Re: [RFC PATCH v7 1/8] dpll: spec: Add Netlink spec in YAML

[Jiri Pirko <jiri@resnulli.us>]

Tue, May 16, 2023 at 02:05:38PM CEST, arkadiusz.kubalewski@intel.com wrote:
>>From: Jiri Pirko <jiri@resnulli.us>
>>Sent: Monday, May 15, 2023 11:31 AM
>>
>>Thu, May 11, 2023 at 10:51:43PM CEST, arkadiusz.kubalewski@intel.com wrote:
>>>>From: Jiri Pirko <jiri@resnulli.us>
>>>>Sent: Thursday, May 11, 2023 10:00 AM
>>>>
>>>>Thu, May 11, 2023 at 09:40:26AM CEST, arkadiusz.kubalewski@intel.com wrote:
>>>>>>From: Jakub Kicinski <kuba@kernel.org>
>>>>>>Sent: Thursday, May 4, 2023 11:25 PM
>>>>>>
>>>>>>On Thu, 4 May 2023 14:02:30 +0200 Jiri Pirko wrote:
>>>>>>> >+definitions:
>>>>>>> >+  -
>>>>>>> >+    type: enum
>>>>>>> >+    name: mode
>>>>>>> >+    doc: |
>>>>>>> >+      working-modes a dpll can support, differentiate if and how dpll
>>>>>>>selects
>>>>>>> >+      one of its sources to syntonize with it, valid values for
>>>>>>>DPLL_A_MODE
>>>>>>> >+      attribute
>>>>>>> >+    entries:
>>>>>>> >+      -
>>>>>>> >+        name: unspec
>>>>>>>
>>>>>>> In general, why exactly do we need unspec values in enums and CMDs?
>>>>>>> What is the usecase. If there isn't please remove.
>>>>>>
>>>>>>+1
>>>>>>
>>>>>
>>>>>Sure, fixed.
>>>>>
>>>>>>> >+        doc: unspecified value
>>>>>>> >+      -
>>>>>>> >+        name: manual
>>>>>>
>>>>>>I think the documentation calls this "forced", still.
>>>>>>
>>>>>
>>>>>Yes, good catch, fixed docs.
>>>>>
>>>>>>> >+        doc: source can be only selected by sending a request to dpll
>>>>>>> >+      -
>>>>>>> >+        name: automatic
>>>>>>> >+        doc: highest prio, valid source, auto selected by dpll
>>>>>>> >+      -
>>>>>>> >+        name: holdover
>>>>>>> >+        doc: dpll forced into holdover mode
>>>>>>> >+      -
>>>>>>> >+        name: freerun
>>>>>>> >+        doc: dpll driven on system clk, no holdover available
>>>>>>>
>>>>>>> Remove "no holdover available". This is not a state, this is a mode
>>>>>>> configuration. If holdover is or isn't available, is a runtime info.
>>>>>>
>>>>>>Agreed, seems a little confusing now. Should we expose the system clk
>>>>>>as a pin to be able to force lock to it? Or there's some extra magic
>>>>>>at play here?
>>>>>
>>>>>In freerun you cannot lock to anything it, it just uses system clock from
>>>>>one of designated chip wires (which is not a part of source pins pool) to
>>>>>feed the dpll. Dpll would only stabilize that signal and pass it further.
>>>>>Locking itself is some kind of magic, as it usually takes at least ~15
>>>>>seconds before it locks to a signal once it is selected.
>>>>>
>>>>>>
>>>>>>> >+      -
>>>>>>> >+        name: nco
>>>>>>> >+        doc: dpll driven by Numerically Controlled Oscillator
>>>>>>
>>>>>>Noob question, what is NCO in terms of implementation?
>>>>>>We source the signal from an arbitrary pin and FW / driver does
>>>>>>the control? Or we always use system refclk and then tune?
>>>>>>
>>>>>
>>>>>Documentation of chip we are using, stated NCO as similar to FREERUN, and
>>>>>it
>>>>
>>>>So how exactly this is different to freerun? Does user care or he would
>>>>be fine with "freerun" in this case? My point is, isn't "NCO" some
>>>>device specific thing that should be abstracted out here?
>>>>
>>>
>>>Sure, it is device specific, some synchronizing circuits would have this
>>>capability, while others would not.
>>>Should be abstracted out? It is a good question.. shall user know that he is
>>>in
>>>freerun with possibility to control the frequency or not?
>>>Let's say we remove NCO, and have dpll with enabled FREERUN mode and pins
>>>supporting multiple output frequencies.
>>>How the one would know if those frequencies are supported only in
>>>MANUAL/AUTOMATIC modes or also in the FREERUN mode?
>>>In other words: As the user can I change a frequency of a dpll if active
>>>mode is FREERUN?
>>
>>Okay, I think I'm deep in the DPLL infra you are pushing, but my
>>understanding that you can control frequency in NCO mode is not present
>>:/ That only means it may be confusing and not described properly.
>>How do you control this frequency exactly? I see no such knob.
>>
>
>The set frequency is there already, although we miss phase offset I guess.

Yeah, but on a pin, right?



>
>But I have changed my mind on having this in the kernel..
>Initially I have added this mode as our HW supports it, while thinking that
>dpll subsystem shall have this, and we will implement it one day..
>But as we have not implemented it yet, let's leave work and discussion on
>this mode for the future, when someone will actually try to implement it.

Yeah, let's drop it then. One less confusing thing to wrap a head around :)


>
>>Can't the oscilator be modeled as a pin and then you are not in freerun
>>but locked this "internal pin"? We know how to control frequency there.
>>
>
>Hmm, yeah probably could work this way.
>
>
>Thank you!
>Arkadiusz
>
>>
>>>
>>>I would say it is better to have such mode, we could argue on naming though.
>>>
>>>>
>>>>>runs on a SYSTEM CLOCK provided to the chip (plus some stabilization and
>>>>>dividers before it reaches the output).
>>>>>It doesn't count as an source pin, it uses signal form dedicated wire for
>>>>>SYSTEM CLOCK.
>>>>>In this case control over output frequency is done by synchronizer chip
>>>>>firmware, but still it will not lock to any source pin signal.
>>>>>
>>>>>>> >+    render-max: true
>>>>>>> >+  -
>>>>>>> >+    type: enum
>>>>>>> >+    name: lock-status
>>>>>>> >+    doc: |
>>>>>>> >+      provides information of dpll device lock status, valid values for
>>>>>>> >+      DPLL_A_LOCK_STATUS attribute
>>>>>>> >+    entries:
>>>>>>> >+      -
>>>>>>> >+        name: unspec
>>>>>>> >+        doc: unspecified value
>>>>>>> >+      -
>>>>>>> >+        name: unlocked
>>>>>>> >+        doc: |
>>>>>>> >+          dpll was not yet locked to any valid source (or is in one of
>>>>>>> >+          modes: DPLL_MODE_FREERUN, DPLL_MODE_NCO)
>>>>>>> >+      -
>>>>>>> >+        name: calibrating
>>>>>>> >+        doc: dpll is trying to lock to a valid signal
>>>>>>> >+      -
>>>>>>> >+        name: locked
>>>>>>> >+        doc: dpll is locked
>>>>>>> >+      -
>>>>>>> >+        name: holdover
>>>>>>> >+        doc: |
>>>>>>> >+          dpll is in holdover state - lost a valid lock or was forced by
>>>>>>> >+          selecting DPLL_MODE_HOLDOVER mode
>>>>>>>
>>>>>>> Is it needed to mention the holdover mode. It's slightly confusing,
>>>>>>> because user might understand that the lock-status is always "holdover"
>>>>>>> in case of "holdover" mode. But it could be "unlocked", can't it?
>>>>>>> Perhaps I don't understand the flows there correctly :/
>>>>>>
>>>>>>Hm, if we want to make sure that holdover mode must result in holdover
>>>>>>state then we need some extra atomicity requirements on the SET
>>>>>>operation. To me it seems logical enough that after setting holdover
>>>>>>mode we'll end up either in holdover or unlocked status, depending on
>>>>>>lock status when request reached the HW.
>>>>>>
>>>>>
>>>>>Improved the docs:
>>>>>        name: holdover
>>>>>        doc: |
>>>>>          dpll is in holdover state - lost a valid lock or was forced
>>>>>          by selecting DPLL_MODE_HOLDOVER mode (latter possible only
>>>>>          when dpll lock-state was already DPLL_LOCK_STATUS_LOCKED,
>>>>>	  if it was not, the dpll's lock-status will remain
>>>>
>>>>"if it was not" does not really cope with the sentence above that. Could
>>>>you iron-out the phrasing a bit please?
>>>
>>>
>>>Hmmm,
>>>        name: holdover
>>>        doc: |
>>>          dpll is in holdover state - lost a valid lock or was forced
>>>          by selecting DPLL_MODE_HOLDOVER mode (latter possible only
>>>          when dpll lock-state was already DPLL_LOCK_STATUS_LOCKED,
>>>          if dpll lock-state was not DPLL_LOCK_STATUS_LOCKED, the
>>>          dpll's lock-state shall remain DPLL_LOCK_STATUS_UNLOCKED
>>>          even if DPLL_MODE_HOLDOVER was requested)
>>>
>>>Hope this is better?
>>
>>Okay.
>>
>>>
>>>
>>>Thank you!
>>>Arkadiusz
>>>
>>>[...]