From: Zixian Zeng <sycamoremoon376@gmail.com>
To: Michael Walle <mwalle@kernel.org>,
Tudor Ambarus <tudor.ambarus@linaro.org>,
Pratyush Yadav <pratyush@kernel.org>,
Miquel Raynal <miquel.raynal@bootlin.com>,
Richard Weinberger <richard@nod.at>,
Vignesh Raghavendra <vigneshr@ti.com>,
Chen Wang <unicorn_wang@outlook.com>,
Inochi Amaoto <inochiama@gmail.com>,
Mark Brown <broonie@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
Albert Ou <aou@eecs.berkeley.edu>,
Alexandre Ghiti <alex@ghiti.fr>,
Longbin Li <looong.bin@gmail.com>
Cc: linux-mtd@lists.infradead.org, linux-kernel@vger.kernel.org,
sophgo@lists.linux.dev, linux-spi@vger.kernel.org,
devicetree@vger.kernel.org, linux-riscv@lists.infradead.org,
dlan@gentoo.org, ziyao@disroot.org
Subject: Re: [PATCH 2/3] mtd: spi-nor: Add GD25LB512ME GigaDevice flash_info
Date: Sat, 24 May 2025 00:18:59 +0800 [thread overview]
Message-ID: <aDCf84cRw0tmcAbm@calculate> (raw)
In-Reply-To: <DA3HXNN7HTD2.2NUKORU5V6CS2@kernel.org>
Hi, Michael, Thank you for your reviews.
On Fri, May 23, 2025 at 01:16:50PM +0200, Michael Walle wrote:
> Hi,
>
> > Add GD25LB512ME SPI-NOR flash information
>
> Please have a look at [1].
>
> This flash supports SFDP, do you really need a new entry in the
> flashdb? Could you try without it?
>
> In any case, could you please dump the SFDP see [1], too.
>
> [1] https://docs.kernel.org/driver-api/mtd/spi-nor.html
>
> -michael
I was following the testing requirements from [1].
Before that, I have applied the patch:
"mtd: spi-nor: Add GD25LB512ME GigaDevice flash_info"
Because without this patch, the spi-nor device cannot be detected normally.
------------------------------- LOG ------------------------------------
root@localhost ~ # dmesg | grep -i spi
[ 10.199526] spi-nor spi0.0: supply vcc not found, using dummy regulator
[ 11.206477] spi-nor spi0.0: unrecognized JEDEC id bytes: c8 67 1a ff c8 67
[ 11.213691] spi-nor spi1.0: supply vcc not found, using dummy regulator
[ 12.220614] spi-nor spi1.0: unrecognized JEDEC id bytes: c8 67 1a ff c8 67
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
cat: /sys/bus/spi/devices/spi0.0/spi-nor/partname: No such file or directory
Testing output atfer that patch:
------------------------------------------------------------------------
This flash is populated on the SG2042 Pioneer board and was tested at
100MHz frequency using the spi-sg2044-nor SPI controller.
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
gd25lb512me
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c8671a
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
gigadevice
root@localhost ~ # xxd -p /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
53464450060102ff00060110300000ffc8000103900000ff84000102c000
00ffffffffffffffffffffffffffffffffffe520eaffffffff1f44eb086b
003b00bbfeffffffffff00ffffff44eb0c200f5210d800ffd531b1fe83d6
1458ec6006337a757a7504bdd55c2906740008500001ffffffffffffffff
ffffffffffffffffffffffffffffffffffffffffffffffff002050169df9
8156d9c8ffffffffffffffffffffffffffffffffffffffffffffffffffff
fffffffffffffffffffffffff38ff0ff215cdcff
root@localhost ~ # sha256sum /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
859eb314b0500aa3e3dc5a1ad514f1013387c7aaa40147ed2d616ffc4b6d851c /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
root@localhost ~ # #Dump debugfs data
root@localhost ~ # cat /sys/kernel/debug/spi-nor/spi0.0/capabilities
Supported read modes by the flash
1S-1S-1S
opcode 0x13
mode cycles 0
dummy cycles 0
1S-1S-4S
opcode 0x6c
mode cycles 0
dummy cycles 8
1S-4S-4S
opcode 0xec
mode cycles 2
dummy cycles 4
4S-4S-4S
opcode 0xec
mode cycles 2
dummy cycles 4
Supported page program modes by the flash
1S-1S-1S
opcode 0x12
1S-1S-4S
opcode 0x34
1S-4S-4S
opcode 0x3e
root@localhost ~ # cat /sys/kernel/debug/spi-nor/spi0.0/params
name gd25lb512me
id c8 67 1a ff c8 67
size 64.0 MiB
write size 1
page size 256
address nbytes 4
flags HAS_SR_TB | 4B_OPCODES | HAS_4BAIT | HAS_LOCK | HAS_16BIT_SR | SOFT_RESET
opcodes
read 0x13
dummy cycles 0
erase 0x21
program 0x12
8D extension none
protocols
read 1S-1S-1S
write 1S-1S-1S
register 1S-1S-1S
erase commands
21 (4.00 KiB) [1]
5c (32.0 KiB) [2]
dc (64.0 KiB) [3]
c7 (64.0 MiB)
sector map
region (in hex) | erase mask | overlaid
------------------+------------+----------
00000000-03ffffff | [ 1 ] | no
root@localhost ~ # dd if=/dev/urandom of=./spi_test bs=1M count=2
2+0 records in
2+0 records out
2097152 bytes (2.1 MB, 2.0 MiB) copied, 0.0279486 s, 75.0 MB/s
root@localhost ~ # mtd_debug erase /dev/mtd0 0 2097152
Erased 2097152 bytes from address 0x00000000 in flash
root@localhost ~ # mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
root@localhost ~ # hexdump spi_read
0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0200000
root@localhost ~ # sha256sum spi_read
4bda3a28f4ffe603c0ec1258c0034d65a1a0d35ab7bd523a834608adabf03cc5 spi_read
root@localhost ~ # mtd_debug write /dev/mtd0 0 2097152 spi_test
Copied 2097152 bytes from spi_test to address 0x00000000 in flash
root@localhost ~ # mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
root@localhost ~ # sha256sum spi*
a2ebfaebe38974847a4efb628b29a72f1d50e78c17318869d8954b033dc32e5d spi_read
a2ebfaebe38974847a4efb628b29a72f1d50e78c17318869d8954b033dc32e5d spi_test
root@localhost ~ # mtd_debug info /dev/mtd0
mtd.type = MTD_NORFLASH
mtd.flags = MTD_CAP_NORFLASH
mtd.size = 67108864 (64M)
mtd.erasesize = 4096 (4K)
mtd.writesize = 1
mtd.oobsize = 0
regions = 0
------------------------------------------------------------------------
Best regards,
Zixian
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
WARNING: multiple messages have this Message-ID (diff)
From: Zixian Zeng <sycamoremoon376@gmail.com>
To: Michael Walle <mwalle@kernel.org>,
Tudor Ambarus <tudor.ambarus@linaro.org>,
Pratyush Yadav <pratyush@kernel.org>,
Miquel Raynal <miquel.raynal@bootlin.com>,
Richard Weinberger <richard@nod.at>,
Vignesh Raghavendra <vigneshr@ti.com>,
Chen Wang <unicorn_wang@outlook.com>,
Inochi Amaoto <inochiama@gmail.com>,
Mark Brown <broonie@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
Albert Ou <aou@eecs.berkeley.edu>,
Alexandre Ghiti <alex@ghiti.fr>,
Longbin Li <looong.bin@gmail.com>
Cc: linux-mtd@lists.infradead.org, linux-kernel@vger.kernel.org,
sophgo@lists.linux.dev, linux-spi@vger.kernel.org,
devicetree@vger.kernel.org, linux-riscv@lists.infradead.org,
dlan@gentoo.org, ziyao@disroot.org
Subject: Re: [PATCH 2/3] mtd: spi-nor: Add GD25LB512ME GigaDevice flash_info
Date: Sat, 24 May 2025 00:18:59 +0800 [thread overview]
Message-ID: <aDCf84cRw0tmcAbm@calculate> (raw)
In-Reply-To: <DA3HXNN7HTD2.2NUKORU5V6CS2@kernel.org>
Hi, Michael, Thank you for your reviews.
On Fri, May 23, 2025 at 01:16:50PM +0200, Michael Walle wrote:
> Hi,
>
> > Add GD25LB512ME SPI-NOR flash information
>
> Please have a look at [1].
>
> This flash supports SFDP, do you really need a new entry in the
> flashdb? Could you try without it?
>
> In any case, could you please dump the SFDP see [1], too.
>
> [1] https://docs.kernel.org/driver-api/mtd/spi-nor.html
>
> -michael
I was following the testing requirements from [1].
Before that, I have applied the patch:
"mtd: spi-nor: Add GD25LB512ME GigaDevice flash_info"
Because without this patch, the spi-nor device cannot be detected normally.
------------------------------- LOG ------------------------------------
root@localhost ~ # dmesg | grep -i spi
[ 10.199526] spi-nor spi0.0: supply vcc not found, using dummy regulator
[ 11.206477] spi-nor spi0.0: unrecognized JEDEC id bytes: c8 67 1a ff c8 67
[ 11.213691] spi-nor spi1.0: supply vcc not found, using dummy regulator
[ 12.220614] spi-nor spi1.0: unrecognized JEDEC id bytes: c8 67 1a ff c8 67
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
cat: /sys/bus/spi/devices/spi0.0/spi-nor/partname: No such file or directory
Testing output atfer that patch:
------------------------------------------------------------------------
This flash is populated on the SG2042 Pioneer board and was tested at
100MHz frequency using the spi-sg2044-nor SPI controller.
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
gd25lb512me
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c8671a
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
gigadevice
root@localhost ~ # xxd -p /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
53464450060102ff00060110300000ffc8000103900000ff84000102c000
00ffffffffffffffffffffffffffffffffffe520eaffffffff1f44eb086b
003b00bbfeffffffffff00ffffff44eb0c200f5210d800ffd531b1fe83d6
1458ec6006337a757a7504bdd55c2906740008500001ffffffffffffffff
ffffffffffffffffffffffffffffffffffffffffffffffff002050169df9
8156d9c8ffffffffffffffffffffffffffffffffffffffffffffffffffff
fffffffffffffffffffffffff38ff0ff215cdcff
root@localhost ~ # sha256sum /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
859eb314b0500aa3e3dc5a1ad514f1013387c7aaa40147ed2d616ffc4b6d851c /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
root@localhost ~ # #Dump debugfs data
root@localhost ~ # cat /sys/kernel/debug/spi-nor/spi0.0/capabilities
Supported read modes by the flash
1S-1S-1S
opcode 0x13
mode cycles 0
dummy cycles 0
1S-1S-4S
opcode 0x6c
mode cycles 0
dummy cycles 8
1S-4S-4S
opcode 0xec
mode cycles 2
dummy cycles 4
4S-4S-4S
opcode 0xec
mode cycles 2
dummy cycles 4
Supported page program modes by the flash
1S-1S-1S
opcode 0x12
1S-1S-4S
opcode 0x34
1S-4S-4S
opcode 0x3e
root@localhost ~ # cat /sys/kernel/debug/spi-nor/spi0.0/params
name gd25lb512me
id c8 67 1a ff c8 67
size 64.0 MiB
write size 1
page size 256
address nbytes 4
flags HAS_SR_TB | 4B_OPCODES | HAS_4BAIT | HAS_LOCK | HAS_16BIT_SR | SOFT_RESET
opcodes
read 0x13
dummy cycles 0
erase 0x21
program 0x12
8D extension none
protocols
read 1S-1S-1S
write 1S-1S-1S
register 1S-1S-1S
erase commands
21 (4.00 KiB) [1]
5c (32.0 KiB) [2]
dc (64.0 KiB) [3]
c7 (64.0 MiB)
sector map
region (in hex) | erase mask | overlaid
------------------+------------+----------
00000000-03ffffff | [ 1 ] | no
root@localhost ~ # dd if=/dev/urandom of=./spi_test bs=1M count=2
2+0 records in
2+0 records out
2097152 bytes (2.1 MB, 2.0 MiB) copied, 0.0279486 s, 75.0 MB/s
root@localhost ~ # mtd_debug erase /dev/mtd0 0 2097152
Erased 2097152 bytes from address 0x00000000 in flash
root@localhost ~ # mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
root@localhost ~ # hexdump spi_read
0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0200000
root@localhost ~ # sha256sum spi_read
4bda3a28f4ffe603c0ec1258c0034d65a1a0d35ab7bd523a834608adabf03cc5 spi_read
root@localhost ~ # mtd_debug write /dev/mtd0 0 2097152 spi_test
Copied 2097152 bytes from spi_test to address 0x00000000 in flash
root@localhost ~ # mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
root@localhost ~ # sha256sum spi*
a2ebfaebe38974847a4efb628b29a72f1d50e78c17318869d8954b033dc32e5d spi_read
a2ebfaebe38974847a4efb628b29a72f1d50e78c17318869d8954b033dc32e5d spi_test
root@localhost ~ # mtd_debug info /dev/mtd0
mtd.type = MTD_NORFLASH
mtd.flags = MTD_CAP_NORFLASH
mtd.size = 67108864 (64M)
mtd.erasesize = 4096 (4K)
mtd.writesize = 1
mtd.oobsize = 0
regions = 0
------------------------------------------------------------------------
Best regards,
Zixian
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
WARNING: multiple messages have this Message-ID (diff)
From: Zixian Zeng <sycamoremoon376@gmail.com>
To: Michael Walle <mwalle@kernel.org>,
Tudor Ambarus <tudor.ambarus@linaro.org>,
Pratyush Yadav <pratyush@kernel.org>,
Miquel Raynal <miquel.raynal@bootlin.com>,
Richard Weinberger <richard@nod.at>,
Vignesh Raghavendra <vigneshr@ti.com>,
Chen Wang <unicorn_wang@outlook.com>,
Inochi Amaoto <inochiama@gmail.com>,
Mark Brown <broonie@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
Albert Ou <aou@eecs.berkeley.edu>,
Alexandre Ghiti <alex@ghiti.fr>,
Longbin Li <looong.bin@gmail.com>
Cc: linux-mtd@lists.infradead.org, linux-kernel@vger.kernel.org,
sophgo@lists.linux.dev, linux-spi@vger.kernel.org,
devicetree@vger.kernel.org, linux-riscv@lists.infradead.org,
dlan@gentoo.org, ziyao@disroot.org
Subject: Re: [PATCH 2/3] mtd: spi-nor: Add GD25LB512ME GigaDevice flash_info
Date: Sat, 24 May 2025 00:18:59 +0800 [thread overview]
Message-ID: <aDCf84cRw0tmcAbm@calculate> (raw)
In-Reply-To: <DA3HXNN7HTD2.2NUKORU5V6CS2@kernel.org>
Hi, Michael, Thank you for your reviews.
On Fri, May 23, 2025 at 01:16:50PM +0200, Michael Walle wrote:
> Hi,
>
> > Add GD25LB512ME SPI-NOR flash information
>
> Please have a look at [1].
>
> This flash supports SFDP, do you really need a new entry in the
> flashdb? Could you try without it?
>
> In any case, could you please dump the SFDP see [1], too.
>
> [1] https://docs.kernel.org/driver-api/mtd/spi-nor.html
>
> -michael
I was following the testing requirements from [1].
Before that, I have applied the patch:
"mtd: spi-nor: Add GD25LB512ME GigaDevice flash_info"
Because without this patch, the spi-nor device cannot be detected normally.
------------------------------- LOG ------------------------------------
root@localhost ~ # dmesg | grep -i spi
[ 10.199526] spi-nor spi0.0: supply vcc not found, using dummy regulator
[ 11.206477] spi-nor spi0.0: unrecognized JEDEC id bytes: c8 67 1a ff c8 67
[ 11.213691] spi-nor spi1.0: supply vcc not found, using dummy regulator
[ 12.220614] spi-nor spi1.0: unrecognized JEDEC id bytes: c8 67 1a ff c8 67
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
cat: /sys/bus/spi/devices/spi0.0/spi-nor/partname: No such file or directory
Testing output atfer that patch:
------------------------------------------------------------------------
This flash is populated on the SG2042 Pioneer board and was tested at
100MHz frequency using the spi-sg2044-nor SPI controller.
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
gd25lb512me
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c8671a
root@localhost ~ # cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
gigadevice
root@localhost ~ # xxd -p /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
53464450060102ff00060110300000ffc8000103900000ff84000102c000
00ffffffffffffffffffffffffffffffffffe520eaffffffff1f44eb086b
003b00bbfeffffffffff00ffffff44eb0c200f5210d800ffd531b1fe83d6
1458ec6006337a757a7504bdd55c2906740008500001ffffffffffffffff
ffffffffffffffffffffffffffffffffffffffffffffffff002050169df9
8156d9c8ffffffffffffffffffffffffffffffffffffffffffffffffffff
fffffffffffffffffffffffff38ff0ff215cdcff
root@localhost ~ # sha256sum /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
859eb314b0500aa3e3dc5a1ad514f1013387c7aaa40147ed2d616ffc4b6d851c /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
root@localhost ~ # #Dump debugfs data
root@localhost ~ # cat /sys/kernel/debug/spi-nor/spi0.0/capabilities
Supported read modes by the flash
1S-1S-1S
opcode 0x13
mode cycles 0
dummy cycles 0
1S-1S-4S
opcode 0x6c
mode cycles 0
dummy cycles 8
1S-4S-4S
opcode 0xec
mode cycles 2
dummy cycles 4
4S-4S-4S
opcode 0xec
mode cycles 2
dummy cycles 4
Supported page program modes by the flash
1S-1S-1S
opcode 0x12
1S-1S-4S
opcode 0x34
1S-4S-4S
opcode 0x3e
root@localhost ~ # cat /sys/kernel/debug/spi-nor/spi0.0/params
name gd25lb512me
id c8 67 1a ff c8 67
size 64.0 MiB
write size 1
page size 256
address nbytes 4
flags HAS_SR_TB | 4B_OPCODES | HAS_4BAIT | HAS_LOCK | HAS_16BIT_SR | SOFT_RESET
opcodes
read 0x13
dummy cycles 0
erase 0x21
program 0x12
8D extension none
protocols
read 1S-1S-1S
write 1S-1S-1S
register 1S-1S-1S
erase commands
21 (4.00 KiB) [1]
5c (32.0 KiB) [2]
dc (64.0 KiB) [3]
c7 (64.0 MiB)
sector map
region (in hex) | erase mask | overlaid
------------------+------------+----------
00000000-03ffffff | [ 1 ] | no
root@localhost ~ # dd if=/dev/urandom of=./spi_test bs=1M count=2
2+0 records in
2+0 records out
2097152 bytes (2.1 MB, 2.0 MiB) copied, 0.0279486 s, 75.0 MB/s
root@localhost ~ # mtd_debug erase /dev/mtd0 0 2097152
Erased 2097152 bytes from address 0x00000000 in flash
root@localhost ~ # mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
root@localhost ~ # hexdump spi_read
0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0200000
root@localhost ~ # sha256sum spi_read
4bda3a28f4ffe603c0ec1258c0034d65a1a0d35ab7bd523a834608adabf03cc5 spi_read
root@localhost ~ # mtd_debug write /dev/mtd0 0 2097152 spi_test
Copied 2097152 bytes from spi_test to address 0x00000000 in flash
root@localhost ~ # mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
root@localhost ~ # sha256sum spi*
a2ebfaebe38974847a4efb628b29a72f1d50e78c17318869d8954b033dc32e5d spi_read
a2ebfaebe38974847a4efb628b29a72f1d50e78c17318869d8954b033dc32e5d spi_test
root@localhost ~ # mtd_debug info /dev/mtd0
mtd.type = MTD_NORFLASH
mtd.flags = MTD_CAP_NORFLASH
mtd.size = 67108864 (64M)
mtd.erasesize = 4096 (4K)
mtd.writesize = 1
mtd.oobsize = 0
regions = 0
------------------------------------------------------------------------
Best regards,
Zixian
next prev parent reply other threads:[~2025-05-23 16:45 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-05-23 10:54 [PATCH 0/3] spi: sophgo: Add SPI NOR controller for SG2042 Zixian Zeng
2025-05-23 10:54 ` Zixian Zeng
2025-05-23 10:54 ` Zixian Zeng
2025-05-23 10:54 ` [PATCH 1/3] dt-bindings: spi: Add bindings for SOPHGO SG2042 Zixian Zeng
2025-05-23 10:54 ` Zixian Zeng
2025-05-23 10:54 ` Zixian Zeng
2025-05-23 11:33 ` Krzysztof Kozlowski
2025-05-23 11:33 ` Krzysztof Kozlowski
2025-05-23 11:33 ` Krzysztof Kozlowski
2025-05-23 13:31 ` Zixian Zeng
2025-05-23 13:31 ` Zixian Zeng
2025-05-23 13:31 ` Zixian Zeng
2025-05-23 12:22 ` Rob Herring (Arm)
2025-05-23 12:22 ` Rob Herring (Arm)
2025-05-23 12:22 ` Rob Herring (Arm)
2025-05-23 10:54 ` [PATCH 2/3] mtd: spi-nor: Add GD25LB512ME GigaDevice flash_info Zixian Zeng
2025-05-23 10:54 ` Zixian Zeng
2025-05-23 10:54 ` Zixian Zeng
2025-05-23 11:16 ` Michael Walle
2025-05-23 11:16 ` Michael Walle
2025-05-23 11:16 ` Michael Walle
2025-05-23 16:18 ` Zixian Zeng [this message]
2025-05-23 16:18 ` Zixian Zeng
2025-05-23 16:18 ` Zixian Zeng
2025-05-27 16:30 ` Pratyush Yadav
2025-05-27 16:30 ` Pratyush Yadav
2025-05-27 16:30 ` Pratyush Yadav
2025-05-23 10:54 ` [PATCH 3/3] riscv: dts: sophgo: Add SPI NOR node for SG2042 Zixian Zeng
2025-05-23 10:54 ` Zixian Zeng
2025-05-23 10:54 ` Zixian Zeng
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=aDCf84cRw0tmcAbm@calculate \
--to=sycamoremoon376@gmail.com \
--cc=alex@ghiti.fr \
--cc=aou@eecs.berkeley.edu \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dlan@gentoo.org \
--cc=inochiama@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-riscv@lists.infradead.org \
--cc=linux-spi@vger.kernel.org \
--cc=looong.bin@gmail.com \
--cc=miquel.raynal@bootlin.com \
--cc=mwalle@kernel.org \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=pratyush@kernel.org \
--cc=richard@nod.at \
--cc=robh@kernel.org \
--cc=sophgo@lists.linux.dev \
--cc=tudor.ambarus@linaro.org \
--cc=unicorn_wang@outlook.com \
--cc=vigneshr@ti.com \
--cc=ziyao@disroot.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.