Re: [PATCH v7 00/22] Basic clock, reset & device tree support for StarFive JH7110 RISC-V SoC

[Hal Feng <hal.feng@starfivetech.com>]

On Sun, 2 Apr 2023 20:19:41 +0100, Conor Dooley wrote:
> Hey Hal,
> 
> On Sat, Apr 01, 2023 at 07:19:12PM +0800, Hal Feng wrote:
>> This patch series adds basic clock, reset & DT support for StarFive
>> JH7110 SoC.
>> 
>> @Stephen and @Conor, I have made this series start with the shared
>> dt-bindings, so it will be easier to merge.
> 
> Thanks. I probably should have asked for that, makes my life easier
> that's for sure!

My pleasure.

> 
>> @Conor, patch 1, 2, 16~21 were already in your branch. Patch 22 is the
>> same with the patch [1] I submitted before, which you had accepted but
>> not merge it into your branch.
> 
> I hadn't merged that into anywhere, so I just went and dropped the
> original incarnation of that branch and have re-created it.
> I don't recall there being a maintainers pattern error (from running
> scripts/get_maintainer.pl --self-test=patterns) with what I had done in
> my branch, but with your patch 1 applied I see one. To save myself a
> complaint from LKP, I stripped out the MAINTAINERS bits from patch 1
> into their own patch that can go with the clock/reset bits.
> 
> I squashed 22 into "riscv: dts: starfive: Add initial StarFive JH7110
> device tree" since there's no reason to add something knowingly
> incorrect IMO.
> 
> I've gone and pushed out the following as riscv-jh7110_initial_dts:
> riscv: dts: starfive: Add StarFive JH7110 VisionFive 2 board device
> riscv: dts: starfive: Add StarFive JH7110 pin function definitions
> riscv: dts: starfive: Add initial StarFive JH7110 device tree
> dt-bindings: riscv: Add SiFive S7 compatible
> dt-bindings: interrupt-controller: Add StarFive JH7110 plic
> dt-bindings: timer: Add StarFive JH7110 clint
> dt-bindings: clock: Add StarFive JH7110 always-on clock and reset generator
> dt-bindings: clock: Add StarFive JH7110 system clock and reset generator
> 
> And the rest as riscv-jh7110_clk_reset:
> MAINTAINERS: generalise StarFive clk/reset entries

For this patch, I find something to improve.
1. Could you please help me sort the StarFive entries in MAINTAINERS?
"STARFIVE JH71X0 CLOCK DRIVERS" should be added after
"STARFIVE JH7110 MMC/SD/SDIO DRIVER".

2. A "S" should be added at the end of
"STARFIVE JH7100 RESET CONTROLLER DRIVER".

I have tested your branch and have no comments on the other patches.

> reset: starfive: Add StarFive JH7110 reset driver
> clk: starfive: Add StarFive JH7110 always-on clock driver
> clk: starfive: Add StarFive JH7110 system clock driver
> reset: starfive: jh71x0: Use 32bit I/O on 32bit registers
> reset: starfive: Rename "jh7100" to "jh71x0" for the common code
> reset: starfive: Extract the common JH71X0 reset code
> reset: starfive: Factor out common JH71X0 reset code
> reset: Create subdirectory for StarFive drivers
> reset: starfive: Replace SOC_STARFIVE with ARCH_STARFIVE
> clk: starfive: Rename "jh7100" to "jh71x0" for the common code
> clk: starfive: Rename clk-starfive-jh7100.h to clk-starfive-jh71x0.h
> clk: starfive: Factor out common JH7100 and JH7110 code
> clk: starfive: Replace SOC_STARFIVE with ARCH_STARFIVE
> dt-bindings: clock: Add StarFive JH7110 always-on clock and reset generator
> dt-bindings: clock: Add StarFive JH7110 system clock and reset generator
> 
> <https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux.git/refs>
> 
> As it looks like everything has been resolved in terms of comments on
> v6, provided LKP doesn't complain or people don't spot something else,
> my plan is to send Stephen a PR around Wednesday for the driver bits.

Thanks for your work.

Best regards,
Hal

> 
> Please LMK if I screwed up anything,
> Conor.