From: khilman@baylibre.com (Kevin Hilman)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH v3 1/2] ARM64: dts: meson-axg: add ethernet mac controller
Date: Fri, 15 Dec 2017 11:29:31 -0800 [thread overview]
Message-ID: <7ho9mz94dg.fsf@baylibre.com> (raw)
In-Reply-To: <20171215021014.231308-2-yixun.lan@amlogic.com> (Yixun Lan's message of "Fri, 15 Dec 2017 10:10:13 +0800")
Yixun Lan <yixun.lan@amlogic.com> writes:
> Add DT info for the stmmac ethernet MAC which found in
> the Amlogic's Meson-AXG SoC, also describe the ethernet
> pinctrl & clock information here.
>
> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
This patch does not apply, and dependencies are not described.
> ---
> arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 54 ++++++++++++++++++++++++++++++
> 1 file changed, 54 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> index d356ce74ad89..94c4972222b7 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> @@ -7,6 +7,7 @@
> #include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/interrupt-controller/irq.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/axg-clkc.h>
>
> / {
> compatible = "amlogic,meson-axg";
> @@ -148,6 +149,19 @@
> #address-cells = <0>;
> };
>
> + ethmac: ethernet at ff3f0000 {
> + compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
> + reg = <0x0 0xff3f0000 0x0 0x10000
> + 0x0 0xff634540 0x0 0x8>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "macirq";
> + clocks = <&clkc CLKID_ETH>,
> + <&clkc CLKID_FCLK_DIV2>,
> + <&clkc CLKID_MPLL2>;
> + clock-names = "stmmaceth", "clkin0", "clkin1";
> + status = "disabled";
> + };
> +
> hiubus: bus at ff63c000 {
> compatible = "simple-bus";
> reg = <0x0 0xff63c000 0x0 0x1c00>;
Based on the hiubus node, presumably this depends on the patch from the
clock series.
> @@ -194,6 +208,46 @@
> #gpio-cells = <2>;
> gpio-ranges = <&pinctrl_periphs 0 0 86>;
> };
I'm not sure where this part is coming from, but it causes the rest of
it to not apply.
Please be sure to describe all dependencies.
Kevin
> +
> + eth_rgmii_x_pins: eth-x-rgmii {
> + mux {
> + groups = "eth_mdio_x",
> + "eth_mdc_x",
> + "eth_rgmii_rx_clk_x",
> + "eth_rx_dv_x",
> + "eth_rxd0_x",
> + "eth_rxd1_x",
> + "eth_rxd2_rgmii",
> + "eth_rxd3_rgmii",
> + "eth_rgmii_tx_clk",
> + "eth_txen_x",
> + "eth_txd0_x",
> + "eth_txd1_x",
> + "eth_txd2_rgmii",
> + "eth_txd3_rgmii";
> + function = "eth";
> + };
> + };
> +
> + eth_rgmii_y_pins: eth-y-rgmii {
> + mux {
> + groups = "eth_mdio_y",
> + "eth_mdc_y",
> + "eth_rgmii_rx_clk_y",
> + "eth_rx_dv_y",
> + "eth_rxd0_y",
> + "eth_rxd1_y",
> + "eth_rxd2_rgmii",
> + "eth_rxd3_rgmii",
> + "eth_rgmii_tx_clk",
> + "eth_txen_y",
> + "eth_txd0_y",
> + "eth_txd1_y",
> + "eth_txd2_rgmii",
> + "eth_txd3_rgmii";
> + function = "eth";
> + };
> + };
> };
> };
WARNING: multiple messages have this Message-ID (diff)
From: khilman@baylibre.com (Kevin Hilman)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 1/2] ARM64: dts: meson-axg: add ethernet mac controller
Date: Fri, 15 Dec 2017 11:29:31 -0800 [thread overview]
Message-ID: <7ho9mz94dg.fsf@baylibre.com> (raw)
In-Reply-To: <20171215021014.231308-2-yixun.lan@amlogic.com> (Yixun Lan's message of "Fri, 15 Dec 2017 10:10:13 +0800")
Yixun Lan <yixun.lan@amlogic.com> writes:
> Add DT info for the stmmac ethernet MAC which found in
> the Amlogic's Meson-AXG SoC, also describe the ethernet
> pinctrl & clock information here.
>
> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
This patch does not apply, and dependencies are not described.
> ---
> arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 54 ++++++++++++++++++++++++++++++
> 1 file changed, 54 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> index d356ce74ad89..94c4972222b7 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> @@ -7,6 +7,7 @@
> #include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/interrupt-controller/irq.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/axg-clkc.h>
>
> / {
> compatible = "amlogic,meson-axg";
> @@ -148,6 +149,19 @@
> #address-cells = <0>;
> };
>
> + ethmac: ethernet at ff3f0000 {
> + compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
> + reg = <0x0 0xff3f0000 0x0 0x10000
> + 0x0 0xff634540 0x0 0x8>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "macirq";
> + clocks = <&clkc CLKID_ETH>,
> + <&clkc CLKID_FCLK_DIV2>,
> + <&clkc CLKID_MPLL2>;
> + clock-names = "stmmaceth", "clkin0", "clkin1";
> + status = "disabled";
> + };
> +
> hiubus: bus at ff63c000 {
> compatible = "simple-bus";
> reg = <0x0 0xff63c000 0x0 0x1c00>;
Based on the hiubus node, presumably this depends on the patch from the
clock series.
> @@ -194,6 +208,46 @@
> #gpio-cells = <2>;
> gpio-ranges = <&pinctrl_periphs 0 0 86>;
> };
I'm not sure where this part is coming from, but it causes the rest of
it to not apply.
Please be sure to describe all dependencies.
Kevin
> +
> + eth_rgmii_x_pins: eth-x-rgmii {
> + mux {
> + groups = "eth_mdio_x",
> + "eth_mdc_x",
> + "eth_rgmii_rx_clk_x",
> + "eth_rx_dv_x",
> + "eth_rxd0_x",
> + "eth_rxd1_x",
> + "eth_rxd2_rgmii",
> + "eth_rxd3_rgmii",
> + "eth_rgmii_tx_clk",
> + "eth_txen_x",
> + "eth_txd0_x",
> + "eth_txd1_x",
> + "eth_txd2_rgmii",
> + "eth_txd3_rgmii";
> + function = "eth";
> + };
> + };
> +
> + eth_rgmii_y_pins: eth-y-rgmii {
> + mux {
> + groups = "eth_mdio_y",
> + "eth_mdc_y",
> + "eth_rgmii_rx_clk_y",
> + "eth_rx_dv_y",
> + "eth_rxd0_y",
> + "eth_rxd1_y",
> + "eth_rxd2_rgmii",
> + "eth_rxd3_rgmii",
> + "eth_rgmii_tx_clk",
> + "eth_txen_y",
> + "eth_txd0_y",
> + "eth_txd1_y",
> + "eth_txd2_rgmii",
> + "eth_txd3_rgmii";
> + function = "eth";
> + };
> + };
> };
> };
WARNING: multiple messages have this Message-ID (diff)
From: Kevin Hilman <khilman-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
To: Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Neil Armstrong
<narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>,
Jerome Brunet <jbrunet-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>,
Giuseppe Cavallaro <peppe.cavallaro-qxv4g6HH51o@public.gmane.org>,
Alexandre Torgue <alexandre.torgue-qxv4g6HH51o@public.gmane.org>,
Carlo Caione <carlo-KA+7E9HrN00dnm+yROfE0A@public.gmane.org>,
linux-amlogic-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
netdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: Re: [PATCH v3 1/2] ARM64: dts: meson-axg: add ethernet mac controller
Date: Fri, 15 Dec 2017 11:29:31 -0800 [thread overview]
Message-ID: <7ho9mz94dg.fsf@baylibre.com> (raw)
In-Reply-To: <20171215021014.231308-2-yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org> (Yixun Lan's message of "Fri, 15 Dec 2017 10:10:13 +0800")
Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org> writes:
> Add DT info for the stmmac ethernet MAC which found in
> the Amlogic's Meson-AXG SoC, also describe the ethernet
> pinctrl & clock information here.
>
> Reviewed-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
> Signed-off-by: Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
This patch does not apply, and dependencies are not described.
> ---
> arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 54 ++++++++++++++++++++++++++++++
> 1 file changed, 54 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> index d356ce74ad89..94c4972222b7 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> @@ -7,6 +7,7 @@
> #include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/interrupt-controller/irq.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/axg-clkc.h>
>
> / {
> compatible = "amlogic,meson-axg";
> @@ -148,6 +149,19 @@
> #address-cells = <0>;
> };
>
> + ethmac: ethernet@ff3f0000 {
> + compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
> + reg = <0x0 0xff3f0000 0x0 0x10000
> + 0x0 0xff634540 0x0 0x8>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "macirq";
> + clocks = <&clkc CLKID_ETH>,
> + <&clkc CLKID_FCLK_DIV2>,
> + <&clkc CLKID_MPLL2>;
> + clock-names = "stmmaceth", "clkin0", "clkin1";
> + status = "disabled";
> + };
> +
> hiubus: bus@ff63c000 {
> compatible = "simple-bus";
> reg = <0x0 0xff63c000 0x0 0x1c00>;
Based on the hiubus node, presumably this depends on the patch from the
clock series.
> @@ -194,6 +208,46 @@
> #gpio-cells = <2>;
> gpio-ranges = <&pinctrl_periphs 0 0 86>;
> };
I'm not sure where this part is coming from, but it causes the rest of
it to not apply.
Please be sure to describe all dependencies.
Kevin
> +
> + eth_rgmii_x_pins: eth-x-rgmii {
> + mux {
> + groups = "eth_mdio_x",
> + "eth_mdc_x",
> + "eth_rgmii_rx_clk_x",
> + "eth_rx_dv_x",
> + "eth_rxd0_x",
> + "eth_rxd1_x",
> + "eth_rxd2_rgmii",
> + "eth_rxd3_rgmii",
> + "eth_rgmii_tx_clk",
> + "eth_txen_x",
> + "eth_txd0_x",
> + "eth_txd1_x",
> + "eth_txd2_rgmii",
> + "eth_txd3_rgmii";
> + function = "eth";
> + };
> + };
> +
> + eth_rgmii_y_pins: eth-y-rgmii {
> + mux {
> + groups = "eth_mdio_y",
> + "eth_mdc_y",
> + "eth_rgmii_rx_clk_y",
> + "eth_rx_dv_y",
> + "eth_rxd0_y",
> + "eth_rxd1_y",
> + "eth_rxd2_rgmii",
> + "eth_rxd3_rgmii",
> + "eth_rgmii_tx_clk",
> + "eth_txen_y",
> + "eth_txd0_y",
> + "eth_txd1_y",
> + "eth_txd2_rgmii",
> + "eth_txd3_rgmii";
> + function = "eth";
> + };
> + };
> };
> };
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: Kevin Hilman <khilman@baylibre.com>
To: Yixun Lan <yixun.lan@amlogic.com>
Cc: <devicetree@vger.kernel.org>,
Neil Armstrong <narmstrong@baylibre.com>,
Jerome Brunet <jbrunet@baylibre.com>,
Giuseppe Cavallaro <peppe.cavallaro@st.com>,
Alexandre Torgue <alexandre.torgue@st.com>,
Carlo Caione <carlo@caione.org>,
<linux-amlogic@lists.infradead.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <netdev@vger.kernel.org>
Subject: Re: [PATCH v3 1/2] ARM64: dts: meson-axg: add ethernet mac controller
Date: Fri, 15 Dec 2017 11:29:31 -0800 [thread overview]
Message-ID: <7ho9mz94dg.fsf@baylibre.com> (raw)
In-Reply-To: <20171215021014.231308-2-yixun.lan@amlogic.com> (Yixun Lan's message of "Fri, 15 Dec 2017 10:10:13 +0800")
Yixun Lan <yixun.lan@amlogic.com> writes:
> Add DT info for the stmmac ethernet MAC which found in
> the Amlogic's Meson-AXG SoC, also describe the ethernet
> pinctrl & clock information here.
>
> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
This patch does not apply, and dependencies are not described.
> ---
> arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 54 ++++++++++++++++++++++++++++++
> 1 file changed, 54 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> index d356ce74ad89..94c4972222b7 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> @@ -7,6 +7,7 @@
> #include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/interrupt-controller/irq.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/axg-clkc.h>
>
> / {
> compatible = "amlogic,meson-axg";
> @@ -148,6 +149,19 @@
> #address-cells = <0>;
> };
>
> + ethmac: ethernet@ff3f0000 {
> + compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
> + reg = <0x0 0xff3f0000 0x0 0x10000
> + 0x0 0xff634540 0x0 0x8>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "macirq";
> + clocks = <&clkc CLKID_ETH>,
> + <&clkc CLKID_FCLK_DIV2>,
> + <&clkc CLKID_MPLL2>;
> + clock-names = "stmmaceth", "clkin0", "clkin1";
> + status = "disabled";
> + };
> +
> hiubus: bus@ff63c000 {
> compatible = "simple-bus";
> reg = <0x0 0xff63c000 0x0 0x1c00>;
Based on the hiubus node, presumably this depends on the patch from the
clock series.
> @@ -194,6 +208,46 @@
> #gpio-cells = <2>;
> gpio-ranges = <&pinctrl_periphs 0 0 86>;
> };
I'm not sure where this part is coming from, but it causes the rest of
it to not apply.
Please be sure to describe all dependencies.
Kevin
> +
> + eth_rgmii_x_pins: eth-x-rgmii {
> + mux {
> + groups = "eth_mdio_x",
> + "eth_mdc_x",
> + "eth_rgmii_rx_clk_x",
> + "eth_rx_dv_x",
> + "eth_rxd0_x",
> + "eth_rxd1_x",
> + "eth_rxd2_rgmii",
> + "eth_rxd3_rgmii",
> + "eth_rgmii_tx_clk",
> + "eth_txen_x",
> + "eth_txd0_x",
> + "eth_txd1_x",
> + "eth_txd2_rgmii",
> + "eth_txd3_rgmii";
> + function = "eth";
> + };
> + };
> +
> + eth_rgmii_y_pins: eth-y-rgmii {
> + mux {
> + groups = "eth_mdio_y",
> + "eth_mdc_y",
> + "eth_rgmii_rx_clk_y",
> + "eth_rx_dv_y",
> + "eth_rxd0_y",
> + "eth_rxd1_y",
> + "eth_rxd2_rgmii",
> + "eth_rxd3_rgmii",
> + "eth_rgmii_tx_clk",
> + "eth_txen_y",
> + "eth_txd0_y",
> + "eth_txd1_y",
> + "eth_txd2_rgmii",
> + "eth_txd3_rgmii";
> + function = "eth";
> + };
> + };
> };
> };
WARNING: multiple messages have this Message-ID (diff)
From: Kevin Hilman <khilman-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
To: Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Cc: <devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>,
Neil Armstrong
<narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>,
Jerome Brunet <jbrunet-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>,
Giuseppe Cavallaro <peppe.cavallaro-qxv4g6HH51o@public.gmane.org>,
Alexandre Torgue <alexandre.torgue-qxv4g6HH51o@public.gmane.org>,
Carlo Caione <carlo-KA+7E9HrN00dnm+yROfE0A@public.gmane.org>,
<linux-amlogic-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org>,
<linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org>,
<linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>,
<netdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>
Subject: Re: [PATCH v3 1/2] ARM64: dts: meson-axg: add ethernet mac controller
Date: Fri, 15 Dec 2017 11:29:31 -0800 [thread overview]
Message-ID: <7ho9mz94dg.fsf@baylibre.com> (raw)
In-Reply-To: <20171215021014.231308-2-yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org> (Yixun Lan's message of "Fri, 15 Dec 2017 10:10:13 +0800")
Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org> writes:
> Add DT info for the stmmac ethernet MAC which found in
> the Amlogic's Meson-AXG SoC, also describe the ethernet
> pinctrl & clock information here.
>
> Reviewed-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
> Signed-off-by: Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
This patch does not apply, and dependencies are not described.
> ---
> arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 54 ++++++++++++++++++++++++++++++
> 1 file changed, 54 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> index d356ce74ad89..94c4972222b7 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> @@ -7,6 +7,7 @@
> #include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/interrupt-controller/irq.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/axg-clkc.h>
>
> / {
> compatible = "amlogic,meson-axg";
> @@ -148,6 +149,19 @@
> #address-cells = <0>;
> };
>
> + ethmac: ethernet@ff3f0000 {
> + compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
> + reg = <0x0 0xff3f0000 0x0 0x10000
> + 0x0 0xff634540 0x0 0x8>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "macirq";
> + clocks = <&clkc CLKID_ETH>,
> + <&clkc CLKID_FCLK_DIV2>,
> + <&clkc CLKID_MPLL2>;
> + clock-names = "stmmaceth", "clkin0", "clkin1";
> + status = "disabled";
> + };
> +
> hiubus: bus@ff63c000 {
> compatible = "simple-bus";
> reg = <0x0 0xff63c000 0x0 0x1c00>;
Based on the hiubus node, presumably this depends on the patch from the
clock series.
> @@ -194,6 +208,46 @@
> #gpio-cells = <2>;
> gpio-ranges = <&pinctrl_periphs 0 0 86>;
> };
I'm not sure where this part is coming from, but it causes the rest of
it to not apply.
Please be sure to describe all dependencies.
Kevin
> +
> + eth_rgmii_x_pins: eth-x-rgmii {
> + mux {
> + groups = "eth_mdio_x",
> + "eth_mdc_x",
> + "eth_rgmii_rx_clk_x",
> + "eth_rx_dv_x",
> + "eth_rxd0_x",
> + "eth_rxd1_x",
> + "eth_rxd2_rgmii",
> + "eth_rxd3_rgmii",
> + "eth_rgmii_tx_clk",
> + "eth_txen_x",
> + "eth_txd0_x",
> + "eth_txd1_x",
> + "eth_txd2_rgmii",
> + "eth_txd3_rgmii";
> + function = "eth";
> + };
> + };
> +
> + eth_rgmii_y_pins: eth-y-rgmii {
> + mux {
> + groups = "eth_mdio_y",
> + "eth_mdc_y",
> + "eth_rgmii_rx_clk_y",
> + "eth_rx_dv_y",
> + "eth_rxd0_y",
> + "eth_rxd1_y",
> + "eth_rxd2_rgmii",
> + "eth_rxd3_rgmii",
> + "eth_rgmii_tx_clk",
> + "eth_txen_y",
> + "eth_txd0_y",
> + "eth_txd1_y",
> + "eth_txd2_rgmii",
> + "eth_txd3_rgmii";
> + function = "eth";
> + };
> + };
> };
> };
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2017-12-15 19:29 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-15 2:10 [PATCH v3 0/2] Add ethernet support for Meson-AXG SoC Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 2:10 ` [PATCH v3 1/2] ARM64: dts: meson-axg: add ethernet mac controller Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 19:29 ` Kevin Hilman [this message]
2017-12-15 19:29 ` Kevin Hilman
2017-12-15 19:29 ` Kevin Hilman
2017-12-15 19:29 ` Kevin Hilman
2017-12-15 19:29 ` Kevin Hilman
2017-12-16 3:38 ` Yixun Lan
2017-12-16 3:38 ` Yixun Lan
2017-12-16 3:38 ` Yixun Lan
2017-12-16 3:38 ` Yixun Lan
2017-12-15 2:10 ` [PATCH v3 2/2] ARM64: dts: meson-axg: enable ethernet for A113D S400 board Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 2:10 ` Yixun Lan
2017-12-15 19:31 ` Kevin Hilman
2017-12-15 19:31 ` Kevin Hilman
2017-12-15 19:31 ` Kevin Hilman
2017-12-15 19:31 ` Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=7ho9mz94dg.fsf@baylibre.com \
--to=khilman@baylibre.com \
--cc=linus-amlogic@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.