From: Kalle Valo <kvalo@codeaurora.org>
To: Wen Gong <wgong@codeaurora.org>
Cc: ath11k@lists.infradead.org, linux-wireless@vger.kernel.org
Subject: Re: [PATCH v3 0/3] ath11k: add feature for device recovery
Date: Mon, 15 Nov 2021 14:53:07 +0200 [thread overview]
Message-ID: <87h7cdh970.fsf@codeaurora.org> (raw)
In-Reply-To: <20211015035459.14190-1-wgong@codeaurora.org> (Wen Gong's message of "Thu, 14 Oct 2021 23:54:56 -0400")
Wen Gong <wgong@codeaurora.org> writes:
> From: Wen Gong <quic_wgong@quicinc.com>
>
> v3: remove time_left set but not used in
> "ath11k: add synchronization operation between reconfigure of mac80211 and ath11k_base"
>
> v2: s/initilized/initialized in commit log of patch
> "ath11k: add synchronization operation between reconfigure of mac80211 and ath11k_base"
>
> Add support for device recovery.
>
> Wen Gong (3):
> ath11k: add ath11k_qmi_free_resource() for recovery
> ath11k: add support for device recovery for QCA6390
> ath11k: add synchronization operation between reconfigure of mac80211
> and ath11k_base
I did some quick testing (commit 4716d5bb1e16 in pending branch) and it
does not seem to work for me:
oot@nuc1:~# echo assert > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash
root@nuc1:~# iw wlan0 scan
command failed: Connection timed out (-110)
root@nuc1:~#
Kernel logs have:
[ 118.903092] ath11k_pci 0000:06:00.0: BAR 0: assigned [mem 0xdb000000-0xdbffffff 64bit]
[ 118.925164] ath11k_pci 0000:06:00.0: MSI vectors: 32
[ 118.925285] ath11k_pci 0000:06:00.0: qca6390 hw2.0
[ 119.093214] mhi mhi0: Requested to power ON
[ 119.095430] mhi mhi0: Power on setup success
[ 119.423735] mhi mhi0: Wait for device to enter SBL or Mission mode
[ 119.543030] ath11k_pci 0000:06:00.0: chip_id 0x0 chip_family 0xb board_id 0xff soc_id 0xffffffff
[ 119.543197] ath11k_pci 0000:06:00.0: fw_version 0x101c06cc fw_build_timestamp 2020-06-24 19:50 fw_build_id
[ 230.101077] ip (2367) used greatest stack depth: 24384 bytes left
[ 283.663895] ath11k_pci 0000:06:00.0: simulating firmware assert crash
[ 283.738422] ath11k_pci 0000:06:00.0: firmware crashed: MHI_CB_SYS_ERROR
[ 295.236831] ath11k_pci 0000:06:00.0: wmi command 12290 timeout
[ 295.237937] ath11k_pci 0000:06:00.0: failed to send WMI_STOP_SCAN_CMDID
[ 295.238467] ath11k_pci 0000:06:00.0: failed to stop wmi scan: -11
[ 295.240049] ath11k_pci 0000:06:00.0: failed to stop scan: -11
[ 295.240558] ath11k_pci 0000:06:00.0: failed to start hw scan: -110
Also there should be a clear ath11k_warn() message when firmware
recovery was successful, I could not find one from patches.
--
https://patchwork.kernel.org/project/linux-wireless/list/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
--
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k
WARNING: multiple messages have this Message-ID (diff)
From: Kalle Valo <kvalo@codeaurora.org>
To: Wen Gong <wgong@codeaurora.org>
Cc: ath11k@lists.infradead.org, linux-wireless@vger.kernel.org
Subject: Re: [PATCH v3 0/3] ath11k: add feature for device recovery
Date: Mon, 15 Nov 2021 14:53:07 +0200 [thread overview]
Message-ID: <87h7cdh970.fsf@codeaurora.org> (raw)
In-Reply-To: <20211015035459.14190-1-wgong@codeaurora.org> (Wen Gong's message of "Thu, 14 Oct 2021 23:54:56 -0400")
Wen Gong <wgong@codeaurora.org> writes:
> From: Wen Gong <quic_wgong@quicinc.com>
>
> v3: remove time_left set but not used in
> "ath11k: add synchronization operation between reconfigure of mac80211 and ath11k_base"
>
> v2: s/initilized/initialized in commit log of patch
> "ath11k: add synchronization operation between reconfigure of mac80211 and ath11k_base"
>
> Add support for device recovery.
>
> Wen Gong (3):
> ath11k: add ath11k_qmi_free_resource() for recovery
> ath11k: add support for device recovery for QCA6390
> ath11k: add synchronization operation between reconfigure of mac80211
> and ath11k_base
I did some quick testing (commit 4716d5bb1e16 in pending branch) and it
does not seem to work for me:
oot@nuc1:~# echo assert > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash
root@nuc1:~# iw wlan0 scan
command failed: Connection timed out (-110)
root@nuc1:~#
Kernel logs have:
[ 118.903092] ath11k_pci 0000:06:00.0: BAR 0: assigned [mem 0xdb000000-0xdbffffff 64bit]
[ 118.925164] ath11k_pci 0000:06:00.0: MSI vectors: 32
[ 118.925285] ath11k_pci 0000:06:00.0: qca6390 hw2.0
[ 119.093214] mhi mhi0: Requested to power ON
[ 119.095430] mhi mhi0: Power on setup success
[ 119.423735] mhi mhi0: Wait for device to enter SBL or Mission mode
[ 119.543030] ath11k_pci 0000:06:00.0: chip_id 0x0 chip_family 0xb board_id 0xff soc_id 0xffffffff
[ 119.543197] ath11k_pci 0000:06:00.0: fw_version 0x101c06cc fw_build_timestamp 2020-06-24 19:50 fw_build_id
[ 230.101077] ip (2367) used greatest stack depth: 24384 bytes left
[ 283.663895] ath11k_pci 0000:06:00.0: simulating firmware assert crash
[ 283.738422] ath11k_pci 0000:06:00.0: firmware crashed: MHI_CB_SYS_ERROR
[ 295.236831] ath11k_pci 0000:06:00.0: wmi command 12290 timeout
[ 295.237937] ath11k_pci 0000:06:00.0: failed to send WMI_STOP_SCAN_CMDID
[ 295.238467] ath11k_pci 0000:06:00.0: failed to stop wmi scan: -11
[ 295.240049] ath11k_pci 0000:06:00.0: failed to stop scan: -11
[ 295.240558] ath11k_pci 0000:06:00.0: failed to start hw scan: -110
Also there should be a clear ath11k_warn() message when firmware
recovery was successful, I could not find one from patches.
--
https://patchwork.kernel.org/project/linux-wireless/list/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
next prev parent reply other threads:[~2021-11-15 12:53 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-15 3:54 [PATCH v3 0/3] ath11k: add feature for device recovery Wen Gong
2021-10-15 3:54 ` Wen Gong
2021-10-15 3:54 ` [PATCH v3 1/3] ath11k: add ath11k_qmi_free_resource() for recovery Wen Gong
2021-10-15 3:54 ` Wen Gong
2021-10-15 3:54 ` [PATCH v3 2/3] ath11k: add support for device recovery for QCA6390 Wen Gong
2021-10-15 3:54 ` Wen Gong
2021-10-15 3:54 ` [PATCH v3 3/3] ath11k: add synchronization operation between reconfigure of mac80211 and ath11k_base Wen Gong
2021-10-15 3:54 ` Wen Gong
2021-11-15 12:53 ` Kalle Valo [this message]
2021-11-15 12:53 ` [PATCH v3 0/3] ath11k: add feature for device recovery Kalle Valo
2021-11-16 4:19 ` Wen Gong
2021-11-16 4:19 ` Wen Gong
2021-11-17 8:08 ` Kalle Valo
2021-11-17 8:08 ` Kalle Valo
2021-11-17 9:35 ` Wen Gong
2021-11-17 9:35 ` Wen Gong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87h7cdh970.fsf@codeaurora.org \
--to=kvalo@codeaurora.org \
--cc=ath11k@lists.infradead.org \
--cc=linux-wireless@vger.kernel.org \
--cc=wgong@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.