From: wangyijing <wangyijing@huawei.com>
To: John Garry <john.garry@huawei.com>,
jejb@linux.vnet.ibm.com, martin.petersen@oracle.com
Cc: chenqilin2@huawei.com, hare@suse.com, linux-scsi@vger.kernel.org,
linux-kernel@vger.kernel.org, chenxiang66@hisilicon.com,
huangdaode@hisilicon.com, wangkefeng.wang@huawei.com,
zhaohongjiang@huawei.com, dingtianhong@huawei.com,
guohanjun@huawei.com, yanaijie@huawei.com, hch@lst.de,
dan.j.williams@intel.com, emilne@redhat.com, thenzl@redhat.com,
wefu@redhat.com, charles.chenxin@huawei.com,
chenweilong@huawei.com, Linuxarm <linuxarm@huawei.com>
Subject: Re: [PATCH v3 0/7] Enhance libsas hotplug feature
Date: Thu, 13 Jul 2017 16:38:18 +0800 [thread overview]
Message-ID: <5967317A.9080401@huawei.com> (raw)
In-Reply-To: <47ad4316-e374-26db-3cbe-aa91642aeb68@huawei.com>
在 2017/7/13 16:08, John Garry 写道:
> On 13/07/2017 02:37, wangyijing wrote:
>>> > So much nicer. BTW, /dev/sdb is a SATA disk, the rest are SAS.
>> Oh, I take a mistake ? The result you tested the hotplug which applied this patchset is fine ?
>>
>> Thanks!
>> Yijing.
>
> Well basic hotplug is fine, as below. I did not do any robust testing.
>
OK， thanks，I tested with and without fio running, the results are both fine.
Thanks!
Yijing.
> root@(none)$ echo 0 > ./phy-0:7/sas_phy/phy-0:7/enable
> root@(none)$ [ 180.147676] hisi_sas_v2_hw HISI0162:01: found dev[8:1] is gone
> [ 180.216558] hisi_sas_v2_hw HISI0162:01: found dev[7:1] is gone
> [ 180.280548] hisi_sas_v2_hw HISI0162:01: found dev[6:1] is gone
> [ 180.352556] hisi_sas_v2_hw HISI0162:01: found dev[5:1] is gone
> [ 180.432495] hisi_sas_v2_hw HISI0162:01: found dev[4:1] is gone
> [ 180.508492] hisi_sas_v2_hw HISI0162:01: found dev[3:1] is gone
> [ 180.527577] sd 0:0:1:0: [sdb] Synchronizing SCSI cache
> [ 180.532728] sd 0:0:1:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=0x00
> [ 180.541591] sd 0:0:1:0: [sdb] Stopping disk
> [ 180.545767] sd 0:0:1:0: [sdb] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=0x00
> [ 180.612491] hisi_sas_v2_hw HISI0162:01: found dev[2:5] is gone
> [ 180.696452] hisi_sas_v2_hw HISI0162:01: found dev[1:1] is gone
> [ 180.703221] hisi_sas_v2_hw HISI0162:01: found dev[0:2] is gone
>
> root@(none)$ echo 1 > ./phy-0:7/sas_phy/phy-0:7/enable
> root@(none)$ [ 185.937831] hisi_sas_v2_hw HISI0162:01: phyup: phy7 link_rate=11
> [ 185.996575] scsi 0:0:8:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 187.059642] ata2.00: ATA-8: HGST HUS724040ALA640, MFAOA8B0, max UDMA/133
> [ 187.066341] ata2.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 187.073278] ata2.00: ATA Identify Device Log not supported
> [ 187.078755] ata2.00: Security Log not supported
> [ 187.085239] ata2.00: ATA Identify Device Log not supported
> [ 187.090715] ata2.00: Security Log not supported
> [ 187.095236] ata2.00: configured for UDMA/133
> [ 187.136917] scsi 0:0:9:0: Direct-Access ATA HGST HUS724040AL A8B0 PQ: 0 ANSI: 5
> [ 187.187612] sd 0:0:9:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
> [ 187.195365] sd 0:0:9:0: [sdb] Write Protect is off
> [ 187.200161] sd 0:0:9:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 187.223844] sd 0:0:9:0: [sdb] Attached SCSI disk
> [ 187.225498] scsi 0:0:10:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 187.243864] sd 0:0:8:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 187.285879] sd 0:0:8:0: [sda] Write Protect is off
> [ 187.367898] sd 0:0:8:0: [sda] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 187.524043] scsi 0:0:11:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 187.701505] sd 0:0:10:0: [sdc] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 187.743547] sd 0:0:10:0: [sdc] Write Protect is off
> [ 187.822546] scsi 0:0:12:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 187.825531] sd 0:0:10:0: [sdc] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 188.000167] sd 0:0:11:0: [sdd] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 188.042205] sd 0:0:11:0: [sdd] Write Protect is off
> [ 188.121527] scsi 0:0:13:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 188.124274] sd 0:0:11:0: [sdd] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 188.298942] sd 0:0:12:0: [sde] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 188.340960] sd 0:0:12:0: [sde] Write Protect is off
> [ 188.420023] scsi 0:0:14:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 188.422969] sd 0:0:12:0: [sde] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 188.597501] sd 0:0:13:0: [sdf] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 188.605069] sd 0:0:8:0: [sda] Attached SCSI disk
> [ 188.639520] sd 0:0:13:0: [sdf] Write Protect is off
> [ 188.682445] scsi 0:0:15:0: Enclosure 12G SAS Expander RevB PQ: 0 ANSI: 6
> [ 188.721540] sd 0:0:13:0: [sdf] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 188.896399] sd 0:0:14:0: [sdg] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 188.938445] sd 0:0:14:0: [sdg] Write Protect is off
> [ 189.020444] sd 0:0:14:0: [sdg] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 189.060608] sd 0:0:10:0: [sdc] Attached SCSI disk
> [ 189.359073] sd 0:0:11:0: [sdd] Attached SCSI disk
> [ 189.657643] sd 0:0:12:0: [sde] Attached SCSI disk
> [ 189.956585] sd 0:0:13:0: [sdf] Attached SCSI disk
> [ 190.255148] sd 0:0:14:0: [sdg] Attached SCSI disk
>
> root@(none)$ echo 0 > ./phy-0:7/sas_phy/phy-0:7/enable
> root@(none)$ [ 192.895718] hisi_sas_v2_hw HISI0162:01: found dev[8:1] is gone
> [ 192.964671] hisi_sas_v2_hw HISI0162:01: found dev[7:1] is gone
> [ 193.032744] hisi_sas_v2_hw HISI0162:01: found dev[6:1] is gone
> [ 193.096755] hisi_sas_v2_hw HISI0162:01: found dev[5:1] is gone
> [ 193.157072] hisi_sas_v2_hw HISI0162:01: found dev[4:1] is gone
> [ 193.221062] hisi_sas_v2_hw HISI0162:01: found dev[3:1] is gone
> [ 193.247684] sd 0:0:9:0: [sdb] Synchronizing SCSI cache
> [ 193.252834] sd 0:0:9:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=0x00
> [ 193.261701] sd 0:0:9:0: [sdb] Stopping disk
> [ 193.265879] sd 0:0:9:0: [sdb] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=0x00
> [ 193.325165] hisi_sas_v2_hw HISI0162:01: found dev[2:5] is gone
> [ 193.381094] hisi_sas_v2_hw HISI0162:01: found dev[1:1] is gone
> [ 193.388719] hisi_sas_v2_hw HISI0162:01: found dev[0:2] is gone
>
> root@(none)$ echo 1 > ./phy-0:7/sas_phy/phy-0:7/enable
> root@(none)$ [ 196.221879] hisi_sas_v2_hw HISI0162:01: phyup: phy7 link_rate=11
> [ 196.281178] scsi 0:0:16:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 196.973390] ata3.00: ATA-8: HGST HUS724040ALA640, MFAOA8B0, max UDMA/133
> [ 196.980088] ata3.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 196.987022] ata3.00: ATA Identify Device Log not supported
> [ 196.992499] ata3.00: Security Log not supported
> [ 196.998953] ata3.00: ATA Identify Device Log not supported
> [ 197.004434] ata3.00: Security Log not supported
> [ 197.008954] ata3.00: configured for UDMA/133
> [ 197.050428] scsi 0:0:17:0: Direct-Access ATA HGST HUS724040AL A8B0 PQ: 0 ANSI: 5
> [ 197.091593] sd 0:0:17:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
> [ 197.099441] sd 0:0:17:0: [sdb] Write Protect is off
> [ 197.104326] sd 0:0:17:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 197.122982] sd 0:0:17:0: [sdb] Attached SCSI disk
> [ 197.129367] scsi 0:0:18:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 197.157605] sd 0:0:16:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 197.199622] sd 0:0:16:0: [sda] Write Protect is off
> [ 197.281604] sd 0:0:16:0: [sda] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 197.427727] scsi 0:0:19:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 197.605362] sd 0:0:18:0: [sdc] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 197.647409] sd 0:0:18:0: [sdc] Write Protect is off
> [ 197.726403] scsi 0:0:20:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 197.729389] sd 0:0:18:0: [sdc] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 197.903664] sd 0:0:19:0: [sdd] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 197.945699] sd 0:0:19:0: [sdd] Write Protect is off
> [ 198.024789] scsi 0:0:21:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 198.027685] sd 0:0:19:0: [sdd] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 198.202410] sd 0:0:20:0: [sde] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 198.244458] sd 0:0:20:0: [sde] Write Protect is off
> [ 198.323137] scsi 0:0:22:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 198.326491] sd 0:0:20:0: [sde] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 198.500754] sd 0:0:21:0: [sdf] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 198.516373] sd 0:0:16:0: [sda] Attached SCSI disk
> [ 198.542773] sd 0:0:21:0: [sdf] Write Protect is off
> [ 198.585184] scsi 0:0:23:0: Enclosure 12G SAS Expander RevB PQ: 0 ANSI: 6
> [ 198.624911] sd 0:0:21:0: [sdf] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 198.799446] sd 0:0:22:0: [sdg] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 198.841484] sd 0:0:22:0: [sdg] Write Protect is off
> [ 198.923508] sd 0:0:22:0: [sdg] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 198.964420] sd 0:0:18:0: [sdc] Attached SCSI disk
> [ 199.262903] sd 0:0:19:0: [sdd] Attached SCSI disk
> [ 199.561175] sd 0:0:20:0: [sde] Attached SCSI disk
> [ 199.859533] sd 0:0:21:0: [sdf] Attached SCSI disk
>
> root@(none)$ [ 200.158121] sd 0:0:22:0: [sdg] Attached SCSI disk
>
> root@(none)$
>
>
>>
>>
>>> >
>>> > John
>
>
>
> .
>
WARNING: multiple messages have this Message-ID (diff)
From: wangyijing <wangyijing@huawei.com>
To: John Garry <john.garry@huawei.com>, <jejb@linux.vnet.ibm.com>,
<martin.petersen@oracle.com>
Cc: <chenqilin2@huawei.com>, <hare@suse.com>,
<linux-scsi@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<chenxiang66@hisilicon.com>, <huangdaode@hisilicon.com>,
<wangkefeng.wang@huawei.com>, <zhaohongjiang@huawei.com>,
<dingtianhong@huawei.com>, <guohanjun@huawei.com>,
<yanaijie@huawei.com>, <hch@lst.de>, <dan.j.williams@intel.com>,
<emilne@redhat.com>, <thenzl@redhat.com>, <wefu@redhat.com>,
<charles.chenxin@huawei.com>, <chenweilong@huawei.com>,
Linuxarm <linuxarm@huawei.com>
Subject: Re: [PATCH v3 0/7] Enhance libsas hotplug feature
Date: Thu, 13 Jul 2017 16:38:18 +0800 [thread overview]
Message-ID: <5967317A.9080401@huawei.com> (raw)
In-Reply-To: <47ad4316-e374-26db-3cbe-aa91642aeb68@huawei.com>
在 2017/7/13 16:08, John Garry 写道:
> On 13/07/2017 02:37, wangyijing wrote:
>>> > So much nicer. BTW, /dev/sdb is a SATA disk, the rest are SAS.
>> Oh, I take a mistake ? The result you tested the hotplug which applied this patchset is fine ?
>>
>> Thanks!
>> Yijing.
>
> Well basic hotplug is fine, as below. I did not do any robust testing.
>
OK， thanks，I tested with and without fio running, the results are both fine.
Thanks!
Yijing.
> root@(none)$ echo 0 > ./phy-0:7/sas_phy/phy-0:7/enable
> root@(none)$ [ 180.147676] hisi_sas_v2_hw HISI0162:01: found dev[8:1] is gone
> [ 180.216558] hisi_sas_v2_hw HISI0162:01: found dev[7:1] is gone
> [ 180.280548] hisi_sas_v2_hw HISI0162:01: found dev[6:1] is gone
> [ 180.352556] hisi_sas_v2_hw HISI0162:01: found dev[5:1] is gone
> [ 180.432495] hisi_sas_v2_hw HISI0162:01: found dev[4:1] is gone
> [ 180.508492] hisi_sas_v2_hw HISI0162:01: found dev[3:1] is gone
> [ 180.527577] sd 0:0:1:0: [sdb] Synchronizing SCSI cache
> [ 180.532728] sd 0:0:1:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=0x00
> [ 180.541591] sd 0:0:1:0: [sdb] Stopping disk
> [ 180.545767] sd 0:0:1:0: [sdb] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=0x00
> [ 180.612491] hisi_sas_v2_hw HISI0162:01: found dev[2:5] is gone
> [ 180.696452] hisi_sas_v2_hw HISI0162:01: found dev[1:1] is gone
> [ 180.703221] hisi_sas_v2_hw HISI0162:01: found dev[0:2] is gone
>
> root@(none)$ echo 1 > ./phy-0:7/sas_phy/phy-0:7/enable
> root@(none)$ [ 185.937831] hisi_sas_v2_hw HISI0162:01: phyup: phy7 link_rate=11
> [ 185.996575] scsi 0:0:8:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 187.059642] ata2.00: ATA-8: HGST HUS724040ALA640, MFAOA8B0, max UDMA/133
> [ 187.066341] ata2.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 187.073278] ata2.00: ATA Identify Device Log not supported
> [ 187.078755] ata2.00: Security Log not supported
> [ 187.085239] ata2.00: ATA Identify Device Log not supported
> [ 187.090715] ata2.00: Security Log not supported
> [ 187.095236] ata2.00: configured for UDMA/133
> [ 187.136917] scsi 0:0:9:0: Direct-Access ATA HGST HUS724040AL A8B0 PQ: 0 ANSI: 5
> [ 187.187612] sd 0:0:9:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
> [ 187.195365] sd 0:0:9:0: [sdb] Write Protect is off
> [ 187.200161] sd 0:0:9:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 187.223844] sd 0:0:9:0: [sdb] Attached SCSI disk
> [ 187.225498] scsi 0:0:10:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 187.243864] sd 0:0:8:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 187.285879] sd 0:0:8:0: [sda] Write Protect is off
> [ 187.367898] sd 0:0:8:0: [sda] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 187.524043] scsi 0:0:11:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 187.701505] sd 0:0:10:0: [sdc] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 187.743547] sd 0:0:10:0: [sdc] Write Protect is off
> [ 187.822546] scsi 0:0:12:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 187.825531] sd 0:0:10:0: [sdc] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 188.000167] sd 0:0:11:0: [sdd] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 188.042205] sd 0:0:11:0: [sdd] Write Protect is off
> [ 188.121527] scsi 0:0:13:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 188.124274] sd 0:0:11:0: [sdd] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 188.298942] sd 0:0:12:0: [sde] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 188.340960] sd 0:0:12:0: [sde] Write Protect is off
> [ 188.420023] scsi 0:0:14:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 188.422969] sd 0:0:12:0: [sde] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 188.597501] sd 0:0:13:0: [sdf] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 188.605069] sd 0:0:8:0: [sda] Attached SCSI disk
> [ 188.639520] sd 0:0:13:0: [sdf] Write Protect is off
> [ 188.682445] scsi 0:0:15:0: Enclosure 12G SAS Expander RevB PQ: 0 ANSI: 6
> [ 188.721540] sd 0:0:13:0: [sdf] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 188.896399] sd 0:0:14:0: [sdg] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 188.938445] sd 0:0:14:0: [sdg] Write Protect is off
> [ 189.020444] sd 0:0:14:0: [sdg] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 189.060608] sd 0:0:10:0: [sdc] Attached SCSI disk
> [ 189.359073] sd 0:0:11:0: [sdd] Attached SCSI disk
> [ 189.657643] sd 0:0:12:0: [sde] Attached SCSI disk
> [ 189.956585] sd 0:0:13:0: [sdf] Attached SCSI disk
> [ 190.255148] sd 0:0:14:0: [sdg] Attached SCSI disk
>
> root@(none)$ echo 0 > ./phy-0:7/sas_phy/phy-0:7/enable
> root@(none)$ [ 192.895718] hisi_sas_v2_hw HISI0162:01: found dev[8:1] is gone
> [ 192.964671] hisi_sas_v2_hw HISI0162:01: found dev[7:1] is gone
> [ 193.032744] hisi_sas_v2_hw HISI0162:01: found dev[6:1] is gone
> [ 193.096755] hisi_sas_v2_hw HISI0162:01: found dev[5:1] is gone
> [ 193.157072] hisi_sas_v2_hw HISI0162:01: found dev[4:1] is gone
> [ 193.221062] hisi_sas_v2_hw HISI0162:01: found dev[3:1] is gone
> [ 193.247684] sd 0:0:9:0: [sdb] Synchronizing SCSI cache
> [ 193.252834] sd 0:0:9:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=0x00
> [ 193.261701] sd 0:0:9:0: [sdb] Stopping disk
> [ 193.265879] sd 0:0:9:0: [sdb] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=0x00
> [ 193.325165] hisi_sas_v2_hw HISI0162:01: found dev[2:5] is gone
> [ 193.381094] hisi_sas_v2_hw HISI0162:01: found dev[1:1] is gone
> [ 193.388719] hisi_sas_v2_hw HISI0162:01: found dev[0:2] is gone
>
> root@(none)$ echo 1 > ./phy-0:7/sas_phy/phy-0:7/enable
> root@(none)$ [ 196.221879] hisi_sas_v2_hw HISI0162:01: phyup: phy7 link_rate=11
> [ 196.281178] scsi 0:0:16:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 196.973390] ata3.00: ATA-8: HGST HUS724040ALA640, MFAOA8B0, max UDMA/133
> [ 196.980088] ata3.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 196.987022] ata3.00: ATA Identify Device Log not supported
> [ 196.992499] ata3.00: Security Log not supported
> [ 196.998953] ata3.00: ATA Identify Device Log not supported
> [ 197.004434] ata3.00: Security Log not supported
> [ 197.008954] ata3.00: configured for UDMA/133
> [ 197.050428] scsi 0:0:17:0: Direct-Access ATA HGST HUS724040AL A8B0 PQ: 0 ANSI: 5
> [ 197.091593] sd 0:0:17:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
> [ 197.099441] sd 0:0:17:0: [sdb] Write Protect is off
> [ 197.104326] sd 0:0:17:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 197.122982] sd 0:0:17:0: [sdb] Attached SCSI disk
> [ 197.129367] scsi 0:0:18:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 197.157605] sd 0:0:16:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 197.199622] sd 0:0:16:0: [sda] Write Protect is off
> [ 197.281604] sd 0:0:16:0: [sda] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 197.427727] scsi 0:0:19:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 197.605362] sd 0:0:18:0: [sdc] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 197.647409] sd 0:0:18:0: [sdc] Write Protect is off
> [ 197.726403] scsi 0:0:20:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 197.729389] sd 0:0:18:0: [sdc] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 197.903664] sd 0:0:19:0: [sdd] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 197.945699] sd 0:0:19:0: [sdd] Write Protect is off
> [ 198.024789] scsi 0:0:21:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 198.027685] sd 0:0:19:0: [sdd] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 198.202410] sd 0:0:20:0: [sde] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 198.244458] sd 0:0:20:0: [sde] Write Protect is off
> [ 198.323137] scsi 0:0:22:0: Direct-Access SanDisk LT0200MO P404 PQ: 0 ANSI: 6
> [ 198.326491] sd 0:0:20:0: [sde] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 198.500754] sd 0:0:21:0: [sdf] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 198.516373] sd 0:0:16:0: [sda] Attached SCSI disk
> [ 198.542773] sd 0:0:21:0: [sdf] Write Protect is off
> [ 198.585184] scsi 0:0:23:0: Enclosure 12G SAS Expander RevB PQ: 0 ANSI: 6
> [ 198.624911] sd 0:0:21:0: [sdf] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 198.799446] sd 0:0:22:0: [sdg] 390721968 512-byte logical blocks: (200 GB/186 GiB)
> [ 198.841484] sd 0:0:22:0: [sdg] Write Protect is off
> [ 198.923508] sd 0:0:22:0: [sdg] Write cache: disabled, read cache: disabled, supports DPO and FUA
> [ 198.964420] sd 0:0:18:0: [sdc] Attached SCSI disk
> [ 199.262903] sd 0:0:19:0: [sdd] Attached SCSI disk
> [ 199.561175] sd 0:0:20:0: [sde] Attached SCSI disk
> [ 199.859533] sd 0:0:21:0: [sdf] Attached SCSI disk
>
> root@(none)$ [ 200.158121] sd 0:0:22:0: [sdg] Attached SCSI disk
>
> root@(none)$
>
>
>>
>>
>>> >
>>> > John
>
>
>
> .
>
next prev parent reply other threads:[~2017-07-13 8:38 UTC|newest]
Thread overview: 70+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-07-10 7:06 [PATCH v3 0/7] Enhance libsas hotplug feature Yijing Wang
2017-07-10 7:06 ` Yijing Wang
2017-07-10 7:06 ` [PATCH v3 1/7] libsas: Use static sas event pool to appease sas event lost Yijing Wang
2017-07-10 7:06 ` Yijing Wang
2017-07-11 15:37 ` John Garry
2017-07-11 15:37 ` John Garry
2017-07-12 2:06 ` wangyijing
2017-07-12 2:06 ` wangyijing
2017-07-12 8:17 ` John Garry
2017-07-12 8:17 ` John Garry
2017-07-12 8:47 ` wangyijing
2017-07-12 8:47 ` wangyijing
2017-07-12 10:13 ` John Garry
2017-07-12 10:13 ` John Garry
2017-07-13 2:13 ` wangyijing
2017-07-13 2:13 ` wangyijing
2017-07-14 6:40 ` Hannes Reinecke
2017-07-10 7:06 ` [PATCH v3 2/7] libsas: remove unused port_gone_completion Yijing Wang
2017-07-10 7:06 ` Yijing Wang
2017-07-11 15:54 ` John Garry
2017-07-11 15:54 ` John Garry
2017-07-12 2:18 ` wangyijing
2017-07-12 2:18 ` wangyijing
2017-07-14 6:40 ` Hannes Reinecke
2017-07-10 7:06 ` [PATCH v3 3/7] libsas: Use new workqueue to run sas event Yijing Wang
2017-07-10 7:06 ` Yijing Wang
2017-07-14 6:42 ` Hannes Reinecke
2017-07-10 7:06 ` [PATCH v3 4/7] libsas: add sas event wait-complete support Yijing Wang
2017-07-10 7:06 ` Yijing Wang
2017-07-14 6:51 ` Hannes Reinecke
2017-07-14 7:46 ` wangyijing
2017-07-14 7:46 ` wangyijing
2017-07-14 8:42 ` John Garry
2017-07-14 8:42 ` John Garry
2017-07-10 7:06 ` [PATCH v3 5/7] libsas: add a new workqueue to run probe/destruct discovery event Yijing Wang
2017-07-10 7:06 ` Yijing Wang
2017-07-12 16:50 ` John Garry
2017-07-12 16:50 ` John Garry
2017-07-13 2:36 ` wangyijing
2017-07-13 2:36 ` wangyijing
2017-07-14 6:52 ` Hannes Reinecke
2017-07-10 7:06 ` [PATCH v3 6/7] libsas: add wait-complete support to sync " Yijing Wang
2017-07-10 7:06 ` Yijing Wang
2017-07-12 13:51 ` John Garry
2017-07-12 13:51 ` John Garry
2017-07-13 2:19 ` wangyijing
2017-07-13 2:19 ` wangyijing
2017-07-14 6:53 ` Hannes Reinecke
2017-07-10 7:06 ` [PATCH v3 7/7] libsas: release disco mutex during waiting in sas_ex_discover_end_dev Yijing Wang
2017-07-10 7:06 ` Yijing Wang
2017-07-13 16:10 ` John Garry
2017-07-13 16:10 ` John Garry
2017-07-14 1:44 ` wangyijing
2017-07-14 1:44 ` wangyijing
2017-07-14 8:26 ` John Garry
2017-07-14 8:26 ` John Garry
2017-07-14 6:55 ` Hannes Reinecke
2017-07-12 9:59 ` [PATCH v3 0/7] Enhance libsas hotplug feature John Garry
2017-07-12 9:59 ` John Garry
2017-07-12 11:56 ` Johannes Thumshirn
2017-07-13 1:27 ` wangyijing
2017-07-13 1:27 ` wangyijing
2017-07-13 1:37 ` wangyijing
2017-07-13 1:37 ` wangyijing
2017-07-13 8:08 ` John Garry
2017-07-13 8:08 ` John Garry
2017-07-13 8:38 ` wangyijing [this message]
2017-07-13 8:38 ` wangyijing
2017-07-14 8:19 ` wangyijing
2017-07-14 8:19 ` wangyijing
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5967317A.9080401@huawei.com \
--to=wangyijing@huawei.com \
--cc=charles.chenxin@huawei.com \
--cc=chenqilin2@huawei.com \
--cc=chenweilong@huawei.com \
--cc=chenxiang66@hisilicon.com \
--cc=dan.j.williams@intel.com \
--cc=dingtianhong@huawei.com \
--cc=emilne@redhat.com \
--cc=guohanjun@huawei.com \
--cc=hare@suse.com \
--cc=hch@lst.de \
--cc=huangdaode@hisilicon.com \
--cc=jejb@linux.vnet.ibm.com \
--cc=john.garry@huawei.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=linuxarm@huawei.com \
--cc=martin.petersen@oracle.com \
--cc=thenzl@redhat.com \
--cc=wangkefeng.wang@huawei.com \
--cc=wefu@redhat.com \
--cc=yanaijie@huawei.com \
--cc=zhaohongjiang@huawei.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.