* No Signal with TerraTec Cinergy T PCIe dual
@ 2013-04-07 10:56 Jan Saris
2013-04-07 15:42 ` Oliver Schinagl
0 siblings, 1 reply; 9+ messages in thread
From: Jan Saris @ 2013-04-07 10:56 UTC (permalink / raw)
To: linux-media
Hi,
Sinse a couple of months I'm trying to get my second DVB-C card to
work, but with no luck.
I have searched a lot around and even tried the last media_build.
I am running linux 3.5.0-26-generic with the latests media_build from
here (http://git.linuxtv.org/media_build.git)
For some reason the card won't get a lock. Here are my test results:
Terratec Cinergy PCIe Dual
dvbv5-scan -a2 -v channel2.conf
using demux '/dev/dvb/adapter2/demux0'
Device DRXK DVB-C DVB-T (/dev/dvb/adapter2/frontend0) capabilities:
CAN_FEC_1_2 CAN_FEC_2_3 CAN_FEC_3_4 CAN_FEC_5_6 CAN_FEC_7_8
CAN_FEC_AUTO CAN_GUARD_INTERVAL_AUTO CAN_HIERARCHY_AUTO
CAN_INVERSION_AUTO CAN_MUTE_TS CAN_QAM_16 CAN_QAM_32 CAN_QAM_64
CAN_QAM_128 CAN_QAM_256 CAN_RECOVER CAN_TRANSMISSION_MODE_AUTO
DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C DVBT
Scanning frequency #1 304000000
FREQUENCY = 304000000
MODULATION = QAM/64
INVERSION = AUTO
SYMBOL_RATE = 6875000
INNER_FEC = AUTO
DELIVERY_SYSTEM = DVBC/ANNEX_A
status 00 | signal 0% | snr 0% | ber 0 | unc 119 | tune failed
dmesg
[ 5.332360] cx23885_dvb_register() allocating 1 frontend(s)
[ 5.332365] cx23885[0]: cx23885 based dvb card
[ 5.365162] drxk: status = 0x639160d9
[ 5.365167] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz
[ 5.465869] DRXK driver version 0.9.4300
[ 5.504139] drxk: frontend initialized.
[ 5.517782] mt2063_attach: Attaching MT2063
[ 5.517788] DVB: registering new adapter (cx23885[0])
[ 5.517791] DVB: registering adapter 1 frontend 0 (DRXK DVB-T)...
[ 5.518664] cx23885_dvb_register() allocating 1 frontend(s)
[ 5.518668] cx23885[0]: cx23885 based dvb card
[ 5.533886] drxk: status = 0x639130d9
[ 5.533896] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz
[ 5.617338] DRXK driver version 0.9.4300
[ 5.650861] drxk: frontend initialized.
[ 5.650872] mt2063_attach: Attaching MT2063
[ 5.650876] DVB: registering new adapter (cx23885[0])
[ 5.650878] DVB: registering adapter 2 frontend 0 (DRXK DVB-C DVB-T)...
[ 5.651338] cx23885_dev_checkrevision() Hardware revision = 0xa5
[ 5.651343] cx23885[0]/0: found at 0000:02:00.0, rev: 4, irq: 16,
latency: 0, mmio: 0xff400000
........
[ 153.727978] mt2063: detected a mt2063 B3
[ 153.877050] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 153.877058] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
[ 156.989702] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 156.989710] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
[ 170.558420] mt2063: detected a mt2063 B3
[ 170.629422] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 170.629430] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
[ 173.742057] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 173.742065] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
[ 251.314900] mt2063: detected a mt2063 B3
[ 251.385932] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 251.385940] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
[ 254.498522] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 254.498530] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
lspci -vvv
02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885
PCI Video and Audio Decoder (rev 04)
Subsystem: TERRATEC Electronic GmbH Cinergy T PCIe Dual
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ff400000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [40] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <2us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Vital Product Data
Product Name: "
End
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [200 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32+ WRR64+ WRR128-
Ctrl: ArbSelect=WRR64
Status: InProgress-
Port Arbitration Table [240] <?>
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Kernel driver in use: cx23885
Kernel modules: cx23885
It says no signal, but if I put the antenna-cable in my other DVB-C
card and do a scan I get:
Philips TV-Card
dvbv5-scan -a0 -v channel2.conf
using demux '/dev/dvb/adapter0/demux0'
Device Philips TDA10023 DVB-C (/dev/dvb/adapter0/frontend0) capabilities:
CAN_FEC_AUTO CAN_INVERSION_AUTO CAN_QAM_16 CAN_QAM_32
CAN_QAM_64 CAN_QAM_128 CAN_QAM_256 CAN_QPSK
DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C
Scanning frequency #1 304000000
FREQUENCY = 304000000
MODULATION = QAM/64
INVERSION = AUTO
SYMBOL_RATE = 6875000
INNER_FEC = AUTO
DELIVERY_SYSTEM = DVBC/ANNEX_A
status 1f | signal 97% | snr 94% | ber 1728 | unc 62194 | FE_HAS_LOCK
Service #0 (101) Nederland 1 channel 0.1.0
Service #1 (102) Nederland 2 channel 0.2.1
Service #2 (103) Nederland 3 channel 0.3.2
Service #3 (8101) 100%NL channel 0.801.3
Service #4 (8102) Arrow Classic Rock channel 0.802.4
Service #5 (8103) Arrow Jazz channel 0.803.5
Service #6 (8104) BBC radio 1 channel 0.804.6
Service #7 (8105) BBC radio 2 channel 0.805.7
Service #8 (8106) BBC radio 3 channel 0.806.8
Service #9 (8107) BBC radio 4 channel 0.807.9
Service #10 (8108) BNR channel 0.808.10
Service #11 (8109) Classic FM channel 0.809.11
New transponder/channel found: #2: 505937920
New transponder/channel found: #3: 515112960
New transponder/channel found: #4: 524288000
New transponder/channel found: #5: 529530880
New transponder/channel found: #6: 538705920
New transponder/channel found: #7: 547880960
New transponder/channel found: #8: 557056000
New transponder/channel found: #9: 566231040
New transponder/channel found: #10: 312000000
New transponder/channel found: #11: 320000000
New transponder/channel found: #12: 328000000
New transponder/channel found: #13: 336000000
New transponder/channel found: #14: 580648960
New transponder/channel found: #15: 344000000
New transponder/channel found: #16: 352000000
New transponder/channel found: #17: 360000000
New transponder/channel found: #18: 368000000
Does anyone know what I'm doing wrong?
Thanks,
Jan Saris
^ permalink raw reply [flat|nested] 9+ messages in thread* Re: No Signal with TerraTec Cinergy T PCIe dual
2013-04-07 10:56 No Signal with TerraTec Cinergy T PCIe dual Jan Saris
@ 2013-04-07 15:42 ` Oliver Schinagl
2013-04-09 8:47 ` Jan Saris
0 siblings, 1 reply; 9+ messages in thread
From: Oliver Schinagl @ 2013-04-07 15:42 UTC (permalink / raw)
To: Jan Saris; +Cc: linux-media
On 07-04-13 12:56, Jan Saris wrote:
> Hi,
>
> Sinse a couple of months I'm trying to get my second DVB-C card to
> work, but with no luck.
> I have searched a lot around and even tried the last media_build.
I have the same card and while I don't see anything wrong (you have 2
dvb-t devices installed right? adapter0 is something else, and the
Cinergy is adapter1 and adapter2? Ah, yes you do say 'other dvb-c' sorry.
> I am running linux 3.5.0-26-generic with the latests media_build from
> here (http://git.linuxtv.org/media_build.git)
>
> For some reason the card won't get a lock. Here are my test results:
Remember to set the frontend properly; dvb-fe-tool from memory (tab
completion ftw). And remember the cinergy is dual dvb-t; but only single
dvb-c (and single analog, but i think that is still not implemented?)
>
> Terratec Cinergy PCIe Dual
> dvbv5-scan -a2 -v channel2.conf
> using demux '/dev/dvb/adapter2/demux0'
> Device DRXK DVB-C DVB-T (/dev/dvb/adapter2/frontend0) capabilities:
> CAN_FEC_1_2 CAN_FEC_2_3 CAN_FEC_3_4 CAN_FEC_5_6 CAN_FEC_7_8
> CAN_FEC_AUTO CAN_GUARD_INTERVAL_AUTO CAN_HIERARCHY_AUTO
> CAN_INVERSION_AUTO CAN_MUTE_TS CAN_QAM_16 CAN_QAM_32 CAN_QAM_64
> CAN_QAM_128 CAN_QAM_256 CAN_RECOVER CAN_TRANSMISSION_MODE_AUTO
> DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
> Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C DVBT
> Scanning frequency #1 304000000
> FREQUENCY = 304000000
> MODULATION = QAM/64
> INVERSION = AUTO
> SYMBOL_RATE = 6875000
> INNER_FEC = AUTO
> DELIVERY_SYSTEM = DVBC/ANNEX_A
> status 00 | signal 0% | snr 0% | ber 0 | unc 119 | tune failed
> dmesg
> [ 5.332360] cx23885_dvb_register() allocating 1 frontend(s)
> [ 5.332365] cx23885[0]: cx23885 based dvb card
> [ 5.365162] drxk: status = 0x639160d9
> [ 5.365167] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz
> [ 5.465869] DRXK driver version 0.9.4300
> [ 5.504139] drxk: frontend initialized.
> [ 5.517782] mt2063_attach: Attaching MT2063
> [ 5.517788] DVB: registering new adapter (cx23885[0])
> [ 5.517791] DVB: registering adapter 1 frontend 0 (DRXK DVB-T)...
> [ 5.518664] cx23885_dvb_register() allocating 1 frontend(s)
> [ 5.518668] cx23885[0]: cx23885 based dvb card
> [ 5.533886] drxk: status = 0x639130d9
> [ 5.533896] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz
> [ 5.617338] DRXK driver version 0.9.4300
> [ 5.650861] drxk: frontend initialized.
> [ 5.650872] mt2063_attach: Attaching MT2063
> [ 5.650876] DVB: registering new adapter (cx23885[0])
> [ 5.650878] DVB: registering adapter 2 frontend 0 (DRXK DVB-C DVB-T)...
> [ 5.651338] cx23885_dev_checkrevision() Hardware revision = 0xa5
> [ 5.651343] cx23885[0]/0: found at 0000:02:00.0, rev: 4, irq: 16,
> latency: 0, mmio: 0xff400000
> ........
> [ 153.727978] mt2063: detected a mt2063 B3
> [ 153.877050] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 153.877058] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
> [ 156.989702] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 156.989710] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
> [ 170.558420] mt2063: detected a mt2063 B3
> [ 170.629422] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 170.629430] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
> [ 173.742057] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 173.742065] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
> [ 251.314900] mt2063: detected a mt2063 B3
> [ 251.385932] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 251.385940] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
> [ 254.498522] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
> [ 254.498530] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
>
> lspci -vvv
> 02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885
> PCI Video and Audio Decoder (rev 04)
> Subsystem: TERRATEC Electronic GmbH Cinergy T PCIe Dual
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at ff400000 (64-bit, non-prefetchable) [size=2M]
> Capabilities: [40] Express (v1) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1 <1us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0 <2us, L1 <4us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive- BWMgmt- ABWMgmt-
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [90] Vital Product Data
> Product Name: "
> End
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
> Capabilities: [200 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed+ WRR32+ WRR64+ WRR128-
> Ctrl: ArbSelect=WRR64
> Status: InProgress-
> Port Arbitration Table [240] <?>
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
> Status: NegoPending- InProgress-
> Kernel driver in use: cx23885
> Kernel modules: cx23885
>
> It says no signal, but if I put the antenna-cable in my other DVB-C
> card and do a scan I get:
> Philips TV-Card
> dvbv5-scan -a0 -v channel2.conf
> using demux '/dev/dvb/adapter0/demux0'
> Device Philips TDA10023 DVB-C (/dev/dvb/adapter0/frontend0) capabilities:
> CAN_FEC_AUTO CAN_INVERSION_AUTO CAN_QAM_16 CAN_QAM_32
> CAN_QAM_64 CAN_QAM_128 CAN_QAM_256 CAN_QPSK
> DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
> Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C
> Scanning frequency #1 304000000
> FREQUENCY = 304000000
> MODULATION = QAM/64
> INVERSION = AUTO
> SYMBOL_RATE = 6875000
> INNER_FEC = AUTO
> DELIVERY_SYSTEM = DVBC/ANNEX_A
> status 1f | signal 97% | snr 94% | ber 1728 | unc 62194 | FE_HAS_LOCK
>
> Service #0 (101) Nederland 1 channel 0.1.0
> Service #1 (102) Nederland 2 channel 0.2.1
> Service #2 (103) Nederland 3 channel 0.3.2
> Service #3 (8101) 100%NL channel 0.801.3
> Service #4 (8102) Arrow Classic Rock channel 0.802.4
> Service #5 (8103) Arrow Jazz channel 0.803.5
> Service #6 (8104) BBC radio 1 channel 0.804.6
> Service #7 (8105) BBC radio 2 channel 0.805.7
> Service #8 (8106) BBC radio 3 channel 0.806.8
> Service #9 (8107) BBC radio 4 channel 0.807.9
> Service #10 (8108) BNR channel 0.808.10
> Service #11 (8109) Classic FM channel 0.809.11
> New transponder/channel found: #2: 505937920
> New transponder/channel found: #3: 515112960
> New transponder/channel found: #4: 524288000
> New transponder/channel found: #5: 529530880
> New transponder/channel found: #6: 538705920
> New transponder/channel found: #7: 547880960
> New transponder/channel found: #8: 557056000
> New transponder/channel found: #9: 566231040
> New transponder/channel found: #10: 312000000
> New transponder/channel found: #11: 320000000
> New transponder/channel found: #12: 328000000
> New transponder/channel found: #13: 336000000
> New transponder/channel found: #14: 580648960
> New transponder/channel found: #15: 344000000
> New transponder/channel found: #16: 352000000
> New transponder/channel found: #17: 360000000
> New transponder/channel found: #18: 368000000
>
> Does anyone know what I'm doing wrong?
> Thanks,
>
> Jan Saris
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: No Signal with TerraTec Cinergy T PCIe dual
2013-04-07 15:42 ` Oliver Schinagl
@ 2013-04-09 8:47 ` Jan Saris
2013-04-08 17:58 ` Oliver Schinagl
2013-04-09 9:31 ` Cédric Girard
0 siblings, 2 replies; 9+ messages in thread
From: Jan Saris @ 2013-04-09 8:47 UTC (permalink / raw)
To: Oliver Schinagl; +Cc: linux-media
Hi,
Thanks for your reply,
Do you only use DVB-T, or also DVB-C? Because it looks to me that
DVB-C isn't implemented, or at least giving me a lot of errors?
I use the correct front-end of adapter2 (as you can see in the log:
DELIVERY_SYSTEM = DVBC/ANNEX_A)
adapter1 is only DVB-T
What do you meen by: "Remember to set the frontend properly;
dvb-fe-tool from memory"??
To set the delevery system to DVB-C before running the dvbv5-scan??
Jan
2013/4/7 Oliver Schinagl <oliver+list@schinagl.nl>:
> On 07-04-13 12:56, Jan Saris wrote:
>>
>> Hi,
>>
>> Sinse a couple of months I'm trying to get my second DVB-C card to
>> work, but with no luck.
>> I have searched a lot around and even tried the last media_build.
>
> I have the same card and while I don't see anything wrong (you have 2 dvb-t
> devices installed right? adapter0 is something else, and the Cinergy is
> adapter1 and adapter2? Ah, yes you do say 'other dvb-c' sorry.
>
>> I am running linux 3.5.0-26-generic with the latests media_build from
>> here (http://git.linuxtv.org/media_build.git)
>>
>> For some reason the card won't get a lock. Here are my test results:
>
> Remember to set the frontend properly; dvb-fe-tool from memory (tab
> completion ftw). And remember the cinergy is dual dvb-t; but only single
> dvb-c (and single analog, but i think that is still not implemented?)
>>
>>
>> Terratec Cinergy PCIe Dual
>> dvbv5-scan -a2 -v channel2.conf
>> using demux '/dev/dvb/adapter2/demux0'
>> Device DRXK DVB-C DVB-T (/dev/dvb/adapter2/frontend0) capabilities:
>> CAN_FEC_1_2 CAN_FEC_2_3 CAN_FEC_3_4 CAN_FEC_5_6 CAN_FEC_7_8
>> CAN_FEC_AUTO CAN_GUARD_INTERVAL_AUTO CAN_HIERARCHY_AUTO
>> CAN_INVERSION_AUTO CAN_MUTE_TS CAN_QAM_16 CAN_QAM_32 CAN_QAM_64
>> CAN_QAM_128 CAN_QAM_256 CAN_RECOVER CAN_TRANSMISSION_MODE_AUTO
>> DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
>> Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C DVBT
>> Scanning frequency #1 304000000
>> FREQUENCY = 304000000
>> MODULATION = QAM/64
>> INVERSION = AUTO
>> SYMBOL_RATE = 6875000
>> INNER_FEC = AUTO
>> DELIVERY_SYSTEM = DVBC/ANNEX_A
>> status 00 | signal 0% | snr 0% | ber 0 | unc 119 | tune failed
>> dmesg
>> [ 5.332360] cx23885_dvb_register() allocating 1 frontend(s)
>> [ 5.332365] cx23885[0]: cx23885 based dvb card
>> [ 5.365162] drxk: status = 0x639160d9
>> [ 5.365167] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz
>> [ 5.465869] DRXK driver version 0.9.4300
>> [ 5.504139] drxk: frontend initialized.
>> [ 5.517782] mt2063_attach: Attaching MT2063
>> [ 5.517788] DVB: registering new adapter (cx23885[0])
>> [ 5.517791] DVB: registering adapter 1 frontend 0 (DRXK DVB-T)...
>> [ 5.518664] cx23885_dvb_register() allocating 1 frontend(s)
>> [ 5.518668] cx23885[0]: cx23885 based dvb card
>> [ 5.533886] drxk: status = 0x639130d9
>> [ 5.533896] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz
>> [ 5.617338] DRXK driver version 0.9.4300
>> [ 5.650861] drxk: frontend initialized.
>> [ 5.650872] mt2063_attach: Attaching MT2063
>> [ 5.650876] DVB: registering new adapter (cx23885[0])
>> [ 5.650878] DVB: registering adapter 2 frontend 0 (DRXK DVB-C DVB-T)...
>> [ 5.651338] cx23885_dev_checkrevision() Hardware revision = 0xa5
>> [ 5.651343] cx23885[0]/0: found at 0000:02:00.0, rev: 4, irq: 16,
>> latency: 0, mmio: 0xff400000
>> ........
>> [ 153.727978] mt2063: detected a mt2063 B3
>> [ 153.877050] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>> params:
>> [ 153.877058] drxk: 02 00 00 00 10 00 05 00 03 02
>> ..........
>> [ 156.989702] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>> params:
>> [ 156.989710] drxk: 02 00 00 00 10 00 05 00 03 02
>> ..........
>> [ 170.558420] mt2063: detected a mt2063 B3
>> [ 170.629422] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>> params:
>> [ 170.629430] drxk: 02 00 00 00 10 00 05 00 03 02
>> ..........
>> [ 173.742057] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>> params:
>> [ 173.742065] drxk: 02 00 00 00 10 00 05 00 03 02
>> ..........
>> [ 251.314900] mt2063: detected a mt2063 B3
>> [ 251.385932] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>> params:
>> [ 251.385940] drxk: 02 00 00 00 10 00 05 00 03 02
>> ..........
>> [ 254.498522] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>> params:
>> [ 254.498530] drxk: 02 00 00 00 10 00 05 00 03 02
>> ..........
>>
>> lspci -vvv
>> 02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885
>> PCI Video and Audio Decoder (rev 04)
>> Subsystem: TERRATEC Electronic GmbH Cinergy T PCIe Dual
>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B- DisINTx-
>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>> Latency: 0, Cache Line Size: 64 bytes
>> Interrupt: pin A routed to IRQ 16
>> Region 0: Memory at ff400000 (64-bit, non-prefetchable) [size=2M]
>> Capabilities: [40] Express (v1) Endpoint, MSI 00
>> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
>> <64ns, L1 <1us
>> ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
>> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
>> Unsupported-
>> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
>> MaxPayload 128 bytes, MaxReadReq 512 bytes
>> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
>> AuxPwr- TransPend-
>> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
>> Latency L0 <2us, L1 <4us
>> ClockPM- Surprise- LLActRep- BwNot-
>> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
>> CommClk+
>> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
>> SlotClk+ DLActive- BWMgmt- ABWMgmt-
>> Capabilities: [80] Power Management version 2
>> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
>> PME(D0+,D1+,D2+,D3hot+,D3cold-)
>> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>> Capabilities: [90] Vital Product Data
>> Product Name: "
>> End
>> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
>> Address: 0000000000000000 Data: 0000
>> Capabilities: [100 v1] Advanced Error Reporting
>> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
>> UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
>> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
>> UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
>> UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
>> UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
>> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
>> NonFatalErr-
>> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
>> NonFatalErr-
>> AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap-
>> ChkEn-
>> Capabilities: [200 v1] Virtual Channel
>> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
>> Arb: Fixed+ WRR32+ WRR64+ WRR128-
>> Ctrl: ArbSelect=WRR64
>> Status: InProgress-
>> Port Arbitration Table [240] <?>
>> VC0: Caps: PATOffset=00 MaxTimeSlots=1
>> RejSnoopTrans-
>> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
>> WRR256-
>> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
>> Status: NegoPending- InProgress-
>> Kernel driver in use: cx23885
>> Kernel modules: cx23885
>>
>> It says no signal, but if I put the antenna-cable in my other DVB-C
>> card and do a scan I get:
>> Philips TV-Card
>> dvbv5-scan -a0 -v channel2.conf
>> using demux '/dev/dvb/adapter0/demux0'
>> Device Philips TDA10023 DVB-C (/dev/dvb/adapter0/frontend0) capabilities:
>> CAN_FEC_AUTO CAN_INVERSION_AUTO CAN_QAM_16 CAN_QAM_32
>> CAN_QAM_64 CAN_QAM_128 CAN_QAM_256 CAN_QPSK
>> DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
>> Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C
>> Scanning frequency #1 304000000
>> FREQUENCY = 304000000
>> MODULATION = QAM/64
>> INVERSION = AUTO
>> SYMBOL_RATE = 6875000
>> INNER_FEC = AUTO
>> DELIVERY_SYSTEM = DVBC/ANNEX_A
>> status 1f | signal 97% | snr 94% | ber 1728 | unc 62194 | FE_HAS_LOCK
>>
>> Service #0 (101) Nederland 1 channel 0.1.0
>> Service #1 (102) Nederland 2 channel 0.2.1
>> Service #2 (103) Nederland 3 channel 0.3.2
>> Service #3 (8101) 100%NL channel 0.801.3
>> Service #4 (8102) Arrow Classic Rock channel 0.802.4
>> Service #5 (8103) Arrow Jazz channel 0.803.5
>> Service #6 (8104) BBC radio 1 channel 0.804.6
>> Service #7 (8105) BBC radio 2 channel 0.805.7
>> Service #8 (8106) BBC radio 3 channel 0.806.8
>> Service #9 (8107) BBC radio 4 channel 0.807.9
>> Service #10 (8108) BNR channel 0.808.10
>> Service #11 (8109) Classic FM channel 0.809.11
>> New transponder/channel found: #2: 505937920
>> New transponder/channel found: #3: 515112960
>> New transponder/channel found: #4: 524288000
>> New transponder/channel found: #5: 529530880
>> New transponder/channel found: #6: 538705920
>> New transponder/channel found: #7: 547880960
>> New transponder/channel found: #8: 557056000
>> New transponder/channel found: #9: 566231040
>> New transponder/channel found: #10: 312000000
>> New transponder/channel found: #11: 320000000
>> New transponder/channel found: #12: 328000000
>> New transponder/channel found: #13: 336000000
>> New transponder/channel found: #14: 580648960
>> New transponder/channel found: #15: 344000000
>> New transponder/channel found: #16: 352000000
>> New transponder/channel found: #17: 360000000
>> New transponder/channel found: #18: 368000000
>>
>> Does anyone know what I'm doing wrong?
>> Thanks,
>>
>> Jan Saris
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-media" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: No Signal with TerraTec Cinergy T PCIe dual
2013-04-09 8:47 ` Jan Saris
@ 2013-04-08 17:58 ` Oliver Schinagl
2013-04-09 9:31 ` Cédric Girard
1 sibling, 0 replies; 9+ messages in thread
From: Oliver Schinagl @ 2013-04-08 17:58 UTC (permalink / raw)
To: Jan Saris; +Cc: linux-media
On 09-04-13 10:47, Jan Saris wrote:
> Hi,
>
> Thanks for your reply,
> Do you only use DVB-T, or also DVB-C? Because it looks to me that
> DVB-C isn't implemented, or at least giving me a lot of errors?
>
> I use the correct front-end of adapter2 (as you can see in the log:
> DELIVERY_SYSTEM = DVBC/ANNEX_A)
> adapter1 is only DVB-T
I watch via DVB-T so I always have to set that to my second tuner (to
have dual tuner possibility).
dvb-fe-tool -a 0 -d DVB-T
dvb-fe-tool -a 1 -d DVB-T
for adapter 0 and 1.
In your case however, you do not use DVB-T. The first tuner thus is
useless (It can only function as Analog tuner, but I have no idea what
the status for that is atm), I can't 'choose' it as delivery system.
As for adapter 1, You can swap between DVBT, DVBC/ANNEX_A and
DVBC/ANNEX_C. So that's DVBT and DVBC, but two flavors. I don't know
what it means, but you can try switching between those two?
dvb-fe-tool -a 1 -d DVBC/ANNEX_C
Give it a shot :)
>
> What do you meen by: "Remember to set the frontend properly;
> dvb-fe-tool from memory"??
> To set the delevery system to DVB-C before running the dvbv5-scan??
>
> Jan
>
> 2013/4/7 Oliver Schinagl <oliver+list@schinagl.nl>:
>> On 07-04-13 12:56, Jan Saris wrote:
>>> Hi,
>>>
>>> Sinse a couple of months I'm trying to get my second DVB-C card to
>>> work, but with no luck.
>>> I have searched a lot around and even tried the last media_build.
>> I have the same card and while I don't see anything wrong (you have 2 dvb-t
>> devices installed right? adapter0 is something else, and the Cinergy is
>> adapter1 and adapter2? Ah, yes you do say 'other dvb-c' sorry.
>>
>>> I am running linux 3.5.0-26-generic with the latests media_build from
>>> here (http://git.linuxtv.org/media_build.git)
>>>
>>> For some reason the card won't get a lock. Here are my test results:
>> Remember to set the frontend properly; dvb-fe-tool from memory (tab
>> completion ftw). And remember the cinergy is dual dvb-t; but only single
>> dvb-c (and single analog, but i think that is still not implemented?)
>>>
>>> Terratec Cinergy PCIe Dual
>>> dvbv5-scan -a2 -v channel2.conf
>>> using demux '/dev/dvb/adapter2/demux0'
>>> Device DRXK DVB-C DVB-T (/dev/dvb/adapter2/frontend0) capabilities:
>>> CAN_FEC_1_2 CAN_FEC_2_3 CAN_FEC_3_4 CAN_FEC_5_6 CAN_FEC_7_8
>>> CAN_FEC_AUTO CAN_GUARD_INTERVAL_AUTO CAN_HIERARCHY_AUTO
>>> CAN_INVERSION_AUTO CAN_MUTE_TS CAN_QAM_16 CAN_QAM_32 CAN_QAM_64
>>> CAN_QAM_128 CAN_QAM_256 CAN_RECOVER CAN_TRANSMISSION_MODE_AUTO
>>> DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
>>> Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C DVBT
>>> Scanning frequency #1 304000000
>>> FREQUENCY = 304000000
>>> MODULATION = QAM/64
>>> INVERSION = AUTO
>>> SYMBOL_RATE = 6875000
>>> INNER_FEC = AUTO
>>> DELIVERY_SYSTEM = DVBC/ANNEX_A
>>> status 00 | signal 0% | snr 0% | ber 0 | unc 119 | tune failed
>>> dmesg
>>> [ 5.332360] cx23885_dvb_register() allocating 1 frontend(s)
>>> [ 5.332365] cx23885[0]: cx23885 based dvb card
>>> [ 5.365162] drxk: status = 0x639160d9
>>> [ 5.365167] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz
>>> [ 5.465869] DRXK driver version 0.9.4300
>>> [ 5.504139] drxk: frontend initialized.
>>> [ 5.517782] mt2063_attach: Attaching MT2063
>>> [ 5.517788] DVB: registering new adapter (cx23885[0])
>>> [ 5.517791] DVB: registering adapter 1 frontend 0 (DRXK DVB-T)...
>>> [ 5.518664] cx23885_dvb_register() allocating 1 frontend(s)
>>> [ 5.518668] cx23885[0]: cx23885 based dvb card
>>> [ 5.533886] drxk: status = 0x639130d9
>>> [ 5.533896] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz
>>> [ 5.617338] DRXK driver version 0.9.4300
>>> [ 5.650861] drxk: frontend initialized.
>>> [ 5.650872] mt2063_attach: Attaching MT2063
>>> [ 5.650876] DVB: registering new adapter (cx23885[0])
>>> [ 5.650878] DVB: registering adapter 2 frontend 0 (DRXK DVB-C DVB-T)...
>>> [ 5.651338] cx23885_dev_checkrevision() Hardware revision = 0xa5
>>> [ 5.651343] cx23885[0]/0: found at 0000:02:00.0, rev: 4, irq: 16,
>>> latency: 0, mmio: 0xff400000
>>> ........
>>> [ 153.727978] mt2063: detected a mt2063 B3
>>> [ 153.877050] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>>> params:
>>> [ 153.877058] drxk: 02 00 00 00 10 00 05 00 03 02
>>> ..........
>>> [ 156.989702] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>>> params:
>>> [ 156.989710] drxk: 02 00 00 00 10 00 05 00 03 02
>>> ..........
>>> [ 170.558420] mt2063: detected a mt2063 B3
>>> [ 170.629422] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>>> params:
>>> [ 170.629430] drxk: 02 00 00 00 10 00 05 00 03 02
>>> ..........
>>> [ 173.742057] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>>> params:
>>> [ 173.742065] drxk: 02 00 00 00 10 00 05 00 03 02
>>> ..........
>>> [ 251.314900] mt2063: detected a mt2063 B3
>>> [ 251.385932] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>>> params:
>>> [ 251.385940] drxk: 02 00 00 00 10 00 05 00 03 02
>>> ..........
>>> [ 254.498522] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with
>>> params:
>>> [ 254.498530] drxk: 02 00 00 00 10 00 05 00 03 02
>>> ..........
>>>
>>> lspci -vvv
>>> 02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885
>>> PCI Video and Audio Decoder (rev 04)
>>> Subsystem: TERRATEC Electronic GmbH Cinergy T PCIe Dual
>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>>> ParErr- Stepping- SERR- FastB2B- DisINTx-
>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>> Latency: 0, Cache Line Size: 64 bytes
>>> Interrupt: pin A routed to IRQ 16
>>> Region 0: Memory at ff400000 (64-bit, non-prefetchable) [size=2M]
>>> Capabilities: [40] Express (v1) Endpoint, MSI 00
>>> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
>>> <64ns, L1 <1us
>>> ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
>>> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
>>> Unsupported-
>>> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
>>> MaxPayload 128 bytes, MaxReadReq 512 bytes
>>> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
>>> AuxPwr- TransPend-
>>> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
>>> Latency L0 <2us, L1 <4us
>>> ClockPM- Surprise- LLActRep- BwNot-
>>> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
>>> CommClk+
>>> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>>> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
>>> SlotClk+ DLActive- BWMgmt- ABWMgmt-
>>> Capabilities: [80] Power Management version 2
>>> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
>>> PME(D0+,D1+,D2+,D3hot+,D3cold-)
>>> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>>> Capabilities: [90] Vital Product Data
>>> Product Name: "
>>> End
>>> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
>>> Address: 0000000000000000 Data: 0000
>>> Capabilities: [100 v1] Advanced Error Reporting
>>> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
>>> UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
>>> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
>>> UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
>>> UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
>>> UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
>>> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
>>> NonFatalErr-
>>> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
>>> NonFatalErr-
>>> AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap-
>>> ChkEn-
>>> Capabilities: [200 v1] Virtual Channel
>>> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
>>> Arb: Fixed+ WRR32+ WRR64+ WRR128-
>>> Ctrl: ArbSelect=WRR64
>>> Status: InProgress-
>>> Port Arbitration Table [240] <?>
>>> VC0: Caps: PATOffset=00 MaxTimeSlots=1
>>> RejSnoopTrans-
>>> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
>>> WRR256-
>>> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
>>> Status: NegoPending- InProgress-
>>> Kernel driver in use: cx23885
>>> Kernel modules: cx23885
>>>
>>> It says no signal, but if I put the antenna-cable in my other DVB-C
>>> card and do a scan I get:
>>> Philips TV-Card
>>> dvbv5-scan -a0 -v channel2.conf
>>> using demux '/dev/dvb/adapter0/demux0'
>>> Device Philips TDA10023 DVB-C (/dev/dvb/adapter0/frontend0) capabilities:
>>> CAN_FEC_AUTO CAN_INVERSION_AUTO CAN_QAM_16 CAN_QAM_32
>>> CAN_QAM_64 CAN_QAM_128 CAN_QAM_256 CAN_QPSK
>>> DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
>>> Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C
>>> Scanning frequency #1 304000000
>>> FREQUENCY = 304000000
>>> MODULATION = QAM/64
>>> INVERSION = AUTO
>>> SYMBOL_RATE = 6875000
>>> INNER_FEC = AUTO
>>> DELIVERY_SYSTEM = DVBC/ANNEX_A
>>> status 1f | signal 97% | snr 94% | ber 1728 | unc 62194 | FE_HAS_LOCK
>>>
>>> Service #0 (101) Nederland 1 channel 0.1.0
>>> Service #1 (102) Nederland 2 channel 0.2.1
>>> Service #2 (103) Nederland 3 channel 0.3.2
>>> Service #3 (8101) 100%NL channel 0.801.3
>>> Service #4 (8102) Arrow Classic Rock channel 0.802.4
>>> Service #5 (8103) Arrow Jazz channel 0.803.5
>>> Service #6 (8104) BBC radio 1 channel 0.804.6
>>> Service #7 (8105) BBC radio 2 channel 0.805.7
>>> Service #8 (8106) BBC radio 3 channel 0.806.8
>>> Service #9 (8107) BBC radio 4 channel 0.807.9
>>> Service #10 (8108) BNR channel 0.808.10
>>> Service #11 (8109) Classic FM channel 0.809.11
>>> New transponder/channel found: #2: 505937920
>>> New transponder/channel found: #3: 515112960
>>> New transponder/channel found: #4: 524288000
>>> New transponder/channel found: #5: 529530880
>>> New transponder/channel found: #6: 538705920
>>> New transponder/channel found: #7: 547880960
>>> New transponder/channel found: #8: 557056000
>>> New transponder/channel found: #9: 566231040
>>> New transponder/channel found: #10: 312000000
>>> New transponder/channel found: #11: 320000000
>>> New transponder/channel found: #12: 328000000
>>> New transponder/channel found: #13: 336000000
>>> New transponder/channel found: #14: 580648960
>>> New transponder/channel found: #15: 344000000
>>> New transponder/channel found: #16: 352000000
>>> New transponder/channel found: #17: 360000000
>>> New transponder/channel found: #18: 368000000
>>>
>>> Does anyone know what I'm doing wrong?
>>> Thanks,
>>>
>>> Jan Saris
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-media" in
>>> the body of a message to majordomo@vger.kernel.org
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: No Signal with TerraTec Cinergy T PCIe dual
2013-04-09 8:47 ` Jan Saris
2013-04-08 17:58 ` Oliver Schinagl
@ 2013-04-09 9:31 ` Cédric Girard
1 sibling, 0 replies; 9+ messages in thread
From: Cédric Girard @ 2013-04-09 9:31 UTC (permalink / raw)
To: linux-media
On Tue, Apr 9, 2013 at 10:47 AM, Jan Saris wrote:
>
> What do you meen by: "Remember to set the frontend properly;
> dvb-fe-tool from memory"??
> To set the delevery system to DVB-C before running the dvbv5-scan??
Yes but from what I remember, DVB-C is the default.
Anyway the flag from dvb-fe-tool to use is --set-delsys=DVB-C in your case.
--
Cédric Girard
^ permalink raw reply [flat|nested] 9+ messages in thread
* No Signal with TerraTec Cinergy T PCIe dual
@ 2013-01-08 21:02 Cédric Girard
2013-01-08 21:46 ` Antti Palosaari
0 siblings, 1 reply; 9+ messages in thread
From: Cédric Girard @ 2013-01-08 21:02 UTC (permalink / raw)
To: linux-media
Hi,
Since a few weeks, I am unable to use my TerraTec Cinergy T PCIe dual
card anymore. On the kernel and drivers side, everything seems to be
working as expected but I get no signal from any channel.
It used to work and I have done too many updates recently to be able
to pinpoint to from which point it stopped to work.
Plugging the same cable to my TV tuner I get perfect reception so no
change in signal quality.
I am running Arch Linux with linux 3.7.1 on an x86_64 architecture.
Following are some logs.
Kernel logs when loading cx23885 module:
###
[93752.708088] cx23885 driver version 0.0.3 loaded
[93752.708954] CORE cx23885[0]: subsystem: 153b:117e, board: TerraTec
Cinergy T PCIe Dual [card=34,autodetected]
[93752.847421] cx25840 12-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0])
[93753.502291] cx25840 12-0044: loaded v4l-cx23885-avcore-01.fw
firmware (16382 bytes)
[93753.518236] cx23885_dvb_register() allocating 1 frontend(s)
[93753.518242] cx23885[0]: cx23885 based dvb card
[93753.533378] drxk: status = 0x639160d9
[93753.533383] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz
[93753.606391] DRXK driver version 0.9.4300
[93753.630635] drxk: frontend initialized.
[93753.667152] mt2063_attach: Attaching MT2063
[93753.667156] DVB: registering new adapter (cx23885[0])
[93753.667161] cx23885 0000:03:00.0: DVB: registering adapter 0
frontend 0 (DRXK DVB-T)...
[93753.670728] cx23885_dvb_register() allocating 1 frontend(s)
[93753.670732] cx23885[0]: cx23885 based dvb card
[93753.686602] drxk: status = 0x639130d9
[93753.686605] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz
[93753.759577] DRXK driver version 0.9.4300
[93753.783845] drxk: frontend initialized.
[93753.783852] mt2063_attach: Attaching MT2063
[93753.783854] DVB: registering new adapter (cx23885[0])
[93753.783858] cx23885 0000:03:00.0: DVB: registering adapter 1
frontend 0 (DRXK DVB-C DVB-T)...
[93753.784284] cx23885_dev_checkrevision() Hardware revision = 0xa5
[93753.784290] cx23885[0]/0: found at 0000:03:00.0, rev: 4, irq: 18,
latency: 0, mmio: 0xfb800000
###
Kernel logs when scanning
###
[93853.705675] mt2063: detected a mt2063 B3
###
"femon -H -a0" output:
###
FE: DRXK DVB-T (DVBT)
Problem retrieving frontend information: Resource temporarily unavailable
status SCV | signal 49% | snr 0% | ber 2014507767 | unc 1 |
###
Meaningful bits of an strace of the same command
###
ioctl(3, FE_READ_STATUS, 0x7fff69172ef0) = 0
ioctl(3, FE_READ_BER, 0x7fff69173018) = -1 EAGAIN (Resource
temporarily unavailable)
ioctl(3, FE_READ_SIGNAL_STRENGTH, 0x7fff6917301c) = -1 EAGAIN
(Resource temporarily unavailable)
ioctl(3, FE_READ_SNR, 0x7fff6917301e) = -1 EAGAIN (Resource
temporarily unavailable)
ioctl(3, FE_READ_UNCORRECTED_BLOCKS, 0x7fff69173020) = -1 EAGAIN
(Resource temporarily unavailable)
###
w_scan give "no signal" result.
dvbscan give "Unable to query frontend status"
Any hint to where I should look would be welcome!
Regards,
--
Cédric Girard
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: No Signal with TerraTec Cinergy T PCIe dual
2013-01-08 21:02 Cédric Girard
@ 2013-01-08 21:46 ` Antti Palosaari
2013-01-08 22:10 ` Cédric Girard
0 siblings, 1 reply; 9+ messages in thread
From: Antti Palosaari @ 2013-01-08 21:46 UTC (permalink / raw)
To: Cédric Girard; +Cc: linux-media
On 01/08/2013 11:02 PM, Cédric Girard wrote:
> Hi,
>
> Since a few weeks, I am unable to use my TerraTec Cinergy T PCIe dual
> card anymore. On the kernel and drivers side, everything seems to be
> working as expected but I get no signal from any channel.
>
> It used to work and I have done too many updates recently to be able
> to pinpoint to from which point it stopped to work.
> Plugging the same cable to my TV tuner I get perfect reception so no
> change in signal quality.
>
> I am running Arch Linux with linux 3.7.1 on an x86_64 architecture.
>
> Following are some logs.
>
> Kernel logs when loading cx23885 module:
> ###
> [93752.708088] cx23885 driver version 0.0.3 loaded
> [93752.708954] CORE cx23885[0]: subsystem: 153b:117e, board: TerraTec
> Cinergy T PCIe Dual [card=34,autodetected]
> [93752.847421] cx25840 12-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0])
> [93753.502291] cx25840 12-0044: loaded v4l-cx23885-avcore-01.fw
> firmware (16382 bytes)
> [93753.518236] cx23885_dvb_register() allocating 1 frontend(s)
> [93753.518242] cx23885[0]: cx23885 based dvb card
> [93753.533378] drxk: status = 0x639160d9
> [93753.533383] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz
> [93753.606391] DRXK driver version 0.9.4300
> [93753.630635] drxk: frontend initialized.
> [93753.667152] mt2063_attach: Attaching MT2063
> [93753.667156] DVB: registering new adapter (cx23885[0])
> [93753.667161] cx23885 0000:03:00.0: DVB: registering adapter 0
> frontend 0 (DRXK DVB-T)...
> [93753.670728] cx23885_dvb_register() allocating 1 frontend(s)
> [93753.670732] cx23885[0]: cx23885 based dvb card
> [93753.686602] drxk: status = 0x639130d9
> [93753.686605] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz
> [93753.759577] DRXK driver version 0.9.4300
> [93753.783845] drxk: frontend initialized.
> [93753.783852] mt2063_attach: Attaching MT2063
> [93753.783854] DVB: registering new adapter (cx23885[0])
> [93753.783858] cx23885 0000:03:00.0: DVB: registering adapter 1
> frontend 0 (DRXK DVB-C DVB-T)...
> [93753.784284] cx23885_dev_checkrevision() Hardware revision = 0xa5
> [93753.784290] cx23885[0]/0: found at 0000:03:00.0, rev: 4, irq: 18,
> latency: 0, mmio: 0xfb800000
> ###
>
> Kernel logs when scanning
> ###
> [93853.705675] mt2063: detected a mt2063 B3
> ###
>
> "femon -H -a0" output:
> ###
> FE: DRXK DVB-T (DVBT)
> Problem retrieving frontend information: Resource temporarily unavailable
> status SCV | signal 49% | snr 0% | ber 2014507767 | unc 1 |
> ###
>
> Meaningful bits of an strace of the same command
> ###
> ioctl(3, FE_READ_STATUS, 0x7fff69172ef0) = 0
> ioctl(3, FE_READ_BER, 0x7fff69173018) = -1 EAGAIN (Resource
> temporarily unavailable)
> ioctl(3, FE_READ_SIGNAL_STRENGTH, 0x7fff6917301c) = -1 EAGAIN
> (Resource temporarily unavailable)
> ioctl(3, FE_READ_SNR, 0x7fff6917301e) = -1 EAGAIN (Resource
> temporarily unavailable)
> ioctl(3, FE_READ_UNCORRECTED_BLOCKS, 0x7fff69173020) = -1 EAGAIN
> (Resource temporarily unavailable)
> ###
I could guess these errors are coming because you query statistics but
device is sleeping and statistics cannot be offered. -EAGAIN == device
is sleeping, -ENOTTY device does not support given statistic at all.
Could you ensure that? Use some app, like w_scan, tzap, czap, etc. to
tune and recheck if it shows these or not. femon could not tune, it
queries only statistics. You will need to leave tuning on and then use
other terminal for femon.
> w_scan give "no signal" result.
> dvbscan give "Unable to query frontend status"
hmm, that dvbscan results sounds crazy. I am not sure about these
scanning apps as there is scan, dvbscan, scandvb. Maybe some of those,
or even all, are just same app but renamed as "scan" is too general. My
Fedora 17 has scandvb. I just tested against one DRX-K device and it
worked fine.
> Any hint to where I should look would be welcome!
Try to downgrade Kernels until you find working one.
regards
Antti
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: No Signal with TerraTec Cinergy T PCIe dual
2013-01-08 21:46 ` Antti Palosaari
@ 2013-01-08 22:10 ` Cédric Girard
2013-03-06 14:28 ` Cédric Girard
0 siblings, 1 reply; 9+ messages in thread
From: Cédric Girard @ 2013-01-08 22:10 UTC (permalink / raw)
To: linux-media
On Tue, Jan 8, 2013 at 10:46 PM, Antti Palosaari wrote:
> On 01/08/2013 11:02 PM, Cédric Girard wrote:
>> Meaningful bits of an strace of the same command
>> ###
>> ioctl(3, FE_READ_STATUS, 0x7fff69172ef0) = 0
>> ioctl(3, FE_READ_BER, 0x7fff69173018) = -1 EAGAIN (Resource
>> temporarily unavailable)
>> ioctl(3, FE_READ_SIGNAL_STRENGTH, 0x7fff6917301c) = -1 EAGAIN
>> (Resource temporarily unavailable)
>> ioctl(3, FE_READ_SNR, 0x7fff6917301e) = -1 EAGAIN (Resource
>> temporarily unavailable)
>> ioctl(3, FE_READ_UNCORRECTED_BLOCKS, 0x7fff69173020) = -1 EAGAIN
>> (Resource temporarily unavailable)
>> ###
>
>
> I could guess these errors are coming because you query statistics but
> device is sleeping and statistics cannot be offered. -EAGAIN == device is
> sleeping, -ENOTTY device does not support given statistic at all.
>
> Could you ensure that? Use some app, like w_scan, tzap, czap, etc. to tune
> and recheck if it shows these or not. femon could not tune, it queries only
> statistics. You will need to leave tuning on and then use other terminal for
> femon.
You were right. Now I get this while running w_scan in another terminal:
###
status SCV | signal 5% | snr 0% | ber 0 | unc 0 |
status SCV | signal 5% | snr 0% | ber 0 | unc 0 |
status SCV | signal 5% | snr 0% | ber 0 | unc 0 |
[...]
###
This is coherent with the "no signal" result.
>
>
>> w_scan give "no signal" result.
>> dvbscan give "Unable to query frontend status"
>
>
> hmm, that dvbscan results sounds crazy. I am not sure about these scanning
> apps as there is scan, dvbscan, scandvb. Maybe some of those, or even all,
> are just same app but renamed as "scan" is too general. My Fedora 17 has
> scandvb. I just tested against one DRX-K device and it worked fine.
According to the wiki [1] scandvb is a distro-side renaming of dvbscan.
>
>
>> Any hint to where I should look would be welcome!
>
>
> Try to downgrade Kernels until you find working one.
Guess it is probably the only way. I will try.
[1] http://linuxtv.org/wiki/index.php/Dvbscan
--
Cédric Girard
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: No Signal with TerraTec Cinergy T PCIe dual
2013-01-08 22:10 ` Cédric Girard
@ 2013-03-06 14:28 ` Cédric Girard
0 siblings, 0 replies; 9+ messages in thread
From: Cédric Girard @ 2013-03-06 14:28 UTC (permalink / raw)
To: linux-media
On Tue, Jan 8, 2013 at 10:46 PM, Antti Palosaari wrote:
>
> Try to downgrade Kernels until you find working one.
>
> Guess it is probably the only way. I will try.
Seeing other message about a problem with the same card, made me think
I forgot to post my conclusion.
I downgraded to 3.6.5 which was a working one at the time I got the
card and the problem is the same. The problem is thus elsewhere (maybe
hardware related but it is difficult to me to test the card in another
computer).
--
Cédric Girard
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2013-04-09 10:26 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-04-07 10:56 No Signal with TerraTec Cinergy T PCIe dual Jan Saris
2013-04-07 15:42 ` Oliver Schinagl
2013-04-09 8:47 ` Jan Saris
2013-04-08 17:58 ` Oliver Schinagl
2013-04-09 9:31 ` Cédric Girard
-- strict thread matches above, loose matches on Subject: below --
2013-01-08 21:02 Cédric Girard
2013-01-08 21:46 ` Antti Palosaari
2013-01-08 22:10 ` Cédric Girard
2013-03-06 14:28 ` Cédric Girard
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.