From: Oliver Schinagl <oliver+list@schinagl.nl>
To: Jan Saris <jan.saris@gmail.com>
Cc: linux-media@vger.kernel.org
Subject: Re: No Signal with TerraTec Cinergy T PCIe dual
Date: Sun, 07 Apr 2013 17:42:55 +0200 [thread overview]
Message-ID: <516193FF.50709@schinagl.nl> (raw)
In-Reply-To: <CAK2FuSnQxgc2hvtgb=COH0BGaJVqY5Cg=4fYWpB_BwOn8TYE_w@mail.gmail.com>
On 07-04-13 12:56, Jan Saris wrote:
> Hi,
>
> Sinse a couple of months I'm trying to get my second DVB-C card to
> work, but with no luck.
> I have searched a lot around and even tried the last media_build.
I have the same card and while I don't see anything wrong (you have 2
dvb-t devices installed right? adapter0 is something else, and the
Cinergy is adapter1 and adapter2? Ah, yes you do say 'other dvb-c' sorry.
> I am running linux 3.5.0-26-generic with the latests media_build from
> here (http://git.linuxtv.org/media_build.git)
>
> For some reason the card won't get a lock. Here are my test results:
Remember to set the frontend properly; dvb-fe-tool from memory (tab
completion ftw). And remember the cinergy is dual dvb-t; but only single
dvb-c (and single analog, but i think that is still not implemented?)
>
> Terratec Cinergy PCIe Dual
> dvbv5-scan -a2 -v channel2.conf
> using demux '/dev/dvb/adapter2/demux0'
> Device DRXK DVB-C DVB-T (/dev/dvb/adapter2/frontend0) capabilities:
> CAN_FEC_1_2 CAN_FEC_2_3 CAN_FEC_3_4 CAN_FEC_5_6 CAN_FEC_7_8
> CAN_FEC_AUTO CAN_GUARD_INTERVAL_AUTO CAN_HIERARCHY_AUTO
> CAN_INVERSION_AUTO CAN_MUTE_TS CAN_QAM_16 CAN_QAM_32 CAN_QAM_64
> CAN_QAM_128 CAN_QAM_256 CAN_RECOVER CAN_TRANSMISSION_MODE_AUTO
> DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
> Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C DVBT
> Scanning frequency #1 304000000
> FREQUENCY = 304000000
> MODULATION = QAM/64
> INVERSION = AUTO
> SYMBOL_RATE = 6875000
> INNER_FEC = AUTO
> DELIVERY_SYSTEM = DVBC/ANNEX_A
> status 00 | signal 0% | snr 0% | ber 0 | unc 119 | tune failed
> dmesg
> [ 5.332360] cx23885_dvb_register() allocating 1 frontend(s)
> [ 5.332365] cx23885[0]: cx23885 based dvb card
> [ 5.365162] drxk: status = 0x639160d9
> [ 5.365167] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz
> [ 5.465869] DRXK driver version 0.9.4300
> [ 5.504139] drxk: frontend initialized.
> [ 5.517782] mt2063_attach: Attaching MT2063
> [ 5.517788] DVB: registering new adapter (cx23885[0])
> [ 5.517791] DVB: registering adapter 1 frontend 0 (DRXK DVB-T)...
> [ 5.518664] cx23885_dvb_register() allocating 1 frontend(s)
> [ 5.518668] cx23885[0]: cx23885 based dvb card
> [ 5.533886] drxk: status = 0x639130d9
> [ 5.533896] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz
> [ 5.617338] DRXK driver version 0.9.4300
> [ 5.650861] drxk: frontend initialized.
> [ 5.650872] mt2063_attach: Attaching MT2063
> [ 5.650876] DVB: registering new adapter (cx23885[0])
> [ 5.650878] DVB: registering adapter 2 frontend 0 (DRXK DVB-C DVB-T)...
> [ 5.651338] cx23885_dev_checkrevision() Hardware revision = 0xa5
> [ 5.651343] cx23885[0]/0: found at 0000:02:00.0, rev: 4, irq: 16,
> latency: 0, mmio: 0xff400000
> ........
> [ 153.727978] mt2063: detected a mt2063 B3
> [ 153.877050] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 153.877058] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
> [ 156.989702] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 156.989710] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
> [ 170.558420] mt2063: detected a mt2063 B3
> [ 170.629422] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 170.629430] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
> [ 173.742057] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 173.742065] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
> [ 251.314900] mt2063: detected a mt2063 B3
> [ 251.385932] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 251.385940] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
> [ 254.498522] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 254.498530] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
>
> lspci -vvv
> 02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885
> PCI Video and Audio Decoder (rev 04)
> Subsystem: TERRATEC Electronic GmbH Cinergy T PCIe Dual
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at ff400000 (64-bit, non-prefetchable) [size=2M]
> Capabilities: [40] Express (v1) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1 <1us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0 <2us, L1 <4us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive- BWMgmt- ABWMgmt-
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [90] Vital Product Data
> Product Name: "
> End
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
> Capabilities: [200 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed+ WRR32+ WRR64+ WRR128-
> Ctrl: ArbSelect=WRR64
> Status: InProgress-
> Port Arbitration Table [240] <?>
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
> Status: NegoPending- InProgress-
> Kernel driver in use: cx23885
> Kernel modules: cx23885
>
> It says no signal, but if I put the antenna-cable in my other DVB-C
> card and do a scan I get:
> Philips TV-Card
> dvbv5-scan -a0 -v channel2.conf
> using demux '/dev/dvb/adapter0/demux0'
> Device Philips TDA10023 DVB-C (/dev/dvb/adapter0/frontend0) capabilities:
> CAN_FEC_AUTO CAN_INVERSION_AUTO CAN_QAM_16 CAN_QAM_32
> CAN_QAM_64 CAN_QAM_128 CAN_QAM_256 CAN_QPSK
> DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
> Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C
> Scanning frequency #1 304000000
> FREQUENCY = 304000000
> MODULATION = QAM/64
> INVERSION = AUTO
> SYMBOL_RATE = 6875000
> INNER_FEC = AUTO
> DELIVERY_SYSTEM = DVBC/ANNEX_A
> status 1f | signal 97% | snr 94% | ber 1728 | unc 62194 | FE_HAS_LOCK
>
> Service #0 (101) Nederland 1 channel 0.1.0
> Service #1 (102) Nederland 2 channel 0.2.1
> Service #2 (103) Nederland 3 channel 0.3.2
> Service #3 (8101) 100%NL channel 0.801.3
> Service #4 (8102) Arrow Classic Rock channel 0.802.4
> Service #5 (8103) Arrow Jazz channel 0.803.5
> Service #6 (8104) BBC radio 1 channel 0.804.6
> Service #7 (8105) BBC radio 2 channel 0.805.7
> Service #8 (8106) BBC radio 3 channel 0.806.8
> Service #9 (8107) BBC radio 4 channel 0.807.9
> Service #10 (8108) BNR channel 0.808.10
> Service #11 (8109) Classic FM channel 0.809.11
> New transponder/channel found: #2: 505937920
> New transponder/channel found: #3: 515112960
> New transponder/channel found: #4: 524288000
> New transponder/channel found: #5: 529530880
> New transponder/channel found: #6: 538705920
> New transponder/channel found: #7: 547880960
> New transponder/channel found: #8: 557056000
> New transponder/channel found: #9: 566231040
> New transponder/channel found: #10: 312000000
> New transponder/channel found: #11: 320000000
> New transponder/channel found: #12: 328000000
> New transponder/channel found: #13: 336000000
> New transponder/channel found: #14: 580648960
> New transponder/channel found: #15: 344000000
> New transponder/channel found: #16: 352000000
> New transponder/channel found: #17: 360000000
> New transponder/channel found: #18: 368000000
>
> Does anyone know what I'm doing wrong?
> Thanks,
>
> Jan Saris
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2013-04-08 7:13 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-04-07 10:56 No Signal with TerraTec Cinergy T PCIe dual Jan Saris
2013-04-07 15:42 ` Oliver Schinagl [this message]
2013-04-09 8:47 ` Jan Saris
2013-04-08 17:58 ` Oliver Schinagl
2013-04-09 9:31 ` Cédric Girard
-- strict thread matches above, loose matches on Subject: below --
2013-01-08 21:02 Cédric Girard
2013-01-08 21:46 ` Antti Palosaari
2013-01-08 22:10 ` Cédric Girard
2013-03-06 14:28 ` Cédric Girard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=516193FF.50709@schinagl.nl \
--to=oliver+list@schinagl.nl \
--cc=jan.saris@gmail.com \
--cc=linux-media@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.