* [PATCH v2 0/4] riscv: spacemit: Add support for K3 Pico-ITX board
@ 2026-10-02 1:03 Yixun Lan
2026-10-02 1:03 ` [PATCH v2 1/4] board: spacemit: add SpacemiT K3 Pico-ITX Yixun Lan
` (3 more replies)
0 siblings, 4 replies; 8+ messages in thread
From: Yixun Lan @ 2026-10-02 1:03 UTC (permalink / raw)
To: u-boot
Cc: Yao Zi, Tim Ouyang, Leo Liang, Tom Rini, Michal Simek,
Raymond Mao, Hiago De Franco, Junhui Liu, Yixun Lan
Add initial support for SpacemiT K3 Pico-ITX board, the config file
will enable all basic components which make it able to run into U-Boot
serial console.
The series actually depend on previous sent patches, I'm not adding
dependency to this series, but list it here for reference.
Pinctrl:
https://patch.msgid.link/20260923-01-k3-pinctrl-support-v2-0-e76a917ee252@kernel.org
GPIO:
https://patch.msgid.link/20260822-01-gpio-pinctrl-support-v1-1-6be2f4c71c5d@kernel.org
clock and reset:
https://patch.msgid.link/20260923-01-k3-clock-reset-support-v2-0-6ec0abb1c7b5@kernel.org
Signed-off-by: Yixun Lan <dlan@kernel.org>
---
Changes in v2:
- drop board_get_usable_ram_top()
- drop empty source file
- Link to v1: https://patch.msgid.link/20260923-00-basic-spacemit-k3-v1-0-fa1015f2cd1b@kernel.org
---
Yixun Lan (4):
board: spacemit: add SpacemiT K3 Pico-ITX
riscv: dts: spacemit: k3: add binman node
configs: spacemit: Add K3 default configuration
doc: spacemit: k3: Add Pico-ITX board
arch/riscv/Kconfig | 5 +
arch/riscv/cpu/k3/Kconfig | 18 +++
arch/riscv/cpu/k3/Makefile | 5 +
arch/riscv/cpu/k3/dram.c | 21 ++++
arch/riscv/dts/k3-u-boot.dtsi | 6 +
board/spacemit/k3/Kconfig | 30 +++++
board/spacemit/k3/MAINTAINERS | 8 ++
configs/spacemit_k3_defconfig | 50 ++++++++
doc/board/spacemit/index.rst | 1 +
doc/board/spacemit/spacemit-pico-itx.rst | 204 +++++++++++++++++++++++++++++++
include/configs/k3.h | 13 ++
11 files changed, 361 insertions(+)
---
base-commit: cf615aafae36fc49f55e3e6a3648d29201b26d51
change-id: 20260921-00-basic-spacemit-k3-838119645d39
Best regards,
--
Yixun Lan <dlan@kernel.org>
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2 1/4] board: spacemit: add SpacemiT K3 Pico-ITX
2026-10-02 1:03 [PATCH v2 0/4] riscv: spacemit: Add support for K3 Pico-ITX board Yixun Lan
@ 2026-10-02 1:03 ` Yixun Lan
2026-10-02 7:02 ` E Shattow
2026-10-02 1:03 ` [PATCH v2 2/4] riscv: dts: spacemit: k3: add binman node Yixun Lan
` (2 subsequent siblings)
3 siblings, 1 reply; 8+ messages in thread
From: Yixun Lan @ 2026-10-02 1:03 UTC (permalink / raw)
To: u-boot
Cc: Yao Zi, Tim Ouyang, Leo Liang, Tom Rini, Michal Simek,
Raymond Mao, Hiago De Franco, Junhui Liu, Yixun Lan
Add initial support for K3 Pico-ITX board, in this version, the DRAM
information is parsed from DTS "/memory" node. And with UART enabled,
the U-Boot serial console works fine now.
Signed-off-by: Yixun Lan <dlan@kernel.org>
---
arch/riscv/Kconfig | 5 +++++
arch/riscv/cpu/k3/Kconfig | 18 ++++++++++++++++++
arch/riscv/cpu/k3/Makefile | 5 +++++
arch/riscv/cpu/k3/dram.c | 21 +++++++++++++++++++++
board/spacemit/k3/Kconfig | 30 ++++++++++++++++++++++++++++++
board/spacemit/k3/MAINTAINERS | 8 ++++++++
include/configs/k3.h | 13 +++++++++++++
7 files changed, 100 insertions(+)
diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
index c1b2890f1f3..386241efd4a 100644
--- a/arch/riscv/Kconfig
+++ b/arch/riscv/Kconfig
@@ -53,6 +53,9 @@ config TARGET_SIPEED_MAIX
config TARGET_SPACEMIT_K1
bool "Support Spacemit K1 SoC"
+config TARGET_SPACEMIT_K3
+ bool "Support SpacemiT K3 SoC"
+
config TARGET_STARFIVE_VISIONFIVE2
bool "Support StarFive VisionFive2 Board"
select BOARD_LATE_INIT
@@ -124,6 +127,7 @@ source "board/sophgo/milkv_duo/Kconfig"
source "board/sophgo/milkv_duo_256m/Kconfig"
source "board/sophgo/licheerv_nano/Kconfig"
source "board/spacemit/k1/Kconfig"
+source "board/spacemit/k3/Kconfig"
source "board/starfive/visionfive2/Kconfig"
source "board/thead/th1520_lpi4a/Kconfig"
source "board/xilinx/mbv/Kconfig"
@@ -138,6 +142,7 @@ source "arch/riscv/cpu/mpfs/Kconfig"
source "arch/riscv/cpu/generic/Kconfig"
source "arch/riscv/cpu/jh7110/Kconfig"
source "arch/riscv/cpu/k1/Kconfig"
+source "arch/riscv/cpu/k3/Kconfig"
source "arch/riscv/cpu/k230/Kconfig"
source "arch/riscv/cpu/th1520/Kconfig"
diff --git a/arch/riscv/cpu/k3/Kconfig b/arch/riscv/cpu/k3/Kconfig
new file mode 100644
index 00000000000..5474ac11243
--- /dev/null
+++ b/arch/riscv/cpu/k3/Kconfig
@@ -0,0 +1,18 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
+
+if TARGET_SPACEMIT_K3
+
+config SPACEMIT_K3
+ bool
+ select BINMAN
+ select ARCH_EARLY_INIT_R
+ select SYS_CACHE_SHIFT_6
+ imply CPU
+ imply CPU_RISCV
+ imply RISCV_TIMER if RISCV_SMODE
+ imply CMD_CPU
+ imply OF_UPSTREAM
+
+endif
diff --git a/arch/riscv/cpu/k3/Makefile b/arch/riscv/cpu/k3/Makefile
new file mode 100644
index 00000000000..fba4e4b0a3f
--- /dev/null
+++ b/arch/riscv/cpu/k3/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
+
+obj-y += dram.o
diff --git a/arch/riscv/cpu/k3/dram.c b/arch/riscv/cpu/k3/dram.c
new file mode 100644
index 00000000000..e20d35dc1bf
--- /dev/null
+++ b/arch/riscv/cpu/k3/dram.c
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
+ */
+
+#include <fdtdec.h>
+#include <init.h>
+#include <linux/sizes.h>
+#include <asm/global_data.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+ return fdtdec_setup_mem_size_base();
+}
+
+int dram_init_banksize(void)
+{
+ return fdtdec_setup_memory_banksize();
+}
diff --git a/board/spacemit/k3/Kconfig b/board/spacemit/k3/Kconfig
new file mode 100644
index 00000000000..b0e423d829c
--- /dev/null
+++ b/board/spacemit/k3/Kconfig
@@ -0,0 +1,30 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
+
+if TARGET_SPACEMIT_K3
+
+config SYS_BOARD
+ default "k3"
+
+config SYS_VENDOR
+ default "spacemit"
+
+config SYS_CPU
+ default "k3"
+
+config SYS_CONFIG_NAME
+ default "k3"
+
+config TEXT_BASE
+ default 0x102000000
+
+config SPL_OPENSBI_LOAD_ADDR
+ hex
+ default 0x100000000
+
+config BOARD_SPECIFIC_OPTIONS
+ def_bool y
+ select SPACEMIT_K3
+
+endif
diff --git a/board/spacemit/k3/MAINTAINERS b/board/spacemit/k3/MAINTAINERS
new file mode 100644
index 00000000000..34cf1ed4453
--- /dev/null
+++ b/board/spacemit/k3/MAINTAINERS
@@ -0,0 +1,8 @@
+SPACEMIT K3
+M: Yixun Lan <dlan@kernel.org>
+S: Maintained
+F: arch/riscv/cpu/k3/
+F: board/spacemit/k3/
+F: configs/spacemit_k3_defconfig
+F: include/configs/k3.h
+F: arch/riscv/dts/k3-u-boot.dtsi
diff --git a/include/configs/k3.h b/include/configs/k3.h
new file mode 100644
index 00000000000..83e4945d2b3
--- /dev/null
+++ b/include/configs/k3.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CFG_SYS_NS16550_IER 0x40
+
+#define RISCV_SMODE_TIMER_FREQ 24000000
+
+#endif /* __CONFIG_H */
--
2.56.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 2/4] riscv: dts: spacemit: k3: add binman node
2026-10-02 1:03 [PATCH v2 0/4] riscv: spacemit: Add support for K3 Pico-ITX board Yixun Lan
2026-10-02 1:03 ` [PATCH v2 1/4] board: spacemit: add SpacemiT K3 Pico-ITX Yixun Lan
@ 2026-10-02 1:03 ` Yixun Lan
2026-10-02 3:20 ` E Shattow
2026-10-02 1:03 ` [PATCH v2 3/4] configs: spacemit: Add K3 default configuration Yixun Lan
2026-10-02 1:03 ` [PATCH v2 4/4] doc: spacemit: k3: Add Pico-ITX board Yixun Lan
3 siblings, 1 reply; 8+ messages in thread
From: Yixun Lan @ 2026-10-02 1:03 UTC (permalink / raw)
To: u-boot
Cc: Yao Zi, Tim Ouyang, Leo Liang, Tom Rini, Michal Simek,
Raymond Mao, Hiago De Franco, Junhui Liu, Yixun Lan
SpacemiT K3 follow the standard riscv binman layout, which has opensbi
and U-Boot proper, so include the common binman dtsi file.
Signed-off-by: Yixun Lan <dlan@kernel.org>
---
arch/riscv/dts/k3-u-boot.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/riscv/dts/k3-u-boot.dtsi b/arch/riscv/dts/k3-u-boot.dtsi
new file mode 100644
index 00000000000..f1c1c3ee6fd
--- /dev/null
+++ b/arch/riscv/dts/k3-u-boot.dtsi
@@ -0,0 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
+ */
+
+#include "binman.dtsi"
--
2.56.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 3/4] configs: spacemit: Add K3 default configuration
2026-10-02 1:03 [PATCH v2 0/4] riscv: spacemit: Add support for K3 Pico-ITX board Yixun Lan
2026-10-02 1:03 ` [PATCH v2 1/4] board: spacemit: add SpacemiT K3 Pico-ITX Yixun Lan
2026-10-02 1:03 ` [PATCH v2 2/4] riscv: dts: spacemit: k3: add binman node Yixun Lan
@ 2026-10-02 1:03 ` Yixun Lan
2026-10-02 1:03 ` [PATCH v2 4/4] doc: spacemit: k3: Add Pico-ITX board Yixun Lan
3 siblings, 0 replies; 8+ messages in thread
From: Yixun Lan @ 2026-10-02 1:03 UTC (permalink / raw)
To: u-boot
Cc: Yao Zi, Tim Ouyang, Leo Liang, Tom Rini, Michal Simek,
Raymond Mao, Hiago De Franco, Junhui Liu, Yixun Lan
Add the default configuration for SpacemiT K3 boards, using the
Pico-ITX device tree as the default.
Configure U-Boot to run in RISC-V supervisor mode and enable the
platform clock, reset, GPIO, pinctrl, I2C, PMIC and regulator drivers.
Also configure the memory layout, debug UART and basic filesystem
commands required to boot on the platform.
Signed-off-by: Yixun Lan <dlan@kernel.org>
---
configs/spacemit_k3_defconfig | 50 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 50 insertions(+)
diff --git a/configs/spacemit_k3_defconfig b/configs/spacemit_k3_defconfig
new file mode 100644
index 00000000000..6ca41aecc41
--- /dev/null
+++ b/configs/spacemit_k3_defconfig
@@ -0,0 +1,50 @@
+CONFIG_RISCV=y
+CONFIG_SYS_MALLOC_LEN=0x1000000
+CONFIG_SYS_MALLOC_F_LEN=0x80000
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x102300000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="spacemit/k3-pico-itx"
+CONFIG_SYS_BOOTM_LEN=0xa000000
+CONFIG_SYS_LOAD_ADDR=0x102000000
+CONFIG_DEBUG_UART_BASE=0xd4017000
+CONFIG_DEBUG_UART_CLOCK=14700000
+CONFIG_TARGET_SPACEMIT_K3=y
+CONFIG_ARCH_RV64I=y
+CONFIG_CMODEL_MEDANY=y
+CONFIG_RISCV_SMODE=y
+CONFIG_RISCV_ISA_ZICBOM=y
+CONFIG_STACK_SIZE=0x100000
+CONFIG_FIT=y
+CONFIG_SUPPORT_RAW_INITRD=y
+CONFIG_SYS_CBSIZE=256
+CONFIG_SYS_PBSIZE=276
+# CONFIG_BOARD_INIT is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_SYSCON=y
+CONFIG_CLK_SPACEMIT=y
+CONFIG_CLK_SPACEMIT_K3=y
+CONFIG_SPACEMIT_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_SPACEMIT_K1=y
+CONFIG_MISC=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_SPACEMIT_K1=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_SPACEMIT_P1=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_SPACEMIT_P1=y
+CONFIG_DEBUG_UART_NS16550=y
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_SYS_NS16550=y
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_TIMER_EARLY=y
--
2.56.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 4/4] doc: spacemit: k3: Add Pico-ITX board
2026-10-02 1:03 [PATCH v2 0/4] riscv: spacemit: Add support for K3 Pico-ITX board Yixun Lan
` (2 preceding siblings ...)
2026-10-02 1:03 ` [PATCH v2 3/4] configs: spacemit: Add K3 default configuration Yixun Lan
@ 2026-10-02 1:03 ` Yixun Lan
3 siblings, 0 replies; 8+ messages in thread
From: Yixun Lan @ 2026-10-02 1:03 UTC (permalink / raw)
To: u-boot
Cc: Yao Zi, Tim Ouyang, Leo Liang, Tom Rini, Michal Simek,
Raymond Mao, Hiago De Franco, Junhui Liu, Yixun Lan
Add documentation for how to test the mainline U-Boot on SpacemiT
K3 Pico-ITX board, currently it still rely on using vendor FSBL.bin
file to initialize DDR and boot U-Boot proper, and the opensbi
firmware is built from an on-going mainline branch.
Signed-off-by: Yixun Lan <dlan@kernel.org>
---
doc/board/spacemit/index.rst | 1 +
doc/board/spacemit/spacemit-pico-itx.rst | 204 +++++++++++++++++++++++++++++++
2 files changed, 205 insertions(+)
diff --git a/doc/board/spacemit/index.rst b/doc/board/spacemit/index.rst
index 71854e5735b..51918f0acc7 100644
--- a/doc/board/spacemit/index.rst
+++ b/doc/board/spacemit/index.rst
@@ -8,4 +8,5 @@ SpacemiT
bananapi-f3
k1-mmc
k1-spl
+ spacemit-pico-itx
diff --git a/doc/board/spacemit/spacemit-pico-itx.rst b/doc/board/spacemit/spacemit-pico-itx.rst
new file mode 100644
index 00000000000..dd29e3c31c8
--- /dev/null
+++ b/doc/board/spacemit/spacemit-pico-itx.rst
@@ -0,0 +1,204 @@
+.. SPDX-License-Identifier: GPL-2.0-or-later
+
+SpacemiT K3 Pico-ITX
+====================
+
+Building
+~~~~~~~~
+1. Install the SpacemiT riscv cross compile toolchain_, or skip it if riscv toolchain is installed.
+
+.. _toolchain: https://archive.spacemit.com/toolchain/
+
+2. Setup cross compilation environment variable:
+
+.. code-block:: console
+
+ export CROSS_COMPILE=<riscv64 toolchain prefix, e.g /opt/spacemit/bin/riscv64-unknown-linux-gnu->
+
+3. Before building U-Boot, OpenSBI should be built first. OpenSBI can be
+built for SpacemiT K1 SoC as below:
+
+.. code-block:: console
+
+ git clone https://github.com/spacemit-com/opensbi-upstream opensbi
+ cd opensbi
+ make PLATFORM=generic
+
+4. Then build U-Boot as following:
+
+.. code-block:: console
+
+ cd <U-Boot-dir>
+ make spacemit_k3_defconfig
+ make OPENSBI=<OpenSBI-dir>/build/platform/generic/firmware/fw_dynamic.bin
+
+This will generate u-boot.itb
+
+Testing
+~~~~~~~
+Currently, in this stage, the U-Boot SPL isn't ready, and has no ddr initialization code
+Thus please test with fasboot command via USB download.
+
+First, retrieve Bianbu Linux image from archive_ and extract the FSBL.bin firmware.
+
+Second, hold the FEL button of Pico-ITX board, then press reset button and release it .
+The board will enter into firmware download mode.
+
+.. code-block:: none
+
+ sys: 0x10001200
+ bm:2
+ usb_init : enter 3296,3072
+ usb_core_init : enter
+ DWC3_GRXTHRCFG:0x4400000
+ ROM: usb download handler
+ rst
+ done H
+ setup= 0x1000680 0x400000,
+ rst
+ done H
+ setup= 0x290500 0x0,
+ setup= 0x1000680 0x120000,
+ setup= 0x2000680 0x90000,
+ setup= 0x2000680 0x200000,
+ setup= 0x3000680 0xff0000,
+ setup= 0x3020680 0xff0409,
+ setup= 0x3010680 0xff0409,
+ setup= 0x10900 0x0,
+ usb_rx_bytes : start len[4096]
+ setup= 0x3020680 0xff0409,
+ setup= 0x3040680 0xff0409,
+
+Run following command to test:
+
+.. code-block:: console
+
+ fastboot stage FSBL.bin
+ fastboot continue
+ sleep 10
+ fastboot stage u-boot.itb
+ fastboot continue
+
+.. _archive: https://archive.spacemit.com/image/k3/version/bianbu/v4.0.7/
+.. _uboot: https://bianbu-linux.spacemit.com/en/device/boot#21-firmware-layout
+
+Booting
+~~~~~~~
+Sample boot log
+~~~~~~~~~~~~~~~
+.. code-block:: none
+
+ sys: 0x10001200
+ bm:2
+ usb_init : enter 3296,3072
+ usb_core_init : enter
+ DWC3_GRXTHRCFG:0x4400000
+ ROM: usb download handler
+ rst
+ done H
+ setup= 0x1000680 0x400000,
+ rst
+ done H
+ setup= 0x2f0500 0x0,
+ setup= 0x1000680 0x120000,
+ setup= 0x2000680 0x90000,
+ setup= 0x2000680 0x200000,
+ setup= 0x3000680 0xff0000,
+ setup= 0x3020680 0xff0409,
+ setup= 0x3010680 0xff0409,
+ setup= 0x10900 0x0,
+ usb_rx_bytes : start len[4096]
+ setup= 0x3020680 0xff0409,
+ setup= 0x3040680 0xff0409,
+ fastboot_handle_command: max-download-size
+ usb_tx_bytes : start len[14]
+ usb_rx_bytes : start len[4096]
+ fastboot_handle_command: 00072b20
+ Starting download of 469792 bytes
+ usb_tx_bytes : start len[12]
+ usb_rx_bytes : start len[469792]
+ usb_tx_bytes : start len[4]
+ usb_rx_bytes : start len[4096]
+ fastboot_handle_command: continue
+ usb_tx_bytes : start len[4]
+ j...
+
+ U-Boot SPL 2022.10 (Sep 07 2026 - 11:31:13 +0000)
+ LPDDR5 total size: 16 GB, data rate: 6400 MT/s
+ DDR training consume 5625ms
+ ..
+ OpenSBI v1.9-72-g13a401f8
+ ____ _____ ____ _____
+ / __ \ / ____| _ \_ _|
+ | | | |_ __ ___ _ __ | (___ | |_) || |
+ | | | | '_ \ / _ \ '_ \ \___ \| _ < | |
+ | |__| | |_) | __/ | | |____) | |_) || |_
+ \____/| .__/ \___|_| |_|_____/|____/_____|
+ | |
+ |_|
+
+ Platform Name : SpacemiT K3 Pico-ITX
+ Platform Features : medeleg
+ Platform HART Count : 8
+ Platform HART Protection : pmp
+ Platform IPI Device : aclint-mswi
+ Platform Timer Device : aclint-mtimer @ 24000000Hz
+ Platform Console Device : uart8250
+ Platform HSM Device : spacemit-k3-hsm
+ Platform PMU Device : ---
+ Platform Reboot Device : spacemit-p1-reset
+ Platform Shutdown Device : spacemit-p1-reset
+ Platform Suspend Device : ---
+ Platform CPPC Device : ---
+ Firmware Base : 0x100000000
+ Firmware Size : 416 KB
+ Firmware RW Offset : 0x40000
+ Firmware RW Size : 160 KB
+ Firmware Heap Offset : 0x57000
+ Firmware Heap Size : 68 KB (total), 1 KB (reserved), 14 KB (used), 52 KB (free)
+ Firmware Scratch Size : 4096 B (total), 1472 B (used), 2624 B (free)
+ Runtime SBI Version : 3.0
+ Standard SBI Extensions : time,rfnc,ipi,base,hsm,srst,pmu,dbcn,fwft,legacy,dbtr,sse
+ Experimental SBI Extensions : none
+
+ Domain0 Name : root
+ Domain0 Init Order : 0xffffffff
+ Domain0 Boot HART : 0
+ Domain0 HARTs : 0x0*,0x1*,0x2*,0x3*,0x4*,0x5*,0x6*,0x7*
+ Domain0 Region00 : 0x0000000100000000-0x000000010003ffff M: (F,R,X) S/U: ()
+ Domain0 Region01 : 0x0000000100040000-0x000000010007ffff M: (F,R,W) S/U: ()
+ Domain0 Region02 : 0x00000000d4017000-0x00000000d4017fff M: (I,R,W) S/U: (R,W)
+ Domain0 Region03 : 0x00000000e081c000-0x00000000e081ffff M: (I,R,W) S/U: ()
+ Domain0 Region04 : 0x0000000000000000-0xffffffffffffffff M: () S/U: (R,W,X)
+ Domain0 Next Address : 0x0000000102000000
+ Domain0 Next Arg1 : 0x0000000102091398
+ Domain0 Next Mode : S-mode
+ Domain0 SysReset : yes
+ Domain0 SysSuspend : yes
+
+ Boot HART ID : 0
+ Boot HART Domain : root
+ Boot HART Priv Version : v1.12
+ Boot HART Base ISA : rv64imafdcbvhx
+ Boot HART ISA Extensions : smaia,smstateen,sscofpmf,sstc,zicntr,zihpm,smcntrpmf,zicboz,zicbom,svpbmt,sdtrig,svade,ssstateen,v,f,d
+ Boot HART PMP Count : 16
+ Boot HART PMP Granularity : 12 bits
+ Boot HART PMP Address Bits : 38
+ Boot HART MHPM Info : 16 (0x0007fff8)
+ Boot HART Debug Triggers : 4 triggers
+ Boot HART MIDELEG : 0x0000000000003666
+ Boot HART MEDELEG : 0x0000000000f0b509
+
+ <debug_uart>
+
+
+ U-Boot 2026.10-rc4-00501-g9fba7b59df42 (Sep 22 2026 - 13:08:33 +0000)
+
+ DRAM: 16 GiB
+ Core: 433 devices, 15 uclasses, devicetree: separate
+ Loading Environment from nowhere...Loading Environment from nowhere... OK
+ In: serial@d4017000
+ Out: serial@d4017000
+ Err: serial@d4017000
+ Net: No ethernet found.
+ =>
--
2.56.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v2 2/4] riscv: dts: spacemit: k3: add binman node
2026-10-02 1:03 ` [PATCH v2 2/4] riscv: dts: spacemit: k3: add binman node Yixun Lan
@ 2026-10-02 3:20 ` E Shattow
0 siblings, 0 replies; 8+ messages in thread
From: E Shattow @ 2026-10-02 3:20 UTC (permalink / raw)
To: Yixun Lan, u-boot
Cc: Yao Zi, Tim Ouyang, Leo Liang, Tom Rini, Michal Simek,
Raymond Mao, Hiago De Franco, Junhui Liu
Hi Yixun,
On 10/1/26 18:03, Yixun Lan wrote:
> SpacemiT K3 follow the standard riscv binman layout, which has opensbi
> and U-Boot proper, so include the common binman dtsi file.
>
> Signed-off-by: Yixun Lan <dlan@kernel.org>
> ---
> arch/riscv/dts/k3-u-boot.dtsi | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/arch/riscv/dts/k3-u-boot.dtsi b/arch/riscv/dts/k3-u-boot.dtsi
> new file mode 100644
> index 00000000000..f1c1c3ee6fd
> --- /dev/null
> +++ b/arch/riscv/dts/k3-u-boot.dtsi
> @@ -0,0 +1,6 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR MIT
> +/*
> + * Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> + */
> +
> +#include "binman.dtsi"
>
Please rename k3-u-boot.dtsi as similar to the target defconfig (e.g.
spacemit-k3-u-boot.dtsi) while avoiding any matches for the automatic
SOC/CPU/VENDOR inclusion routine of scripts/Makefile.lib:222. Add the
CONFIG_DEVICE_TREE_INCLUDES="spacemit-k3-u-boot.dtsi" board defconfig
option to ensure its inclusion.
The automatic inclusion of per-CPU -u-boot.dtsi does short-circuit any
automatic inclusion of per-target-board -u-boot.dtsi, and so becomes a
blocker in the situation where we would need to override something
per-board on a multi-board capable u-boot target (Pico-ITX, CoM260,
FML13v05, so I think this is likely).
Essentially repeating here my previous advice to Hal about adding a new
multi-board target from
https://lore.kernel.org/u-boot/ff0313ed-5d43-4603-aed4-6e41b2abed37@freeshell.de/
Thanks,
-E
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 1/4] board: spacemit: add SpacemiT K3 Pico-ITX
2026-10-02 1:03 ` [PATCH v2 1/4] board: spacemit: add SpacemiT K3 Pico-ITX Yixun Lan
@ 2026-10-02 7:02 ` E Shattow
2026-10-02 11:43 ` Yixun Lan
0 siblings, 1 reply; 8+ messages in thread
From: E Shattow @ 2026-10-02 7:02 UTC (permalink / raw)
To: Yixun Lan, u-boot
Cc: Yao Zi, Tim Ouyang, Leo Liang, Tom Rini, Michal Simek,
Raymond Mao, Hiago De Franco, Junhui Liu
Hi Yixun,
On 10/1/26 18:03, Yixun Lan wrote:
> Add initial support for K3 Pico-ITX board, in this version, the DRAM
> information is parsed from DTS "/memory" node. And with UART enabled,
> the U-Boot serial console works fine now.
>
> Signed-off-by: Yixun Lan <dlan@kernel.org>
> ---
> arch/riscv/Kconfig | 5 +++++
> arch/riscv/cpu/k3/Kconfig | 18 ++++++++++++++++++
> arch/riscv/cpu/k3/Makefile | 5 +++++
> arch/riscv/cpu/k3/dram.c | 21 +++++++++++++++++++++
> board/spacemit/k3/Kconfig | 30 ++++++++++++++++++++++++++++++
> board/spacemit/k3/MAINTAINERS | 8 ++++++++
> include/configs/k3.h | 13 +++++++++++++
> 7 files changed, 100 insertions(+)
>
> diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
> index c1b2890f1f3..386241efd4a 100644
> --- a/arch/riscv/Kconfig
> +++ b/arch/riscv/Kconfig
> @@ -53,6 +53,9 @@ config TARGET_SIPEED_MAIX
> config TARGET_SPACEMIT_K1
> bool "Support Spacemit K1 SoC"
>
> +config TARGET_SPACEMIT_K3
> + bool "Support SpacemiT K3 SoC"
> +
> config TARGET_STARFIVE_VISIONFIVE2
> bool "Support StarFive VisionFive2 Board"
> select BOARD_LATE_INIT
> @@ -124,6 +127,7 @@ source "board/sophgo/milkv_duo/Kconfig"
> source "board/sophgo/milkv_duo_256m/Kconfig"
> source "board/sophgo/licheerv_nano/Kconfig"
> source "board/spacemit/k1/Kconfig"
> +source "board/spacemit/k3/Kconfig"
> source "board/starfive/visionfive2/Kconfig"
> source "board/thead/th1520_lpi4a/Kconfig"
> source "board/xilinx/mbv/Kconfig"
> @@ -138,6 +142,7 @@ source "arch/riscv/cpu/mpfs/Kconfig"
> source "arch/riscv/cpu/generic/Kconfig"
> source "arch/riscv/cpu/jh7110/Kconfig"
> source "arch/riscv/cpu/k1/Kconfig"
> +source "arch/riscv/cpu/k3/Kconfig"
> source "arch/riscv/cpu/k230/Kconfig"
> source "arch/riscv/cpu/th1520/Kconfig"
>
> diff --git a/arch/riscv/cpu/k3/Kconfig b/arch/riscv/cpu/k3/Kconfig
> new file mode 100644
> index 00000000000..5474ac11243
> --- /dev/null
> +++ b/arch/riscv/cpu/k3/Kconfig
> @@ -0,0 +1,18 @@
> +# SPDX-License-Identifier: GPL-2.0-or-later
> +#
> +# Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> +
> +if TARGET_SPACEMIT_K3
> +
> +config SPACEMIT_K3
> + bool
> + select BINMAN
> + select ARCH_EARLY_INIT_R
> + select SYS_CACHE_SHIFT_6
> + imply CPU
> + imply CPU_RISCV
> + imply RISCV_TIMER if RISCV_SMODE
> + imply CMD_CPU
> + imply OF_UPSTREAM
> +
> +endif
> diff --git a/arch/riscv/cpu/k3/Makefile b/arch/riscv/cpu/k3/Makefile
> new file mode 100644
> index 00000000000..fba4e4b0a3f
> --- /dev/null
> +++ b/arch/riscv/cpu/k3/Makefile
> @@ -0,0 +1,5 @@
> +# SPDX-License-Identifier: GPL-2.0-or-later
> +#
> +# Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> +
> +obj-y += dram.o
> diff --git a/arch/riscv/cpu/k3/dram.c b/arch/riscv/cpu/k3/dram.c
> new file mode 100644
> index 00000000000..e20d35dc1bf
> --- /dev/null
> +++ b/arch/riscv/cpu/k3/dram.c
> @@ -0,0 +1,21 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> + */
> +
> +#include <fdtdec.h>
> +#include <init.h>
> +#include <linux/sizes.h>
> +#include <asm/global_data.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int dram_init(void)
> +{
> + return fdtdec_setup_mem_size_base();
> +}
> +
> +int dram_init_banksize(void)
> +{
> + return fdtdec_setup_memory_banksize();
> +}
> diff --git a/board/spacemit/k3/Kconfig b/board/spacemit/k3/Kconfig
> new file mode 100644
> index 00000000000..b0e423d829c
> --- /dev/null
> +++ b/board/spacemit/k3/Kconfig
> @@ -0,0 +1,30 @@
> +# SPDX-License-Identifier: GPL-2.0-or-later
> +#
> +# Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> +
> +if TARGET_SPACEMIT_K3
> +
> +config SYS_BOARD
> + default "k3"
> +
> +config SYS_VENDOR
> + default "spacemit"
> +
> +config SYS_CPU
> + default "k3"
> +
> +config SYS_CONFIG_NAME
> + default "k3"
> +
> +config TEXT_BASE
> + default 0x102000000
> +
> +config SPL_OPENSBI_LOAD_ADDR
> + hex
> + default 0x100000000
> +
> +config BOARD_SPECIFIC_OPTIONS
> + def_bool y
> + select SPACEMIT_K3
> +
> +endif
> diff --git a/board/spacemit/k3/MAINTAINERS b/board/spacemit/k3/MAINTAINERS
> new file mode 100644
> index 00000000000..34cf1ed4453
> --- /dev/null
> +++ b/board/spacemit/k3/MAINTAINERS
> @@ -0,0 +1,8 @@
> +SPACEMIT K3
> +M: Yixun Lan <dlan@kernel.org>
> +S: Maintained
> +F: arch/riscv/cpu/k3/
> +F: board/spacemit/k3/
> +F: configs/spacemit_k3_defconfig
> +F: include/configs/k3.h
> +F: arch/riscv/dts/k3-u-boot.dtsi
> diff --git a/include/configs/k3.h b/include/configs/k3.h
> new file mode 100644
> index 00000000000..83e4945d2b3
> --- /dev/null
> +++ b/include/configs/k3.h
> @@ -0,0 +1,13 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> +/*
> + * Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define CFG_SYS_NS16550_IER 0x40
> +
> +#define RISCV_SMODE_TIMER_FREQ 24000000
> +
> +#endif /* __CONFIG_H */
>
There is a Texas Instruments K3 SoC referred to as "k3" in u-boot
discussion. Let's not add to the confusion here on a global include file
that is named "configs/k3.h"
Please rename "include/configs/k3.h" as "include/configs/spacemit-k3.h"
or "include/configs/spacemit_k3.h" to be consistent with the target
defconfig name. "k1.h" global config header name may be renamed later
when development pace slows that it would not be too disruptive, and to
follow whatever hyphen or underscore delineation is decided for K3.
Thanks,
-E
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 1/4] board: spacemit: add SpacemiT K3 Pico-ITX
2026-10-02 7:02 ` E Shattow
@ 2026-10-02 11:43 ` Yixun Lan
0 siblings, 0 replies; 8+ messages in thread
From: Yixun Lan @ 2026-10-02 11:43 UTC (permalink / raw)
To: E Shattow
Cc: u-boot, Yao Zi, Tim Ouyang, Leo Liang, Tom Rini, Michal Simek,
Raymond Mao, Hiago De Franco, Junhui Liu
Hi E Shattow,
On 00:02 Fri 02 Oct , E Shattow wrote:
> Hi Yixun,
>
> On 10/1/26 18:03, Yixun Lan wrote:
> > Add initial support for K3 Pico-ITX board, in this version, the DRAM
> > information is parsed from DTS "/memory" node. And with UART enabled,
> > the U-Boot serial console works fine now.
> >
> > Signed-off-by: Yixun Lan <dlan@kernel.org>
> > ---
> > arch/riscv/Kconfig | 5 +++++
> > arch/riscv/cpu/k3/Kconfig | 18 ++++++++++++++++++
> > arch/riscv/cpu/k3/Makefile | 5 +++++
> > arch/riscv/cpu/k3/dram.c | 21 +++++++++++++++++++++
> > board/spacemit/k3/Kconfig | 30 ++++++++++++++++++++++++++++++
> > board/spacemit/k3/MAINTAINERS | 8 ++++++++
> > include/configs/k3.h | 13 +++++++++++++
> > 7 files changed, 100 insertions(+)
> >
> > diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
> > index c1b2890f1f3..386241efd4a 100644
> > --- a/arch/riscv/Kconfig
> > +++ b/arch/riscv/Kconfig
> > @@ -53,6 +53,9 @@ config TARGET_SIPEED_MAIX
> > config TARGET_SPACEMIT_K1
> > bool "Support Spacemit K1 SoC"
> >
> > +config TARGET_SPACEMIT_K3
> > + bool "Support SpacemiT K3 SoC"
> > +
> > config TARGET_STARFIVE_VISIONFIVE2
> > bool "Support StarFive VisionFive2 Board"
> > select BOARD_LATE_INIT
> > @@ -124,6 +127,7 @@ source "board/sophgo/milkv_duo/Kconfig"
> > source "board/sophgo/milkv_duo_256m/Kconfig"
> > source "board/sophgo/licheerv_nano/Kconfig"
> > source "board/spacemit/k1/Kconfig"
> > +source "board/spacemit/k3/Kconfig"
> > source "board/starfive/visionfive2/Kconfig"
> > source "board/thead/th1520_lpi4a/Kconfig"
> > source "board/xilinx/mbv/Kconfig"
> > @@ -138,6 +142,7 @@ source "arch/riscv/cpu/mpfs/Kconfig"
> > source "arch/riscv/cpu/generic/Kconfig"
> > source "arch/riscv/cpu/jh7110/Kconfig"
> > source "arch/riscv/cpu/k1/Kconfig"
> > +source "arch/riscv/cpu/k3/Kconfig"
> > source "arch/riscv/cpu/k230/Kconfig"
> > source "arch/riscv/cpu/th1520/Kconfig"
> >
> > diff --git a/arch/riscv/cpu/k3/Kconfig b/arch/riscv/cpu/k3/Kconfig
> > new file mode 100644
> > index 00000000000..5474ac11243
> > --- /dev/null
> > +++ b/arch/riscv/cpu/k3/Kconfig
> > @@ -0,0 +1,18 @@
> > +# SPDX-License-Identifier: GPL-2.0-or-later
> > +#
> > +# Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> > +
> > +if TARGET_SPACEMIT_K3
> > +
> > +config SPACEMIT_K3
> > + bool
> > + select BINMAN
> > + select ARCH_EARLY_INIT_R
> > + select SYS_CACHE_SHIFT_6
> > + imply CPU
> > + imply CPU_RISCV
> > + imply RISCV_TIMER if RISCV_SMODE
> > + imply CMD_CPU
> > + imply OF_UPSTREAM
> > +
> > +endif
> > diff --git a/arch/riscv/cpu/k3/Makefile b/arch/riscv/cpu/k3/Makefile
> > new file mode 100644
> > index 00000000000..fba4e4b0a3f
> > --- /dev/null
> > +++ b/arch/riscv/cpu/k3/Makefile
> > @@ -0,0 +1,5 @@
> > +# SPDX-License-Identifier: GPL-2.0-or-later
> > +#
> > +# Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> > +
> > +obj-y += dram.o
> > diff --git a/arch/riscv/cpu/k3/dram.c b/arch/riscv/cpu/k3/dram.c
> > new file mode 100644
> > index 00000000000..e20d35dc1bf
> > --- /dev/null
> > +++ b/arch/riscv/cpu/k3/dram.c
> > @@ -0,0 +1,21 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> > + */
> > +
> > +#include <fdtdec.h>
> > +#include <init.h>
> > +#include <linux/sizes.h>
> > +#include <asm/global_data.h>
> > +
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +int dram_init(void)
> > +{
> > + return fdtdec_setup_mem_size_base();
> > +}
> > +
> > +int dram_init_banksize(void)
> > +{
> > + return fdtdec_setup_memory_banksize();
> > +}
> > diff --git a/board/spacemit/k3/Kconfig b/board/spacemit/k3/Kconfig
> > new file mode 100644
> > index 00000000000..b0e423d829c
> > --- /dev/null
> > +++ b/board/spacemit/k3/Kconfig
> > @@ -0,0 +1,30 @@
> > +# SPDX-License-Identifier: GPL-2.0-or-later
> > +#
> > +# Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> > +
> > +if TARGET_SPACEMIT_K3
> > +
> > +config SYS_BOARD
> > + default "k3"
> > +
> > +config SYS_VENDOR
> > + default "spacemit"
> > +
> > +config SYS_CPU
> > + default "k3"
> > +
> > +config SYS_CONFIG_NAME
> > + default "k3"
> > +
> > +config TEXT_BASE
> > + default 0x102000000
> > +
> > +config SPL_OPENSBI_LOAD_ADDR
> > + hex
> > + default 0x100000000
> > +
> > +config BOARD_SPECIFIC_OPTIONS
> > + def_bool y
> > + select SPACEMIT_K3
> > +
> > +endif
> > diff --git a/board/spacemit/k3/MAINTAINERS b/board/spacemit/k3/MAINTAINERS
> > new file mode 100644
> > index 00000000000..34cf1ed4453
> > --- /dev/null
> > +++ b/board/spacemit/k3/MAINTAINERS
> > @@ -0,0 +1,8 @@
> > +SPACEMIT K3
> > +M: Yixun Lan <dlan@kernel.org>
> > +S: Maintained
> > +F: arch/riscv/cpu/k3/
> > +F: board/spacemit/k3/
> > +F: configs/spacemit_k3_defconfig
> > +F: include/configs/k3.h
> > +F: arch/riscv/dts/k3-u-boot.dtsi
> > diff --git a/include/configs/k3.h b/include/configs/k3.h
> > new file mode 100644
> > index 00000000000..83e4945d2b3
> > --- /dev/null
> > +++ b/include/configs/k3.h
> > @@ -0,0 +1,13 @@
> > +/* SPDX-License-Identifier: GPL-2.0-or-later */
> > +/*
> > + * Copyright (C) 2026 Yixun Lan <dlan@kernel.org>
> > + */
> > +
> > +#ifndef __CONFIG_H
> > +#define __CONFIG_H
> > +
> > +#define CFG_SYS_NS16550_IER 0x40
> > +
> > +#define RISCV_SMODE_TIMER_FREQ 24000000
> > +
> > +#endif /* __CONFIG_H */
> >
>
> There is a Texas Instruments K3 SoC referred to as "k3" in u-boot
> discussion. Let's not add to the confusion here on a global include file
> that is named "configs/k3.h"
>
> Please rename "include/configs/k3.h" as "include/configs/spacemit-k3.h"
> or "include/configs/spacemit_k3.h" to be consistent with the target
> defconfig name. "k1.h" global config header name may be renamed later
> when development pace slows that it would not be too disruptive, and to
> follow whatever hyphen or underscore delineation is decided for K3.
>
make sense, I will pick "spacemit-k3.h" as the config file name
--
Yixun Lan (dlan)
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2026-10-02 11:43 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-10-02 1:03 [PATCH v2 0/4] riscv: spacemit: Add support for K3 Pico-ITX board Yixun Lan
2026-10-02 1:03 ` [PATCH v2 1/4] board: spacemit: add SpacemiT K3 Pico-ITX Yixun Lan
2026-10-02 7:02 ` E Shattow
2026-10-02 11:43 ` Yixun Lan
2026-10-02 1:03 ` [PATCH v2 2/4] riscv: dts: spacemit: k3: add binman node Yixun Lan
2026-10-02 3:20 ` E Shattow
2026-10-02 1:03 ` [PATCH v2 3/4] configs: spacemit: Add K3 default configuration Yixun Lan
2026-10-02 1:03 ` [PATCH v2 4/4] doc: spacemit: k3: Add Pico-ITX board Yixun Lan
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.