: PCI INT B -> GSI 41 (level, low) -> IRQ 41
[  427.473664] pciback 0000:04:00.2: setting latency timer to 64
[  427.537837] pciback 0000:04:00.4: enabling device (0000 -> 0002)
[  427.538618] xen: registering gsi 42 triggering 0 polarity 1
[  427.553297] xen_map_pirq_gsi: returning irq 42 for gsi 42
[  427.554096] xen: --> pirq=42 -> irq=42 (gsi=42)
[  427.568113] Already setup the GSI :42
[  427.568116] pciback 0000:04:00.4: PCI INT C -> GSI 42 (level, low) -> IRQ 42
[  427.569779] pciback 0000:04:00.4: setting latency timer to 64
[  427.631851] pciback 0000:04:00.6: enabling device (0000 -> 0002)
[  427.632571] xen: registering gsi 43 triggering 0 polarity 1
[  427.647171] xen_map_pirq_gsi: returning irq 43 for gsi 43
[  427.648121] xen: --> pirq=43 -> irq=43 (gsi=43)
[  427.662253] Already setup the GSI :43
[  427.663174] pciback 0000:04:00.6: PCI INT D -> GSI 43 (level, low) -> IRQ 43
[  427.676179] pciback 0000:04:00.6: setting latency timer to 64
[  442.432182] xen_bridge: port 10(vif10.0) entering forwarding state
[  475.632533] device vif11.0 entered promiscuous mode
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:40:53] traps.c:2432:d11 Domain attempted WRMSR 00000000c0010004 from 0x00008076c0b94041 to 0x000000000000abcd.
[  480.269700] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  480.602979] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  480.880298] xen_bridge: port 11(vif11.0) entering forwarding state
[  480.885469] xen_bridge: port 11(vif11.0) entering forwarding state
[  495.904912] xen_bridge: port 11(vif11.0) entering forwarding state
[  528.276311] device vif12.0 entered promiscuous mode
(XEN) [2011-10-26 13:41:42] AMD-Vi: Disable: device id = 0x00a4, domain = 0, paging mode = 3
(XEN) [2011-10-26 13:41:42] AMD-Vi: Setup I/O page table: device id = 0x00a4, root table = 0x1f1008000, domain = 12, paging mode = 3
(XEN) [2011-10-26 13:41:42] AMD-Vi: Re-assign 03:06.0 from domain 0 to domain 12
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:41:54] traps.c:2432:d12 Domain attempted WRMSR 00000000c0010004 from 0x0000ef70fffb1f1e to 0x000000000000abcd.
[  541.726044] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  542.595268] pciback 0000:03:06.0: enabling device (0000 -> 0001)
[  542.596198] xen: registering gsi 22 triggering 0 polarity 1
[  542.607895] xen_map_pirq_gsi: returning irq 22 for gsi 22
[  542.608271] xen: --> pirq=22 -> irq=22 (gsi=22)
[  542.621625] Already setup the GSI :22
[  542.622115] pciback 0000:03:06.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[  542.690414] xen-blkback:ring-ref 10, event-channel 11, protocol 1 (x86_64-abi)
[  543.432928] xen_bridge: port 12(vif12.0) entering forwarding state
[  543.433620] xen_bridge: port 12(vif12.0) entering forwarding state
[  558.496135] xen_bridge: port 12(vif12.0) entering forwarding state
(XEN) [2011-10-26 13:43:35] grant_table.c:237:d0 Increased maptrack size to 2 frames.
[  776.857780] device vif13.0 entered promiscuous mode
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:46:25] traps.c:2432:d13 Domain attempted WRMSR 00000000c0010004 from 0x0000e5f039de6b00 to 0x000000000000abcd.
[  812.956876] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  813.387490] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  815.245615] xen_bridge: port 13(vif13.0) entering forwarding state
[  815.246250] xen_bridge: port 13(vif13.0) entering forwarding state
[  830.304518] xen_bridge: port 13(vif13.0) entering forwarding state
[  888.020943] device vif14.0 entered promiscuous mode
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:47:52] traps.c:2432:d14 Domain attempted WRMSR 00000000c0010004 from 0x0000e5f039de6b00 to 0x000000000000abcd.
[  899.340172] xen-blkback:ring-ref 8, event-channel 9, protocol 1 (x86_64-abi)
[  900.180201] xen-blkback:ring-ref 9, event-channel 10, protocol 1 (x86_64-abi)
[  900.587796] vpn_bridge: port 1(vif14.0) entering forwarding state
[  900.590855] vpn_bridge: port 1(vif14.0) entering forwarding state
[  915.616131] vpn_bridge: port 1(vif14.0) entering forwarding state
[  966.801204] device vif15.0 entered promiscuous mode
mapping kernel into physical memory
about to get started...
(XEN) [2011-10-26 13:49:12] traps.c:2432:d15 Domain attempted WRMSR 00000000c0010004 from 0x0000ef70fffb1f1e to 0x000000000000abcd.
[  980.168662] xen-blkback:ring-ref 8, event-channel 15, protocol 1 (x86_64-abi)
[  980.697062] xen-blkback:ring-ref 9, event-channel 16, protocol 1 (x86_64-abi)
[  981.891801] xen_bridge: port 14(vif15.0) entering forwarding state
[  981.892521] xen_bridge: port 14(vif15.0) entering forwarding state
[  996.896432] xen_bridge: port 14(vif15.0) entering forwarding state

[-- Attachment #3: Type: text/plain, Size: 138 bytes --]

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: Panic:: handle_irq_event_percpu
  2011-10-26 14:12             ` Sander Eikelenboom
@ 2011-10-26 14:21               ` Wei Huang
  0 siblings, 0 replies; 9+ messages in thread
From: Wei Huang @ 2011-10-26 14:21 UTC (permalink / raw)
  To: Sander Eikelenboom; +Cc: xen-devel@lists.xensource.com, Rzeszutek Wilk, Konrad

That is good. We are preparing a series of patches for xen-4.1.3. They 
should be out in next few days. Thanks for your help on testing.

-Wei

On 10/26/2011 09:12 AM, Sander Eikelenboom wrote:
> Hello Wei,
>
> Sorry you were right, i'm a bit accustomed that patches apply to the root of the project, this one was for /xen specifically.
> I have done a lot of reboots with the patch applied on:
> - xen 4.1.3-rc1-pre
> - dom0 kernel from Konrad's linux-next tree + devel/acpi-cpufreq.v3 branch + patch from liang tang + linus 3.1 tree pulled in.
> - iommu specific boot options used for xen in grub: iommu=on,amd-iommu-debug amd_iommu=on amd-iommu-debug
>
> I haven't seen kernel panics on boot so far, is this output that was expected (from serial console):
>
> <snip>
> (XEN) AMD-Vi: Add device table entry: device id = 0x0a07, interupt table = 0x24e004000
> (XEN) AMD-Vi: Add device table entry: device id = 0x0b00, interupt table = 0x24e004000
> (XEN) AMD-Vi: IOMMU 0 Enabled.
> (XEN) AMD-Vi: Enabling global vector map
> (XEN) I/O virtualisation enabled
> (XEN)  - Dom0 mode: Relaxed
> (XEN) Getting VERSION: 80050010
> <snip>
>
> Complete serial console output is attached
>
>
> Is this patch a candidate for 4.1.3 ?
>
> --
>
> Sander
>
>
>
> Monday, October 24, 2011, 11:51:39 PM, you wrote:
>
>> Yes, it is for xen-4.1-testing tree. I just applied it to the latest tip (23174:d4253bc5418b). There were some hunks; but it worked in general. Could you try it and replace your xen.gz file with the new version?
>> (Stripping trailing CRs from patch.)
>> patching file arch/x86/io_apic.c
>> Hunk #1 succeeded at 548 (offset -21 lines).
>> (Stripping trailing CRs from patch.)
>> patching file arch/x86/irq.c
>> Hunk #5 succeeded at 192 (offset 1 line).
>> Hunk #6 succeeded at 225 (offset 1 line).
>> Hunk #7 succeeded at 236 (offset 1 line).
>> Hunk #8 succeeded at 302 (offset 1 line).
>> Hunk #9 succeeded at 372 (offset 1 line).
>> Hunk #10 succeeded at 425 (offset 1 line).
>> Hunk #11 succeeded at 440 (offset 1 line).
>> Hunk #12 succeeded at 476 (offset 1 line).
>> Hunk #13 succeeded at 497 (offset 1 line).
>> Hunk #14 succeeded at 1599 (offset -11 lines).
>> Hunk #15 succeeded at 1647 (offset -11 lines).
>> (Stripping trailing CRs from patch.)
>> patching file drivers/passthrough/amd/pci_amd_iommu.c
>> (Stripping trailing CRs from patch.)
>> patching file include/asm-x86/irq.h
>> (Stripping trailing CRs from patch.)
>> patching file include/xen/pci.h
>
>
>> -Wei
>> On 10/22/2011 09:57 AM, Sander Eikelenboom wrote:
>>> Hello Wei,
>>>
>>> Is this for xen 4.1.2 ?
>>> All hunks of the patch seem to be rejected.
>>>
>>> --
>>> Sander
>>>
>>>
>>> Wednesday, October 19, 2011, 8:27:55 PM, you wrote:
>>>
>>>> This reminds me of 23768:09595fdf3638, which reverted WeiWang's patch of forcing perdev-intremap as default. Could you try the attached patch on your Xen 4.1 tree and test with patched xen.gz?
>>>> Thanks,
>>>> -Wei
>>>> -----Original Message-----
>>>> From: xen-devel-bounces@lists.xensource.com [mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Sander Eikelenboom
>>>> Sent: Wednesday, October 19, 2011 12:30 PM
>>>> To: Huang2, Wei
>>>> Cc: xen-devel@lists.xensource.com; Konrad Rzeszutek Wilk
>>>> Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu
>>>> Hello Wei,
>>>> Result is that using only "1" or "1" in combination with "2" always result in SATA I/O errors, so that doesn't boot.
>>>> Haven't tried rebooting a lot of times without iommu yet.
>>>> (the reason i bought the 890fx board in the first place)
>>>> Will try that a few times when i have some more time.
>>>> --
>>>> Sander
>>>> Wednesday, October 19, 2011, 6:38:38 PM, you wrote:
>>>>> It looks similar.
>>>>> Hi Sander, could you please test your system with the following options?
>>>>> 1. iommu=amd-iommu-perdev-intremap in xen.gz GRUB entry
>>>>> 2. pci=nosmi in pvops GRUB entry
>>>>> 3. iommu=0 in xen.gz GRUB entry [optional, only if (1) doesn't work for you]
>>>>> We were seeing an issue which was caused by messed-up interrupt remap table. George Dunlap's perdev interrupt map solved our problem.
>>>>> Thanks,
>>>>> -Wei
>>>>> -----Original Message-----
>>>>> From: Konrad Rzeszutek Wilk [mailto:konrad.wilk@oracle.com]
>>>>> Sent: Wednesday, October 19, 2011 11:08 AM
>>>>> To: Sander Eikelenboom; Huang2, Wei
>>>>> Cc: xen-devel@lists.xensource.com
>>>>> Subject: Re: [Xen-devel] Panic:: handle_irq_event_percpu
>>>>> On Tue, Oct 18, 2011 at 08:55:19PM +0200, Sander Eikelenboom wrote:
>>>>>> Hi Konrad,
>>>>>>
>>>>>> On my system (AND phenom x6, 8gb mem) running xen 4.1.2-rc3
>>>>>> and a custom kernel based on:
>>>>>>
>>>>>> - your linux-next branch
>>>>>> - pulled in your apci/cpufreq branch
>>>>>> - pulled in latest patches from linuses tree
>>>>> Wei,
>>>>> Are those similar to what you had been seeing?
>>>>>> I'm experiencing infrequent panics at boot (say 1 out of 10 or 20 boots), doesn't seem to matter if it's a cold or a warm boot.
>>>>>> It always seem to happen during or shortly after booting. When it doesn't occur then, it can run for at least several days/weeks (haven't seen it panic then).
>>>>>> It doesn't seem to happen at a particular point at or shortly after booting, but it happens before starting any guests
>>>>>>
>>>>>> Unfortunately i haven't had serial console enabled at these times, but i have made some photo's.
>>>>>> The first 3 times it locked completely before being able to print a stacktrace, the 4th time it did (although the photo is a bit unsharp).
>>>>>>
>>>>>>
>>>>>> So all in all, it kind of strange, i hope you can figure something out from the stacktrace, if not, i will see if i can try with serial console attached.
>>>>>>
>>>>>> --
>>>>>> Sander
>>>
>>>
>>>
>>>
>>>>>> _______________________________________________
>>>>>> Xen-devel mailing list
>>>>>> Xen-devel@lists.xensource.com
>>>>>> http://lists.xensource.com/xen-devel
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>
>
>
>

^ permalink raw reply	[flat|nested] 9+ messages in thread

end of thread, other threads:[~2011-10-26 14:21 UTC | newest]

Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-10-18 18:55 Panic:: handle_irq_event_percpu Sander Eikelenboom
2011-10-19 16:08 ` Konrad Rzeszutek Wilk
2011-10-19 16:38   ` Huang2, Wei
2011-10-19 17:30     ` Sander Eikelenboom
2011-10-19 18:27       ` Huang2, Wei
2011-10-22 14:57         ` Sander Eikelenboom
2011-10-24 21:51           ` Wei Huang
2011-10-26 14:12             ` Sander Eikelenboom
2011-10-26 14:21               ` Wei Huang

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.