IMX53QSB-R can not boot from microSD

IMX53QSB-R can not boot from microSD

[jojo]

[-- Attachment #1: Type: text/plain, Size: 1741 bytes --]

Hi, 
This board is supported by yocto project ?

i use the command "sudo dd if=fsl-image-gui-imx53qsb-20131024020930.rootfs.sdcard of=/dev/sdb bs=1M" to put image in to microSD, and

i use the command "MACHINE=imx53qsb source setup-environment build-imx53qsb"

to create the fsl-image-gui to boot, some error is reported as bellow :

In:    serial
Out:   serial
Err:   serial
CPU:   Freescale i.MX53 family rev2.1 at 1000 MHz
Reset cause: POR
Net:   FEC
Warning: failed to set MAC address

Hit any key to stop autoboot:  0 
MMC: no card present
mmc0(part 0) is current device
MMC: no card present
Booting from net ...
*** ERROR: `ethaddr' not set
*** ERROR: `ethaddr' not set
Wrong Image Format for bootm command
ERROR: can't get kernel image!


i reference the doc "i.MX53_START_Linux_BSP_UserGuide.pdf" to set microSD parameters in boot line as bellow:

MX53LOCO U-Boot > setenv bootargs_base 'setenv bootargs console=ttymxc0,115200'
MX53LOCO U-Boot > setenv bootargs_mmc 'setenv bootargs ${bootargs} root=/dev/mmcblk0p1 rootwait rw video=mxcdi1fb:GBR24,VGA-XGA di1_primary vga'
MX53LOCO U-Boot > setenv bootcmd_mmc 'run bootargs_base bootargs_mmc;mmc dev 0;mmc read ${loadaddr} 0x800 0x1800;bootm'
MX53LOCO U-Boot > setenv bootcmd 'run bootcmd_mmc'
MX53LOCO U-Boot > saveenv
Saving Environment to MMC...
MMC: no card present
MMC init failed
MX53LOCO U-Boot > run bootcmd
MMC: no card present
mmc0(part 0) is current device

MMC read: dev # 0, block # 2048, count 6144 ... MMC: no card present
MMC: block number 0x2000 exceeds max(0x0)
0 blocks read: ERROR
Wrong Image Format for bootm command
ERROR: can't get kernel image!


Anyone have any idea for this issue ? 

Thanks,

- Jojo


[-- Attachment #2: Type: text/html, Size: 2797 bytes --]

Re: IMX53QSB-R can not boot from microSD

[Eric Bénard]

Hi Jojo,

Le Thu, 24 Oct 2013 12:46:12 +0800,
jojo <rjiejie@gmail.com> a écrit :
> This board is supported by yocto project ?
> 
yes

> Anyone have any idea for this issue ? 
> 
don't change anything on the environment the image generated by Yocto
is ready to boot and not in sync with
i.MX53_START_Linux_BSP_UserGuide.pdf which is LTIB based.

Eric

回复： IMX53QSB-R can not boot from microSD

[jojo]

[-- Attachment #1: Type: text/plain, Size: 1400 bytes --]

Hi,  
I rebuild the imx53qsb completely and boot failed also as bellow :

and i do not change anything about for yocto dora except DL_DIR to redirect to "DL_DIR = "${TOPDIR}/../../downloads""

U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)

Board: MX53 LOCO
I2C:   ready
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
MMC: no card present
MMC init failed
Using default environment

In:    serial
Out:   serial
Err:   serial
CPU:   Freescale i.MX53 family rev2.1 at 1000 MHz
Reset cause: POR
Net:   FEC
Warning: failed to set MAC address

Hit any key to stop autoboot:  0  
MMC: no card present
mmc0(part 0) is current device
MMC: no card present
Booting from net ...
*** ERROR: `ethaddr' not set
*** ERROR: `ethaddr' not set
Wrong Image Format for bootm command
ERROR: can't get kernel image!
MX53LOCO U-Boot >  


BTW, my board is IMX53-START-R  

Thanks,

- Jojo


在 2013年10月24日星期四，下午3:13，Eric Bénard 写道：

> Hi Jojo,
>  
> Le Thu, 24 Oct 2013 12:46:12 +0800,
> jojo <rjiejie@gmail.com (mailto:rjiejie@gmail.com)> a écrit :
> > This board is supported by yocto project ?
>  
> yes
>  
> > Anyone have any idea for this issue ?  
> don't change anything on the environment the image generated by Yocto
> is ready to boot and not in sync with
> i.MX53_START_Linux_BSP_UserGuide.pdf which is LTIB based.
>  
> Eric  


[-- Attachment #2: Type: text/html, Size: 2758 bytes --]

Re: 回复： IMX53QSB-R can not boot from microSD

[Eric Bénard]

Hi Jojo,

Le Fri, 25 Oct 2013 14:49:31 +0800,
jojo <rjiejie@gmail.com> a écrit :
> I rebuild the imx53qsb completely and boot failed also as bellow :
> 
> and i do not change anything about for yocto dora except DL_DIR to redirect to "DL_DIR = "${TOPDIR}/../../downloads""
> 
> U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)
> 
> Board: MX53 LOCO
> I2C:   ready
> DRAM:  1 GiB
> MMC:   FSL_SDHC: 0, FSL_SDHC: 1
> MMC: no card present
> MMC init failed

can you try with an other SDCard it seems u-boot fails to initialize
this one.
I'll try dora on MX53QSB asap.

Eric

回复： IMX53QSB-R can not boot from microSD

[jojo]

[-- Attachment #1: Type: text/plain, Size: 882 bytes --]

Hi,  
I use microSD to boot my board,

and i have done two microSD card,

either of them is failed :(

Thanks,

- Jojo


在 2013年10月25日星期五，下午3:18，Eric Bénard 写道：

> Hi Jojo,
>  
> Le Fri, 25 Oct 2013 14:49:31 +0800,
> jojo <rjiejie@gmail.com (mailto:rjiejie@gmail.com)> a écrit :
> > I rebuild the imx53qsb completely and boot failed also as bellow :
> >  
> > and i do not change anything about for yocto dora except DL_DIR to redirect to "DL_DIR = "${TOPDIR}/../../downloads""
> >  
> > U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)
> >  
> > Board: MX53 LOCO
> > I2C: ready
> > DRAM: 1 GiB
> > MMC: FSL_SDHC: 0, FSL_SDHC: 1
> > MMC: no card present
> > MMC init failed
> >  
>  
>  
> can you try with an other SDCard it seems u-boot fails to initialize
> this one.
> I'll try dora on MX53QSB asap.
>  
> Eric  


[-- Attachment #2: Type: text/html, Size: 1955 bytes --]

回复： IMX53QSB-R can not boot from microSD

[jojo]

[-- Attachment #1: Type: text/plain, Size: 1114 bytes --]

Hi  
Help ….

no none met this issue ?

OMG...

Thanks,

- Jojo


在 2013年10月25日星期五，下午3:44，jojo 写道：

> Hi,  
> I use microSD to boot my board,
>  
> and i have done two microSD card,
>  
> either of them is failed :(
>  
> Thanks,
>  
> - Jojo
>  
>  
> 在 2013年10月25日星期五，下午3:18，Eric Bénard 写道：
>  
> > Hi Jojo,
> >  
> > Le Fri, 25 Oct 2013 14:49:31 +0800,
> > jojo <rjiejie@gmail.com (mailto:rjiejie@gmail.com)> a écrit :
> > > I rebuild the imx53qsb completely and boot failed also as bellow :
> > >  
> > > and i do not change anything about for yocto dora except DL_DIR to redirect to "DL_DIR = "${TOPDIR}/../../downloads""
> > >  
> > > U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)
> > >  
> > > Board: MX53 LOCO
> > > I2C: ready
> > > DRAM: 1 GiB
> > > MMC: FSL_SDHC: 0, FSL_SDHC: 1
> > > MMC: no card present
> > > MMC init failed
> > >  
> >  
> >  
> > can you try with an other SDCard it seems u-boot fails to initialize
> > this one.
> > I'll try dora on MX53QSB asap.
> >  
> > Eric  
>  


[-- Attachment #2: Type: text/html, Size: 2786 bytes --]

Re: IMX53QSB-R can not boot from microSD

[Fabio Estevam]

On Thu, Oct 24, 2013 at 2:46 AM, jojo <rjiejie@gmail.com> wrote:
> Hi,
> This board is supported by yocto project ?
>
> i use the command "sudo dd
> if=fsl-image-gui-imx53qsb-20131024020930.rootfs.sdcard of=/dev/sdb bs=1M" to
> put image in to microSD, and
>
> i use the command "MACHINE=imx53qsb source setup-environment build-imx53qsb"
>
> to create the fsl-image-gui to boot, some error is reported as bellow :
>
> In:    serial
> Out:   serial
> Err:   serial
> CPU:   Freescale i.MX53 family rev2.1 at 1000 MHz
> Reset cause: POR
> Net:   FEC
> Warning: failed to set MAC address
>
> Hit any key to stop autoboot:  0
> MMC: no card present
> mmc0(part 0) is current device
> MMC: no card present

I would suggest you to debug why you get 'MMC: no card present'.

Regards,

Fabio Estevam

Re: 回复： IMX53QSB-R can not boot from microSD

[Daiane Angolini]

On 10/28/2013 09:22 AM, jojo wrote:
> Hi
> Help ….
>
> no none met this issue ?
U-Boot 2013.10 (Oct 28 2013 - 10:51:11)

Board: MX53 LOCO
I2C:   ready
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1


I tested with core-image-base, and I was able to reach the user-space 
prompt.

Daiane


> OMG...
>
> Thanks,
>
> - Jojo
>
> 在 2013年10月25日星期五，下午3:44，jojo 写道：
>
>> Hi,
>> I use microSD to boot my board,
>>
>> and i have done two microSD card,
>> either of them is failed :(
>>
>> Thanks,
>>
>> - Jojo
>>
>> 在 2013年10月25日星期五，下午3:18，Eric Bénard 写道：
>>
>>> Hi Jojo,
>>>
>>> Le Fri, 25 Oct 2013 14:49:31 +0800,
>>> jojo <rjiejie@gmail.com <mailto:rjiejie@gmail.com>> a écrit :
>>>> I rebuild the imx53qsb completely and boot failed also as bellow :
>>>>
>>>> and i do not change anything about for yocto dora except DL_DIR to
>>>> redirect to "DL_DIR = "${TOPDIR}/../../downloads""
>>>>
>>>> U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)
>>>>
>>>> Board: MX53 LOCO
>>>> I2C: ready
>>>> DRAM: 1 GiB
>>>> MMC: FSL_SDHC: 0, FSL_SDHC: 1
>>>> MMC: no card present
>>>> MMC init failed
>>>
>>> can you try with an other SDCard it seems u-boot fails to initialize
>>> this one.
>>> I'll try dora on MX53QSB asap.
>>>
>>> Eric
>>
>
>
>
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale
>


-- 
Daiane

回复： 回复： MX53QSB-R can not boot from microSD

[jojo]

[-- Attachment #1: Type: text/plain, Size: 2267 bytes --]

Hi,  
I use the command "sudo dd if=fsl-image-gui-imx53qsb-20131024020930.rootfs.sdcard of=/dev/sdb bs=1M" to put image in to microSD,

is it right about for my step to burning SD image into microSD ?

BTW, what's your step of burning ? i think about my command is wrong :(  

Thanks,

- Jojo


在 2013年10月28日星期一，下午11:07，Daiane Angolini 写道：

> On 10/28/2013 09:22 AM, jojo wrote:
> > Hi
> > Help ….
> >  
> > no none met this issue ?
> U-Boot 2013.10 (Oct 28 2013 - 10:51:11)
>  
> Board: MX53 LOCO
> I2C: ready
> DRAM: 1 GiB
> MMC: FSL_SDHC: 0, FSL_SDHC: 1
>  
>  
> I tested with core-image-base, and I was able to reach the user-space  
> prompt.
>  
> Daiane
>  
>  
> > OMG...
> >  
> > Thanks,
> >  
> > - Jojo
> >  
> > 在 2013年10月25日星期五，下午3:44，jojo 写道：
> >  
> > > Hi,
> > > I use microSD to boot my board,
> > >  
> > > and i have done two microSD card,
> > > either of them is failed :(
> > >  
> > > Thanks,
> > >  
> > > - Jojo
> > >  
> > > 在 2013年10月25日星期五，下午3:18，Eric Bénard 写道：
> > >  
> > > > Hi Jojo,
> > > >  
> > > > Le Fri, 25 Oct 2013 14:49:31 +0800,
> > > > jojo <rjiejie@gmail.com <mailto:rjiejie@gmail.com>> a écrit :
> > > > > I rebuild the imx53qsb completely and boot failed also as bellow :
> > > > >  
> > > > > and i do not change anything about for yocto dora except DL_DIR to
> > > > > redirect to "DL_DIR = "${TOPDIR}/../../downloads""
> > > > >  
> > > > > U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)
> > > > >  
> > > > > Board: MX53 LOCO
> > > > > I2C: ready
> > > > > DRAM: 1 GiB
> > > > > MMC: FSL_SDHC: 0, FSL_SDHC: 1
> > > > > MMC: no card present
> > > > > MMC init failed
> > > > >  
> > > >  
> > > >  
> > > > can you try with an other SDCard it seems u-boot fails to initialize
> > > > this one.
> > > > I'll try dora on MX53QSB asap.
> > > >  
> > > > Eric
> >  
> >  
> >  
> > _______________________________________________
> > meta-freescale mailing list
> > meta-freescale@yoctoproject.org (mailto:meta-freescale@yoctoproject.org)
> > https://lists.yoctoproject.org/listinfo/meta-freescale
> >  
>  
>  
>  
> --  
> Daiane
>  
>  



[-- Attachment #2: Type: text/html, Size: 3834 bytes --]

Re: 回复： 回复： IMX53QSB-R can not boot from microSD

[Daiane Angolini]

On 10/29/2013 01:07 AM, jojo wrote:
> Hi,
> I use the command "sudo dd
> if=fsl-image-gui-imx53qsb-20131024020930.rootfs.sdcard of=/dev/sdb
> bs=1M" to put image in to microSD,
> is it right about for my step to burning SD image into microSD ?

Hi Jojo

I copy using:

sudo dd if=fsl-image-gui-imx53qsb-20131024020930.rootfs.sdcard of=/dev/sdb



Daiane
>
> BTW, what's your step of burning ? i think about my command is wrong :(
>
> Thanks,
>
> - Jojo
>
> 在 2013年10月28日星期一，下午11:07，Daiane Angolini 写道：
>
>> On 10/28/2013 09:22 AM, jojo wrote:
>>> Hi
>>> Help ….
>>>
>>> no none met this issue ?
>> U-Boot 2013.10 (Oct 28 2013 - 10:51:11)
>>
>> Board: MX53 LOCO
>> I2C: ready
>> DRAM: 1 GiB
>> MMC: FSL_SDHC: 0, FSL_SDHC: 1
>>
>>
>> I tested with core-image-base, and I was able to reach the user-space
>> prompt.
>>
>> Daiane
>>
>>
>>> OMG...
>>>
>>> Thanks,
>>>
>>> - Jojo
>>>
>>> 在 2013年10月25日星期五，下午3:44，jojo 写道：
>>>
>>>> Hi,
>>>> I use microSD to boot my board,
>>>>
>>>> and i have done two microSD card,
>>>> either of them is failed :(
>>>>
>>>> Thanks,
>>>>
>>>> - Jojo
>>>>
>>>> 在 2013年10月25日星期五，下午3:18，Eric Bénard 写道：
>>>>
>>>>> Hi Jojo,
>>>>>
>>>>> Le Fri, 25 Oct 2013 14:49:31 +0800,
>>>>> jojo <rjiejie@gmail.com <mailto:rjiejie@gmail.com>> a écrit :
>>>>>> I rebuild the imx53qsb completely and boot failed also as bellow :
>>>>>>
>>>>>> and i do not change anything about for yocto dora except DL_DIR to
>>>>>> redirect to "DL_DIR = "${TOPDIR}/../../downloads""
>>>>>>
>>>>>> U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)
>>>>>>
>>>>>> Board: MX53 LOCO
>>>>>> I2C: ready
>>>>>> DRAM: 1 GiB
>>>>>> MMC: FSL_SDHC: 0, FSL_SDHC: 1
>>>>>> MMC: no card present
>>>>>> MMC init failed
>>>>>
>>>>> can you try with an other SDCard it seems u-boot fails to initialize
>>>>> this one.
>>>>> I'll try dora on MX53QSB asap.
>>>>>
>>>>> Eric
>>>
>>>
>>>
>>> _______________________________________________
>>> meta-freescale mailing list
>>> meta-freescale@yoctoproject.org <mailto:meta-freescale@yoctoproject.org>
>>> https://lists.yoctoproject.org/listinfo/meta-freescale
>>
>>
>> --
>> Daiane
>


-- 
Daiane

Re: 回复： IMX53QSB-R can not boot from microSD

[Jose Mª Ferreiro]

El 25/10/2013 9:18, Eric Bénard escribió:
> Hi Jojo,
>
> Le Fri, 25 Oct 2013 14:49:31 +0800,
> jojo <rjiejie@gmail.com> a écrit :
>> I rebuild the imx53qsb completely and boot failed also as bellow :
>>
>> and i do not change anything about for yocto dora except DL_DIR to redirect to "DL_DIR = "${TOPDIR}/../../downloads""
>>
>> U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)
>>
>> Board: MX53 LOCO
>> I2C:   ready
>> DRAM:  1 GiB
>> MMC:   FSL_SDHC: 0, FSL_SDHC: 1
>> MMC: no card present
>> MMC init failed
> can you try with an other SDCard it seems u-boot fails to initialize
> this one.
> I'll try dora on MX53QSB asap.
>
> Eric
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale

Hello

A similar problem here: just a week ago, we got a imx6qsabresd board. We 
compiled a image for it and burn it into a microSD (with adapter). 
u-boot does not recognize the card. We burned it into a normal SD card 
and the board started well.

It seems as if u-boot does not recognize the microSD card.

Thank you

Re: 回复： IMX53QSB-R can not boot from microSD

[Daiane Angolini]

On 10/29/2013 01:03 PM, Jose Mª Ferreiro wrote:
>
> El 25/10/2013 9:18, Eric Bénard escribió:
>> Hi Jojo,
>>
>> Le Fri, 25 Oct 2013 14:49:31 +0800,
>> jojo <rjiejie@gmail.com> a écrit :
>>> I rebuild the imx53qsb completely and boot failed also as bellow :
>>>
>>> and i do not change anything about for yocto dora except DL_DIR to
>>> redirect to "DL_DIR = "${TOPDIR}/../../downloads""
>>>
>>> U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)
>>>
>>> Board: MX53 LOCO
>>> I2C:   ready
>>> DRAM:  1 GiB
>>> MMC:   FSL_SDHC: 0, FSL_SDHC: 1
>>> MMC: no card present
>>> MMC init failed
>> can you try with an other SDCard it seems u-boot fails to initialize
>> this one.
>> I'll try dora on MX53QSB asap.
>>
>> Eric
>> _______________________________________________
>> meta-freescale mailing list
>> meta-freescale@yoctoproject.org
>> https://lists.yoctoproject.org/listinfo/meta-freescale
>
> Hello
>
> A similar problem here: just a week ago, we got a imx6qsabresd board. We
> compiled a image for it and burn it into a microSD (with adapter).
> u-boot does not recognize the card. We burned it into a normal SD card
> and the board started well.
>
> It seems as if u-boot does not recognize the microSD card.

I've been using microSD for imx53qsb with u-boot mainline since 2 years 
ago, and I have never faced this problem.

Sometimes I need to hardreset (unplug power supply) because some QSB 
does not have a good reset button, but microsd always worked for me


>
> Thank you
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale


-- 
Daiane

Re: 回复： IMX53QSB-R can not boot from microSD

[Mario Domenech Goulart]

Hi,

On Tue, 29 Oct 2013 13:12:21 -0200 Daiane Angolini <daiane.angolini@freescale.com> wrote:

> On 10/29/2013 01:03 PM, Jose Mª Ferreiro wrote:
>>
>> El 25/10/2013 9:18, Eric Bénard escribió:
>>>
>>> Le Fri, 25 Oct 2013 14:49:31 +0800, jojo <rjiejie@gmail.com> a écrit :
>>>> I rebuild the imx53qsb completely and boot failed also as bellow :
>>>>
>>>> and i do not change anything about for yocto dora except DL_DIR to
>>>> redirect to "DL_DIR = "${TOPDIR}/../../downloads""
>>>>
>>>> U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)
>>>>
>>>> Board: MX53 LOCO
>>>> I2C:   ready
>>>> DRAM:  1 GiB
>>>> MMC:   FSL_SDHC: 0, FSL_SDHC: 1
>>>> MMC: no card present
>>>> MMC init failed
>>>
>>> can you try with an other SDCard it seems u-boot fails to initialize
>>> this one.  I'll try dora on MX53QSB asap.
>>
>> A similar problem here: just a week ago, we got a imx6qsabresd
>> board. We compiled a image for it and burn it into a microSD (with
>> adapter).  u-boot does not recognize the card. We burned it into a
>> normal SD card and the board started well.
>>
>> It seems as if u-boot does not recognize the microSD card.
>
> I've been using microSD for imx53qsb with u-boot mainline since 2
> years ago, and I have never faced this problem.
>
> Sometimes I need to hardreset (unplug power supply) because some QSB
> does not have a good reset button, but microsd always worked for me

I once had problems with an SD card adapter.  Don't remember which board
it was, but just replacing the adapter did the trick.

Best wishes.
Mario
-- 
http://www.ossystems.com.br

回复： 回复： MX53QSB-R can not boot from microSD

[jojo]

[-- Attachment #1: Type: text/plain, Size: 3933 bytes --]

Hi,  
I use the command like you to copy image besides failing as bellow also,

i think about u-boot does not recognize the microSD really, and there is no

normal SD adapter in my IMX53QSB :(  

i just have microSD in my board ….any ideal about this ?

BTW, my microSD is "SanDisk 4GB class 4"


U-Boot 2013.10 (Oct 28 2013 - 17:28:17)

Board: MX53 LOCO
I2C:   ready
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
MMC: no card present
MMC init failed
Using default environment

In:    serial
Out:   serial
Err:   serial
CPU:   Freescale i.MX53 family rev2.1 at 1000 MHz
Reset cause: POR
Net:   FEC
Warning: failed to set MAC address

Hit any key to stop autoboot:  0  
MMC: no card present
mmc0(part 0) is current device
MMC: no card present
Booting from net ...
*** ERROR: `ethaddr' not set
*** ERROR: `ethaddr' not set
Wrong Image Format for bootm command
ERROR: can't get kernel image!
MX53LOCO U-Boot >  



Thanks,

- Jojo


在 2013年10月29日星期二，下午6:20，Daiane Angolini 写道：

> On 10/29/2013 01:07 AM, jojo wrote:
> > Hi,
> > I use the command "sudo dd
> > if=fsl-image-gui-imx53qsb-20131024020930.rootfs.sdcard of=/dev/sdb
> > bs=1M" to put image in to microSD,
> > is it right about for my step to burning SD image into microSD ?
> >  
>  
>  
> Hi Jojo
>  
> I copy using:
>  
> sudo dd if=fsl-image-gui-imx53qsb-20131024020930.rootfs.sdcard of=/dev/sdb
>  
>  
>  
> Daiane
> >  
> > BTW, what's your step of burning ? i think about my command is wrong :(
> >  
> > Thanks,
> >  
> > - Jojo
> >  
> > 在 2013年10月28日星期一，下午11:07，Daiane Angolini 写道：
> >  
> > > On 10/28/2013 09:22 AM, jojo wrote:
> > > > Hi
> > > > Help ….
> > > >  
> > > > no none met this issue ?
> > > U-Boot 2013.10 (Oct 28 2013 - 10:51:11)
> > >  
> > > Board: MX53 LOCO
> > > I2C: ready
> > > DRAM: 1 GiB
> > > MMC: FSL_SDHC: 0, FSL_SDHC: 1
> > >  
> > >  
> > > I tested with core-image-base, and I was able to reach the user-space
> > > prompt.
> > >  
> > > Daiane
> > >  
> > >  
> > > > OMG...
> > > >  
> > > > Thanks,
> > > >  
> > > > - Jojo
> > > >  
> > > > 在 2013年10月25日星期五，下午3:44，jojo 写道：
> > > >  
> > > > > Hi,
> > > > > I use microSD to boot my board,
> > > > >  
> > > > > and i have done two microSD card,
> > > > > either of them is failed :(
> > > > >  
> > > > > Thanks,
> > > > >  
> > > > > - Jojo
> > > > >  
> > > > > 在 2013年10月25日星期五，下午3:18，Eric Bénard 写道：
> > > > >  
> > > > > > Hi Jojo,
> > > > > >  
> > > > > > Le Fri, 25 Oct 2013 14:49:31 +0800,
> > > > > > jojo <rjiejie@gmail.com <mailto:rjiejie@gmail.com>> a écrit :
> > > > > > > I rebuild the imx53qsb completely and boot failed also as bellow :
> > > > > > >  
> > > > > > > and i do not change anything about for yocto dora except DL_DIR to
> > > > > > > redirect to "DL_DIR = "${TOPDIR}/../../downloads""
> > > > > > >  
> > > > > > > U-Boot 2013.10-rc3 (Oct 25 2013 - 13:28:32)
> > > > > > >  
> > > > > > > Board: MX53 LOCO
> > > > > > > I2C: ready
> > > > > > > DRAM: 1 GiB
> > > > > > > MMC: FSL_SDHC: 0, FSL_SDHC: 1
> > > > > > > MMC: no card present
> > > > > > > MMC init failed
> > > > > > >  
> > > > > >  
> > > > > >  
> > > > > > can you try with an other SDCard it seems u-boot fails to initialize
> > > > > > this one.
> > > > > > I'll try dora on MX53QSB asap.
> > > > > >  
> > > > > > Eric
> > > >  
> > > >  
> > > >  
> > > > _______________________________________________
> > > > meta-freescale mailing list
> > > > meta-freescale@yoctoproject.org <mailto:meta-freescale@yoctoproject.org>
> > > > https://lists.yoctoproject.org/listinfo/meta-freescale
> > > >  
> > >  
> > >  
> > >  
> > > --
> > > Daiane
> > >  
> >  
> >  
>  
>  
>  
> --  
> Daiane
>  
>  



[-- Attachment #2: Type: text/html, Size: 6093 bytes --]

Re: 回复： 回复： IMX53QSB-R can not boot from microSD

[Otavio Salvador]

Hello,

On Wed, Oct 30, 2013 at 12:14 AM, jojo <rjiejie@gmail.com> wrote:
> I use the command like you to copy image besides failing as bellow also,
>
> i think about u-boot does not recognize the microSD really, and there is no
> normal SD adapter in my IMX53QSB :(
>
> i just have microSD in my board ….any ideal about this ?
>
> BTW, my microSD is "SanDisk 4GB class 4"
>
>
> U-Boot 2013.10 (Oct 28 2013 - 17:28:17)
>
> Board: MX53 LOCO
> I2C:   ready
> DRAM:  1 GiB
> MMC:   FSL_SDHC: 0, FSL_SDHC: 1
> MMC: no card present
> MMC init failed
> Using default environment
>
> In:    serial
> Out:   serial
> Err:   serial
> CPU:   Freescale i.MX53 family rev2.1 at 1000 MHz
> Reset cause: POR
> Net:   FEC
> Warning: failed to set MAC address
>
> Hit any key to stop autoboot:  0
> MMC: no card present
> mmc0(part 0) is current device
> MMC: no card present
> Booting from net ...
> *** ERROR: `ethaddr' not set
> *** ERROR: `ethaddr' not set
> Wrong Image Format for bootm command
> ERROR: can't get kernel image!
> MX53LOCO U-Boot >

Did you try replacing your uSD card?

This is an indication of uSD card or connector problems (more likely
the first). U-Boot is failing to 'see' your card.

-- 
Otavio Salvador                             O.S. Systems
http://www.ossystems.com.br        http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854            Mobile: +1 (347) 903-9750

Re: 回复： 回复： IMX53QSB-R can not boot from microSD

[Fabio Estevam]

On Wed, Oct 30, 2013 at 12:14 AM, jojo <rjiejie@gmail.com> wrote:
> Hi,
> I use the command like you to copy image besides failing as bellow also,
>
> i think about u-boot does not recognize the microSD really, and there is no
> normal SD adapter in my IMX53QSB :(
>
> i just have microSD in my board ….any ideal about this ?
>
> BTW, my microSD is "SanDisk 4GB class 4"
>
>
> U-Boot 2013.10 (Oct 28 2013 - 17:28:17)
>
> Board: MX53 LOCO
> I2C:   ready
> DRAM:  1 GiB
> MMC:   FSL_SDHC: 0, FSL_SDHC: 1
> MMC: no card present
> MMC init failed

Can previous versions of U-boot detect your card?

Regards,

Fabio Estevam