[PATCH 5/5] media: ov2640: dt: add the device tree binding document

[laurent.pinchart@ideasonboard.com (Laurent Pinchart)]

Hi Josh,

Thank you for the patch.

On Monday 08 December 2014 19:29:07 Josh Wu wrote:
> Add the document for ov2640 dt.
> 
> Cc: devicetree at vger.kernel.org
> Signed-off-by: Josh Wu <josh.wu@atmel.com>
> ---
> v1 -> v2:
>   1. change the compatible string to be consistent with verdor file.

That's nice, but you still need to send a patch to add the ovti vendor prefix 
to Documentation/devicetree/bindings/vendor-prefixes.txt. It's not there yet.

>   2. change the clock and pins' name.
>   3. add missed pinctrl in example.
> 
>  .../devicetree/bindings/media/i2c/ov2640.txt       | 44 +++++++++++++++++++
>  1 file changed, 44 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov2640.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov2640.txt
> b/Documentation/devicetree/bindings/media/i2c/ov2640.txt new file mode
> 100644
> index 0000000..15be3cb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ov2640.txt
> @@ -0,0 +1,44 @@
> +* Omnivision ov2640 CMOS sensor
> +
> +The Omnivision OV2640 sensor support multiple resolutions output, such as
> +CIF, SVGA, UXGA. It also can support YUV422/420, RGB565/555 or raw RGB
> +output format.
> +
> +Required Properties :
> +- compatible: Must be "ovti,ov2640"
> +- clocks: reference master clock, if using external fixed clock, you
> +          no need to have such property.

That's not true anymore, the clocks property is mandatory in all cases. Just 
describe it as

- clocks: reference to the xvclk input clock.

> +- clock-names: Must be "xvclk", it means the master clock for ov2640.

I would drop "it means the master clock for ov2640".

> +Optional Properties:
> +- resetb-gpios: reset pin

- resetb-gpios: reference to the GPIO connected to the resetb pin, if any.

> +- pwdn-gpios: power down pin

- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any.

> +
> +The device node must contain one 'port' child node for its digital output
> +video port, in accordance with the video interface bindings defined in
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Example:
> +
> +	i2c1: i2c at f0018000 {
> +		ov2640: camera at 0x30 {
> +			compatible = "ovti,ov2640";
> +			reg = <0x30>;
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_pck1 &pinctrl_ov2640_pwdn 
&pinctrl_ov2640_reset>;
> +
> +			resetb-gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
> +			pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
> +
> +			clocks = <&pck1>;
> +			clock-names = "xvclk";
> +
> +			port {
> +				ov2640_0: endpoint {
> +					remote-endpoint = <&isi_0>;
> +					bus-width = <8>;
> +				};
> +			};
> +		};
> +	};

-- 
Regards,

Laurent Pinchart