[PATCH v3 2/2] drivers/irqchip: gicv3: add workaround for Synquacer pre-ITS

[marc.zyngier@arm.com (Marc Zyngier)]

On Fri, Oct 13 2017 at  1:50:06 pm BST, Rob Herring <robh+dt@kernel.org> wrote:
> On Fri, Oct 13, 2017 at 4:47 AM, Marc Zyngier <marc.zyngier@arm.com> wrote:
>> [+Mark]
>>
>> On 12/10/17 23:24, Ard Biesheuvel wrote:
>>> On 12 October 2017 at 22:34, Rob Herring <robh+dt@kernel.org> wrote:
>>>> On Thu, Oct 12, 2017 at 1:32 PM, Ard Biesheuvel
>>>> <ard.biesheuvel@linaro.org> wrote:
>>>>> The Socionext Synquacer SoC's implementation of GICv3 has a so-called
>>>>> 'pre-ITS', which maps 32-bit writes targeted at a separate window of
>>>>> size '4 << device_id_bits' onto writes to GITS_TRANSLATER with device
>>>>> ID taken from bits [device_id_bits + 1:2] of the window offset.
>>>>> Writes that target GITS_TRANSLATER directly are reported as originating
>>>>> from device ID #0.
>>>>>
>>>>> So add a workaround for this. Given that this breaks isolation, clear
>>>>> the IRQ_DOMAIN_FLAG_MSI_REMAP flag as well.
>>>>>
>>>>> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
>>>>> ---
>>>>>  Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt |  4 ++
>>>>>  arch/arm64/Kconfig                                                    |  8 +++
>>>>>  drivers/irqchip/irq-gic-v3-its.c                                      | 63 +++++++++++++++++++-
>>>>>  3 files changed, 72 insertions(+), 3 deletions(-)
>>>>>
>>>>> diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
>>>>> index 4c29cdab0ea5..0798a61bbf99 100644
>>>>> --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
>>>>> +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
>>>>> @@ -75,6 +75,10 @@ These nodes must have the following properties:
>>>>>  - reg: Specifies the base physical address and size of the ITS
>>>>>    registers.
>>>>>
>>>>> +Optional:
>>>>> +- socionext,synquacer-pre-its: (u32, u32) tuple describing the host address
>>>>> +  and size of the pre-ITS window, as implemented on the Socionext Synquacer SoC
>>>>
>>>> Sounds like a separate h/w block to me and addresses should be in
>>>> "reg". I would suggest you define a separate node for the pre-its
>>>> block and then use of_find_compatible_node() from the GIC driver to
>>>> retrieve the node and whatever you need from it. Or do an SoC specific
>>>> compatible string for the GIC and let that imply whatever information
>>>> you need. Then the next quirk doesn't need a DT update.
>>>>
>>>
>>> For my understanding, you mean either
>>>
>>>     gic: interrupt-controller at 30000000 {
>>>         compatible = "arm,gic-v3";
>>>         ...
>>>
>>>         its: gic-its at 30020000 {
>>>             compatible = "arm,gic-v3-its";
>>>             reg = <0x0 0x30020000 0x0 0x20000>;
>>>             #msi-cells = <1>;
>>>             msi-controller;
>>>         };
>>>     };
>>>
>>>     preits at 58000000 {
>>>         compatible = "socionext,synquacer-pre-its";
>>>         reg = <0x0 0x58000000 0x0 0x200000>;
>>>         msi-slave = <&its>;
>>>     };
>>>
>>> or
>>>
>>>     gic: interrupt-controller at 30000000 {
>>>         compatible = "arm,gic-v3";
>>>         ...
>>>
>>>         its: gic-its at 30020000 {
>>>             compatible = "socionext,synquacer-pre-its", "arm,gic-v3-its";
>>>             reg = <0x0 0x30020000 0x0 0x20000>,
>>>                   <0x0 0x58000000 0x0 0x200000>;
>>>             #msi-cells = <1>;
>>>             msi-controller;
>>>         };
>>>     };
>>>
>>> right?
>>>
>>> Marc, what do you think? IIRC we did discuss option #2 at some point,
>>> but I don't remember if/why we rejected it.
>>
>> I dislike #2 because these registers are not part of the regular ITS,
>> and would get in the way of potential extensions of the ITS (I don't
>> know of any, but just in case...).
>>
>> I also dislike #1 as the "msi-slave" part is both ugly and confusing
>> (are we writing to the ITS? to the pre-ITS?).
>
> Why do you need this? Are you ever going to have multiple pre-its's?
> That's why I suggested just using of_find_compatible_node().

Who knows? This thing should have never existed the first place, but
someone felt the need to add this horror. I wouldn't be surprised if the
same vendor came up with the same broken design in a "bigger and better"
version of this SoC.

>> How about putting the pre-its node *inside* the its node itself? It
>> makes it obvious which pre-ITS corresponds to which ITS, and it leaves
>> the ITS regs untouched.
>
> Not wild about this, but it's fine if you do need to handle multiple
> instances.

Multiple ITS instances are pretty common. And broken designs seem to be
the norm rather than the exception, unfortunately.

Thanks,

	M.
-- 
Jazz is not dead. It just smells funny.