* [U-Boot] [PATCH V4] i.MX6: mx6q_sabrelite: add SATA bindings [not found] <http://lists.denx.de/pipermail/u-boot/2012-April/#123169> @ 2012-05-01 19:24 ` Eric Nelson 2012-05-01 19:25 ` Marek Vasut 2012-05-01 19:55 ` [U-Boot] [PATCH V5] " Eric Nelson 1 sibling, 1 reply; 10+ messages in thread From: Eric Nelson @ 2012-05-01 19:24 UTC (permalink / raw) To: u-boot Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> --- V2 has been stripped of the board-independent changes and uses clrsetbits_le32() instead of twiddling bits by hand. V3 returns immediately from setup_sata() if enable_sata_clock() returns an error. V4 removes extra #include and addresses a style issue as discussed on the ML. board/freescale/mx6qsabrelite/mx6qsabrelite.c | 31 +++++++++++++++++++++++++ include/configs/mx6qsabrelite.h | 13 ++++++++++ 2 files changed, 44 insertions(+), 0 deletions(-) diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c index 1d09a72..cdd2f15 100644 --- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c +++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c @@ -25,6 +25,7 @@ #include <asm/arch/imx-regs.h> #include <asm/arch/mx6x_pins.h> #include <asm/arch/iomux-v3.h> +#include <asm/arch/clock.h> #include <asm/errno.h> #include <asm/gpio.h> #include <mmc.h> @@ -267,6 +268,32 @@ int board_eth_init(bd_t *bis) return 0; } +#ifdef CONFIG_CMD_SATA + +int setup_sata(void) +{ + struct iomuxc_base_regs *const iomuxc_regs + = (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR; + int ret = enable_sata_clock(); + if (ret) + return ret; + + clrsetbits_le32(&iomuxc_regs->gpr[13], + IOMUXC_GPR13_SATA_MASK, + IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB + |IOMUXC_GPR13_SATA_PHY_7_SATA2M + |IOMUXC_GPR13_SATA_SPEED_3G + |(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT) + |IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED + |IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16 + |IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB + |IOMUXC_GPR13_SATA_PHY_2_TX_1P104V + |IOMUXC_GPR13_SATA_PHY_1_SLOW); + + return 0 ; +} +#endif + int board_early_init_f(void) { setup_iomux_uart(); @@ -283,6 +310,10 @@ int board_init(void) setup_spi(); #endif +#ifdef CONFIG_CMD_SATA + setup_sata(); +#endif + return 0; } diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h index f52c3c7..1d92dd0 100644 --- a/include/configs/mx6qsabrelite.h +++ b/include/configs/mx6qsabrelite.h @@ -71,6 +71,19 @@ #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION +#define CONFIG_CMD_SATA +/* + * SATA Configs + */ +#ifdef CONFIG_CMD_SATA +#define CONFIG_DWC_AHSATA +#define CONFIG_SYS_SATA_MAX_DEVICE 1 +#define CONFIG_DWC_AHSATA_PORT_ID 0 +#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR +#define CONFIG_LBA48 +#define CONFIG_LIBATA +#endif + #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_MII -- 1.7.9 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH V4] i.MX6: mx6q_sabrelite: add SATA bindings 2012-05-01 19:24 ` [U-Boot] [PATCH V4] i.MX6: mx6q_sabrelite: add SATA bindings Eric Nelson @ 2012-05-01 19:25 ` Marek Vasut 2012-05-01 19:53 ` Eric Nelson 0 siblings, 1 reply; 10+ messages in thread From: Marek Vasut @ 2012-05-01 19:25 UTC (permalink / raw) To: u-boot Dear Eric Nelson, > Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> > --- > V2 has been stripped of the board-independent changes and > uses clrsetbits_le32() instead of twiddling bits by hand. > > V3 returns immediately from setup_sata() if enable_sata_clock() > returns an error. > > V4 removes extra #include and addresses a style issue as discussed > on the ML. It's still there ;-) > > board/freescale/mx6qsabrelite/mx6qsabrelite.c | 31 > +++++++++++++++++++++++++ include/configs/mx6qsabrelite.h | > 13 ++++++++++ > 2 files changed, 44 insertions(+), 0 deletions(-) > > diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c > b/board/freescale/mx6qsabrelite/mx6qsabrelite.c index 1d09a72..cdd2f15 > 100644 > --- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c > +++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c > @@ -25,6 +25,7 @@ > #include <asm/arch/imx-regs.h> > #include <asm/arch/mx6x_pins.h> > #include <asm/arch/iomux-v3.h> > +#include <asm/arch/clock.h> > #include <asm/errno.h> > #include <asm/gpio.h> > #include <mmc.h> > @@ -267,6 +268,32 @@ int board_eth_init(bd_t *bis) > return 0; > } > > +#ifdef CONFIG_CMD_SATA > + > +int setup_sata(void) > +{ > + struct iomuxc_base_regs *const iomuxc_regs > + = (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR; > + int ret = enable_sata_clock(); > + if (ret) > + return ret; > + > + clrsetbits_le32(&iomuxc_regs->gpr[13], > + IOMUXC_GPR13_SATA_MASK, > + IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB > + |IOMUXC_GPR13_SATA_PHY_7_SATA2M > + |IOMUXC_GPR13_SATA_SPEED_3G > + |(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT) > + |IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED > + |IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16 > + |IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB > + |IOMUXC_GPR13_SATA_PHY_2_TX_1P104V > + |IOMUXC_GPR13_SATA_PHY_1_SLOW); > + > + return 0 ; <---- here :-) > +} > +#endif > + > int board_early_init_f(void) > { > setup_iomux_uart(); > @@ -283,6 +310,10 @@ int board_init(void) > setup_spi(); > #endif > > +#ifdef CONFIG_CMD_SATA > + setup_sata(); > +#endif > + > return 0; > } > > diff --git a/include/configs/mx6qsabrelite.h > b/include/configs/mx6qsabrelite.h index f52c3c7..1d92dd0 100644 > --- a/include/configs/mx6qsabrelite.h > +++ b/include/configs/mx6qsabrelite.h > @@ -71,6 +71,19 @@ > #define CONFIG_CMD_FAT > #define CONFIG_DOS_PARTITION > > +#define CONFIG_CMD_SATA > +/* > + * SATA Configs > + */ > +#ifdef CONFIG_CMD_SATA > +#define CONFIG_DWC_AHSATA > +#define CONFIG_SYS_SATA_MAX_DEVICE 1 > +#define CONFIG_DWC_AHSATA_PORT_ID 0 > +#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR > +#define CONFIG_LBA48 > +#define CONFIG_LIBATA > +#endif > + > #define CONFIG_CMD_PING > #define CONFIG_CMD_DHCP > #define CONFIG_CMD_MII ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH V4] i.MX6: mx6q_sabrelite: add SATA bindings 2012-05-01 19:25 ` Marek Vasut @ 2012-05-01 19:53 ` Eric Nelson 2012-05-01 21:11 ` Marek Vasut 0 siblings, 1 reply; 10+ messages in thread From: Eric Nelson @ 2012-05-01 19:53 UTC (permalink / raw) To: u-boot On 05/01/2012 12:25 PM, Marek Vasut wrote: > Dear Eric Nelson, > >> Signed-off-by: Eric Nelson<eric.nelson@boundarydevices.com> >> --- >> V2 has been stripped of the board-independent changes and >> uses clrsetbits_le32() instead of twiddling bits by hand. >> >> V3 returns immediately from setup_sata() if enable_sata_clock() >> returns an error. >> >> V4 removes extra #include and addresses a style issue as discussed >> on the ML. > > It's still there ;-) >> >> <snip> >> >> + |IOMUXC_GPR13_SATA_PHY_2_TX_1P104V >> + |IOMUXC_GPR13_SATA_PHY_1_SLOW); >> + > >> + return 0 ;<---- here :-) > My eyes are clearly not as finely tuned as yours... <thought to self> What are the odd that I could tweak checkpatch.pl without introducing another style issue? </thought to self> V5 forthcoming... ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH V4] i.MX6: mx6q_sabrelite: add SATA bindings 2012-05-01 19:53 ` Eric Nelson @ 2012-05-01 21:11 ` Marek Vasut 2012-05-01 21:58 ` Eric Nelson 0 siblings, 1 reply; 10+ messages in thread From: Marek Vasut @ 2012-05-01 21:11 UTC (permalink / raw) To: u-boot Dear Eric Nelson, > On 05/01/2012 12:25 PM, Marek Vasut wrote: > > Dear Eric Nelson, > > > >> Signed-off-by: Eric Nelson<eric.nelson@boundarydevices.com> > >> --- > >> V2 has been stripped of the board-independent changes and > >> uses clrsetbits_le32() instead of twiddling bits by hand. > >> > >> V3 returns immediately from setup_sata() if enable_sata_clock() > >> returns an error. > >> > >> V4 removes extra #include and addresses a style issue as discussed > >> on the ML. > > > > It's still there ;-) > > > >> <snip> > >> > >> + |IOMUXC_GPR13_SATA_PHY_2_TX_1P104V > >> + |IOMUXC_GPR13_SATA_PHY_1_SLOW); > >> + > >> > >> + return 0 ;<---- here :-) > > My eyes are clearly not as finely tuned as yours... 1 dioptry on left eye, lazy-eye blindness on the right one ;-) > <thought to self> > What are the odd that I could tweak checkpatch.pl > without introducing another style issue? > </thought to self> That'd be awesome. > V5 forthcoming... Thanks :) Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH V4] i.MX6: mx6q_sabrelite: add SATA bindings 2012-05-01 21:11 ` Marek Vasut @ 2012-05-01 21:58 ` Eric Nelson 0 siblings, 0 replies; 10+ messages in thread From: Eric Nelson @ 2012-05-01 21:58 UTC (permalink / raw) To: u-boot On 05/01/2012 02:11 PM, Marek Vasut wrote: > Dear Eric Nelson, > >> On 05/01/2012 12:25 PM, Marek Vasut wrote: >>> Dear Eric Nelson, >>> >>>> Signed-off-by: Eric Nelson<eric.nelson@boundarydevices.com> >>>> --- >>>> V2 has been stripped of the board-independent changes and >>>> uses clrsetbits_le32() instead of twiddling bits by hand. >>>> >>>> V3 returns immediately from setup_sata() if enable_sata_clock() >>>> returns an error. >>>> >>>> V4 removes extra #include and addresses a style issue as discussed >>>> on the ML. >>> >>> It's still there ;-) >>> >> >> <snip> >>>> >>>> + |IOMUXC_GPR13_SATA_PHY_2_TX_1P104V >>>> + |IOMUXC_GPR13_SATA_PHY_1_SLOW); >>>> + >>>> >>>> + return 0 ;<---- here :-) >> >> My eyes are clearly not as finely tuned as yours... > > 1 dioptry on left eye, lazy-eye blindness on the right one ;-) > For all that, you seem to see quite well! >> <thought to self> >> What are the odd that I could tweak checkpatch.pl >> without introducing another style issue? >> </thought to self> > > That'd be awesome. > Forthcoming... ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH V5] i.MX6: mx6q_sabrelite: add SATA bindings [not found] <http://lists.denx.de/pipermail/u-boot/2012-April/#123169> 2012-05-01 19:24 ` [U-Boot] [PATCH V4] i.MX6: mx6q_sabrelite: add SATA bindings Eric Nelson @ 2012-05-01 19:55 ` Eric Nelson 2012-05-01 20:09 ` Marek Vasut ` (2 more replies) 1 sibling, 3 replies; 10+ messages in thread From: Eric Nelson @ 2012-05-01 19:55 UTC (permalink / raw) To: u-boot Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> --- V2 has been stripped of the board-independent changes and uses clrsetbits_le32() instead of twiddling bits by hand. V3 returns immediately from setup_sata() if enable_sata_clock() returns an error. V4 removes extra #include and addresses a style issue as discussed on the ML. V5 addresses another (hopefully last) style issue. board/freescale/mx6qsabrelite/mx6qsabrelite.c | 31 +++++++++++++++++++++++++ include/configs/mx6qsabrelite.h | 13 ++++++++++ 2 files changed, 44 insertions(+), 0 deletions(-) diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c index 1d09a72..cdd2f15 100644 --- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c +++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c @@ -25,6 +25,7 @@ #include <asm/arch/imx-regs.h> #include <asm/arch/mx6x_pins.h> #include <asm/arch/iomux-v3.h> +#include <asm/arch/clock.h> #include <asm/errno.h> #include <asm/gpio.h> #include <mmc.h> @@ -267,6 +268,32 @@ int board_eth_init(bd_t *bis) return 0; } +#ifdef CONFIG_CMD_SATA + +int setup_sata(void) +{ + struct iomuxc_base_regs *const iomuxc_regs + = (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR; + int ret = enable_sata_clock(); + if (ret) + return ret; + + clrsetbits_le32(&iomuxc_regs->gpr[13], + IOMUXC_GPR13_SATA_MASK, + IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB + |IOMUXC_GPR13_SATA_PHY_7_SATA2M + |IOMUXC_GPR13_SATA_SPEED_3G + |(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT) + |IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED + |IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16 + |IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB + |IOMUXC_GPR13_SATA_PHY_2_TX_1P104V + |IOMUXC_GPR13_SATA_PHY_1_SLOW); + + return 0; +} +#endif + int board_early_init_f(void) { setup_iomux_uart(); @@ -283,6 +310,10 @@ int board_init(void) setup_spi(); #endif +#ifdef CONFIG_CMD_SATA + setup_sata(); +#endif + return 0; } diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h index f52c3c7..1d92dd0 100644 --- a/include/configs/mx6qsabrelite.h +++ b/include/configs/mx6qsabrelite.h @@ -71,6 +71,19 @@ #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION +#define CONFIG_CMD_SATA +/* + * SATA Configs + */ +#ifdef CONFIG_CMD_SATA +#define CONFIG_DWC_AHSATA +#define CONFIG_SYS_SATA_MAX_DEVICE 1 +#define CONFIG_DWC_AHSATA_PORT_ID 0 +#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR +#define CONFIG_LBA48 +#define CONFIG_LIBATA +#endif + #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_MII -- 1.7.9 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH V5] i.MX6: mx6q_sabrelite: add SATA bindings 2012-05-01 19:55 ` [U-Boot] [PATCH V5] " Eric Nelson @ 2012-05-01 20:09 ` Marek Vasut 2012-05-01 20:23 ` Eric Nelson 2012-05-06 17:06 ` Stefano Babic 2012-05-06 17:10 ` Stefano Babic 2 siblings, 1 reply; 10+ messages in thread From: Marek Vasut @ 2012-05-01 20:09 UTC (permalink / raw) To: u-boot Dear Eric Nelson, > Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> > --- > V2 has been stripped of the board-independent changes and > uses clrsetbits_le32() instead of twiddling bits by hand. > > V3 returns immediately from setup_sata() if enable_sata_clock() > returns an error. > > V4 removes extra #include and addresses a style issue as discussed > on the ML. > > V5 addresses another (hopefully last) style issue. Sorry for torturing you so much :-) Acked-by: Marek Vasut <marex@denx.de> > > board/freescale/mx6qsabrelite/mx6qsabrelite.c | 31 > +++++++++++++++++++++++++ include/configs/mx6qsabrelite.h | > 13 ++++++++++ > 2 files changed, 44 insertions(+), 0 deletions(-) > > diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c > b/board/freescale/mx6qsabrelite/mx6qsabrelite.c index 1d09a72..cdd2f15 > 100644 > --- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c > +++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c > @@ -25,6 +25,7 @@ > #include <asm/arch/imx-regs.h> > #include <asm/arch/mx6x_pins.h> > #include <asm/arch/iomux-v3.h> > +#include <asm/arch/clock.h> > #include <asm/errno.h> > #include <asm/gpio.h> > #include <mmc.h> > @@ -267,6 +268,32 @@ int board_eth_init(bd_t *bis) > return 0; > } > > +#ifdef CONFIG_CMD_SATA > + > +int setup_sata(void) > +{ > + struct iomuxc_base_regs *const iomuxc_regs > + = (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR; > + int ret = enable_sata_clock(); > + if (ret) > + return ret; > + > + clrsetbits_le32(&iomuxc_regs->gpr[13], > + IOMUXC_GPR13_SATA_MASK, > + IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB > + |IOMUXC_GPR13_SATA_PHY_7_SATA2M > + |IOMUXC_GPR13_SATA_SPEED_3G > + |(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT) > + |IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED > + |IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16 > + |IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB > + |IOMUXC_GPR13_SATA_PHY_2_TX_1P104V > + |IOMUXC_GPR13_SATA_PHY_1_SLOW); > + > + return 0; > +} > +#endif > + > int board_early_init_f(void) > { > setup_iomux_uart(); > @@ -283,6 +310,10 @@ int board_init(void) > setup_spi(); > #endif > > +#ifdef CONFIG_CMD_SATA > + setup_sata(); > +#endif > + > return 0; > } > > diff --git a/include/configs/mx6qsabrelite.h > b/include/configs/mx6qsabrelite.h index f52c3c7..1d92dd0 100644 > --- a/include/configs/mx6qsabrelite.h > +++ b/include/configs/mx6qsabrelite.h > @@ -71,6 +71,19 @@ > #define CONFIG_CMD_FAT > #define CONFIG_DOS_PARTITION > > +#define CONFIG_CMD_SATA > +/* > + * SATA Configs > + */ > +#ifdef CONFIG_CMD_SATA > +#define CONFIG_DWC_AHSATA > +#define CONFIG_SYS_SATA_MAX_DEVICE 1 > +#define CONFIG_DWC_AHSATA_PORT_ID 0 > +#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR > +#define CONFIG_LBA48 > +#define CONFIG_LIBATA > +#endif > + > #define CONFIG_CMD_PING > #define CONFIG_CMD_DHCP > #define CONFIG_CMD_MII ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH V5] i.MX6: mx6q_sabrelite: add SATA bindings 2012-05-01 20:09 ` Marek Vasut @ 2012-05-01 20:23 ` Eric Nelson 0 siblings, 0 replies; 10+ messages in thread From: Eric Nelson @ 2012-05-01 20:23 UTC (permalink / raw) To: u-boot On 05/01/2012 01:09 PM, Marek Vasut wrote: > Dear Eric Nelson, > >> Signed-off-by: Eric Nelson<eric.nelson@boundarydevices.com> >> --- >> V2 has been stripped of the board-independent changes and >> uses clrsetbits_le32() instead of twiddling bits by hand. >> >> V3 returns immediately from setup_sata() if enable_sata_clock() >> returns an error. >> >> V4 removes extra #include and addresses a style issue as discussed >> on the ML. >> >> V5 addresses another (hopefully last) style issue. > > Sorry for torturing you so much :-) > No worries. I think I have a high threshold... > Acked-by: Marek Vasut<marex@denx.de> > Thanks for the ack. ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH V5] i.MX6: mx6q_sabrelite: add SATA bindings 2012-05-01 19:55 ` [U-Boot] [PATCH V5] " Eric Nelson 2012-05-01 20:09 ` Marek Vasut @ 2012-05-06 17:06 ` Stefano Babic 2012-05-06 17:10 ` Stefano Babic 2 siblings, 0 replies; 10+ messages in thread From: Stefano Babic @ 2012-05-06 17:06 UTC (permalink / raw) To: u-boot On 01/05/2012 21:55, Eric Nelson wrote: > Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> > --- > V2 has been stripped of the board-independent changes and > uses clrsetbits_le32() instead of twiddling bits by hand. > > V3 returns immediately from setup_sata() if enable_sata_clock() > returns an error. > > V4 removes extra #include and addresses a style issue as discussed > on the ML. > > V5 addresses another (hopefully last) style issue. > > board/freescale/mx6qsabrelite/mx6qsabrelite.c | 31 +++++++++++++++++++++++++ > include/configs/mx6qsabrelite.h | 13 ++++++++++ > 2 files changed, 44 insertions(+), 0 deletions(-) > > diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c > index 1d09a72..cdd2f15 100644 > --- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c > +++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c > @@ -25,6 +25,7 @@ > #include <asm/arch/imx-regs.h> > #include <asm/arch/mx6x_pins.h> > #include <asm/arch/iomux-v3.h> > +#include <asm/arch/clock.h> > #include <asm/errno.h> > #include <asm/gpio.h> > #include <mmc.h> > @@ -267,6 +268,32 @@ int board_eth_init(bd_t *bis) > return 0; > } > > +#ifdef CONFIG_CMD_SATA > + > +int setup_sata(void) > +{ > + struct iomuxc_base_regs *const iomuxc_regs > + = (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR; > + int ret = enable_sata_clock(); > + if (ret) > + return ret; > + > + clrsetbits_le32(&iomuxc_regs->gpr[13], > + IOMUXC_GPR13_SATA_MASK, > + IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB > + |IOMUXC_GPR13_SATA_PHY_7_SATA2M > + |IOMUXC_GPR13_SATA_SPEED_3G > + |(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT) > + |IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED > + |IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16 > + |IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB > + |IOMUXC_GPR13_SATA_PHY_2_TX_1P104V > + |IOMUXC_GPR13_SATA_PHY_1_SLOW); > + > + return 0; > +} > +#endif > + > int board_early_init_f(void) > { > setup_iomux_uart(); > @@ -283,6 +310,10 @@ int board_init(void) > setup_spi(); > #endif > > +#ifdef CONFIG_CMD_SATA > + setup_sata(); > +#endif > + > return 0; > } > > diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h > index f52c3c7..1d92dd0 100644 > --- a/include/configs/mx6qsabrelite.h > +++ b/include/configs/mx6qsabrelite.h > @@ -71,6 +71,19 @@ > #define CONFIG_CMD_FAT > #define CONFIG_DOS_PARTITION > > +#define CONFIG_CMD_SATA > +/* > + * SATA Configs > + */ > +#ifdef CONFIG_CMD_SATA > +#define CONFIG_DWC_AHSATA > +#define CONFIG_SYS_SATA_MAX_DEVICE 1 > +#define CONFIG_DWC_AHSATA_PORT_ID 0 > +#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR > +#define CONFIG_LBA48 > +#define CONFIG_LIBATA > +#endif > + > #define CONFIG_CMD_PING > #define CONFIG_CMD_DHCP > #define CONFIG_CMD_MII Acked-by: stefano Babic <sbabic@denx.de> Best regards, Stefano Babic -- ===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de ===================================================================== ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH V5] i.MX6: mx6q_sabrelite: add SATA bindings 2012-05-01 19:55 ` [U-Boot] [PATCH V5] " Eric Nelson 2012-05-01 20:09 ` Marek Vasut 2012-05-06 17:06 ` Stefano Babic @ 2012-05-06 17:10 ` Stefano Babic 2 siblings, 0 replies; 10+ messages in thread From: Stefano Babic @ 2012-05-06 17:10 UTC (permalink / raw) To: u-boot On 01/05/2012 21:55, Eric Nelson wrote: > Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> > --- > V2 has been stripped of the board-independent changes and > uses clrsetbits_le32() instead of twiddling bits by hand. > > V3 returns immediately from setup_sata() if enable_sata_clock() > returns an error. > > V4 removes extra #include and addresses a style issue as discussed > on the ML. > > V5 addresses another (hopefully last) style issue. > Hi Eric, applied after rebasing on current u-boot-imx. Best regards, Stefano Babic -- ===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de ===================================================================== ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2012-05-06 17:10 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <http://lists.denx.de/pipermail/u-boot/2012-April/#123169>
2012-05-01 19:24 ` [U-Boot] [PATCH V4] i.MX6: mx6q_sabrelite: add SATA bindings Eric Nelson
2012-05-01 19:25 ` Marek Vasut
2012-05-01 19:53 ` Eric Nelson
2012-05-01 21:11 ` Marek Vasut
2012-05-01 21:58 ` Eric Nelson
2012-05-01 19:55 ` [U-Boot] [PATCH V5] " Eric Nelson
2012-05-01 20:09 ` Marek Vasut
2012-05-01 20:23 ` Eric Nelson
2012-05-06 17:06 ` Stefano Babic
2012-05-06 17:10 ` Stefano Babic
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.