From: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
To: Guenter Roeck <linux-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
Cc: Dmitry Torokhov
<dmitry.torokhov-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
LM Sensors <lm-sensors-GZX6beZjE8VD60Wz+7aTrA@public.gmane.org>,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org,
Corentin LABBE
<clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
linux-input-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Subject: Re: [lm-sensors] [PATCH v2 2/5] input: sun4i-ts: Add support for temperature sensor
Date: Tue, 31 Dec 2013 11:57:18 +0100 [thread overview]
Message-ID: <52C2A30E.5010705@redhat.com> (raw)
In-Reply-To: <20131227163419.GA20135-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
Hi,
On 12/27/2013 05:34 PM, Guenter Roeck wrote:
> On Fri, Dec 27, 2013 at 03:59:56PM +0100, Hans de Goede wrote:
>> The sun4i resisitive touchscreen controller also comes with a built-in
>> temperature sensor. This commit adds support for it.
>>
>> This commit also introduces a new "ts-attached" device-tree property,
>> when this is not set, the input part of the driver won't register. This way
>> the internal temperature sensor can be used to measure the SoC temperature
>> independent of there actually being a touchscreen attached to the controller.
>>
>> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
>
> Hi Hans,
>
> Almost good, except for a couple of nitpicks and one moe question.
> Assuming you fix the nitpicks and the question is not a concern,
> feel free to add
>
> Reviewed-by: Guenter Roeck <linux-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
>
> Guenter
>
>> ---
>> .../bindings/input/touchscreen/sun4i.txt | 6 +
>> drivers/input/touchscreen/sun4i-ts.c | 129 ++++++++++++++++-----
>> 2 files changed, 109 insertions(+), 26 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt
>> index e45927e..1fffd11 100644
>> --- a/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt
>> +++ b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt
>> @@ -6,10 +6,16 @@ Required properties:
>> - reg: mmio address range of the chip
>> - interrupts: interrupt to which the chip is connected
>>
>> +Optional properties:
>> + - ts-attached: boolean set this to tell the driver that an actual touchscreen
>> + is attached and that it should register an input device,
>> + without this it only registers the builtin temperate sensor
>> +
>> Example:
>>
>> rtp: rtp@01c25000 {
>> compatible = "allwinner,sun4i-ts";
>> reg = <0x01c25000 0x100>;
>> interrupts = <29>;
>> + ts-attached;
>> };
>> diff --git a/drivers/input/touchscreen/sun4i-ts.c b/drivers/input/touchscreen/sun4i-ts.c
>> index 10839d2..2d437f6 100644
>> --- a/drivers/input/touchscreen/sun4i-ts.c
>> +++ b/drivers/input/touchscreen/sun4i-ts.c
>> @@ -3,6 +3,9 @@
>> *
>> * Copyright (C) 2013 - 2014 Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
>> *
>> + * The hwmon parts are based on work by Corentin LABBE which is:
>> + * Copyright (C) 2013 Corentin LABBE <clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> + *
>> * This program is free software; you can redistribute it and/or modify
>> * it under the terms of the GNU General Public License as published by
>> * the Free Software Foundation; either version 2 of the License, or
>> @@ -30,6 +33,7 @@
>> */
>>
>> #include <linux/err.h>
>> +#include <linux/hwmon.h>
>> #include <linux/init.h>
>> #include <linux/input.h>
>> #include <linux/interrupt.h>
>> @@ -106,6 +110,7 @@ struct sun4i_ts_data {
>> void __iomem *base;
>> unsigned int irq;
>> bool ignore_fifo_data;
>> + int temp_data;
>> };
>>
>> static irqreturn_t sun4i_ts_irq(int irq, void *dev_id)
>> @@ -115,6 +120,12 @@ static irqreturn_t sun4i_ts_irq(int irq, void *dev_id)
>>
>> reg_val = readl(ts->base + TP_INT_FIFOS);
>>
>> + if (reg_val & TEMP_DATA_PENDING)
>> + ts->temp_data = readl(ts->base + TEMP_DATA);
>
> Is this read guaranteed to return 0 in the upper bit, or in other words is it
> guaranteed to never return 0xffffffff ? Otherwise there might be a problem with
> the implicit conversion to a negative integer.
Yes what is being read is a 12 bit unsigned value, with all the upper bits set to 0.
>
>> +
>> + if (!ts->input)
>> + goto leave;
>> +
>> if (reg_val & FIFO_DATA_PENDING) {
>> x = readl(ts->base + TP_DATA);
>> y = readl(ts->base + TP_DATA);
>> @@ -140,6 +151,7 @@ static irqreturn_t sun4i_ts_irq(int irq, void *dev_id)
>> input_sync(ts->input);
>> }
>>
>> +leave:
>> writel(reg_val, ts->base + TP_INT_FIFOS);
>>
>> return IRQ_HANDLED;
>> @@ -149,9 +161,9 @@ static int sun4i_ts_open(struct input_dev *dev)
>> {
>> struct sun4i_ts_data *ts = input_get_drvdata(dev);
>>
>> - /* Flush, set trig level to 1, enable data and up irqs */
>> - writel(DATA_IRQ_EN(1) | FIFO_TRIG(1) |FIFO_FLUSH(1) | TP_UP_IRQ_EN(1),
>> - ts->base + TP_INT_FIFOC);
>> + /* Flush, set trig level to 1, enable temp, data and up irqs */
>> + writel(TEMP_IRQ_EN(1) | DATA_IRQ_EN(1) | FIFO_TRIG(1) | FIFO_FLUSH(1) |
>> + TP_UP_IRQ_EN(1), ts->base + TP_INT_FIFOC);
>>
>> return 0;
>> }
>> @@ -160,40 +172,76 @@ static void sun4i_ts_close(struct input_dev *dev)
>> {
>> struct sun4i_ts_data *ts = input_get_drvdata(dev);
>>
>> - /* Deactivate all IRQs */
>> - writel(0, ts->base + TP_INT_FIFOC);
>> + /* Deactivate all input IRQs */
>> + writel(TEMP_IRQ_EN(1), ts->base + TP_INT_FIFOC);
>> synchronize_irq(ts->irq);
>> }
>>
>> +static ssize_t show_temp(struct device *dev, struct device_attribute *devattr,
>> + char *buf)
>> +{
>> + struct sun4i_ts_data *ts = dev_get_drvdata(dev);
>> +
>> + /* No temp_data until the first irq */
>> + if (ts->temp_data == -1)
>> + return -EAGAIN;
>> +
>> + return sprintf(buf, "%d\n", (ts->temp_data - 1447) * 100);
>> +}
>> +
>> +static ssize_t show_temp_label(struct device *dev,
>> + struct device_attribute *devattr, char *buf)
>> +{
>> + return sprintf(buf, "SoC temperature\n");
>> +}
>> +
>> +static DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL);
>> +static DEVICE_ATTR(temp1_label, S_IRUGO, show_temp_label, NULL);
>> +
>> +static struct attribute *sun4i_ts_attrs[] = {
>> + &dev_attr_temp1_input.attr,
>> + &dev_attr_temp1_label.attr,
>> + NULL
>> +};
>> +ATTRIBUTE_GROUPS(sun4i_ts);
>> +
>> static int sun4i_ts_probe(struct platform_device *pdev)
>> {
>> struct sun4i_ts_data *ts;
>> struct device *dev = &pdev->dev;
>> + struct device_node *np =dev->of_node;
>
> Missing space after '=' (checkpatch error).
>
>> + struct device *hwmon;
>> int ret;
>> + bool ts_attached;
>> +
>> + ts_attached = of_property_read_bool(np, "ts-attached");
>>
>> ts = devm_kzalloc(dev, sizeof(struct sun4i_ts_data), GFP_KERNEL);
>> if (!ts)
>> return -ENOMEM;
>>
>> ts->dev = dev;
>> -
>> - ts->input = devm_input_allocate_device(dev);
>> - if (!ts->input)
>> - return -ENOMEM;
>> -
>> - ts->input->name = pdev->name;
>> - ts->input->phys = "sun4i_ts/input0";
>> - ts->input->open = sun4i_ts_open;
>> - ts->input->close = sun4i_ts_close;
>> - ts->input->id.bustype = BUS_HOST;
>> - ts->input->id.vendor = 0x0001;
>> - ts->input->id.product = 0x0001;
>> - ts->input->id.version = 0x0100;
>> - ts->input->evbit[0] = BIT(EV_SYN) | BIT(EV_KEY) | BIT(EV_ABS);
>> - set_bit(BTN_TOUCH, ts->input->keybit);
>> - input_set_abs_params(ts->input, ABS_X, 0, 4095, 0, 0);
>> - input_set_abs_params(ts->input, ABS_Y, 0, 4095, 0, 0);
>> - input_set_drvdata(ts->input, ts);
>> + ts->temp_data = -1;
>> +
>> + if (ts_attached) {
>> + ts->input = devm_input_allocate_device(dev);
>> + if (!ts->input)
>> + return -ENOMEM;
>> +
>> + ts->input->name = pdev->name;
>> + ts->input->phys = "sun4i_ts/input0";
>> + ts->input->open = sun4i_ts_open;
>> + ts->input->close = sun4i_ts_close;
>> + ts->input->id.bustype = BUS_HOST;
>> + ts->input->id.vendor = 0x0001;
>> + ts->input->id.product = 0x0001;
>> + ts->input->id.version = 0x0100;
>> + ts->input->evbit[0] = BIT(EV_SYN) | BIT(EV_KEY) | BIT(EV_ABS);
>> + set_bit(BTN_TOUCH, ts->input->keybit);
>> + input_set_abs_params(ts->input, ABS_X, 0, 4095, 0, 0);
>> + input_set_abs_params(ts->input, ABS_Y, 0, 4095, 0, 0);
>> + input_set_drvdata(ts->input, ts);
>> + }
>>
>> ts->base = devm_ioremap_resource(dev,
>> platform_get_resource(pdev, IORESOURCE_MEM, 0));
>> @@ -232,14 +280,42 @@ static int sun4i_ts_probe(struct platform_device *pdev)
>> writel(STYLUS_UP_DEBOUN(5) | STYLUS_UP_DEBOUN_EN(1) | TP_MODE_EN(1),
>> ts->base + TP_CTRL1);
>>
>> - ret = input_register_device(ts->input);
>> - if (ret)
>> - return ret;
>> + hwmon = devm_hwmon_device_register_with_groups(ts->dev, "sun4i_ts",
>> + ts, sun4i_ts_groups);
>> + if (IS_ERR(hwmon)) {
>> + return PTR_ERR(hwmon);
>> + }
>
> { } are not needed here (checkpatch warning).
Oops, should have run checkpatch on v2 too, my bad. Both fixed now.
Regards,
Hans
WARNING: multiple messages have this Message-ID (diff)
From: Hans de Goede <hdegoede@redhat.com>
To: Guenter Roeck <linux-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
Cc: Dmitry Torokhov
<dmitry.torokhov-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
LM Sensors <lm-sensors-GZX6beZjE8VD60Wz+7aTrA@public.gmane.org>,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org,
Corentin LABBE
<clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
linux-input-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Subject: Re: [lm-sensors] [PATCH v2 2/5] input: sun4i-ts: Add support for temperature sensor
Date: Tue, 31 Dec 2013 10:57:18 +0000 [thread overview]
Message-ID: <52C2A30E.5010705@redhat.com> (raw)
In-Reply-To: <20131227163419.GA20135-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
Hi,
On 12/27/2013 05:34 PM, Guenter Roeck wrote:
> On Fri, Dec 27, 2013 at 03:59:56PM +0100, Hans de Goede wrote:
>> The sun4i resisitive touchscreen controller also comes with a built-in
>> temperature sensor. This commit adds support for it.
>>
>> This commit also introduces a new "ts-attached" device-tree property,
>> when this is not set, the input part of the driver won't register. This way
>> the internal temperature sensor can be used to measure the SoC temperature
>> independent of there actually being a touchscreen attached to the controller.
>>
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>
> Hi Hans,
>
> Almost good, except for a couple of nitpicks and one moe question.
> Assuming you fix the nitpicks and the question is not a concern,
> feel free to add
>
> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
>
> Guenter
>
>> ---
>> .../bindings/input/touchscreen/sun4i.txt | 6 +
>> drivers/input/touchscreen/sun4i-ts.c | 129 ++++++++++++++++-----
>> 2 files changed, 109 insertions(+), 26 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt
>> index e45927e..1fffd11 100644
>> --- a/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt
>> +++ b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt
>> @@ -6,10 +6,16 @@ Required properties:
>> - reg: mmio address range of the chip
>> - interrupts: interrupt to which the chip is connected
>>
>> +Optional properties:
>> + - ts-attached: boolean set this to tell the driver that an actual touchscreen
>> + is attached and that it should register an input device,
>> + without this it only registers the builtin temperate sensor
>> +
>> Example:
>>
>> rtp: rtp@01c25000 {
>> compatible = "allwinner,sun4i-ts";
>> reg = <0x01c25000 0x100>;
>> interrupts = <29>;
>> + ts-attached;
>> };
>> diff --git a/drivers/input/touchscreen/sun4i-ts.c b/drivers/input/touchscreen/sun4i-ts.c
>> index 10839d2..2d437f6 100644
>> --- a/drivers/input/touchscreen/sun4i-ts.c
>> +++ b/drivers/input/touchscreen/sun4i-ts.c
>> @@ -3,6 +3,9 @@
>> *
>> * Copyright (C) 2013 - 2014 Hans de Goede <hdegoede@redhat.com>
>> *
>> + * The hwmon parts are based on work by Corentin LABBE which is:
>> + * Copyright (C) 2013 Corentin LABBE <clabbe.montjoie@gmail.com>
>> + *
>> * This program is free software; you can redistribute it and/or modify
>> * it under the terms of the GNU General Public License as published by
>> * the Free Software Foundation; either version 2 of the License, or
>> @@ -30,6 +33,7 @@
>> */
>>
>> #include <linux/err.h>
>> +#include <linux/hwmon.h>
>> #include <linux/init.h>
>> #include <linux/input.h>
>> #include <linux/interrupt.h>
>> @@ -106,6 +110,7 @@ struct sun4i_ts_data {
>> void __iomem *base;
>> unsigned int irq;
>> bool ignore_fifo_data;
>> + int temp_data;
>> };
>>
>> static irqreturn_t sun4i_ts_irq(int irq, void *dev_id)
>> @@ -115,6 +120,12 @@ static irqreturn_t sun4i_ts_irq(int irq, void *dev_id)
>>
>> reg_val = readl(ts->base + TP_INT_FIFOS);
>>
>> + if (reg_val & TEMP_DATA_PENDING)
>> + ts->temp_data = readl(ts->base + TEMP_DATA);
>
> Is this read guaranteed to return 0 in the upper bit, or in other words is it
> guaranteed to never return 0xffffffff ? Otherwise there might be a problem with
> the implicit conversion to a negative integer.
Yes what is being read is a 12 bit unsigned value, with all the upper bits set to 0.
>
>> +
>> + if (!ts->input)
>> + goto leave;
>> +
>> if (reg_val & FIFO_DATA_PENDING) {
>> x = readl(ts->base + TP_DATA);
>> y = readl(ts->base + TP_DATA);
>> @@ -140,6 +151,7 @@ static irqreturn_t sun4i_ts_irq(int irq, void *dev_id)
>> input_sync(ts->input);
>> }
>>
>> +leave:
>> writel(reg_val, ts->base + TP_INT_FIFOS);
>>
>> return IRQ_HANDLED;
>> @@ -149,9 +161,9 @@ static int sun4i_ts_open(struct input_dev *dev)
>> {
>> struct sun4i_ts_data *ts = input_get_drvdata(dev);
>>
>> - /* Flush, set trig level to 1, enable data and up irqs */
>> - writel(DATA_IRQ_EN(1) | FIFO_TRIG(1) |FIFO_FLUSH(1) | TP_UP_IRQ_EN(1),
>> - ts->base + TP_INT_FIFOC);
>> + /* Flush, set trig level to 1, enable temp, data and up irqs */
>> + writel(TEMP_IRQ_EN(1) | DATA_IRQ_EN(1) | FIFO_TRIG(1) | FIFO_FLUSH(1) |
>> + TP_UP_IRQ_EN(1), ts->base + TP_INT_FIFOC);
>>
>> return 0;
>> }
>> @@ -160,40 +172,76 @@ static void sun4i_ts_close(struct input_dev *dev)
>> {
>> struct sun4i_ts_data *ts = input_get_drvdata(dev);
>>
>> - /* Deactivate all IRQs */
>> - writel(0, ts->base + TP_INT_FIFOC);
>> + /* Deactivate all input IRQs */
>> + writel(TEMP_IRQ_EN(1), ts->base + TP_INT_FIFOC);
>> synchronize_irq(ts->irq);
>> }
>>
>> +static ssize_t show_temp(struct device *dev, struct device_attribute *devattr,
>> + char *buf)
>> +{
>> + struct sun4i_ts_data *ts = dev_get_drvdata(dev);
>> +
>> + /* No temp_data until the first irq */
>> + if (ts->temp_data = -1)
>> + return -EAGAIN;
>> +
>> + return sprintf(buf, "%d\n", (ts->temp_data - 1447) * 100);
>> +}
>> +
>> +static ssize_t show_temp_label(struct device *dev,
>> + struct device_attribute *devattr, char *buf)
>> +{
>> + return sprintf(buf, "SoC temperature\n");
>> +}
>> +
>> +static DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL);
>> +static DEVICE_ATTR(temp1_label, S_IRUGO, show_temp_label, NULL);
>> +
>> +static struct attribute *sun4i_ts_attrs[] = {
>> + &dev_attr_temp1_input.attr,
>> + &dev_attr_temp1_label.attr,
>> + NULL
>> +};
>> +ATTRIBUTE_GROUPS(sun4i_ts);
>> +
>> static int sun4i_ts_probe(struct platform_device *pdev)
>> {
>> struct sun4i_ts_data *ts;
>> struct device *dev = &pdev->dev;
>> + struct device_node *np Þv->of_node;
>
> Missing space after '=' (checkpatch error).
>
>> + struct device *hwmon;
>> int ret;
>> + bool ts_attached;
>> +
>> + ts_attached = of_property_read_bool(np, "ts-attached");
>>
>> ts = devm_kzalloc(dev, sizeof(struct sun4i_ts_data), GFP_KERNEL);
>> if (!ts)
>> return -ENOMEM;
>>
>> ts->dev = dev;
>> -
>> - ts->input = devm_input_allocate_device(dev);
>> - if (!ts->input)
>> - return -ENOMEM;
>> -
>> - ts->input->name = pdev->name;
>> - ts->input->phys = "sun4i_ts/input0";
>> - ts->input->open = sun4i_ts_open;
>> - ts->input->close = sun4i_ts_close;
>> - ts->input->id.bustype = BUS_HOST;
>> - ts->input->id.vendor = 0x0001;
>> - ts->input->id.product = 0x0001;
>> - ts->input->id.version = 0x0100;
>> - ts->input->evbit[0] = BIT(EV_SYN) | BIT(EV_KEY) | BIT(EV_ABS);
>> - set_bit(BTN_TOUCH, ts->input->keybit);
>> - input_set_abs_params(ts->input, ABS_X, 0, 4095, 0, 0);
>> - input_set_abs_params(ts->input, ABS_Y, 0, 4095, 0, 0);
>> - input_set_drvdata(ts->input, ts);
>> + ts->temp_data = -1;
>> +
>> + if (ts_attached) {
>> + ts->input = devm_input_allocate_device(dev);
>> + if (!ts->input)
>> + return -ENOMEM;
>> +
>> + ts->input->name = pdev->name;
>> + ts->input->phys = "sun4i_ts/input0";
>> + ts->input->open = sun4i_ts_open;
>> + ts->input->close = sun4i_ts_close;
>> + ts->input->id.bustype = BUS_HOST;
>> + ts->input->id.vendor = 0x0001;
>> + ts->input->id.product = 0x0001;
>> + ts->input->id.version = 0x0100;
>> + ts->input->evbit[0] = BIT(EV_SYN) | BIT(EV_KEY) | BIT(EV_ABS);
>> + set_bit(BTN_TOUCH, ts->input->keybit);
>> + input_set_abs_params(ts->input, ABS_X, 0, 4095, 0, 0);
>> + input_set_abs_params(ts->input, ABS_Y, 0, 4095, 0, 0);
>> + input_set_drvdata(ts->input, ts);
>> + }
>>
>> ts->base = devm_ioremap_resource(dev,
>> platform_get_resource(pdev, IORESOURCE_MEM, 0));
>> @@ -232,14 +280,42 @@ static int sun4i_ts_probe(struct platform_device *pdev)
>> writel(STYLUS_UP_DEBOUN(5) | STYLUS_UP_DEBOUN_EN(1) | TP_MODE_EN(1),
>> ts->base + TP_CTRL1);
>>
>> - ret = input_register_device(ts->input);
>> - if (ret)
>> - return ret;
>> + hwmon = devm_hwmon_device_register_with_groups(ts->dev, "sun4i_ts",
>> + ts, sun4i_ts_groups);
>> + if (IS_ERR(hwmon)) {
>> + return PTR_ERR(hwmon);
>> + }
>
> { } are not needed here (checkpatch warning).
Oops, should have run checkpatch on v2 too, my bad. Both fixed now.
Regards,
Hans
_______________________________________________
lm-sensors mailing list
lm-sensors@lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
WARNING: multiple messages have this Message-ID (diff)
From: hdegoede@redhat.com (Hans de Goede)
To: linux-arm-kernel@lists.infradead.org
Subject: [lm-sensors] [PATCH v2 2/5] input: sun4i-ts: Add support for temperature sensor
Date: Tue, 31 Dec 2013 11:57:18 +0100 [thread overview]
Message-ID: <52C2A30E.5010705@redhat.com> (raw)
In-Reply-To: <20131227163419.GA20135@roeck-us.net>
Hi,
On 12/27/2013 05:34 PM, Guenter Roeck wrote:
> On Fri, Dec 27, 2013 at 03:59:56PM +0100, Hans de Goede wrote:
>> The sun4i resisitive touchscreen controller also comes with a built-in
>> temperature sensor. This commit adds support for it.
>>
>> This commit also introduces a new "ts-attached" device-tree property,
>> when this is not set, the input part of the driver won't register. This way
>> the internal temperature sensor can be used to measure the SoC temperature
>> independent of there actually being a touchscreen attached to the controller.
>>
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>
> Hi Hans,
>
> Almost good, except for a couple of nitpicks and one moe question.
> Assuming you fix the nitpicks and the question is not a concern,
> feel free to add
>
> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
>
> Guenter
>
>> ---
>> .../bindings/input/touchscreen/sun4i.txt | 6 +
>> drivers/input/touchscreen/sun4i-ts.c | 129 ++++++++++++++++-----
>> 2 files changed, 109 insertions(+), 26 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt
>> index e45927e..1fffd11 100644
>> --- a/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt
>> +++ b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt
>> @@ -6,10 +6,16 @@ Required properties:
>> - reg: mmio address range of the chip
>> - interrupts: interrupt to which the chip is connected
>>
>> +Optional properties:
>> + - ts-attached: boolean set this to tell the driver that an actual touchscreen
>> + is attached and that it should register an input device,
>> + without this it only registers the builtin temperate sensor
>> +
>> Example:
>>
>> rtp: rtp at 01c25000 {
>> compatible = "allwinner,sun4i-ts";
>> reg = <0x01c25000 0x100>;
>> interrupts = <29>;
>> + ts-attached;
>> };
>> diff --git a/drivers/input/touchscreen/sun4i-ts.c b/drivers/input/touchscreen/sun4i-ts.c
>> index 10839d2..2d437f6 100644
>> --- a/drivers/input/touchscreen/sun4i-ts.c
>> +++ b/drivers/input/touchscreen/sun4i-ts.c
>> @@ -3,6 +3,9 @@
>> *
>> * Copyright (C) 2013 - 2014 Hans de Goede <hdegoede@redhat.com>
>> *
>> + * The hwmon parts are based on work by Corentin LABBE which is:
>> + * Copyright (C) 2013 Corentin LABBE <clabbe.montjoie@gmail.com>
>> + *
>> * This program is free software; you can redistribute it and/or modify
>> * it under the terms of the GNU General Public License as published by
>> * the Free Software Foundation; either version 2 of the License, or
>> @@ -30,6 +33,7 @@
>> */
>>
>> #include <linux/err.h>
>> +#include <linux/hwmon.h>
>> #include <linux/init.h>
>> #include <linux/input.h>
>> #include <linux/interrupt.h>
>> @@ -106,6 +110,7 @@ struct sun4i_ts_data {
>> void __iomem *base;
>> unsigned int irq;
>> bool ignore_fifo_data;
>> + int temp_data;
>> };
>>
>> static irqreturn_t sun4i_ts_irq(int irq, void *dev_id)
>> @@ -115,6 +120,12 @@ static irqreturn_t sun4i_ts_irq(int irq, void *dev_id)
>>
>> reg_val = readl(ts->base + TP_INT_FIFOS);
>>
>> + if (reg_val & TEMP_DATA_PENDING)
>> + ts->temp_data = readl(ts->base + TEMP_DATA);
>
> Is this read guaranteed to return 0 in the upper bit, or in other words is it
> guaranteed to never return 0xffffffff ? Otherwise there might be a problem with
> the implicit conversion to a negative integer.
Yes what is being read is a 12 bit unsigned value, with all the upper bits set to 0.
>
>> +
>> + if (!ts->input)
>> + goto leave;
>> +
>> if (reg_val & FIFO_DATA_PENDING) {
>> x = readl(ts->base + TP_DATA);
>> y = readl(ts->base + TP_DATA);
>> @@ -140,6 +151,7 @@ static irqreturn_t sun4i_ts_irq(int irq, void *dev_id)
>> input_sync(ts->input);
>> }
>>
>> +leave:
>> writel(reg_val, ts->base + TP_INT_FIFOS);
>>
>> return IRQ_HANDLED;
>> @@ -149,9 +161,9 @@ static int sun4i_ts_open(struct input_dev *dev)
>> {
>> struct sun4i_ts_data *ts = input_get_drvdata(dev);
>>
>> - /* Flush, set trig level to 1, enable data and up irqs */
>> - writel(DATA_IRQ_EN(1) | FIFO_TRIG(1) |FIFO_FLUSH(1) | TP_UP_IRQ_EN(1),
>> - ts->base + TP_INT_FIFOC);
>> + /* Flush, set trig level to 1, enable temp, data and up irqs */
>> + writel(TEMP_IRQ_EN(1) | DATA_IRQ_EN(1) | FIFO_TRIG(1) | FIFO_FLUSH(1) |
>> + TP_UP_IRQ_EN(1), ts->base + TP_INT_FIFOC);
>>
>> return 0;
>> }
>> @@ -160,40 +172,76 @@ static void sun4i_ts_close(struct input_dev *dev)
>> {
>> struct sun4i_ts_data *ts = input_get_drvdata(dev);
>>
>> - /* Deactivate all IRQs */
>> - writel(0, ts->base + TP_INT_FIFOC);
>> + /* Deactivate all input IRQs */
>> + writel(TEMP_IRQ_EN(1), ts->base + TP_INT_FIFOC);
>> synchronize_irq(ts->irq);
>> }
>>
>> +static ssize_t show_temp(struct device *dev, struct device_attribute *devattr,
>> + char *buf)
>> +{
>> + struct sun4i_ts_data *ts = dev_get_drvdata(dev);
>> +
>> + /* No temp_data until the first irq */
>> + if (ts->temp_data == -1)
>> + return -EAGAIN;
>> +
>> + return sprintf(buf, "%d\n", (ts->temp_data - 1447) * 100);
>> +}
>> +
>> +static ssize_t show_temp_label(struct device *dev,
>> + struct device_attribute *devattr, char *buf)
>> +{
>> + return sprintf(buf, "SoC temperature\n");
>> +}
>> +
>> +static DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL);
>> +static DEVICE_ATTR(temp1_label, S_IRUGO, show_temp_label, NULL);
>> +
>> +static struct attribute *sun4i_ts_attrs[] = {
>> + &dev_attr_temp1_input.attr,
>> + &dev_attr_temp1_label.attr,
>> + NULL
>> +};
>> +ATTRIBUTE_GROUPS(sun4i_ts);
>> +
>> static int sun4i_ts_probe(struct platform_device *pdev)
>> {
>> struct sun4i_ts_data *ts;
>> struct device *dev = &pdev->dev;
>> + struct device_node *np =dev->of_node;
>
> Missing space after '=' (checkpatch error).
>
>> + struct device *hwmon;
>> int ret;
>> + bool ts_attached;
>> +
>> + ts_attached = of_property_read_bool(np, "ts-attached");
>>
>> ts = devm_kzalloc(dev, sizeof(struct sun4i_ts_data), GFP_KERNEL);
>> if (!ts)
>> return -ENOMEM;
>>
>> ts->dev = dev;
>> -
>> - ts->input = devm_input_allocate_device(dev);
>> - if (!ts->input)
>> - return -ENOMEM;
>> -
>> - ts->input->name = pdev->name;
>> - ts->input->phys = "sun4i_ts/input0";
>> - ts->input->open = sun4i_ts_open;
>> - ts->input->close = sun4i_ts_close;
>> - ts->input->id.bustype = BUS_HOST;
>> - ts->input->id.vendor = 0x0001;
>> - ts->input->id.product = 0x0001;
>> - ts->input->id.version = 0x0100;
>> - ts->input->evbit[0] = BIT(EV_SYN) | BIT(EV_KEY) | BIT(EV_ABS);
>> - set_bit(BTN_TOUCH, ts->input->keybit);
>> - input_set_abs_params(ts->input, ABS_X, 0, 4095, 0, 0);
>> - input_set_abs_params(ts->input, ABS_Y, 0, 4095, 0, 0);
>> - input_set_drvdata(ts->input, ts);
>> + ts->temp_data = -1;
>> +
>> + if (ts_attached) {
>> + ts->input = devm_input_allocate_device(dev);
>> + if (!ts->input)
>> + return -ENOMEM;
>> +
>> + ts->input->name = pdev->name;
>> + ts->input->phys = "sun4i_ts/input0";
>> + ts->input->open = sun4i_ts_open;
>> + ts->input->close = sun4i_ts_close;
>> + ts->input->id.bustype = BUS_HOST;
>> + ts->input->id.vendor = 0x0001;
>> + ts->input->id.product = 0x0001;
>> + ts->input->id.version = 0x0100;
>> + ts->input->evbit[0] = BIT(EV_SYN) | BIT(EV_KEY) | BIT(EV_ABS);
>> + set_bit(BTN_TOUCH, ts->input->keybit);
>> + input_set_abs_params(ts->input, ABS_X, 0, 4095, 0, 0);
>> + input_set_abs_params(ts->input, ABS_Y, 0, 4095, 0, 0);
>> + input_set_drvdata(ts->input, ts);
>> + }
>>
>> ts->base = devm_ioremap_resource(dev,
>> platform_get_resource(pdev, IORESOURCE_MEM, 0));
>> @@ -232,14 +280,42 @@ static int sun4i_ts_probe(struct platform_device *pdev)
>> writel(STYLUS_UP_DEBOUN(5) | STYLUS_UP_DEBOUN_EN(1) | TP_MODE_EN(1),
>> ts->base + TP_CTRL1);
>>
>> - ret = input_register_device(ts->input);
>> - if (ret)
>> - return ret;
>> + hwmon = devm_hwmon_device_register_with_groups(ts->dev, "sun4i_ts",
>> + ts, sun4i_ts_groups);
>> + if (IS_ERR(hwmon)) {
>> + return PTR_ERR(hwmon);
>> + }
>
> { } are not needed here (checkpatch warning).
Oops, should have run checkpatch on v2 too, my bad. Both fixed now.
Regards,
Hans
next prev parent reply other threads:[~2013-12-31 10:57 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-12-27 14:59 [PATCH v2 0/5] input: Add new sun4i-ts driver for Allwinner sunxi Hans de Goede
2013-12-27 14:59 ` Hans de Goede
2013-12-27 14:59 ` [lm-sensors] " Hans de Goede
[not found] ` <1388156399-29677-1-git-send-email-hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
2013-12-27 14:59 ` [PATCH v2 1/5] input: Add new sun4i-ts driver for Allwinner sunxi SoC's rtp controller Hans de Goede
2013-12-27 14:59 ` Hans de Goede
2013-12-27 14:59 ` [lm-sensors] " Hans de Goede
2013-12-27 14:59 ` [PATCH v2 2/5] input: sun4i-ts: Add support for temperature sensor Hans de Goede
2013-12-27 14:59 ` Hans de Goede
2013-12-27 14:59 ` [lm-sensors] " Hans de Goede
[not found] ` <1388156399-29677-3-git-send-email-hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
2013-12-27 16:34 ` Guenter Roeck
2013-12-27 16:34 ` Guenter Roeck
2013-12-27 16:34 ` Guenter Roeck
[not found] ` <20131227163419.GA20135-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
2013-12-31 10:57 ` Hans de Goede [this message]
2013-12-31 10:57 ` Hans de Goede
2013-12-31 10:57 ` Hans de Goede
2013-12-28 1:10 ` Dmitry Torokhov
2013-12-28 1:10 ` Dmitry Torokhov
2013-12-28 1:10 ` [lm-sensors] " Dmitry Torokhov
[not found] ` <20131228011007.GA14188-WlK9ik9hQGAhIp7JRqBPierSzoNAToWh@public.gmane.org>
2013-12-31 11:10 ` Hans de Goede
2013-12-31 11:10 ` Hans de Goede
2013-12-31 11:10 ` [lm-sensors] " Hans de Goede
2013-12-28 1:13 ` Dmitry Torokhov
2013-12-28 1:13 ` Dmitry Torokhov
2013-12-28 1:13 ` [lm-sensors] " Dmitry Torokhov
[not found] ` <20131228011304.GB14188-WlK9ik9hQGAhIp7JRqBPierSzoNAToWh@public.gmane.org>
2013-12-31 11:17 ` Hans de Goede
2013-12-31 11:17 ` Hans de Goede
2013-12-31 11:17 ` [lm-sensors] " Hans de Goede
2013-12-31 13:00 ` Maxime Ripard
2013-12-31 13:00 ` Maxime Ripard
2013-12-31 13:00 ` [lm-sensors] " Maxime Ripard
2013-12-31 15:02 ` Hans de Goede
2013-12-31 15:02 ` Hans de Goede
2013-12-31 15:02 ` [lm-sensors] " Hans de Goede
2013-12-27 14:59 ` [PATCH v2 3/5] ARM: dts: sun4i: Add rtp controller node Hans de Goede
2013-12-27 14:59 ` Hans de Goede
2013-12-27 14:59 ` [lm-sensors] " Hans de Goede
2013-12-27 14:59 ` [PATCH v2 4/5] ARM: dts: sun5i: " Hans de Goede
2013-12-27 14:59 ` Hans de Goede
2013-12-27 14:59 ` [lm-sensors] " Hans de Goede
2013-12-27 14:59 ` [PATCH v2 5/5] ARM: dts: sun7i: " Hans de Goede
2013-12-27 14:59 ` Hans de Goede
2013-12-27 14:59 ` [lm-sensors] " Hans de Goede
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=52C2A30E.5010705@redhat.com \
--to=hdegoede-h+wxahxf7alqt0dzr+alfa@public.gmane.org \
--cc=clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=dmitry.torokhov-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=linux-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-input-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org \
--cc=lm-sensors-GZX6beZjE8VD60Wz+7aTrA@public.gmane.org \
--cc=maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.