[PATCH net-next 00/11] net: stmmac: mdio cleanups

[PATCH net-next 00/11] net: stmmac: mdio cleanups

[Russell King (Oracle)]

Hi,

Clean up the stmmac MDIO code:
- provide an address register formatter to avoid repeated code
- provide a common function to wait for the busy bit to clear
- pre-compute the CR field (mdio clock divider)
- move address formatter into read/write functions
- combine the read/write functions into a common accessor function
- move runtime PM handling into common accessor function
- rename register constants to better reflect manufacturer names
- move stmmac_clk_csr_set() into stmmac_mdio
- make stmmac_clk_csr_set() return the CR field value and remove
  priv->clk_csr
- clean up if() range tests in stmmac_clk_csr_set()
- use STMMAC_CSR_xxx definitions in initialisers

 drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c  |   5 +-
 .../net/ethernet/stmicro/stmmac/dwmac-loongson.c   |   3 +-
 drivers/net/ethernet/stmicro/stmmac/stmmac.h       |   2 +-
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c  |  82 -----
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c  | 342 ++++++++++++---------
 drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c   |   5 +-
 6 files changed, 204 insertions(+), 235 deletions(-)

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

[PATCH net-next 01/11] net: stmmac: mdio: provide address register formatter

[Russell King (Oracle)]

Rather than duplicating the logic for filling the PA (MDIO address),
GR (MDIO register/devad), CR (clock range) and GB (busy) fields of the
address register in four locations, provide a helper to do this.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 53 +++++++++----------
 1 file changed, 26 insertions(+), 27 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 0a302b711bc2..3106fef6eed8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -229,6 +229,24 @@ static int stmmac_xgmac2_mdio_write_c45(struct mii_bus *bus, int phyaddr,
 					phydata);
 }
 
+/**
+ * stmmac_mdio_format_addr() - format the address register
+ * @priv: struct stmmac_priv pointer
+ * @pa: 5-bit MDIO package address
+ * @gr: 5-bit MDIO register address (C22) or MDIO device address (C45)
+ */
+static u32 stmmac_mdio_format_addr(struct stmmac_priv *priv,
+				   unsigned int pa, unsigned int gr)
+{
+	const struct mii_regs *mii_regs = &priv->hw->mii;
+
+	return ((pa << mii_regs->addr_shift) & mii_regs->addr_mask) |
+	       ((gr << mii_regs->reg_shift) & mii_regs->reg_mask) |
+	       ((priv->clk_csr << mii_regs->clk_csr_shift) &
+		mii_regs->clk_csr_mask) |
+	       MII_BUSY;
+}
+
 static int stmmac_mdio_read(struct stmmac_priv *priv, int data, u32 value)
 {
 	unsigned int mii_address = priv->hw->mii.addr;
@@ -263,18 +281,14 @@ static int stmmac_mdio_read(struct stmmac_priv *priv, int data, u32 value)
 static int stmmac_mdio_read_c22(struct mii_bus *bus, int phyaddr, int phyreg)
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
-	u32 value = MII_BUSY;
 	int data = 0;
+	u32 value;
 
 	data = pm_runtime_resume_and_get(priv->device);
 	if (data < 0)
 		return data;
 
-	value |= (phyaddr << priv->hw->mii.addr_shift)
-		& priv->hw->mii.addr_mask;
-	value |= (phyreg << priv->hw->mii.reg_shift) & priv->hw->mii.reg_mask;
-	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
-		& priv->hw->mii.clk_csr_mask;
+	value = stmmac_mdio_format_addr(priv, phyaddr, phyreg);
 	if (priv->plat->has_gmac4)
 		value |= MII_GMAC4_READ;
 
@@ -300,20 +314,16 @@ static int stmmac_mdio_read_c45(struct mii_bus *bus, int phyaddr, int devad,
 				int phyreg)
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
-	u32 value = MII_BUSY;
 	int data = 0;
+	u32 value;
 
 	data = pm_runtime_resume_and_get(priv->device);
 	if (data < 0)
 		return data;
 
-	value |= (phyaddr << priv->hw->mii.addr_shift)
-		& priv->hw->mii.addr_mask;
-	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
-		& priv->hw->mii.clk_csr_mask;
+	value = stmmac_mdio_format_addr(priv, phyaddr, devad);
 	value |= MII_GMAC4_READ;
 	value |= MII_GMAC4_C45E;
-	value |= (devad << priv->hw->mii.reg_shift) & priv->hw->mii.reg_mask;
 
 	data |= phyreg << MII_GMAC4_REG_ADDR_SHIFT;
 
@@ -357,18 +367,13 @@ static int stmmac_mdio_write_c22(struct mii_bus *bus, int phyaddr, int phyreg,
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
 	int ret, data = phydata;
-	u32 value = MII_BUSY;
+	u32 value;
 
 	ret = pm_runtime_resume_and_get(priv->device);
 	if (ret < 0)
 		return ret;
 
-	value |= (phyaddr << priv->hw->mii.addr_shift)
-		& priv->hw->mii.addr_mask;
-	value |= (phyreg << priv->hw->mii.reg_shift) & priv->hw->mii.reg_mask;
-
-	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
-		& priv->hw->mii.clk_csr_mask;
+	value = stmmac_mdio_format_addr(priv, phyaddr, phyreg);
 	if (priv->plat->has_gmac4)
 		value |= MII_GMAC4_WRITE;
 	else
@@ -395,21 +400,15 @@ static int stmmac_mdio_write_c45(struct mii_bus *bus, int phyaddr,
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
 	int ret, data = phydata;
-	u32 value = MII_BUSY;
+	u32 value;
 
 	ret = pm_runtime_resume_and_get(priv->device);
 	if (ret < 0)
 		return ret;
 
-	value |= (phyaddr << priv->hw->mii.addr_shift)
-		& priv->hw->mii.addr_mask;
-
-	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
-		& priv->hw->mii.clk_csr_mask;
-
+	value = stmmac_mdio_format_addr(priv, phyaddr, devad);
 	value |= MII_GMAC4_WRITE;
 	value |= MII_GMAC4_C45E;
-	value |= (devad << priv->hw->mii.reg_shift) & priv->hw->mii.reg_mask;
 
 	data |= phyreg << MII_GMAC4_REG_ADDR_SHIFT;
 
-- 
2.47.2

Re: [PATCH net-next 01/11] net: stmmac: mdio: provide address register formatter

[Jakub Kicinski]

On Wed, 03 Sep 2025 13:39:18 +0100 Russell King (Oracle) wrote:
> +/**
> + * stmmac_mdio_format_addr() - format the address register
> + * @priv: struct stmmac_priv pointer
> + * @pa: 5-bit MDIO package address
> + * @gr: 5-bit MDIO register address (C22) or MDIO device address (C45)

If you're willing to oblige kdoc it wants Return: to be documented.
Similar comment on patch 9 where stmmac_clk_csr_set() gains a return
value.

[PATCH net-next 02/11] net: stmmac: mdio: provide stmmac_mdio_wait()

[Russell King (Oracle)]

All the readl_poll_timeout()s follow the same pattern - test a register
for a bit being clear every 100us, and timeout after 10ms returning
-EBUSY. Wrap this up into a function to avoid duplicating this.

This slightly changes the return value for stmmac_mdio_write() if the
second readl_poll_timeout() fails - rather than returning -ETIMEDOUT
we return -EBUSY matching the stmmac_mdio_read() behaviour.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 70 +++++++++----------
 1 file changed, 33 insertions(+), 37 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 3106fef6eed8..7887340ae7b6 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -45,6 +45,16 @@
 #define MII_XGMAC_PA_SHIFT		16
 #define MII_XGMAC_DA_SHIFT		21
 
+static int stmmac_mdio_wait(void __iomem *reg, u32 mask)
+{
+	u32 v;
+
+	if (readl_poll_timeout(reg, v, !(v & mask), 100, 10000))
+		return -EBUSY;
+
+	return 0;
+}
+
 static void stmmac_xgmac2_c45_format(struct stmmac_priv *priv, int phyaddr,
 				     int devad, int phyreg, u32 *hw_addr)
 {
@@ -83,7 +93,6 @@ static int stmmac_xgmac2_mdio_read(struct stmmac_priv *priv, u32 addr,
 {
 	unsigned int mii_address = priv->hw->mii.addr;
 	unsigned int mii_data = priv->hw->mii.data;
-	u32 tmp;
 	int ret;
 
 	ret = pm_runtime_resume_and_get(priv->device);
@@ -91,33 +100,27 @@ static int stmmac_xgmac2_mdio_read(struct stmmac_priv *priv, u32 addr,
 		return ret;
 
 	/* Wait until any existing MII operation is complete */
-	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
-			       !(tmp & MII_XGMAC_BUSY), 100, 10000)) {
-		ret = -EBUSY;
+	ret = stmmac_mdio_wait(priv->ioaddr + mii_data, MII_XGMAC_BUSY);
+	if (ret)
 		goto err_disable_clks;
-	}
 
 	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
 		& priv->hw->mii.clk_csr_mask;
 	value |= MII_XGMAC_READ;
 
 	/* Wait until any existing MII operation is complete */
-	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
-			       !(tmp & MII_XGMAC_BUSY), 100, 10000)) {
-		ret = -EBUSY;
+	ret = stmmac_mdio_wait(priv->ioaddr + mii_data, MII_XGMAC_BUSY);
+	if (ret)
 		goto err_disable_clks;
-	}
 
 	/* Set the MII address register to read */
 	writel(addr, priv->ioaddr + mii_address);
 	writel(value, priv->ioaddr + mii_data);
 
 	/* Wait until any existing MII operation is complete */
-	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
-			       !(tmp & MII_XGMAC_BUSY), 100, 10000)) {
-		ret = -EBUSY;
+	ret = stmmac_mdio_wait(priv->ioaddr + mii_data, MII_XGMAC_BUSY);
+	if (ret)
 		goto err_disable_clks;
-	}
 
 	/* Read the data from the MII data register */
 	ret = (int)readl(priv->ioaddr + mii_data) & GENMASK(15, 0);
@@ -160,7 +163,6 @@ static int stmmac_xgmac2_mdio_write(struct stmmac_priv *priv, u32 addr,
 {
 	unsigned int mii_address = priv->hw->mii.addr;
 	unsigned int mii_data = priv->hw->mii.data;
-	u32 tmp;
 	int ret;
 
 	ret = pm_runtime_resume_and_get(priv->device);
@@ -168,11 +170,9 @@ static int stmmac_xgmac2_mdio_write(struct stmmac_priv *priv, u32 addr,
 		return ret;
 
 	/* Wait until any existing MII operation is complete */
-	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
-			       !(tmp & MII_XGMAC_BUSY), 100, 10000)) {
-		ret = -EBUSY;
+	ret = stmmac_mdio_wait(priv->ioaddr + mii_data, MII_XGMAC_BUSY);
+	if (ret)
 		goto err_disable_clks;
-	}
 
 	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
 		& priv->hw->mii.clk_csr_mask;
@@ -180,19 +180,16 @@ static int stmmac_xgmac2_mdio_write(struct stmmac_priv *priv, u32 addr,
 	value |= MII_XGMAC_WRITE;
 
 	/* Wait until any existing MII operation is complete */
-	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
-			       !(tmp & MII_XGMAC_BUSY), 100, 10000)) {
-		ret = -EBUSY;
+	ret = stmmac_mdio_wait(priv->ioaddr + mii_data, MII_XGMAC_BUSY);
+	if (ret)
 		goto err_disable_clks;
-	}
 
 	/* Set the MII address register to write */
 	writel(addr, priv->ioaddr + mii_address);
 	writel(value, priv->ioaddr + mii_data);
 
 	/* Wait until any existing MII operation is complete */
-	ret = readl_poll_timeout(priv->ioaddr + mii_data, tmp,
-				 !(tmp & MII_XGMAC_BUSY), 100, 10000);
+	ret = stmmac_mdio_wait(priv->ioaddr + mii_data, MII_XGMAC_BUSY);
 
 err_disable_clks:
 	pm_runtime_put(priv->device);
@@ -251,18 +248,18 @@ static int stmmac_mdio_read(struct stmmac_priv *priv, int data, u32 value)
 {
 	unsigned int mii_address = priv->hw->mii.addr;
 	unsigned int mii_data = priv->hw->mii.data;
-	u32 v;
+	int ret;
 
-	if (readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY),
-			       100, 10000))
-		return -EBUSY;
+	ret = stmmac_mdio_wait(priv->ioaddr + mii_address, MII_BUSY);
+	if (ret)
+		return ret;
 
 	writel(data, priv->ioaddr + mii_data);
 	writel(value, priv->ioaddr + mii_address);
 
-	if (readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY),
-			       100, 10000))
-		return -EBUSY;
+	ret = stmmac_mdio_wait(priv->ioaddr + mii_address, MII_BUSY);
+	if (ret)
+		return ret;
 
 	/* Read the data from the MII data register */
 	return readl(priv->ioaddr + mii_data) & MII_DATA_MASK;
@@ -338,20 +335,19 @@ static int stmmac_mdio_write(struct stmmac_priv *priv, int data, u32 value)
 {
 	unsigned int mii_address = priv->hw->mii.addr;
 	unsigned int mii_data = priv->hw->mii.data;
-	u32 v;
+	int ret;
 
 	/* Wait until any existing MII operation is complete */
-	if (readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY),
-			       100, 10000))
-		return -EBUSY;
+	ret = stmmac_mdio_wait(priv->ioaddr + mii_address, MII_BUSY);
+	if (ret)
+		return ret;
 
 	/* Set the MII address register to write */
 	writel(data, priv->ioaddr + mii_data);
 	writel(value, priv->ioaddr + mii_address);
 
 	/* Wait until any existing MII operation is complete */
-	return readl_poll_timeout(priv->ioaddr + mii_address, v,
-				  !(v & MII_BUSY), 100, 10000);
+	return stmmac_mdio_wait(priv->ioaddr + mii_address, MII_BUSY);
 }
 
 /**
-- 
2.47.2

[PATCH net-next 03/11] net: stmmac: mdio: provide priv->gmii_address_bus_config

[Russell King (Oracle)]

Provide a pre-formatted value for the MDIO address register fields
which remain constant across the various different transactions
rather than recreating the register value from scratch every time.
Currently, we only do this for the CR (clock range) field.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac.h  |  1 +
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 26 ++++++++++++-------
 2 files changed, 18 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index 78d6b3737a26..4d5577935b13 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -290,6 +290,7 @@ struct stmmac_priv {
 	int wolopts;
 	int wol_irq;
 	int clk_csr;
+	u32 gmii_address_bus_config;
 	struct timer_list eee_ctrl_timer;
 	int lpi_irq;
 	u32 tx_lpi_timer;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 7887340ae7b6..2267a93ce44d 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -104,9 +104,7 @@ static int stmmac_xgmac2_mdio_read(struct stmmac_priv *priv, u32 addr,
 	if (ret)
 		goto err_disable_clks;
 
-	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
-		& priv->hw->mii.clk_csr_mask;
-	value |= MII_XGMAC_READ;
+	value |= priv->gmii_address_bus_config | MII_XGMAC_READ;
 
 	/* Wait until any existing MII operation is complete */
 	ret = stmmac_mdio_wait(priv->ioaddr + mii_data, MII_XGMAC_BUSY);
@@ -174,10 +172,7 @@ static int stmmac_xgmac2_mdio_write(struct stmmac_priv *priv, u32 addr,
 	if (ret)
 		goto err_disable_clks;
 
-	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
-		& priv->hw->mii.clk_csr_mask;
-	value |= phydata;
-	value |= MII_XGMAC_WRITE;
+	value |= priv->gmii_address_bus_config | phydata | MII_XGMAC_WRITE;
 
 	/* Wait until any existing MII operation is complete */
 	ret = stmmac_mdio_wait(priv->ioaddr + mii_data, MII_XGMAC_BUSY);
@@ -239,8 +234,7 @@ static u32 stmmac_mdio_format_addr(struct stmmac_priv *priv,
 
 	return ((pa << mii_regs->addr_shift) & mii_regs->addr_mask) |
 	       ((gr << mii_regs->reg_shift) & mii_regs->reg_mask) |
-	       ((priv->clk_csr << mii_regs->clk_csr_shift) &
-		mii_regs->clk_csr_mask) |
+	       priv->gmii_address_bus_config |
 	       MII_BUSY;
 }
 
@@ -515,6 +509,18 @@ void stmmac_pcs_clean(struct net_device *ndev)
 	priv->hw->xpcs = NULL;
 }
 
+static void stmmac_mdio_bus_config(struct stmmac_priv *priv, u32 value)
+{
+	value <<= priv->hw->mii.clk_csr_shift;
+
+	if (value & ~priv->hw->mii.clk_csr_mask)
+		dev_warn(priv->device,
+			 "clk_csr value out of range (0x%08x exceeds mask 0x%08x), truncating\n",
+			 value, priv->hw->mii.clk_csr_mask);
+
+	priv->gmii_address_bus_config = value & priv->hw->mii.clk_csr_mask;
+}
+
 /**
  * stmmac_mdio_register
  * @ndev: net device structure
@@ -535,6 +541,8 @@ int stmmac_mdio_register(struct net_device *ndev)
 	if (!mdio_bus_data)
 		return 0;
 
+	stmmac_mdio_bus_config(priv, priv->clk_csr);
+
 	new_bus = mdiobus_alloc();
 	if (!new_bus)
 		return -ENOMEM;
-- 
2.47.2

[PATCH net-next 04/11] net: stmmac: mdio: move stmmac_mdio_format_addr() into read/write

[Russell King (Oracle)]

Move stmmac_mdio_format_addr() into stmmac_mdio_read() and
stmmac_mdio_write().

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 46 ++++++++++---------
 1 file changed, 25 insertions(+), 21 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 2267a93ce44d..dafe97a49d1f 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -238,16 +238,20 @@ static u32 stmmac_mdio_format_addr(struct stmmac_priv *priv,
 	       MII_BUSY;
 }
 
-static int stmmac_mdio_read(struct stmmac_priv *priv, int data, u32 value)
+static int stmmac_mdio_read(struct stmmac_priv *priv, unsigned int pa,
+			    unsigned int gr, u32 cmd, int data)
 {
 	unsigned int mii_address = priv->hw->mii.addr;
 	unsigned int mii_data = priv->hw->mii.data;
+	u32 value;
 	int ret;
 
 	ret = stmmac_mdio_wait(priv->ioaddr + mii_address, MII_BUSY);
 	if (ret)
 		return ret;
 
+	value = stmmac_mdio_format_addr(priv, pa, gr) | cmd;
+
 	writel(data, priv->ioaddr + mii_data);
 	writel(value, priv->ioaddr + mii_address);
 
@@ -273,17 +277,18 @@ static int stmmac_mdio_read_c22(struct mii_bus *bus, int phyaddr, int phyreg)
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
 	int data = 0;
-	u32 value;
+	u32 cmd;
 
 	data = pm_runtime_resume_and_get(priv->device);
 	if (data < 0)
 		return data;
 
-	value = stmmac_mdio_format_addr(priv, phyaddr, phyreg);
 	if (priv->plat->has_gmac4)
-		value |= MII_GMAC4_READ;
+		cmd = MII_GMAC4_READ;
+	else
+		cmd = 0;
 
-	data = stmmac_mdio_read(priv, data, value);
+	data = stmmac_mdio_read(priv, phyaddr, phyreg, cmd, data);
 
 	pm_runtime_put(priv->device);
 
@@ -306,29 +311,29 @@ static int stmmac_mdio_read_c45(struct mii_bus *bus, int phyaddr, int devad,
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
 	int data = 0;
-	u32 value;
+	u32 cmd;
 
 	data = pm_runtime_resume_and_get(priv->device);
 	if (data < 0)
 		return data;
 
-	value = stmmac_mdio_format_addr(priv, phyaddr, devad);
-	value |= MII_GMAC4_READ;
-	value |= MII_GMAC4_C45E;
+	cmd = MII_GMAC4_READ | MII_GMAC4_C45E;
 
 	data |= phyreg << MII_GMAC4_REG_ADDR_SHIFT;
 
-	data = stmmac_mdio_read(priv, data, value);
+	data = stmmac_mdio_read(priv, phyaddr, devad, cmd, data);
 
 	pm_runtime_put(priv->device);
 
 	return data;
 }
 
-static int stmmac_mdio_write(struct stmmac_priv *priv, int data, u32 value)
+static int stmmac_mdio_write(struct stmmac_priv *priv, unsigned int pa,
+			     unsigned int gr, u32 cmd, int data)
 {
 	unsigned int mii_address = priv->hw->mii.addr;
 	unsigned int mii_data = priv->hw->mii.data;
+	u32 value;
 	int ret;
 
 	/* Wait until any existing MII operation is complete */
@@ -336,6 +341,8 @@ static int stmmac_mdio_write(struct stmmac_priv *priv, int data, u32 value)
 	if (ret)
 		return ret;
 
+	value = stmmac_mdio_format_addr(priv, pa, gr) | cmd;
+
 	/* Set the MII address register to write */
 	writel(data, priv->ioaddr + mii_data);
 	writel(value, priv->ioaddr + mii_address);
@@ -357,19 +364,18 @@ static int stmmac_mdio_write_c22(struct mii_bus *bus, int phyaddr, int phyreg,
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
 	int ret, data = phydata;
-	u32 value;
+	u32 cmd;
 
 	ret = pm_runtime_resume_and_get(priv->device);
 	if (ret < 0)
 		return ret;
 
-	value = stmmac_mdio_format_addr(priv, phyaddr, phyreg);
 	if (priv->plat->has_gmac4)
-		value |= MII_GMAC4_WRITE;
+		cmd = MII_GMAC4_WRITE;
 	else
-		value |= MII_WRITE;
+		cmd = MII_WRITE;
 
-	ret = stmmac_mdio_write(priv, data, value);
+	ret = stmmac_mdio_write(priv, phyaddr, phyreg, cmd, data);
 
 	pm_runtime_put(priv->device);
 
@@ -390,19 +396,17 @@ static int stmmac_mdio_write_c45(struct mii_bus *bus, int phyaddr,
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
 	int ret, data = phydata;
-	u32 value;
+	u32 cmd;
 
 	ret = pm_runtime_resume_and_get(priv->device);
 	if (ret < 0)
 		return ret;
 
-	value = stmmac_mdio_format_addr(priv, phyaddr, devad);
-	value |= MII_GMAC4_WRITE;
-	value |= MII_GMAC4_C45E;
+	cmd = MII_GMAC4_WRITE | MII_GMAC4_C45E;
 
 	data |= phyreg << MII_GMAC4_REG_ADDR_SHIFT;
 
-	ret = stmmac_mdio_write(priv, data, value);
+	ret = stmmac_mdio_write(priv, phyaddr, devad, cmd, data);
 
 	pm_runtime_put(priv->device);
 
-- 
2.47.2

[PATCH net-next 05/11] net: stmmac: mdio: merge stmmac_mdio_read() and stmmac_mdio_write()

[Russell King (Oracle)]

stmmac_mdio_read() and stmmac_mdio_write() are virtually identical
except for the final read in the stmmac_mdio_read(). Handle this as
a flag.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 59 ++++++++-----------
 1 file changed, 24 insertions(+), 35 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index dafe97a49d1f..62e74467de49 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -238,29 +238,41 @@ static u32 stmmac_mdio_format_addr(struct stmmac_priv *priv,
 	       MII_BUSY;
 }
 
-static int stmmac_mdio_read(struct stmmac_priv *priv, unsigned int pa,
-			    unsigned int gr, u32 cmd, int data)
+static int stmmac_mdio_access(struct stmmac_priv *priv, unsigned int pa,
+			      unsigned int gr, u32 cmd, u32 data, bool read)
 {
-	unsigned int mii_address = priv->hw->mii.addr;
-	unsigned int mii_data = priv->hw->mii.data;
-	u32 value;
+	void __iomem *mii_address = priv->ioaddr + priv->hw->mii.addr;
+	void __iomem *mii_data = priv->ioaddr + priv->hw->mii.data;
+	u32 addr;
 	int ret;
 
-	ret = stmmac_mdio_wait(priv->ioaddr + mii_address, MII_BUSY);
+	ret = stmmac_mdio_wait(mii_address, MII_BUSY);
 	if (ret)
 		return ret;
 
-	value = stmmac_mdio_format_addr(priv, pa, gr) | cmd;
+	addr = stmmac_mdio_format_addr(priv, pa, gr) | cmd;
 
-	writel(data, priv->ioaddr + mii_data);
-	writel(value, priv->ioaddr + mii_address);
+	writel(data, mii_data);
+	writel(addr, mii_address);
 
-	ret = stmmac_mdio_wait(priv->ioaddr + mii_address, MII_BUSY);
+	ret = stmmac_mdio_wait(mii_address, MII_BUSY);
 	if (ret)
 		return ret;
 
-	/* Read the data from the MII data register */
-	return readl(priv->ioaddr + mii_data) & MII_DATA_MASK;
+	/* Read the data from the MII data register if in read mode */
+	return read ? readl(mii_data) & MII_DATA_MASK : 0;
+}
+
+static int stmmac_mdio_read(struct stmmac_priv *priv, unsigned int pa,
+			    unsigned int gr, u32 cmd, int data)
+{
+	return stmmac_mdio_access(priv, pa, gr, cmd, data, true);
+}
+
+static int stmmac_mdio_write(struct stmmac_priv *priv, unsigned int pa,
+			     unsigned int gr, u32 cmd, int data)
+{
+	return stmmac_mdio_access(priv, pa, gr, cmd, data, false);
 }
 
 /**
@@ -328,29 +340,6 @@ static int stmmac_mdio_read_c45(struct mii_bus *bus, int phyaddr, int devad,
 	return data;
 }
 
-static int stmmac_mdio_write(struct stmmac_priv *priv, unsigned int pa,
-			     unsigned int gr, u32 cmd, int data)
-{
-	unsigned int mii_address = priv->hw->mii.addr;
-	unsigned int mii_data = priv->hw->mii.data;
-	u32 value;
-	int ret;
-
-	/* Wait until any existing MII operation is complete */
-	ret = stmmac_mdio_wait(priv->ioaddr + mii_address, MII_BUSY);
-	if (ret)
-		return ret;
-
-	value = stmmac_mdio_format_addr(priv, pa, gr) | cmd;
-
-	/* Set the MII address register to write */
-	writel(data, priv->ioaddr + mii_data);
-	writel(value, priv->ioaddr + mii_address);
-
-	/* Wait until any existing MII operation is complete */
-	return stmmac_mdio_wait(priv->ioaddr + mii_address, MII_BUSY);
-}
-
 /**
  * stmmac_mdio_write_c22
  * @bus: points to the mii_bus structure
-- 
2.47.2

[PATCH net-next 06/11] net: stmmac: mdio: move runtime PM into stmmac_mdio_access()

[Russell King (Oracle)]

Move the runtime PM handling into the common stmmac_mdio_access()
function, rather than having it in the four top-level bus access
functions.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 71 ++++++-------------
 1 file changed, 20 insertions(+), 51 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 62e74467de49..2d6a5d40e2c1 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -246,9 +246,13 @@ static int stmmac_mdio_access(struct stmmac_priv *priv, unsigned int pa,
 	u32 addr;
 	int ret;
 
+	ret = pm_runtime_resume_and_get(priv->device);
+	if (ret < 0)
+		return ret;
+
 	ret = stmmac_mdio_wait(mii_address, MII_BUSY);
 	if (ret)
-		return ret;
+		goto out;
 
 	addr = stmmac_mdio_format_addr(priv, pa, gr) | cmd;
 
@@ -257,10 +261,15 @@ static int stmmac_mdio_access(struct stmmac_priv *priv, unsigned int pa,
 
 	ret = stmmac_mdio_wait(mii_address, MII_BUSY);
 	if (ret)
-		return ret;
+		goto out;
 
 	/* Read the data from the MII data register if in read mode */
-	return read ? readl(mii_data) & MII_DATA_MASK : 0;
+	ret = read ? readl(mii_data) & MII_DATA_MASK : 0;
+
+out:
+	pm_runtime_put(priv->device);
+
+	return ret;
 }
 
 static int stmmac_mdio_read(struct stmmac_priv *priv, unsigned int pa,
@@ -288,23 +297,14 @@ static int stmmac_mdio_write(struct stmmac_priv *priv, unsigned int pa,
 static int stmmac_mdio_read_c22(struct mii_bus *bus, int phyaddr, int phyreg)
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
-	int data = 0;
 	u32 cmd;
 
-	data = pm_runtime_resume_and_get(priv->device);
-	if (data < 0)
-		return data;
-
 	if (priv->plat->has_gmac4)
 		cmd = MII_GMAC4_READ;
 	else
 		cmd = 0;
 
-	data = stmmac_mdio_read(priv, phyaddr, phyreg, cmd, data);
-
-	pm_runtime_put(priv->device);
-
-	return data;
+	return stmmac_mdio_read(priv, phyaddr, phyreg, cmd, 0);
 }
 
 /**
@@ -322,22 +322,10 @@ static int stmmac_mdio_read_c45(struct mii_bus *bus, int phyaddr, int devad,
 				int phyreg)
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
-	int data = 0;
-	u32 cmd;
-
-	data = pm_runtime_resume_and_get(priv->device);
-	if (data < 0)
-		return data;
-
-	cmd = MII_GMAC4_READ | MII_GMAC4_C45E;
-
-	data |= phyreg << MII_GMAC4_REG_ADDR_SHIFT;
-
-	data = stmmac_mdio_read(priv, phyaddr, devad, cmd, data);
+	int data = phyreg << MII_GMAC4_REG_ADDR_SHIFT;
+	u32 cmd = MII_GMAC4_READ | MII_GMAC4_C45E;
 
-	pm_runtime_put(priv->device);
-
-	return data;
+	return stmmac_mdio_read(priv, phyaddr, devad, cmd, data);
 }
 
 /**
@@ -352,23 +340,14 @@ static int stmmac_mdio_write_c22(struct mii_bus *bus, int phyaddr, int phyreg,
 				 u16 phydata)
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
-	int ret, data = phydata;
 	u32 cmd;
 
-	ret = pm_runtime_resume_and_get(priv->device);
-	if (ret < 0)
-		return ret;
-
 	if (priv->plat->has_gmac4)
 		cmd = MII_GMAC4_WRITE;
 	else
 		cmd = MII_WRITE;
 
-	ret = stmmac_mdio_write(priv, phyaddr, phyreg, cmd, data);
-
-	pm_runtime_put(priv->device);
-
-	return ret;
+	return stmmac_mdio_write(priv, phyaddr, phyreg, cmd, phydata);
 }
 
 /**
@@ -384,22 +363,12 @@ static int stmmac_mdio_write_c45(struct mii_bus *bus, int phyaddr,
 				 int devad, int phyreg, u16 phydata)
 {
 	struct stmmac_priv *priv = netdev_priv(bus->priv);
-	int ret, data = phydata;
-	u32 cmd;
-
-	ret = pm_runtime_resume_and_get(priv->device);
-	if (ret < 0)
-		return ret;
-
-	cmd = MII_GMAC4_WRITE | MII_GMAC4_C45E;
+	u32 cmd = MII_GMAC4_WRITE | MII_GMAC4_C45E;
+	int data = phydata;
 
 	data |= phyreg << MII_GMAC4_REG_ADDR_SHIFT;
 
-	ret = stmmac_mdio_write(priv, phyaddr, devad, cmd, data);
-
-	pm_runtime_put(priv->device);
-
-	return ret;
+	return stmmac_mdio_write(priv, phyaddr, devad, cmd, data);
 }
 
 /**
-- 
2.47.2

[PATCH net-next 07/11] net: stmmac: mdio: improve mdio register field definitions

[Russell King (Oracle)]

Include the register name in the definitions, and use a name which
more closely resembles that used in documentation, while still being
descriptive.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c    | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 2d6a5d40e2c1..4d0de3c269a8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -23,9 +23,9 @@
 #include "dwxgmac2.h"
 #include "stmmac.h"
 
-#define MII_BUSY 0x00000001
-#define MII_WRITE 0x00000002
-#define MII_DATA_MASK GENMASK(15, 0)
+#define MII_ADDR_GBUSY			BIT(0)
+#define MII_ADDR_GWRITE			BIT(1)
+#define MII_DATA_GD_MASK		GENMASK(15, 0)
 
 /* GMAC4 defines */
 #define MII_GMAC4_GOC_SHIFT		2
@@ -235,7 +235,7 @@ static u32 stmmac_mdio_format_addr(struct stmmac_priv *priv,
 	return ((pa << mii_regs->addr_shift) & mii_regs->addr_mask) |
 	       ((gr << mii_regs->reg_shift) & mii_regs->reg_mask) |
 	       priv->gmii_address_bus_config |
-	       MII_BUSY;
+	       MII_ADDR_GBUSY;
 }
 
 static int stmmac_mdio_access(struct stmmac_priv *priv, unsigned int pa,
@@ -250,7 +250,7 @@ static int stmmac_mdio_access(struct stmmac_priv *priv, unsigned int pa,
 	if (ret < 0)
 		return ret;
 
-	ret = stmmac_mdio_wait(mii_address, MII_BUSY);
+	ret = stmmac_mdio_wait(mii_address, MII_ADDR_GBUSY);
 	if (ret)
 		goto out;
 
@@ -259,12 +259,12 @@ static int stmmac_mdio_access(struct stmmac_priv *priv, unsigned int pa,
 	writel(data, mii_data);
 	writel(addr, mii_address);
 
-	ret = stmmac_mdio_wait(mii_address, MII_BUSY);
+	ret = stmmac_mdio_wait(mii_address, MII_ADDR_GBUSY);
 	if (ret)
 		goto out;
 
 	/* Read the data from the MII data register if in read mode */
-	ret = read ? readl(mii_data) & MII_DATA_MASK : 0;
+	ret = read ? readl(mii_data) & MII_DATA_GD_MASK : 0;
 
 out:
 	pm_runtime_put(priv->device);
@@ -345,7 +345,7 @@ static int stmmac_mdio_write_c22(struct mii_bus *bus, int phyaddr, int phyreg,
 	if (priv->plat->has_gmac4)
 		cmd = MII_GMAC4_WRITE;
 	else
-		cmd = MII_WRITE;
+		cmd = MII_ADDR_GWRITE;
 
 	return stmmac_mdio_write(priv, phyaddr, phyreg, cmd, phydata);
 }
-- 
2.47.2

[PATCH net-next 08/11] net: stmmac: mdio: move initialisation of priv->clk_csr to stmmac_mdio

[Russell King (Oracle)]

The only user of priv->clk_csr is the MDIO code, so move its
initialisation to stmmac_mdio.c.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 .../net/ethernet/stmicro/stmmac/stmmac_main.c | 82 -----------------
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 88 ++++++++++++++++++-
 2 files changed, 86 insertions(+), 84 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index f0abd99fd137..419cb49ee5a2 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -314,77 +314,6 @@ static void stmmac_global_err(struct stmmac_priv *priv)
 	stmmac_service_event_schedule(priv);
 }
 
-/**
- * stmmac_clk_csr_set - dynamically set the MDC clock
- * @priv: driver private structure
- * Description: this is to dynamically set the MDC clock according to the csr
- * clock input.
- * Note:
- *	If a specific clk_csr value is passed from the platform
- *	this means that the CSR Clock Range selection cannot be
- *	changed at run-time and it is fixed (as reported in the driver
- *	documentation). Viceversa the driver will try to set the MDC
- *	clock dynamically according to the actual clock input.
- */
-static void stmmac_clk_csr_set(struct stmmac_priv *priv)
-{
-	unsigned long clk_rate;
-
-	clk_rate = clk_get_rate(priv->plat->stmmac_clk);
-
-	/* Platform provided default clk_csr would be assumed valid
-	 * for all other cases except for the below mentioned ones.
-	 * For values higher than the IEEE 802.3 specified frequency
-	 * we can not estimate the proper divider as it is not known
-	 * the frequency of clk_csr_i. So we do not change the default
-	 * divider.
-	 */
-	if (!(priv->clk_csr & MAC_CSR_H_FRQ_MASK)) {
-		if (clk_rate < CSR_F_35M)
-			priv->clk_csr = STMMAC_CSR_20_35M;
-		else if ((clk_rate >= CSR_F_35M) && (clk_rate < CSR_F_60M))
-			priv->clk_csr = STMMAC_CSR_35_60M;
-		else if ((clk_rate >= CSR_F_60M) && (clk_rate < CSR_F_100M))
-			priv->clk_csr = STMMAC_CSR_60_100M;
-		else if ((clk_rate >= CSR_F_100M) && (clk_rate < CSR_F_150M))
-			priv->clk_csr = STMMAC_CSR_100_150M;
-		else if ((clk_rate >= CSR_F_150M) && (clk_rate < CSR_F_250M))
-			priv->clk_csr = STMMAC_CSR_150_250M;
-		else if ((clk_rate >= CSR_F_250M) && (clk_rate <= CSR_F_300M))
-			priv->clk_csr = STMMAC_CSR_250_300M;
-		else if ((clk_rate >= CSR_F_300M) && (clk_rate < CSR_F_500M))
-			priv->clk_csr = STMMAC_CSR_300_500M;
-		else if ((clk_rate >= CSR_F_500M) && (clk_rate < CSR_F_800M))
-			priv->clk_csr = STMMAC_CSR_500_800M;
-	}
-
-	if (priv->plat->flags & STMMAC_FLAG_HAS_SUN8I) {
-		if (clk_rate > 160000000)
-			priv->clk_csr = 0x03;
-		else if (clk_rate > 80000000)
-			priv->clk_csr = 0x02;
-		else if (clk_rate > 40000000)
-			priv->clk_csr = 0x01;
-		else
-			priv->clk_csr = 0;
-	}
-
-	if (priv->plat->has_xgmac) {
-		if (clk_rate > 400000000)
-			priv->clk_csr = 0x5;
-		else if (clk_rate > 350000000)
-			priv->clk_csr = 0x4;
-		else if (clk_rate > 300000000)
-			priv->clk_csr = 0x3;
-		else if (clk_rate > 250000000)
-			priv->clk_csr = 0x2;
-		else if (clk_rate > 150000000)
-			priv->clk_csr = 0x1;
-		else
-			priv->clk_csr = 0x0;
-	}
-}
-
 static void print_pkt(unsigned char *buf, int len)
 {
 	pr_debug("len = %d byte, buf addr: 0x%p\n", len, buf);
@@ -7718,17 +7647,6 @@ int stmmac_dvr_probe(struct device *device,
 
 	stmmac_fpe_init(priv);
 
-	/* If a specific clk_csr value is passed from the platform
-	 * this means that the CSR Clock Range selection cannot be
-	 * changed at run-time and it is fixed. Viceversa the driver'll try to
-	 * set the MDC clock dynamically according to the csr actual
-	 * clock input.
-	 */
-	if (priv->plat->clk_csr >= 0)
-		priv->clk_csr = priv->plat->clk_csr;
-	else
-		stmmac_clk_csr_set(priv);
-
 	stmmac_check_pcs_mode(priv);
 
 	pm_runtime_get_noresume(device);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 4d0de3c269a8..2ba0938ac641 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -471,8 +471,92 @@ void stmmac_pcs_clean(struct net_device *ndev)
 	priv->hw->xpcs = NULL;
 }
 
-static void stmmac_mdio_bus_config(struct stmmac_priv *priv, u32 value)
+/**
+ * stmmac_clk_csr_set - dynamically set the MDC clock
+ * @priv: driver private structure
+ * Description: this is to dynamically set the MDC clock according to the csr
+ * clock input.
+ * Note:
+ *	If a specific clk_csr value is passed from the platform
+ *	this means that the CSR Clock Range selection cannot be
+ *	changed at run-time and it is fixed (as reported in the driver
+ *	documentation). Viceversa the driver will try to set the MDC
+ *	clock dynamically according to the actual clock input.
+ */
+static void stmmac_clk_csr_set(struct stmmac_priv *priv)
 {
+	unsigned long clk_rate;
+
+	clk_rate = clk_get_rate(priv->plat->stmmac_clk);
+
+	/* Platform provided default clk_csr would be assumed valid
+	 * for all other cases except for the below mentioned ones.
+	 * For values higher than the IEEE 802.3 specified frequency
+	 * we can not estimate the proper divider as it is not known
+	 * the frequency of clk_csr_i. So we do not change the default
+	 * divider.
+	 */
+	if (!(priv->clk_csr & MAC_CSR_H_FRQ_MASK)) {
+		if (clk_rate < CSR_F_35M)
+			priv->clk_csr = STMMAC_CSR_20_35M;
+		else if ((clk_rate >= CSR_F_35M) && (clk_rate < CSR_F_60M))
+			priv->clk_csr = STMMAC_CSR_35_60M;
+		else if ((clk_rate >= CSR_F_60M) && (clk_rate < CSR_F_100M))
+			priv->clk_csr = STMMAC_CSR_60_100M;
+		else if ((clk_rate >= CSR_F_100M) && (clk_rate < CSR_F_150M))
+			priv->clk_csr = STMMAC_CSR_100_150M;
+		else if ((clk_rate >= CSR_F_150M) && (clk_rate < CSR_F_250M))
+			priv->clk_csr = STMMAC_CSR_150_250M;
+		else if ((clk_rate >= CSR_F_250M) && (clk_rate <= CSR_F_300M))
+			priv->clk_csr = STMMAC_CSR_250_300M;
+		else if ((clk_rate >= CSR_F_300M) && (clk_rate < CSR_F_500M))
+			priv->clk_csr = STMMAC_CSR_300_500M;
+		else if ((clk_rate >= CSR_F_500M) && (clk_rate < CSR_F_800M))
+			priv->clk_csr = STMMAC_CSR_500_800M;
+	}
+
+	if (priv->plat->flags & STMMAC_FLAG_HAS_SUN8I) {
+		if (clk_rate > 160000000)
+			priv->clk_csr = 0x03;
+		else if (clk_rate > 80000000)
+			priv->clk_csr = 0x02;
+		else if (clk_rate > 40000000)
+			priv->clk_csr = 0x01;
+		else
+			priv->clk_csr = 0;
+	}
+
+	if (priv->plat->has_xgmac) {
+		if (clk_rate > 400000000)
+			priv->clk_csr = 0x5;
+		else if (clk_rate > 350000000)
+			priv->clk_csr = 0x4;
+		else if (clk_rate > 300000000)
+			priv->clk_csr = 0x3;
+		else if (clk_rate > 250000000)
+			priv->clk_csr = 0x2;
+		else if (clk_rate > 150000000)
+			priv->clk_csr = 0x1;
+		else
+			priv->clk_csr = 0x0;
+	}
+}
+
+static void stmmac_mdio_bus_config(struct stmmac_priv *priv)
+{
+	u32 value;
+
+	/* If a specific clk_csr value is passed from the platform, this means
+	 * that the CSR Clock Range value should not be computed from the CSR
+	 * clock.
+	 */
+	if (priv->plat->clk_csr >= 0) {
+		value = priv->plat->clk_csr;
+	} else {
+		stmmac_clk_csr_set(priv);
+		value = priv->clk_csr;
+	}
+
 	value <<= priv->hw->mii.clk_csr_shift;
 
 	if (value & ~priv->hw->mii.clk_csr_mask)
@@ -503,7 +587,7 @@ int stmmac_mdio_register(struct net_device *ndev)
 	if (!mdio_bus_data)
 		return 0;
 
-	stmmac_mdio_bus_config(priv, priv->clk_csr);
+	stmmac_mdio_bus_config(priv);
 
 	new_bus = mdiobus_alloc();
 	if (!new_bus)
-- 
2.47.2

[PATCH net-next 09/11] net: stmmac: mdio: return clk_csr value from stmmac_clk_csr_set()

[Russell King (Oracle)]

Return the clk_csr value from stmmac_clk_csr_set() rather than
using priv->clk_csr, as this struct member now serves very little
purpose. This allows us to remove priv->clk_csr.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac.h  |  1 -
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 67 +++++++++----------
 2 files changed, 33 insertions(+), 35 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index 4d5577935b13..ec6bccb13710 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -289,7 +289,6 @@ struct stmmac_priv {
 	u32 msg_enable;
 	int wolopts;
 	int wol_irq;
-	int clk_csr;
 	u32 gmii_address_bus_config;
 	struct timer_list eee_ctrl_timer;
 	int lpi_irq;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 2ba0938ac641..7326cf5401cc 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -483,9 +483,10 @@ void stmmac_pcs_clean(struct net_device *ndev)
  *	documentation). Viceversa the driver will try to set the MDC
  *	clock dynamically according to the actual clock input.
  */
-static void stmmac_clk_csr_set(struct stmmac_priv *priv)
+static u32 stmmac_clk_csr_set(struct stmmac_priv *priv)
 {
 	unsigned long clk_rate;
+	u32 value = ~0;
 
 	clk_rate = clk_get_rate(priv->plat->stmmac_clk);
 
@@ -496,50 +497,50 @@ static void stmmac_clk_csr_set(struct stmmac_priv *priv)
 	 * the frequency of clk_csr_i. So we do not change the default
 	 * divider.
 	 */
-	if (!(priv->clk_csr & MAC_CSR_H_FRQ_MASK)) {
-		if (clk_rate < CSR_F_35M)
-			priv->clk_csr = STMMAC_CSR_20_35M;
-		else if ((clk_rate >= CSR_F_35M) && (clk_rate < CSR_F_60M))
-			priv->clk_csr = STMMAC_CSR_35_60M;
-		else if ((clk_rate >= CSR_F_60M) && (clk_rate < CSR_F_100M))
-			priv->clk_csr = STMMAC_CSR_60_100M;
-		else if ((clk_rate >= CSR_F_100M) && (clk_rate < CSR_F_150M))
-			priv->clk_csr = STMMAC_CSR_100_150M;
-		else if ((clk_rate >= CSR_F_150M) && (clk_rate < CSR_F_250M))
-			priv->clk_csr = STMMAC_CSR_150_250M;
-		else if ((clk_rate >= CSR_F_250M) && (clk_rate <= CSR_F_300M))
-			priv->clk_csr = STMMAC_CSR_250_300M;
-		else if ((clk_rate >= CSR_F_300M) && (clk_rate < CSR_F_500M))
-			priv->clk_csr = STMMAC_CSR_300_500M;
-		else if ((clk_rate >= CSR_F_500M) && (clk_rate < CSR_F_800M))
-			priv->clk_csr = STMMAC_CSR_500_800M;
-	}
+	if (clk_rate < CSR_F_35M)
+		value = STMMAC_CSR_20_35M;
+	else if ((clk_rate >= CSR_F_35M) && (clk_rate < CSR_F_60M))
+		value = STMMAC_CSR_35_60M;
+	else if ((clk_rate >= CSR_F_60M) && (clk_rate < CSR_F_100M))
+		value = STMMAC_CSR_60_100M;
+	else if ((clk_rate >= CSR_F_100M) && (clk_rate < CSR_F_150M))
+		value = STMMAC_CSR_100_150M;
+	else if ((clk_rate >= CSR_F_150M) && (clk_rate < CSR_F_250M))
+		value = STMMAC_CSR_150_250M;
+	else if ((clk_rate >= CSR_F_250M) && (clk_rate <= CSR_F_300M))
+		value = STMMAC_CSR_250_300M;
+	else if ((clk_rate >= CSR_F_300M) && (clk_rate < CSR_F_500M))
+		value = STMMAC_CSR_300_500M;
+	else if ((clk_rate >= CSR_F_500M) && (clk_rate < CSR_F_800M))
+		value = STMMAC_CSR_500_800M;
 
 	if (priv->plat->flags & STMMAC_FLAG_HAS_SUN8I) {
 		if (clk_rate > 160000000)
-			priv->clk_csr = 0x03;
+			value = 0x03;
 		else if (clk_rate > 80000000)
-			priv->clk_csr = 0x02;
+			value = 0x02;
 		else if (clk_rate > 40000000)
-			priv->clk_csr = 0x01;
+			value = 0x01;
 		else
-			priv->clk_csr = 0;
+			value = 0;
 	}
 
 	if (priv->plat->has_xgmac) {
 		if (clk_rate > 400000000)
-			priv->clk_csr = 0x5;
+			value = 0x5;
 		else if (clk_rate > 350000000)
-			priv->clk_csr = 0x4;
+			value = 0x4;
 		else if (clk_rate > 300000000)
-			priv->clk_csr = 0x3;
+			value = 0x3;
 		else if (clk_rate > 250000000)
-			priv->clk_csr = 0x2;
+			value = 0x2;
 		else if (clk_rate > 150000000)
-			priv->clk_csr = 0x1;
+			value = 0x1;
 		else
-			priv->clk_csr = 0x0;
+			value = 0x0;
 	}
+
+	return value;
 }
 
 static void stmmac_mdio_bus_config(struct stmmac_priv *priv)
@@ -550,12 +551,10 @@ static void stmmac_mdio_bus_config(struct stmmac_priv *priv)
 	 * that the CSR Clock Range value should not be computed from the CSR
 	 * clock.
 	 */
-	if (priv->plat->clk_csr >= 0) {
+	if (priv->plat->clk_csr >= 0)
 		value = priv->plat->clk_csr;
-	} else {
-		stmmac_clk_csr_set(priv);
-		value = priv->clk_csr;
-	}
+	else
+		value = stmmac_clk_csr_set(priv);
 
 	value <<= priv->hw->mii.clk_csr_shift;
 
-- 
2.47.2

[PATCH net-next 10/11] net: stmmac: mdio: remove redundant clock rate tests

[Russell King (Oracle)]

The pattern:

	... if (v < A)
		...
	else if (v >= A && v < B)
		...

can be simplified to:

	... if (v < A)
		...
	else if (v < B)
		...

which makes the string of ifelse more readable.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 7326cf5401cc..4c1a60ce9d42 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -499,19 +499,19 @@ static u32 stmmac_clk_csr_set(struct stmmac_priv *priv)
 	 */
 	if (clk_rate < CSR_F_35M)
 		value = STMMAC_CSR_20_35M;
-	else if ((clk_rate >= CSR_F_35M) && (clk_rate < CSR_F_60M))
+	else if (clk_rate < CSR_F_60M)
 		value = STMMAC_CSR_35_60M;
-	else if ((clk_rate >= CSR_F_60M) && (clk_rate < CSR_F_100M))
+	else if (clk_rate < CSR_F_100M)
 		value = STMMAC_CSR_60_100M;
-	else if ((clk_rate >= CSR_F_100M) && (clk_rate < CSR_F_150M))
+	else if (clk_rate < CSR_F_150M)
 		value = STMMAC_CSR_100_150M;
-	else if ((clk_rate >= CSR_F_150M) && (clk_rate < CSR_F_250M))
+	else if (clk_rate < CSR_F_250M)
 		value = STMMAC_CSR_150_250M;
-	else if ((clk_rate >= CSR_F_250M) && (clk_rate <= CSR_F_300M))
+	else if (clk_rate <= CSR_F_300M)
 		value = STMMAC_CSR_250_300M;
-	else if ((clk_rate >= CSR_F_300M) && (clk_rate < CSR_F_500M))
+	else if (clk_rate < CSR_F_500M)
 		value = STMMAC_CSR_300_500M;
-	else if ((clk_rate >= CSR_F_500M) && (clk_rate < CSR_F_800M))
+	else if (clk_rate < CSR_F_800M)
 		value = STMMAC_CSR_500_800M;
 
 	if (priv->plat->flags & STMMAC_FLAG_HAS_SUN8I) {
-- 
2.47.2

[PATCH net-next 11/11] net: stmmac: use STMMAC_CSR_xxx definitions in platform glue

[Russell King (Oracle)]

Use the STMMAC_CSR_xxx definitions to initialise plat->clk_csr in the
platform glue drivers to make the integer values meaningful.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c    | 5 +++--
 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 3 ++-
 drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c     | 5 +++--
 3 files changed, 8 insertions(+), 5 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
index 3fac3945cbfa..d900b93f46ce 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
@@ -566,7 +566,8 @@ static int intel_mac_finish(struct net_device *ndev,
 
 static void common_default_data(struct plat_stmmacenet_data *plat)
 {
-	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
+	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
+	plat->clk_csr = STMMAC_CSR_20_35M;
 	plat->has_gmac = 1;
 	plat->force_sf_dma_mode = 1;
 
@@ -613,7 +614,7 @@ static int intel_mgbe_common_data(struct pci_dev *pdev,
 
 	plat->pdev = pdev;
 	plat->phy_addr = -1;
-	plat->clk_csr = 5;
+	plat->clk_csr = STMMAC_CSR_250_300M;
 	plat->has_gmac = 0;
 	plat->has_gmac4 = 1;
 	plat->force_sf_dma_mode = 0;
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
index 6fca0fca4892..dd82dc2189e9 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
@@ -90,7 +90,8 @@ static void loongson_default_data(struct pci_dev *pdev,
 	/* Get bus_id, this can be overwritten later */
 	plat->bus_id = pci_dev_id(pdev);
 
-	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
+	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
+	plat->clk_csr = STMMAC_CSR_20_35M;
 	plat->has_gmac = 1;
 	plat->force_sf_dma_mode = 1;
 
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
index e6a7d0ddac2a..4e3aa611fda8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
@@ -21,7 +21,8 @@ struct stmmac_pci_info {
 
 static void common_default_data(struct plat_stmmacenet_data *plat)
 {
-	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
+	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
+	plat->clk_csr = STMMAC_CSR_20_35M;
 	plat->has_gmac = 1;
 	plat->force_sf_dma_mode = 1;
 
@@ -74,7 +75,7 @@ static int snps_gmac5_default_data(struct pci_dev *pdev,
 {
 	int i;
 
-	plat->clk_csr = 5;
+	plat->clk_csr = STMMAC_CSR_250_300M;
 	plat->has_gmac4 = 1;
 	plat->force_sf_dma_mode = 1;
 	plat->flags |= STMMAC_FLAG_TSO_EN;
-- 
2.47.2

Re: [PATCH net-next 00/11] net: stmmac: mdio cleanups

[Russell King (Oracle)]

On Wed, Sep 03, 2025 at 01:38:57PM +0100, Russell King (Oracle) wrote:
> Hi,
> 
> Clean up the stmmac MDIO code:
> - provide an address register formatter to avoid repeated code
> - provide a common function to wait for the busy bit to clear
> - pre-compute the CR field (mdio clock divider)
> - move address formatter into read/write functions
> - combine the read/write functions into a common accessor function
> - move runtime PM handling into common accessor function
> - rename register constants to better reflect manufacturer names
> - move stmmac_clk_csr_set() into stmmac_mdio
> - make stmmac_clk_csr_set() return the CR field value and remove
>   priv->clk_csr
> - clean up if() range tests in stmmac_clk_csr_set()
> - use STMMAC_CSR_xxx definitions in initialisers

It would be great if someone can test this series please.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!