From: prylowski@metasoft.pl (Rafal Prylowski)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 1/5] dmaengine: add ep93xx DMA support
Date: Wed, 16 Nov 2011 09:31:44 +0100 [thread overview]
Message-ID: <4EC374F0.8000400@metasoft.pl> (raw)
In-Reply-To: <20111116065512.GB2703@mwesterb-mobl.ger.corp.intel.com>
Hello.
W dniu 2011-11-16 07:55, Mika Westerberg pisze:
> Yes, this is certainly a copy-paste bug or something. Thanks for fixing :)
>
> Can you send a separate patch for this? Make sure you Cc Vinod Koul as he is
> the maintainer of slave dma subsystem.
Here is a separate patch:
Index: linux-2.6/drivers/dma/ep93xx_dma.c
===================================================================
--- linux-2.6.orig/drivers/dma/ep93xx_dma.c
+++ linux-2.6/drivers/dma/ep93xx_dma.c
@@ -459,9 +459,6 @@ static int m2m_hw_setup(struct ep93xx_dm
* This IDE part is totally untested. Values below are taken
* from the EP93xx Users's Guide and might not be correct.
*/
- control |= M2M_CONTROL_NO_HDSK;
- control |= M2M_CONTROL_RSS_IDE;
- control |= M2M_CONTROL_PW_16;
if (data->direction == DMA_TO_DEVICE) {
/* Worst case from the UG */
@@ -473,6 +470,9 @@ static int m2m_hw_setup(struct ep93xx_dm
control |= M2M_CONTROL_SAH;
control |= M2M_CONTROL_TM_RX;
}
+ control |= M2M_CONTROL_NO_HDSK;
+ control |= M2M_CONTROL_RSS_IDE;
+ control |= M2M_CONTROL_PW_16;
break;
default:
>
>> 2) Kernel oops when trying to stop running transfers by calling
>> dmaengine_terminate_all(...) - caused by dereferencing empty list
>> in ep93xx_dma_get_active
>
> Can you post that OOPS log? I would like to understand this problem a bit
> better before we do any fixes for the driver.
>
OOPS log:
Linux version 3.2.0-rc1EP-1+ (prylowski at server) (gcc version 4.4.2 (GCC) ) #1008
Wed Nov 16 08:25:45 CET 2011
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: Metasoft FonTel EP Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: mtdparts=physmap-flash.0:128K(uboot),1152K(kernel),15104K(r
ootfs) root=/dev/mtdblock2 rootfstype=jffs2 console=ttyAM0 init=/sbin/init early
printk lpj=496128 panic=2
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 27452k/27452k available, 5316k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc2800000 - 0xfe800000 ( 960 MB)
lowmem : 0xc0000000 - 0xc2000000 ( 32 MB)
modules : 0xbf000000 -0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc029d000 (2644 kB)
.init : 0xc029d000 - 0xc02b6000 ( 100 kB)
.data : 0xc02b6000 - 0xc02d1440 ( 110 kB)
.bss : 0xc02d1464 - 0xc02df51c ( 57 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:120
VIC @fefb0000: id 0x00041190, vendor 0x41
VIC @fefc0000: id 0x00041190, vendor 0x41
Console: colour dummy device 80x30
Calibrating delay loop (skipped) preset value.. 99.22 BogoMIPS (lpj=496128)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
ep93xx clock: PLL1 running at 400 MHz, PLL2 at 192 MHz
ep93xx clock: FCLK 200 MHz, HCLK 100 MHz, PCLK 50 MHz
bio: create slab <bio-0> at 0
ep93xx-dma ep93xx-dma-m2p: EP93xx M2P DMA ready
ep93xx-dma ep93xx-dma-m2m: EP93xx M2M DMA ready
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.0: using pins 49 (SDA) and 48 (SCL)
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hashable entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) ?? 2001-2006 Red Hat, Inc.
msgmni has been set to 53
io scheduler noop registered
io scheduler deadline registered (default)
Serial: AMBA driver
apb:uart1: ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA
console [ttyAM0] enabled
apb:uart2: ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA
apb:uart3: ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA
fontel-pri fontel-pri: FonTel PRI initialized correctly.
ep93xx-ide ep93xx-ide: version 0.5
scsi0 : ep93xx-ide
ata1: PATA max UDMA/66 irq 40
physmap platform flash device: 01000000 at 60000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00
0001 Chip ID 0x002101
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
3 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 3 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000020000 : "uboot"
0x000000020000-0x000000140000 : "kernel"
0x000000140000-0x000001000000 : "rootfs"
ep93xx-spi ep93xx-spi.0: EP93xx SPI Controller at 0x808a0000 irq 53
ep93xx-eth version 0.1 loading
eth0: ep93xx on-chip ethernet, IRQ 39, 8e:42:5c:13:29:4c
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ep93xx-ohci ep93xx-ohci: EP93xx OHCI
ep93xx-ohci ep93xx-ohci: new USB bus registered, assigned bus number 1
ep93xx-ohci ep93xx-ohci: irq 56, io mem 0x80020000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver fontel
rtc-ds1307 0-0068: rtc core: registered ds1307 as rtc0
rtc-ds1307 0-0068: 56 bytes nvram
ep93xx-rtc ep93xx-rtc: rtc core: registered ep93xx-rtc as rtc1
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec soft
_panic=0 (nowayout= 0)
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
ep93xx-rtc ep93xx-rtc: setting system clock to 1970-01-01 00:00:07 UTC (7)
ata1.00: ATA-8: WDC WD3200BEVE-00A0HT0, 11.01A11, max UDMA/100
ata1.00: 625142448 sectors, multi 0: LBA48
ata1.00: configured for UDMA/66
scsi 0:0:0:0: Direct-Access ATA WDC WD3200BEVE-0 11.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
Internal error: Oops - undefined instruction: 0 [#1]
CPU: 0 Not tainted (3.2.0-rc1EP-1+ #1008)
PC is at 0xc184c868
LR is at ep93xx_dma_tasklet+0xec/0x164
pc : [<c184c868>] lr : [<c012b528>] psr: 00000013
sp : c02b7e70 ip : ffffffff fp : c02b7ea4
r10: 00000100 r9 : 80000013 r8 : c02b7e50
r7 : c02b7e70 r6 : c02b7ea4 r5 : 000000a4 r4 : c02b7e70
r3 : c02b751d r2 : 8ae34598 r1 : c184c6e0 r0 : c02b7ea4
Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: c000717f Table: c0004000 DAC: 00000017
Process swapper (pid: 0, stack limit = 0xc02b6270)
Stack: (0xc02b7e70 to 0xc02b8000)
7e60: c02b7ea4 c02b7e70 c0008b64 c02bd5c4
7e80: c02d60e0 00000000 00000000 c02bd44c c02d60e0 00000100 c02b7ec4 c02b7ea8
7ea0: c001c49c c012b44c 00000018 00000001 c02d60e0 c02b6000 c02b7f04 c02b7ec8
7ec0: c001cbc0 c001c3e4 c02b7eec c02b7ed8 00000006 0000000a c02bf674 c02c458c
7ee0: 00000011 00000000 c02b7f7c c0004000 41129200 c02b0c80 c02b7f14 c02b7f08
7f00: c001cdd0 c001cb38 c02b7f34 c02b7f18 c000983c c001cd98 c0009a60 60000013
7f20: fefb0001 c02b7f7c c02b7f44 c02b7f38 c0008190 c0009810 c02b7f9c c02b7f48
7f40: c0008b64 c0008190 c02c2bf8 00000002 c02b7f90 60000013 c02b6000 c02d1504
7f60: c02baa88 c02baa80 c0004000 41129200 c02b0c80 c02b7f9c c02b7fa0 c02b7f90
7f80: c0009a54 c0009a60 60000013 ffffffff c02b7fbc c02b7fa0 c000a03c c0009a40
7fa0: c02b80b0 c02b19dc c02b19d8 c02baa80 c02b7fcc c02b7fc0 c02384e4 c0009fd4
7fc0: c02b7ff4 c02b7fd0 c029d924 c0238494 c029d49c 00000000 00000000 c02b19dc
7fe0: c0007175 c02b803c 00000000 c02b7ff8 c000803c c029d700 00000000 00000000
Backtrace:
[<c012b43c>] (ep93xx_dma_tasklet+0x0/0x164) from [<c001c49c>] (tasklet_action+0x
c8/0xdc)
[<c001c3d4>] (tasklet_action+0x0/0xdc) from [<c001cbc0>] (__do_softirq+0x98/0x15
4)
r7:c02b6000 r6:c02d60e0 r5:00000001 r4:00000018
[<c001cb28>] (__do_softirq+0x0/0x154) from [<c001cdd0>] (irq_exit+0x48/0x50)
[<c001cd88>] (irq_exit+0x0/0x50) from [<c000983c>] (handle_IRQ+0x3c/0x8c)
[<c0009800>] (handle_IRQ+0x0/0x8c) from [<c0008190>] (asm_do_IRQ+0x10/0x14)
r7:c02b7f7c r6:fefb0001 r5:60000013 r4:c0009a60
[<c0008180>] (asm_do_IRQ+0x0/0x14) from [<c0008b64>] (__irq_svc+0x24/0xc0)
Exception stack(0xc02b7f48 to 0xc02b7f90)
7f40: c02c2bf8 00000002 c02b7f90 60000013 c02b6000 c02d1504
7f60: c02baa88 c02baa80 c0004000 41129200 c02b0c80 c02b7f9c c02b7fa0 c02b7f90
7f80: c0009a54 c0009a60 60000013 ffffffff
[<c0009a30>] (default_idle+0x0/0x34) from [<c000a03c>] (cpu_idle+0x78/0xb0)
[<c0009fc4>] (cpu_idle+0x0/0xb0) from [<c02384e4>] (rest_init+0x60/0x78)
r7:c02baa80 r6:c02b19d8 r5:c02b19dc r4:c02b80b0
[<c0238484>] (rest_init+0x0/0x78) from [<c029d924>] (start_kernel+0x234/0x278)
[<c029d6f0>] (start_kernel+0x0/0x278) from [<c000803c>] (0xc000803c)
r5:c02b803c r4:c0007175
Code: 42555300 54535953 643d4d45 65766972 (53007372)
---[ end trace a494979f60859f42 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 2 seconds..
I'm trying to call dmaengine_terminate_all from function assigned as libata .bmdma_stop.
Maybe this is incorrect, and this bug report is invalid...
Regards,
Rafal Prylowski.
WARNING: multiple messages have this Message-ID (diff)
From: Rafal Prylowski <prylowski@metasoft.pl>
To: Mika Westerberg <mika.westerberg@iki.fi>
Cc: linux-arm-kernel@lists.infradead.org, rmallon@gmail.com,
vinod.koul@intel.com, broonie@opensource.wolfsonmicro.com,
linux-kernel@vger.kernel.org, grant.likely@secretlab.ca,
hsweeten@visionengravers.com, dan.j.williams@intel.com,
lrg@ti.com
Subject: Re: [PATCH v2 1/5] dmaengine: add ep93xx DMA support
Date: Wed, 16 Nov 2011 09:31:44 +0100 [thread overview]
Message-ID: <4EC374F0.8000400@metasoft.pl> (raw)
In-Reply-To: <20111116065512.GB2703@mwesterb-mobl.ger.corp.intel.com>
Hello.
W dniu 2011-11-16 07:55, Mika Westerberg pisze:
> Yes, this is certainly a copy-paste bug or something. Thanks for fixing :)
>
> Can you send a separate patch for this? Make sure you Cc Vinod Koul as he is
> the maintainer of slave dma subsystem.
Here is a separate patch:
Index: linux-2.6/drivers/dma/ep93xx_dma.c
===================================================================
--- linux-2.6.orig/drivers/dma/ep93xx_dma.c
+++ linux-2.6/drivers/dma/ep93xx_dma.c
@@ -459,9 +459,6 @@ static int m2m_hw_setup(struct ep93xx_dm
* This IDE part is totally untested. Values below are taken
* from the EP93xx Users's Guide and might not be correct.
*/
- control |= M2M_CONTROL_NO_HDSK;
- control |= M2M_CONTROL_RSS_IDE;
- control |= M2M_CONTROL_PW_16;
if (data->direction == DMA_TO_DEVICE) {
/* Worst case from the UG */
@@ -473,6 +470,9 @@ static int m2m_hw_setup(struct ep93xx_dm
control |= M2M_CONTROL_SAH;
control |= M2M_CONTROL_TM_RX;
}
+ control |= M2M_CONTROL_NO_HDSK;
+ control |= M2M_CONTROL_RSS_IDE;
+ control |= M2M_CONTROL_PW_16;
break;
default:
>
>> 2) Kernel oops when trying to stop running transfers by calling
>> dmaengine_terminate_all(...) - caused by dereferencing empty list
>> in ep93xx_dma_get_active
>
> Can you post that OOPS log? I would like to understand this problem a bit
> better before we do any fixes for the driver.
>
OOPS log:
Linux version 3.2.0-rc1EP-1+ (prylowski@server) (gcc version 4.4.2 (GCC) ) #1008
Wed Nov 16 08:25:45 CET 2011
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: Metasoft FonTel EP Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: mtdparts=physmap-flash.0:128K(uboot),1152K(kernel),15104K(r
ootfs) root=/dev/mtdblock2 rootfstype=jffs2 console=ttyAM0 init=/sbin/init early
printk lpj=496128 panic=2
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 27452k/27452k available, 5316k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc2800000 - 0xfe800000 ( 960 MB)
lowmem : 0xc0000000 - 0xc2000000 ( 32 MB)
modules : 0xbf000000 -0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc029d000 (2644 kB)
.init : 0xc029d000 - 0xc02b6000 ( 100 kB)
.data : 0xc02b6000 - 0xc02d1440 ( 110 kB)
.bss : 0xc02d1464 - 0xc02df51c ( 57 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:120
VIC @fefb0000: id 0x00041190, vendor 0x41
VIC @fefc0000: id 0x00041190, vendor 0x41
Console: colour dummy device 80x30
Calibrating delay loop (skipped) preset value.. 99.22 BogoMIPS (lpj=496128)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
ep93xx clock: PLL1 running at 400 MHz, PLL2 at 192 MHz
ep93xx clock: FCLK 200 MHz, HCLK 100 MHz, PCLK 50 MHz
bio: create slab <bio-0> at 0
ep93xx-dma ep93xx-dma-m2p: EP93xx M2P DMA ready
ep93xx-dma ep93xx-dma-m2m: EP93xx M2M DMA ready
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.0: using pins 49 (SDA) and 48 (SCL)
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hashable entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 53
io scheduler noop registered
io scheduler deadline registered (default)
Serial: AMBA driver
apb:uart1: ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA
console [ttyAM0] enabled
apb:uart2: ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA
apb:uart3: ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA
fontel-pri fontel-pri: FonTel PRI initialized correctly.
ep93xx-ide ep93xx-ide: version 0.5
scsi0 : ep93xx-ide
ata1: PATA max UDMA/66 irq 40
physmap platform flash device: 01000000 at 60000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00
0001 Chip ID 0x002101
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
3 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 3 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000020000 : "uboot"
0x000000020000-0x000000140000 : "kernel"
0x000000140000-0x000001000000 : "rootfs"
ep93xx-spi ep93xx-spi.0: EP93xx SPI Controller at 0x808a0000 irq 53
ep93xx-eth version 0.1 loading
eth0: ep93xx on-chip ethernet, IRQ 39, 8e:42:5c:13:29:4c
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ep93xx-ohci ep93xx-ohci: EP93xx OHCI
ep93xx-ohci ep93xx-ohci: new USB bus registered, assigned bus number 1
ep93xx-ohci ep93xx-ohci: irq 56, io mem 0x80020000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver fontel
rtc-ds1307 0-0068: rtc core: registered ds1307 as rtc0
rtc-ds1307 0-0068: 56 bytes nvram
ep93xx-rtc ep93xx-rtc: rtc core: registered ep93xx-rtc as rtc1
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec soft
_panic=0 (nowayout= 0)
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
ep93xx-rtc ep93xx-rtc: setting system clock to 1970-01-01 00:00:07 UTC (7)
ata1.00: ATA-8: WDC WD3200BEVE-00A0HT0, 11.01A11, max UDMA/100
ata1.00: 625142448 sectors, multi 0: LBA48
ata1.00: configured for UDMA/66
scsi 0:0:0:0: Direct-Access ATA WDC WD3200BEVE-0 11.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
Internal error: Oops - undefined instruction: 0 [#1]
CPU: 0 Not tainted (3.2.0-rc1EP-1+ #1008)
PC is at 0xc184c868
LR is at ep93xx_dma_tasklet+0xec/0x164
pc : [<c184c868>] lr : [<c012b528>] psr: 00000013
sp : c02b7e70 ip : ffffffff fp : c02b7ea4
r10: 00000100 r9 : 80000013 r8 : c02b7e50
r7 : c02b7e70 r6 : c02b7ea4 r5 : 000000a4 r4 : c02b7e70
r3 : c02b751d r2 : 8ae34598 r1 : c184c6e0 r0 : c02b7ea4
Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: c000717f Table: c0004000 DAC: 00000017
Process swapper (pid: 0, stack limit = 0xc02b6270)
Stack: (0xc02b7e70 to 0xc02b8000)
7e60: c02b7ea4 c02b7e70 c0008b64 c02bd5c4
7e80: c02d60e0 00000000 00000000 c02bd44c c02d60e0 00000100 c02b7ec4 c02b7ea8
7ea0: c001c49c c012b44c 00000018 00000001 c02d60e0 c02b6000 c02b7f04 c02b7ec8
7ec0: c001cbc0 c001c3e4 c02b7eec c02b7ed8 00000006 0000000a c02bf674 c02c458c
7ee0: 00000011 00000000 c02b7f7c c0004000 41129200 c02b0c80 c02b7f14 c02b7f08
7f00: c001cdd0 c001cb38 c02b7f34 c02b7f18 c000983c c001cd98 c0009a60 60000013
7f20: fefb0001 c02b7f7c c02b7f44 c02b7f38 c0008190 c0009810 c02b7f9c c02b7f48
7f40: c0008b64 c0008190 c02c2bf8 00000002 c02b7f90 60000013 c02b6000 c02d1504
7f60: c02baa88 c02baa80 c0004000 41129200 c02b0c80 c02b7f9c c02b7fa0 c02b7f90
7f80: c0009a54 c0009a60 60000013 ffffffff c02b7fbc c02b7fa0 c000a03c c0009a40
7fa0: c02b80b0 c02b19dc c02b19d8 c02baa80 c02b7fcc c02b7fc0 c02384e4 c0009fd4
7fc0: c02b7ff4 c02b7fd0 c029d924 c0238494 c029d49c 00000000 00000000 c02b19dc
7fe0: c0007175 c02b803c 00000000 c02b7ff8 c000803c c029d700 00000000 00000000
Backtrace:
[<c012b43c>] (ep93xx_dma_tasklet+0x0/0x164) from [<c001c49c>] (tasklet_action+0x
c8/0xdc)
[<c001c3d4>] (tasklet_action+0x0/0xdc) from [<c001cbc0>] (__do_softirq+0x98/0x15
4)
r7:c02b6000 r6:c02d60e0 r5:00000001 r4:00000018
[<c001cb28>] (__do_softirq+0x0/0x154) from [<c001cdd0>] (irq_exit+0x48/0x50)
[<c001cd88>] (irq_exit+0x0/0x50) from [<c000983c>] (handle_IRQ+0x3c/0x8c)
[<c0009800>] (handle_IRQ+0x0/0x8c) from [<c0008190>] (asm_do_IRQ+0x10/0x14)
r7:c02b7f7c r6:fefb0001 r5:60000013 r4:c0009a60
[<c0008180>] (asm_do_IRQ+0x0/0x14) from [<c0008b64>] (__irq_svc+0x24/0xc0)
Exception stack(0xc02b7f48 to 0xc02b7f90)
7f40: c02c2bf8 00000002 c02b7f90 60000013 c02b6000 c02d1504
7f60: c02baa88 c02baa80 c0004000 41129200 c02b0c80 c02b7f9c c02b7fa0 c02b7f90
7f80: c0009a54 c0009a60 60000013 ffffffff
[<c0009a30>] (default_idle+0x0/0x34) from [<c000a03c>] (cpu_idle+0x78/0xb0)
[<c0009fc4>] (cpu_idle+0x0/0xb0) from [<c02384e4>] (rest_init+0x60/0x78)
r7:c02baa80 r6:c02b19d8 r5:c02b19dc r4:c02b80b0
[<c0238484>] (rest_init+0x0/0x78) from [<c029d924>] (start_kernel+0x234/0x278)
[<c029d6f0>] (start_kernel+0x0/0x278) from [<c000803c>] (0xc000803c)
r5:c02b803c r4:c0007175
Code: 42555300 54535953 643d4d45 65766972 (53007372)
---[ end trace a494979f60859f42 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 2 seconds..
I'm trying to call dmaengine_terminate_all from function assigned as libata .bmdma_stop.
Maybe this is incorrect, and this bug report is invalid...
Regards,
Rafal Prylowski.
next prev parent reply other threads:[~2011-11-16 8:31 UTC|newest]
Thread overview: 72+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-05-29 10:10 [PATCH v2 0/5] ep93xx DMA patches Mika Westerberg
2011-05-29 10:10 ` Mika Westerberg
2011-05-29 10:10 ` [PATCH v2 1/5] dmaengine: add ep93xx DMA support Mika Westerberg
2011-05-29 10:10 ` Mika Westerberg
2011-11-15 15:02 ` Rafal Prylowski
2011-11-15 15:02 ` Rafal Prylowski
2011-11-15 17:59 ` H Hartley Sweeten
2011-11-15 17:59 ` H Hartley Sweeten
2011-11-16 6:48 ` Mika Westerberg
2011-11-16 6:48 ` Mika Westerberg
2011-11-16 9:00 ` Rafal Prylowski
2011-11-16 9:00 ` Rafal Prylowski
2011-11-16 6:55 ` Mika Westerberg
2011-11-16 6:55 ` Mika Westerberg
2011-11-16 8:31 ` Rafal Prylowski [this message]
2011-11-16 8:31 ` Rafal Prylowski
2011-11-19 12:38 ` Mika Westerberg
2011-11-19 12:38 ` Mika Westerberg
2011-11-21 7:44 ` Rafal Prylowski
2011-11-21 7:44 ` Rafal Prylowski
2011-11-21 8:01 ` Mika Westerberg
2011-11-21 8:01 ` Mika Westerberg
2011-11-21 8:32 ` Vinod Koul
2011-11-21 8:32 ` Vinod Koul
2011-11-22 5:59 ` Mika Westerberg
2011-11-22 5:59 ` Mika Westerberg
2011-11-23 10:47 ` Vinod Koul
2011-11-23 10:47 ` Vinod Koul
2011-11-21 8:54 ` Rafal Prylowski
2011-11-21 8:54 ` Rafal Prylowski
2011-11-22 6:47 ` Mika Westerberg
2011-11-22 6:47 ` Mika Westerberg
2011-11-22 8:45 ` Rafal Prylowski
2011-11-22 8:45 ` Rafal Prylowski
2011-05-29 10:10 ` [PATCH v2 2/5] ep93xx: add dmaengine platform code Mika Westerberg
2011-05-29 10:10 ` Mika Westerberg
2011-05-29 10:10 ` [PATCH v2 3/5] ASoC: ep93xx: convert to use the DMA engine API Mika Westerberg
2011-05-29 10:10 ` Mika Westerberg
2011-05-29 10:10 ` [PATCH v2 4/5] ep93xx: remove the old M2P DMA code Mika Westerberg
2011-05-29 10:10 ` Mika Westerberg
2011-05-29 10:10 ` [PATCH v2 5/5] spi/ep93xx: add DMA support Mika Westerberg
2011-05-29 10:10 ` Mika Westerberg
2011-06-03 20:44 ` Grant Likely
2011-06-03 20:44 ` Grant Likely
2011-06-07 17:14 ` Mika Westerberg
2011-06-07 17:14 ` Mika Westerberg
2011-06-07 18:45 ` Grant Likely
2011-06-07 18:45 ` Grant Likely
2011-06-07 19:06 ` Mika Westerberg
2011-06-07 19:06 ` Mika Westerberg
2011-06-07 19:18 ` Grant Likely
2011-06-07 19:18 ` Grant Likely
2011-06-07 19:29 ` Mika Westerberg
2011-06-07 19:29 ` Mika Westerberg
2011-06-07 19:40 ` Grant Likely
2011-06-07 19:40 ` Grant Likely
2011-06-08 3:58 ` Koul, Vinod
2011-06-08 3:58 ` Koul, Vinod
2011-06-08 21:53 ` Grant Likely
2011-06-08 21:53 ` Grant Likely
2011-06-09 16:42 ` Koul, Vinod
2011-06-09 16:42 ` Koul, Vinod
2011-06-09 18:46 ` Grant Likely
2011-06-09 18:46 ` Grant Likely
2011-06-09 19:15 ` Mika Westerberg
2011-06-09 19:15 ` Mika Westerberg
2011-06-05 8:19 ` [PATCH v2 0/5] ep93xx DMA patches Mika Westerberg
2011-06-05 8:19 ` Mika Westerberg
2011-06-06 6:39 ` Koul, Vinod
2011-06-06 6:39 ` Koul, Vinod
2011-06-06 16:42 ` Mika Westerberg
2011-06-06 16:42 ` Mika Westerberg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4EC374F0.8000400@metasoft.pl \
--to=prylowski@metasoft.pl \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.