From: Tomasz Figa <tomasz.figa@gmail.com>
To: Rahul Sharma <rahul.sharma@samsung.com>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-samsung-soc@vger.kernel.org
Cc: kgene.kim@samsung.com, inki.dae@samsung.com, joshi@samsung.com,
r.sh.open@gmail.com
Subject: Re: [PATCH v4 5/5] ARM: dts: enable hdmi for exynos5800 based peach-pi board
Date: Wed, 14 May 2014 21:57:43 +0200 [thread overview]
Message-ID: <5373CAB7.3040002@gmail.com> (raw)
In-Reply-To: <5373CA74.8080500@gmail.com>
On 14.05.2014 21:56, Tomasz Figa wrote:
> Hi Rahul,
>
> On 14.05.2014 04:46, Rahul Sharma wrote:
>> From: Rahul Sharma <Rahul.Sharma@samsung.com>
>>
>> Enable hdmi for peach-pi board.
>>
>> Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
>> ---
>> arch/arm/boot/dts/exynos5800-peach-pi.dts | 19 +++++++++++++++++++
>> 1 file changed, 19 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> index 742655b..2a6f23b8 100644
>> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> @@ -134,6 +134,25 @@
>> };
>> };
>>
>> +&i2c_2 {
>> + status = "okay";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <66000>;
>> + samsung,i2c-slave-addr = <0x50>;
>> +
>> + hdmiddc@50 {
>> + reg = <0x50>;
>> + };
Aha, also with the new Exynos HDMI bindings, I don't think the DDC
device node is necessary any longer.
Best regards,
Tomasz
WARNING: multiple messages have this Message-ID (diff)
From: tomasz.figa@gmail.com (Tomasz Figa)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v4 5/5] ARM: dts: enable hdmi for exynos5800 based peach-pi board
Date: Wed, 14 May 2014 21:57:43 +0200 [thread overview]
Message-ID: <5373CAB7.3040002@gmail.com> (raw)
In-Reply-To: <5373CA74.8080500@gmail.com>
On 14.05.2014 21:56, Tomasz Figa wrote:
> Hi Rahul,
>
> On 14.05.2014 04:46, Rahul Sharma wrote:
>> From: Rahul Sharma <Rahul.Sharma@samsung.com>
>>
>> Enable hdmi for peach-pi board.
>>
>> Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
>> ---
>> arch/arm/boot/dts/exynos5800-peach-pi.dts | 19 +++++++++++++++++++
>> 1 file changed, 19 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> index 742655b..2a6f23b8 100644
>> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> @@ -134,6 +134,25 @@
>> };
>> };
>>
>> +&i2c_2 {
>> + status = "okay";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <66000>;
>> + samsung,i2c-slave-addr = <0x50>;
>> +
>> + hdmiddc at 50 {
>> + reg = <0x50>;
>> + };
Aha, also with the new Exynos HDMI bindings, I don't think the DDC
device node is necessary any longer.
Best regards,
Tomasz
next prev parent reply other threads:[~2014-05-14 19:57 UTC|newest]
Thread overview: 38+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-14 2:45 [PATCH v4 0/5] ARM: dts: enable hdmi for exynos5 based peach and snow boards Rahul Sharma
2014-05-14 2:45 ` Rahul Sharma
2014-05-14 2:45 ` [PATCH v4 1/5] ARM: dts: enable hdmi for exynos5250 based snow board Rahul Sharma
2014-05-14 2:45 ` Rahul Sharma
2014-05-14 19:41 ` Tomasz Figa
2014-05-14 19:41 ` Tomasz Figa
2014-05-15 5:22 ` Rahul Sharma
2014-05-15 5:22 ` Rahul Sharma
2014-05-14 2:45 ` [PATCH v4 2/5] ARM: dts: change to correct compatible string for exynos5420 hdmi Rahul Sharma
2014-05-14 2:45 ` Rahul Sharma
2014-05-14 19:44 ` Tomasz Figa
2014-05-14 19:44 ` Tomasz Figa
2014-05-15 5:25 ` Rahul Sharma
2014-05-15 5:25 ` Rahul Sharma
2014-05-14 2:46 ` [PATCH v4 3/5] ARM: dts: enable hdmi for exynos5420 based peach-pit board Rahul Sharma
2014-05-14 2:46 ` Rahul Sharma
2014-05-14 19:50 ` Tomasz Figa
2014-05-14 19:50 ` Tomasz Figa
2014-05-15 5:46 ` Rahul Sharma
2014-05-15 5:46 ` Rahul Sharma
2014-05-14 2:46 ` [PATCH v4 4/5] ARM: dts: remove chip specific hdmi hpd pin from board Rahul Sharma
2014-05-14 2:46 ` Rahul Sharma
2014-05-14 18:45 ` Kukjin Kim
2014-05-14 18:45 ` Kukjin Kim
2014-05-14 19:23 ` Rahul Sharma
2014-05-14 19:23 ` Rahul Sharma
2014-05-14 19:51 ` Tomasz Figa
2014-05-14 19:51 ` Tomasz Figa
2014-05-15 5:47 ` Rahul Sharma
2014-05-15 5:47 ` Rahul Sharma
2014-05-14 2:46 ` [PATCH v4 5/5] ARM: dts: enable hdmi for exynos5800 based peach-pi board Rahul Sharma
2014-05-14 2:46 ` Rahul Sharma
2014-05-14 19:56 ` Tomasz Figa
2014-05-14 19:56 ` Tomasz Figa
2014-05-14 19:57 ` Tomasz Figa [this message]
2014-05-14 19:57 ` Tomasz Figa
2014-05-15 8:27 ` Rahul Sharma
2014-05-15 8:27 ` Rahul Sharma
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5373CAB7.3040002@gmail.com \
--to=tomasz.figa@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=inki.dae@samsung.com \
--cc=joshi@samsung.com \
--cc=kgene.kim@samsung.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=r.sh.open@gmail.com \
--cc=rahul.sharma@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.