[PATCH v8 10/13] ARM: dts: berlin: add BG2Q nodes for USB support

[sebastian.hesselbarth@gmail.com (Sebastian Hesselbarth)]

On 17.11.2014 14:35, Antoine Tenart wrote:
> Adds nodes describing the Marvell Berlin BG2Q USB PHY and USB. The BG2Q
> SoC has 3 USB host controller, compatible with ChipIdea.
>
> Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>

Applied to berlin/dt with the whitespace removed that Sergei pointed
out.

Thanks!

> ---
>   arch/arm/boot/dts/berlin2q.dtsi | 55 +++++++++++++++++++++++++++++++++++++++++
>   1 file changed, 55 insertions(+)
>
> diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi
> index 2de8d6f8973c..834142bdfbb1 100644
> --- a/arch/arm/boot/dts/berlin2q.dtsi
> +++ b/arch/arm/boot/dts/berlin2q.dtsi
> @@ -114,6 +114,40 @@
>   			#interrupt-cells = <3>;
>   		};
>
> +		usb_phy2: phy at a2f400 {
> +			compatible = "marvell,berlin2-usb-phy";
> +			reg = <0xa2f400 0x128>;
> +			#phy-cells = <0>;
> +			resets = <&chip 0x104 14>;
> +			status = "disabled";
> +		};
> +
> +		usb2: usb at a30000 {
> +			compatible = "chipidea,usb2";
> +			reg = <0xa30000 0x10000>;
> +			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&chip CLKID_USB2>;
> +			phys = <&usb_phy2>;
> +			phy-names = "usb-phy";
> +			status = "disabled";
> +		};
> +
> +		usb_phy0: phy at b74000 {
> +			compatible = "marvell,berlin2-usb-phy";
> +			reg = <0xb74000 0x128>;
> +			#phy-cells = <0>;
> +			resets = <&chip 0x104 12>;
> +			status = "disabled";
> +		};
> +
> +		usb_phy1: phy at b78000 {
> +			compatible = "marvell,berlin2-usb-phy";
> +			reg = <0xb78000 0x128>;
> +			#phy-cells = <0>;
> +			resets = <&chip 0x104 13>;
> +			status = "disabled";
> +		};
> +
>   		eth0: ethernet at b90000 {
>   			compatible = "marvell,pxa168-eth";
>   			reg = <0xb90000 0x10000>;
> @@ -365,6 +399,26 @@
>   			};
>   		};
>
> +		usb0: usb at ed0000 {
> +			compatible = "chipidea,usb2";
> +			reg = <0xed0000 0x10000>;
> +			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&chip CLKID_USB0>;
> +			phys = <&usb_phy0>;
> +			phy-names = "usb-phy";
> +			status = "disabled";
> +		};
> +
> +		usb1: usb at ee0000 {
> +			compatible = "chipidea,usb2";
> +			reg = <0xee0000 0x10000>;
> +			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&chip CLKID_USB1>;
> +			phys = <&usb_phy1>;
> +			phy-names = "usb-phy";
> +			status = "disabled";
> +		};
> +
>   		apb at fc0000 {
>   			compatible = "simple-bus";
>   			#address-cells = <1>;
> @@ -457,5 +511,6 @@
>   				interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
>   			};
>   		};
> +
>   	};
>   };
>