From: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
To: Reza Arbab <arbab@linux.vnet.ibm.com>,
Michael Ellerman <mpe@ellerman.id.au>,
Benjamin Herrenschmidt <benh@kernel.crashing.org>,
Paul Mackerras <paulus@samba.org>,
Rob Herring <robh+dt@kernel.org>,
Frank Rowand <frowand.list@gmail.com>,
Andrew Morton <akpm@linux-foundation.org>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>,
Nathan Fontenot <nfont@linux.vnet.ibm.com>,
Stewart Smith <stewart@linux.vnet.ibm.com>,
Alistair Popple <apopple@au1.ibm.com>,
Balbir Singh <bsingharora@gmail.com>,
Tang Chen <tangchen@cn.fujitsu.com>,
linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org,
devicetree@vger.kernel.org, linux-mm@kvack.org
Subject: Re: [PATCH v4 4/5] mm: make processing of movable_node arch-specific
Date: Fri, 07 Oct 2016 12:07:11 +0530 [thread overview]
Message-ID: <87zimgmzqg.fsf@linux.vnet.ibm.com> (raw)
In-Reply-To: <1475778995-1420-5-git-send-email-arbab@linux.vnet.ibm.com>
Reza Arbab <arbab@linux.vnet.ibm.com> writes:
> Currently, CONFIG_MOVABLE_NODE depends on X86_64. In preparation to
> enable it for other arches, we need to factor a detail which is unique
> to x86 out of the generic mm code.
>
> Specifically, as documented in kernel-parameters.txt, the use of
> "movable_node" should remain restricted to x86:
>
> movable_node [KNL,X86] Boot-time switch to enable the effects
> of CONFIG_MOVABLE_NODE=y. See mm/Kconfig for details.
>
> This option tells x86 to find movable nodes identified by the ACPI SRAT.
> On other arches, it would have no benefit, only the undesired side
> effect of setting bottom-up memblock allocation.
>
> Since #ifdef CONFIG_MOVABLE_NODE will no longer be enough to restrict
> this option to x86, move it to an arch-specific compilation unit
> instead.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
>
> Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com>
> ---
> arch/x86/mm/numa.c | 35 ++++++++++++++++++++++++++++++++++-
> mm/memory_hotplug.c | 31 -------------------------------
> 2 files changed, 34 insertions(+), 32 deletions(-)
>
> diff --git a/arch/x86/mm/numa.c b/arch/x86/mm/numa.c
> index fb68210..e95cab4 100644
> --- a/arch/x86/mm/numa.c
> +++ b/arch/x86/mm/numa.c
> @@ -887,6 +887,38 @@ EXPORT_SYMBOL(cpumask_of_node);
> #endif /* !CONFIG_DEBUG_PER_CPU_MAPS */
>
> #ifdef CONFIG_MEMORY_HOTPLUG
> +
> +static int __init cmdline_parse_movable_node(char *p)
> +{
> +#ifdef CONFIG_MOVABLE_NODE
> + /*
> + * Memory used by the kernel cannot be hot-removed because Linux
> + * cannot migrate the kernel pages. When memory hotplug is
> + * enabled, we should prevent memblock from allocating memory
> + * for the kernel.
> + *
> + * ACPI SRAT records all hotpluggable memory ranges. But before
> + * SRAT is parsed, we don't know about it.
> + *
> + * The kernel image is loaded into memory at very early time. We
> + * cannot prevent this anyway. So on NUMA system, we set any
> + * node the kernel resides in as un-hotpluggable.
> + *
> + * Since on modern servers, one node could have double-digit
> + * gigabytes memory, we can assume the memory around the kernel
> + * image is also un-hotpluggable. So before SRAT is parsed, just
> + * allocate memory near the kernel image to try the best to keep
> + * the kernel away from hotpluggable memory.
> + */
> + memblock_set_bottom_up(true);
> + movable_node_enabled = true;
> +#else
> + pr_warn("movable_node option not supported\n");
> +#endif
> + return 0;
> +}
> +early_param("movable_node", cmdline_parse_movable_node);
> +
> int memory_add_physaddr_to_nid(u64 start)
> {
> struct numa_meminfo *mi = &numa_meminfo;
> @@ -899,4 +931,5 @@ int memory_add_physaddr_to_nid(u64 start)
> return nid;
> }
> EXPORT_SYMBOL_GPL(memory_add_physaddr_to_nid);
> -#endif
> +
> +#endif /* CONFIG_MEMORY_HOTPLUG */
> diff --git a/mm/memory_hotplug.c b/mm/memory_hotplug.c
> index 9d29ba0..79c709a 100644
> --- a/mm/memory_hotplug.c
> +++ b/mm/memory_hotplug.c
> @@ -1738,37 +1738,6 @@ static bool can_offline_normal(struct zone *zone, unsigned long nr_pages)
> }
> #endif /* CONFIG_MOVABLE_NODE */
>
> -static int __init cmdline_parse_movable_node(char *p)
> -{
> -#ifdef CONFIG_MOVABLE_NODE
> - /*
> - * Memory used by the kernel cannot be hot-removed because Linux
> - * cannot migrate the kernel pages. When memory hotplug is
> - * enabled, we should prevent memblock from allocating memory
> - * for the kernel.
> - *
> - * ACPI SRAT records all hotpluggable memory ranges. But before
> - * SRAT is parsed, we don't know about it.
> - *
> - * The kernel image is loaded into memory at very early time. We
> - * cannot prevent this anyway. So on NUMA system, we set any
> - * node the kernel resides in as un-hotpluggable.
> - *
> - * Since on modern servers, one node could have double-digit
> - * gigabytes memory, we can assume the memory around the kernel
> - * image is also un-hotpluggable. So before SRAT is parsed, just
> - * allocate memory near the kernel image to try the best to keep
> - * the kernel away from hotpluggable memory.
> - */
> - memblock_set_bottom_up(true);
> - movable_node_enabled = true;
> -#else
> - pr_warn("movable_node option not supported\n");
> -#endif
> - return 0;
> -}
> -early_param("movable_node", cmdline_parse_movable_node);
> -
> /* check which state of node_states will be changed when offline memory */
> static void node_states_check_changes_offline(unsigned long nr_pages,
> struct zone *zone, struct memory_notify *arg)
> --
> 1.8.3.1
WARNING: multiple messages have this Message-ID (diff)
From: "Aneesh Kumar K.V" <aneesh.kumar-23VcF4HTsmIX0ybBhKVfKdBPR1lH4CV8@public.gmane.org>
To: Reza Arbab
<arbab-23VcF4HTsmIX0ybBhKVfKdBPR1lH4CV8@public.gmane.org>,
Michael Ellerman <mpe-Gsx/Oe8HsFggBc27wqDAHg@public.gmane.org>,
Benjamin Herrenschmidt
<benh-XVmvHMARGAS8U2dJNN8I7kB+6BGkLq7r@public.gmane.org>,
Paul Mackerras <paulus-eUNUBHrolfbYtjvyW6yDsg@public.gmane.org>,
Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Frank Rowand
<frowand.list-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
Andrew Morton
<akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org>
Cc: Bharata B Rao
<bharata-23VcF4HTsmIX0ybBhKVfKdBPR1lH4CV8@public.gmane.org>,
Nathan Fontenot
<nfont-23VcF4HTsmIX0ybBhKVfKdBPR1lH4CV8@public.gmane.org>,
Stewart Smith
<stewart-23VcF4HTsmIX0ybBhKVfKdBPR1lH4CV8@public.gmane.org>,
Alistair Popple <apopple-8fk3Idey6ehBDgjK7y7TUQ@public.gmane.org>,
Balbir Singh
<bsingharora-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
Tang Chen <tangchen-BthXqXjhjHXQFUHtdCDX3A@public.gmane.org>,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linuxppc-dev-uLR06cmDAlY/bJ5BZ2RsiQ@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-mm-Bw31MaZKKs3YtjvyW6yDsg@public.gmane.org
Subject: Re: [PATCH v4 4/5] mm: make processing of movable_node arch-specific
Date: Fri, 07 Oct 2016 12:07:11 +0530 [thread overview]
Message-ID: <87zimgmzqg.fsf@linux.vnet.ibm.com> (raw)
In-Reply-To: <1475778995-1420-5-git-send-email-arbab-23VcF4HTsmIX0ybBhKVfKdBPR1lH4CV8@public.gmane.org>
Reza Arbab <arbab-23VcF4HTsmIX0ybBhKVfKdBPR1lH4CV8@public.gmane.org> writes:
> Currently, CONFIG_MOVABLE_NODE depends on X86_64. In preparation to
> enable it for other arches, we need to factor a detail which is unique
> to x86 out of the generic mm code.
>
> Specifically, as documented in kernel-parameters.txt, the use of
> "movable_node" should remain restricted to x86:
>
> movable_node [KNL,X86] Boot-time switch to enable the effects
> of CONFIG_MOVABLE_NODE=y. See mm/Kconfig for details.
>
> This option tells x86 to find movable nodes identified by the ACPI SRAT.
> On other arches, it would have no benefit, only the undesired side
> effect of setting bottom-up memblock allocation.
>
> Since #ifdef CONFIG_MOVABLE_NODE will no longer be enough to restrict
> this option to x86, move it to an arch-specific compilation unit
> instead.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar-23VcF4HTsmIX0ybBhKVfKdBPR1lH4CV8@public.gmane.org>
>
> Signed-off-by: Reza Arbab <arbab-23VcF4HTsmIX0ybBhKVfKdBPR1lH4CV8@public.gmane.org>
> ---
> arch/x86/mm/numa.c | 35 ++++++++++++++++++++++++++++++++++-
> mm/memory_hotplug.c | 31 -------------------------------
> 2 files changed, 34 insertions(+), 32 deletions(-)
>
> diff --git a/arch/x86/mm/numa.c b/arch/x86/mm/numa.c
> index fb68210..e95cab4 100644
> --- a/arch/x86/mm/numa.c
> +++ b/arch/x86/mm/numa.c
> @@ -887,6 +887,38 @@ EXPORT_SYMBOL(cpumask_of_node);
> #endif /* !CONFIG_DEBUG_PER_CPU_MAPS */
>
> #ifdef CONFIG_MEMORY_HOTPLUG
> +
> +static int __init cmdline_parse_movable_node(char *p)
> +{
> +#ifdef CONFIG_MOVABLE_NODE
> + /*
> + * Memory used by the kernel cannot be hot-removed because Linux
> + * cannot migrate the kernel pages. When memory hotplug is
> + * enabled, we should prevent memblock from allocating memory
> + * for the kernel.
> + *
> + * ACPI SRAT records all hotpluggable memory ranges. But before
> + * SRAT is parsed, we don't know about it.
> + *
> + * The kernel image is loaded into memory at very early time. We
> + * cannot prevent this anyway. So on NUMA system, we set any
> + * node the kernel resides in as un-hotpluggable.
> + *
> + * Since on modern servers, one node could have double-digit
> + * gigabytes memory, we can assume the memory around the kernel
> + * image is also un-hotpluggable. So before SRAT is parsed, just
> + * allocate memory near the kernel image to try the best to keep
> + * the kernel away from hotpluggable memory.
> + */
> + memblock_set_bottom_up(true);
> + movable_node_enabled = true;
> +#else
> + pr_warn("movable_node option not supported\n");
> +#endif
> + return 0;
> +}
> +early_param("movable_node", cmdline_parse_movable_node);
> +
> int memory_add_physaddr_to_nid(u64 start)
> {
> struct numa_meminfo *mi = &numa_meminfo;
> @@ -899,4 +931,5 @@ int memory_add_physaddr_to_nid(u64 start)
> return nid;
> }
> EXPORT_SYMBOL_GPL(memory_add_physaddr_to_nid);
> -#endif
> +
> +#endif /* CONFIG_MEMORY_HOTPLUG */
> diff --git a/mm/memory_hotplug.c b/mm/memory_hotplug.c
> index 9d29ba0..79c709a 100644
> --- a/mm/memory_hotplug.c
> +++ b/mm/memory_hotplug.c
> @@ -1738,37 +1738,6 @@ static bool can_offline_normal(struct zone *zone, unsigned long nr_pages)
> }
> #endif /* CONFIG_MOVABLE_NODE */
>
> -static int __init cmdline_parse_movable_node(char *p)
> -{
> -#ifdef CONFIG_MOVABLE_NODE
> - /*
> - * Memory used by the kernel cannot be hot-removed because Linux
> - * cannot migrate the kernel pages. When memory hotplug is
> - * enabled, we should prevent memblock from allocating memory
> - * for the kernel.
> - *
> - * ACPI SRAT records all hotpluggable memory ranges. But before
> - * SRAT is parsed, we don't know about it.
> - *
> - * The kernel image is loaded into memory at very early time. We
> - * cannot prevent this anyway. So on NUMA system, we set any
> - * node the kernel resides in as un-hotpluggable.
> - *
> - * Since on modern servers, one node could have double-digit
> - * gigabytes memory, we can assume the memory around the kernel
> - * image is also un-hotpluggable. So before SRAT is parsed, just
> - * allocate memory near the kernel image to try the best to keep
> - * the kernel away from hotpluggable memory.
> - */
> - memblock_set_bottom_up(true);
> - movable_node_enabled = true;
> -#else
> - pr_warn("movable_node option not supported\n");
> -#endif
> - return 0;
> -}
> -early_param("movable_node", cmdline_parse_movable_node);
> -
> /* check which state of node_states will be changed when offline memory */
> static void node_states_check_changes_offline(unsigned long nr_pages,
> struct zone *zone, struct memory_notify *arg)
> --
> 1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
To: Reza Arbab <arbab@linux.vnet.ibm.com>,
Michael Ellerman <mpe@ellerman.id.au>,
Benjamin Herrenschmidt <benh@kernel.crashing.org>,
Paul Mackerras <paulus@samba.org>,
Rob Herring <robh+dt@kernel.org>,
Frank Rowand <frowand.list@gmail.com>,
Andrew Morton <akpm@linux-foundation.org>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>,
Nathan Fontenot <nfont@linux.vnet.ibm.com>,
Stewart Smith <stewart@linux.vnet.ibm.com>,
Alistair Popple <apopple@au1.ibm.com>,
Balbir Singh <bsingharora@gmail.com>,
Tang Chen <tangchen@cn.fujitsu.com>,
linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org,
devicetree@vger.kernel.org, linux-mm@kvack.org
Subject: Re: [PATCH v4 4/5] mm: make processing of movable_node arch-specific
Date: Fri, 07 Oct 2016 12:07:11 +0530 [thread overview]
Message-ID: <87zimgmzqg.fsf@linux.vnet.ibm.com> (raw)
In-Reply-To: <1475778995-1420-5-git-send-email-arbab@linux.vnet.ibm.com>
Reza Arbab <arbab@linux.vnet.ibm.com> writes:
> Currently, CONFIG_MOVABLE_NODE depends on X86_64. In preparation to
> enable it for other arches, we need to factor a detail which is unique
> to x86 out of the generic mm code.
>
> Specifically, as documented in kernel-parameters.txt, the use of
> "movable_node" should remain restricted to x86:
>
> movable_node [KNL,X86] Boot-time switch to enable the effects
> of CONFIG_MOVABLE_NODE=y. See mm/Kconfig for details.
>
> This option tells x86 to find movable nodes identified by the ACPI SRAT.
> On other arches, it would have no benefit, only the undesired side
> effect of setting bottom-up memblock allocation.
>
> Since #ifdef CONFIG_MOVABLE_NODE will no longer be enough to restrict
> this option to x86, move it to an arch-specific compilation unit
> instead.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
>
> Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com>
> ---
> arch/x86/mm/numa.c | 35 ++++++++++++++++++++++++++++++++++-
> mm/memory_hotplug.c | 31 -------------------------------
> 2 files changed, 34 insertions(+), 32 deletions(-)
>
> diff --git a/arch/x86/mm/numa.c b/arch/x86/mm/numa.c
> index fb68210..e95cab4 100644
> --- a/arch/x86/mm/numa.c
> +++ b/arch/x86/mm/numa.c
> @@ -887,6 +887,38 @@ EXPORT_SYMBOL(cpumask_of_node);
> #endif /* !CONFIG_DEBUG_PER_CPU_MAPS */
>
> #ifdef CONFIG_MEMORY_HOTPLUG
> +
> +static int __init cmdline_parse_movable_node(char *p)
> +{
> +#ifdef CONFIG_MOVABLE_NODE
> + /*
> + * Memory used by the kernel cannot be hot-removed because Linux
> + * cannot migrate the kernel pages. When memory hotplug is
> + * enabled, we should prevent memblock from allocating memory
> + * for the kernel.
> + *
> + * ACPI SRAT records all hotpluggable memory ranges. But before
> + * SRAT is parsed, we don't know about it.
> + *
> + * The kernel image is loaded into memory at very early time. We
> + * cannot prevent this anyway. So on NUMA system, we set any
> + * node the kernel resides in as un-hotpluggable.
> + *
> + * Since on modern servers, one node could have double-digit
> + * gigabytes memory, we can assume the memory around the kernel
> + * image is also un-hotpluggable. So before SRAT is parsed, just
> + * allocate memory near the kernel image to try the best to keep
> + * the kernel away from hotpluggable memory.
> + */
> + memblock_set_bottom_up(true);
> + movable_node_enabled = true;
> +#else
> + pr_warn("movable_node option not supported\n");
> +#endif
> + return 0;
> +}
> +early_param("movable_node", cmdline_parse_movable_node);
> +
> int memory_add_physaddr_to_nid(u64 start)
> {
> struct numa_meminfo *mi = &numa_meminfo;
> @@ -899,4 +931,5 @@ int memory_add_physaddr_to_nid(u64 start)
> return nid;
> }
> EXPORT_SYMBOL_GPL(memory_add_physaddr_to_nid);
> -#endif
> +
> +#endif /* CONFIG_MEMORY_HOTPLUG */
> diff --git a/mm/memory_hotplug.c b/mm/memory_hotplug.c
> index 9d29ba0..79c709a 100644
> --- a/mm/memory_hotplug.c
> +++ b/mm/memory_hotplug.c
> @@ -1738,37 +1738,6 @@ static bool can_offline_normal(struct zone *zone, unsigned long nr_pages)
> }
> #endif /* CONFIG_MOVABLE_NODE */
>
> -static int __init cmdline_parse_movable_node(char *p)
> -{
> -#ifdef CONFIG_MOVABLE_NODE
> - /*
> - * Memory used by the kernel cannot be hot-removed because Linux
> - * cannot migrate the kernel pages. When memory hotplug is
> - * enabled, we should prevent memblock from allocating memory
> - * for the kernel.
> - *
> - * ACPI SRAT records all hotpluggable memory ranges. But before
> - * SRAT is parsed, we don't know about it.
> - *
> - * The kernel image is loaded into memory at very early time. We
> - * cannot prevent this anyway. So on NUMA system, we set any
> - * node the kernel resides in as un-hotpluggable.
> - *
> - * Since on modern servers, one node could have double-digit
> - * gigabytes memory, we can assume the memory around the kernel
> - * image is also un-hotpluggable. So before SRAT is parsed, just
> - * allocate memory near the kernel image to try the best to keep
> - * the kernel away from hotpluggable memory.
> - */
> - memblock_set_bottom_up(true);
> - movable_node_enabled = true;
> -#else
> - pr_warn("movable_node option not supported\n");
> -#endif
> - return 0;
> -}
> -early_param("movable_node", cmdline_parse_movable_node);
> -
> /* check which state of node_states will be changed when offline memory */
> static void node_states_check_changes_offline(unsigned long nr_pages,
> struct zone *zone, struct memory_notify *arg)
> --
> 1.8.3.1
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>
next prev parent reply other threads:[~2016-10-07 6:37 UTC|newest]
Thread overview: 55+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-10-06 18:36 [PATCH v4 0/5] powerpc/mm: movable hotplug memory nodes Reza Arbab
2016-10-06 18:36 ` Reza Arbab
2016-10-06 18:36 ` [PATCH v4 1/5] drivers/of: introduce of_fdt_device_is_available() Reza Arbab
2016-10-06 18:36 ` Reza Arbab
2016-10-06 18:36 ` [PATCH v4 2/5] drivers/of: do not add memory for unavailable nodes Reza Arbab
2016-10-06 18:36 ` Reza Arbab
2016-10-11 13:58 ` Rob Herring
2016-10-11 13:58 ` Rob Herring
2016-10-21 6:22 ` Alistair Popple
2016-10-21 6:22 ` Alistair Popple
2016-10-23 1:51 ` Reza Arbab
2016-10-23 1:51 ` Reza Arbab
2016-10-24 10:24 ` Michael Ellerman
2016-10-24 10:24 ` Michael Ellerman
2016-10-24 18:20 ` Reza Arbab
2016-10-24 18:20 ` Reza Arbab
2016-10-24 18:20 ` Reza Arbab
2016-10-06 18:36 ` [PATCH v4 3/5] powerpc/mm: allow memory hotplug into a memoryless node Reza Arbab
2016-10-06 18:36 ` Reza Arbab
2016-10-20 3:30 ` Balbir Singh
2016-10-20 3:30 ` Balbir Singh
2016-10-20 3:30 ` Balbir Singh
2016-10-20 14:38 ` Reza Arbab
2016-10-20 14:38 ` Reza Arbab
2016-10-20 14:38 ` Reza Arbab
2016-10-25 9:39 ` Michael Ellerman
2016-10-25 9:39 ` Michael Ellerman
2016-10-06 18:36 ` [PATCH v4 4/5] mm: make processing of movable_node arch-specific Reza Arbab
2016-10-06 18:36 ` Reza Arbab
2016-10-06 18:36 ` Reza Arbab
2016-10-07 6:37 ` Aneesh Kumar K.V [this message]
2016-10-07 6:37 ` Aneesh Kumar K.V
2016-10-07 6:37 ` Aneesh Kumar K.V
2016-10-11 12:26 ` Balbir Singh
2016-10-11 12:26 ` Balbir Singh
2016-10-25 12:15 ` Balbir Singh
2016-10-25 12:15 ` Balbir Singh
2016-10-25 15:55 ` Reza Arbab
2016-10-25 15:55 ` Reza Arbab
2016-10-25 22:34 ` Balbir Singh
2016-10-25 22:34 ` Balbir Singh
2016-10-26 0:49 ` Reza Arbab
2016-10-26 0:49 ` Reza Arbab
2016-10-26 10:52 ` Michael Ellerman
2016-10-26 10:52 ` Michael Ellerman
2016-10-26 17:03 ` Reza Arbab
2016-10-26 17:03 ` Reza Arbab
2016-10-25 22:59 ` Balbir Singh
2016-10-25 22:59 ` Balbir Singh
2016-10-06 18:36 ` [PATCH v4 5/5] mm: enable CONFIG_MOVABLE_NODE on non-x86 arches Reza Arbab
2016-10-06 18:36 ` Reza Arbab
2016-10-07 6:40 ` Aneesh Kumar K.V
2016-10-07 6:40 ` Aneesh Kumar K.V
2016-10-11 13:17 ` Balbir Singh
2016-10-11 13:17 ` Balbir Singh
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87zimgmzqg.fsf@linux.vnet.ibm.com \
--to=aneesh.kumar@linux.vnet.ibm.com \
--cc=akpm@linux-foundation.org \
--cc=apopple@au1.ibm.com \
--cc=arbab@linux.vnet.ibm.com \
--cc=benh@kernel.crashing.org \
--cc=bharata@linux.vnet.ibm.com \
--cc=bsingharora@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=frowand.list@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mm@kvack.org \
--cc=linuxppc-dev@lists.ozlabs.org \
--cc=mpe@ellerman.id.au \
--cc=nfont@linux.vnet.ibm.com \
--cc=paulus@samba.org \
--cc=robh+dt@kernel.org \
--cc=stewart@linux.vnet.ibm.com \
--cc=tangchen@cn.fujitsu.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.