From: "H. Nikolaus Schaller" <hns@goldelico.com>
To: Paul Boddie <paul@boddie.org.uk>,
Paul Cercueil <paul@crapouillou.net>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Ralf Baechle <ralf@linux-mips.org>,
Paul Burton <paulburton@kernel.org>,
"H. Nikolaus Schaller" <hns@goldelico.com>,
Miquel Raynal <miquel.raynal@bootlin.com>,
Andi Kleen <ak@linux.intel.com>,
Kees Cook <keescook@chromium.org>,
Krzysztof Kozlowski <krzk@kernel.org>
Cc: devicetree@vger.kernel.org, linux-mips@vger.kernel.org,
linux-kernel@vger.kernel.org, letux-kernel@openphoenux.org,
kernel@pyra-handheld.com
Subject: [PATCH v3 0/6] MIPS: Fixes and improvements for CI20 board (JZ4780)
Date: Sun, 16 Feb 2020 21:20:54 +0100 [thread overview]
Message-ID: <cover.1581884459.git.hns@goldelico.com> (raw)
V3:
* dropped "drm: ingenic-drm: add MODULE_DEVICE_TABLE" because it will be resubmitted
with a HDMI driver solution
* added Cc: stable@vger.kernel.org where appropriate (suggested by Paul Cercueil <paul@crapouillou.net>)
* squashed all other DTS and CONFIG changes into single patches (suggested by Paul Cercueil <paul@crapouillou.net>)
PATCH V2 2020-02-14 17:10:33:
* dropped "net: davicom: dm9000: allow to pass MAC address through mac_addr module parameter"
from this series because it goes through the netdev tree
(suggested by Andrew Lunn <andrew@lunn.ch>)
* added a "fixes:" for "MIPS: DTS: CI20: fix PMU definitions for ACT8600"
and "MIPS: DTS: CI20: fix interrupt for pcf8563 RTC"
(suggested by Andreas Kemnade <andreas@kemnade.info>)
* "i2c: jz4780: silence log flood on txabrt" dropped because it is
replaced by a new version in v5.6 by Wolfram Sang <wsa@the-dreams.de>
PATCH V1 2020-02-11 22:41:43:
This patch set provides several improvements for the CI20 board:
* suppress warnings from i2c if device is not responding
* make ingenic-drm found through DT
* allow davicom dm9000 ethernet controller to use MAC address provided by U-Boot
* fix #include in jz4780.dtsi
* configure for loadable kernel modules
* add DTS for IR sensor and SW1 button
* configure so that LEDs, IR sensor, SW1 button have drivers
* fix DTS for ACT8600 PMU and configure driver
* fix interrupt of nxp,pcf8563
There is another patch set in our queue to add HDMI support on top of this work.
Signed-off-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Alex Smith (1):
MIPS: DTS: CI20: add DT node for IR sensor
H. Nikolaus Schaller (5):
MIPS: DTS: jz4780: add #includes for irq.h and gpio.h
MIPS: DTS: CI20: fix PMU definitions for ACT8600
MIPS: DTS: CI20: fix interrupt for pcf8563 RTC
MIPS: DTS: CI20: multiple DTS improvements
MIPS: CI20: defconfig: multiple improvements
arch/mips/boot/dts/ingenic/ci20.dts | 71 ++++++++++++++++++++------
arch/mips/boot/dts/ingenic/jz4780.dtsi | 2 +
arch/mips/configs/ci20_defconfig | 21 ++++++++
3 files changed, 78 insertions(+), 16 deletions(-)
--
2.23.0
next reply other threads:[~2020-02-16 20:21 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-02-16 20:20 H. Nikolaus Schaller [this message]
2020-02-16 20:20 ` [PATCH v3 1/6] MIPS: DTS: jz4780: add #includes for irq.h and gpio.h H. Nikolaus Schaller
2020-02-28 14:33 ` Paul Cercueil
2020-02-16 20:20 ` [PATCH v3 2/6] MIPS: DTS: CI20: add DT node for IR sensor H. Nikolaus Schaller
2020-02-16 20:20 ` [PATCH v3 3/6] MIPS: DTS: CI20: fix PMU definitions for ACT8600 H. Nikolaus Schaller
2020-02-28 14:34 ` Paul Cercueil
2020-02-28 14:40 ` H. Nikolaus Schaller
2020-02-16 20:20 ` [PATCH v3 4/6] MIPS: DTS: CI20: fix interrupt for pcf8563 RTC H. Nikolaus Schaller
2020-02-16 20:20 ` [PATCH v3 5/6] MIPS: DTS: CI20: multiple DTS improvements H. Nikolaus Schaller
2020-02-28 14:36 ` Paul Cercueil
2020-02-28 14:42 ` H. Nikolaus Schaller
2020-02-28 14:50 ` Paul Cercueil
2020-02-16 20:21 ` [PATCH v3 6/6] MIPS: CI20: defconfig: multiple improvements H. Nikolaus Schaller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=cover.1581884459.git.hns@goldelico.com \
--to=hns@goldelico.com \
--cc=ak@linux.intel.com \
--cc=devicetree@vger.kernel.org \
--cc=keescook@chromium.org \
--cc=kernel@pyra-handheld.com \
--cc=krzk@kernel.org \
--cc=letux-kernel@openphoenux.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=miquel.raynal@bootlin.com \
--cc=paul@boddie.org.uk \
--cc=paul@crapouillou.net \
--cc=paulburton@kernel.org \
--cc=ralf@linux-mips.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.