Re: [PATCH 6/9] arm64: dts: meson: g12a: Add UART A, B & C nodes and pins

[Neil Armstrong <narmstrong@baylibre.com>]

Le 15/03/2019 22:24, Martin Blumenstingl a écrit :
> Hi Neil,
> 
> On Thu, Mar 7, 2019 at 4:15 PM Neil Armstrong <narmstrong@baylibre.com> wrote:
>>
>> This patch adds the 2 UART nodes in the EE power domain with the corresponding
>> pinctrl nodes.
> there are 3 UART controllers in the EE power domain

Good catch !

> 
>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>> ---
>>  arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 82 +++++++++++++++++++++
>>  1 file changed, 82 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
>> index 2a700bb45d04..50e2cd36e08b 100644
>> --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
>> +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
>> @@ -113,6 +113,61 @@
>>                                                 #gpio-cells = <2>;
>>                                                 gpio-ranges = <&periphs_pinctrl 0 0 86>;
>>                                         };
>> +
>> +                                       uart_a_pins: uart_a {
> (this applies to all new nodes)
> we started using dashes for the node names for new pin definitions on
> the GX SoCs.
> I don't remember where it was discussed exactly but I think this was
> requested from Rob

Yes I remember, will fix

> 
> since G12A is a new SoC we should do it "right" from the beginning
> 
> [...]
>> +                                       uart_ao_a_c_pins: uart_ao_a_c {
>> +                                               mux {
>> +                                                       groups = "uart_ao_a_rx_c",
>> +                                                                "uart_ao_a_tx_c";
>> +                                                       function = "uart_ao_a_c";
>> +                                                       bias-disable;
>> +                                               };
>> +                                       };
> I'm fine with this part if you mention it in the subject and/or the description
> uart_ao_a_c routes two pins from bank C (from the EE domain) to the
> uart_AO controller (from the AO domain)

Not sure DT is the right place for that, I think I'll remove this until
we have it actually used somewhere.

> 
>> +                                       uart_b_pins: uart_b {
>> +                                               mux {
>> +                                                       groups = "uart_b_tx",
>> +                                                                "uart_b_rx";
>> +                                                       function = "uart_b";
>> +                                                       bias-disable;
>> +                                               };
>> +                                       };
>> +
>> +                                       uart_c_pins: uart_c {
>> +                                               mux {
>> +                                                       groups = "uart_c_tx",
>> +                                                                "uart_c_rx";
>> +                                                       function = "uart_c";
>> +                                                       bias-disable;
>> +                                               };
>> +                                       };
>> +
>> +                                       uart_c_cts_rts_pins: uart_c_cts_rts {
>> +                                               mux {
>> +                                                       groups = "uart_c_cts",
>> +                                                                "uart_c_rts";
>> +                                                       function = "uart_c";
>> +                                                       bias-disable;
>> +                                               };
>> +                                       };
>> +                               };
>>                         };
>>
>>                         hiu: bus@3c000 {
>> @@ -256,6 +311,33 @@
>>                                 compatible = "amlogic,meson-g12a-clk-measure";
>>                                 reg = <0x0 0x18000 0x0 0x10>;
>>                         };
>> +
>> +                       uart_C: serial@22000 {
>> +                               compatible = "amlogic,meson-gx-uart";
>> +                               reg = <0x0 0x22000 0x0 0x18>;
>> +                               interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
>> +                               clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
> does uart_C really use CLKID_UART1? on GX uart_C uses CLKID_UART2

It seems so :
https://github.com/hardkernel/linux/blob/odroidn2-4.9.y/arch/arm64/boot/dts/amlogic/mesong12a.dtsi#L1020

Neil

> 
> 
> Regards
> Martin
> 

_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic