[PATCH v2 6/9] ARM: berlin: Add BG2 ethernet DT nodes

[sebastian.hesselbarth@gmail.com (Sebastian Hesselbarth)]

On 22.10.2014 20:26, Sebastian Hesselbarth wrote:
> Marvell BG2 has two fast ethernet controllers with internal PHY,
> add the corresponding nodes to SoC dtsi.
>
> Tested-by: Antoine T?nart <antoine.tenart@free-electrons.com>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

Applied the four DT patches to berlin/dt.

Sebastian

> ---
> Changelog:
> v1->v2:
> - move phy-connection-type to controller node instead of PHY node
>    (Reported by Sergei Shtylyov)
>
> Cc: "David S. Miller" <davem@davemloft.net>
> Cc: "Antoine T?nart" <antoine.tenart@free-electrons.com>
> Cc: Florian Fainelli <f.fainelli@gmail.com>
> Cc: Eric Miao <eric.y.miao@gmail.com>
> Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: netdev at vger.kernel.org
> Cc: devicetree at vger.kernel.org
> Cc: linux-kernel at vger.kernel.org
> ---
>   arch/arm/boot/dts/berlin2.dtsi | 36 ++++++++++++++++++++++++++++++++++++
>   1 file changed, 36 insertions(+)
>
> diff --git a/arch/arm/boot/dts/berlin2.dtsi b/arch/arm/boot/dts/berlin2.dtsi
> index 9d7c810ebd0b..dc0227dfc691 100644
> --- a/arch/arm/boot/dts/berlin2.dtsi
> +++ b/arch/arm/boot/dts/berlin2.dtsi
> @@ -79,11 +79,47 @@
>   			clocks = <&chip CLKID_TWD>;
>   		};
>
> +		eth1: ethernet at b90000 {
> +			compatible = "marvell,pxa168-eth";
> +			reg = <0xb90000 0x10000>;
> +			clocks = <&chip CLKID_GETH1>;
> +			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> +			/* set by bootloader */
> +			local-mac-address = [00 00 00 00 00 00];
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			phy-connection-type = "mii";
> +			phy-handle = <&ethphy1>;
> +			status = "disabled";
> +
> +			ethphy1: ethernet-phy at 0 {
> +				reg = <0>;
> +			};
> +		};
> +
>   		cpu-ctrl at dd0000 {
>   			compatible = "marvell,berlin-cpu-ctrl";
>   			reg = <0xdd0000 0x10000>;
>   		};
>
> +		eth0: ethernet at e50000 {
> +			compatible = "marvell,pxa168-eth";
> +			reg = <0xe50000 0x10000>;
> +			clocks = <&chip CLKID_GETH0>;
> +			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> +			/* set by bootloader */
> +			local-mac-address = [00 00 00 00 00 00];
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			phy-connection-type = "mii";
> +			phy-handle = <&ethphy0>;
> +			status = "disabled";
> +
> +			ethphy0: ethernet-phy at 0 {
> +				reg = <0>;
> +			};
> +		};
> +
>   		apb at e80000 {
>   			compatible = "simple-bus";
>   			#address-cells = <1>;
>