Re: [PATCH 1/2] net: davinci_mdio: reuse for keystone2 arch

[Santosh Shilimkar <santosh.shilimkar@ti.com>]

On Wednesday 09 July 2014 09:10 AM, Grygorii Strashko wrote:
> The similar MDIO HW blocks is used by keystone 2 SoCs as
> in Davinci SoCs:
> - one in Gigabit Ethernet (GbE) Switch Subsystem
>   See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
> - one in 10 Gigabit Ethernet Subsystem
>   See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf
> 
> Hence, reuse Davinci MDIO driver for Keystone 2 and
> enable TI networking for Keystone 2 devices
> 
> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
> ---
Looks good to me.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

>  .../devicetree/bindings/net/davinci-mdio.txt       |    8 ++++----
>  drivers/net/ethernet/ti/Kconfig                    |    4 ++--
>  2 files changed, 6 insertions(+), 6 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
> index 72efaaf..d2e68e7 100644
> --- a/Documentation/devicetree/bindings/net/davinci-mdio.txt
> +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
> @@ -1,8 +1,8 @@
> -TI SoC Davinci MDIO Controller Device Tree Bindings
> +TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings
>  ---------------------------------------------------
>  
>  Required properties:
> -- compatible		: Should be "ti,davinci_mdio"
> +- compatible		: Should be "ti,davinci_mdio" or "ti,keystone-mdio"
>  - reg			: physical base address and size of the davinci mdio
>  			  registers map
>  - bus_freq		: Mdio Bus frequency
> @@ -19,7 +19,7 @@ file.
>  Examples:
>  
>  	mdio: davinci_mdio@4A101000 {
> -		compatible = "ti,cpsw";
> +		compatible = "ti,davinci_mdio";
>  		reg = <0x4A101000 0x1000>;
>  		bus_freq = <1000000>;
>  	};
> @@ -27,7 +27,7 @@ Examples:
>  (or)
>  
>  	mdio: davinci_mdio@4A101000 {
> -		compatible = "ti,cpsw";
> +		compatible = "ti,davinci_mdio";
>  		ti,hwmods = "davinci_mdio";
>  		bus_freq = <1000000>;
>  	};
> diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
> index 53150c2..1769700 100644
> --- a/drivers/net/ethernet/ti/Kconfig
> +++ b/drivers/net/ethernet/ti/Kconfig
> @@ -5,7 +5,7 @@
>  config NET_VENDOR_TI
>  	bool "Texas Instruments (TI) devices"
>  	default y
> -	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX))
> +	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE))
>  	---help---
>  	  If you have a network (Ethernet) card belonging to this class, say Y
>  	  and read the Ethernet-HOWTO, available from
> @@ -32,7 +32,7 @@ config TI_DAVINCI_EMAC
>  
>  config TI_DAVINCI_MDIO
>  	tristate "TI DaVinci MDIO Support"
> -	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX )
> +	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE )
>  	select PHYLIB
>  	---help---
>  	  This driver supports TI's DaVinci MDIO module.
>