From: sashiko-bot@kernel.org
To: "Yosry Ahmed" <yosry@kernel.org>
Cc: kvm@vger.kernel.org
Subject: Re: [PATCH v2 11/29] KVM: SVM: Only flush the fallback ASID when used by a different vCPU
Date: Thu, 08 Oct 2026 00:33:14 +0000 [thread overview]
Message-ID: <sashiko-outbox-163474@kernel.org> (raw)
In-Reply-To: <20261008001425.2458927-12-yosry@kernel.org>
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Low] kvm: data race on sd->fallback_asid_vcpu between pre_svm_run and svm_vcpu_free
--
commit aa8eca89b8d60f642d17b3f8439f52f2e1ae951d
Author: Yosry Ahmed <yosry@kernel.org>
KVM: SVM: Only flush the fallback ASID when used by a different vCPU
This commit optimizes the fallback ASID flushing logic by only flushing
when the last vCPU that used the fallback ASID on the pCPU changes. It
adds a per-CPU tracker fallback_asid_vcpu to determine when this occurs.
> diff --git a/arch/x86/kvm/svm/svm.c b/arch/x86/kvm/svm/svm.c
> index 8f27722bc4faf..0dbb1962d32b6 100644
> --- a/arch/x86/kvm/svm/svm.c
> +++ b/arch/x86/kvm/svm/svm.c
[ ... ]
> @@ -1422,6 +1424,11 @@ static void svm_vcpu_free(struct kvm_vcpu *vcpu)
> svm_vcpu_free_msrpm(svm->msrpm);
>
> free_asid(svm->asid);
> +
> + for_each_possible_cpu(cpu) {
> + sd = per_cpu_ptr(&svm_data, cpu);
> + cmpxchg(&sd->fallback_asid_vcpu, vcpu, NULL);
> + }
> }
[ ... ]
> @@ -3884,8 +3892,11 @@ static int pre_svm_run(struct kvm_vcpu *vcpu)
> if (is_sev_guest(vcpu))
> return pre_sev_run(svm, vcpu->cpu);
>
> - if (unlikely(svm->vmcb->control.asid == fallback_asid))
> + if (unlikely(svm->vmcb->control.asid == fallback_asid &&
> + sd->fallback_asid_vcpu != vcpu)) {
> vmcb_set_flush_asid(svm->vmcb);
> + sd->fallback_asid_vcpu = vcpu;
[Severity: Low]
Will this concurrent access to sd->fallback_asid_vcpu trigger a KCSAN data
race splat?
In svm_vcpu_free(), when a vCPU is being destroyed, it iterates over all
physical CPUs and modifies sd->fallback_asid_vcpu via cmpxchg() across CPUs.
Concurrently, another vCPU running on one of those CPUs will execute
pre_svm_run() and perform plain reads and writes of its local
sd->fallback_asid_vcpu.
Per the LKMM (C11 memory model), if an atomic RMW is used on one side
of a concurrent access, at least one side must use READ_ONCE() or
WRITE_ONCE() to prevent the compiler from fusing loads or reordering
plain stores.
Should the reads and writes in pre_svm_run() use READ_ONCE() and
WRITE_ONCE() to avoid this race?
> + }
>
> return 0;
> }
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261008001425.2458927-1-yosry@kernel.org?part=11
next prev parent reply other threads:[~2026-10-08 0:33 UTC|newest]
Thread overview: 38+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-08 0:13 [PATCH v2 00/29] KVM: nSVM: Optimize nSVM TLB flushes Yosry Ahmed
2026-10-08 0:13 ` [PATCH v2 01/29] KVM: nSVM: Flush the TLB after forcefully leaving nested Yosry Ahmed
2026-10-08 0:13 ` [PATCH v2 02/29] KVM: SVM: Document number of ASIDs CPUID setting Yosry Ahmed
2026-10-08 0:13 ` [PATCH v2 03/29] KVM: VMX: Generalize VPID allocation to be vendor-neutral Yosry Ahmed
2026-10-08 0:30 ` sashiko-bot
2026-10-08 0:14 ` [PATCH v2 04/29] KVM: x86/mmu: Support specifying reserved TLB tags Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 05/29] KVM: SVM: Add helpers to set/clear ASID flush in VMCB Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 06/29] KVM: SVM: Fallback to flush everything if FLUSHBYASID is not available Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 07/29] KVM: SEV: Do ASID initialization at VMCB initialization Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 08/29] KVM: SEV: Expose sev_get_asid() outside of sev.c Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 09/29] KVM: SEV: Explicitly initialize the per vCPU ASID on SEV VM migration Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 10/29] KVM: SVM: Use a static ASID per vCPU Yosry Ahmed
2026-10-08 0:30 ` sashiko-bot
2026-10-08 0:14 ` [PATCH v2 11/29] KVM: SVM: Only flush the fallback ASID when used by a different vCPU Yosry Ahmed
2026-10-08 0:33 ` sashiko-bot [this message]
2026-10-08 0:14 ` [PATCH v2 12/29] KVM: nSVM: Drop svm->nested.initialized Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 13/29] KVM: nSVM: Add a placeholder ASID for L2 Yosry Ahmed
2026-10-08 0:42 ` sashiko-bot
2026-10-08 0:14 ` [PATCH v2 14/29] KVM: x86: hyper-v: Rename kvm_hv_vcpu_purge_flush_tlb() Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 15/29] KVM: x86: hyper-v: Allow purging all TLB flush FIFOs Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 16/29] KVM: nSVM: Flush both L1 and L2 ASIDs on KVM_REQ_TLB_FLUSH Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 17/29] KVM: nSVM: Always switch VMCB before leaving guest mode Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 18/29] KVM: nSVM: Split nested_svm_transition_tlb_flush() into entry/exit fns Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 19/29] KVM: nSVM: Service local TLB flushes before nested transitions Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 20/29] KVM: x86: Add KVM_REQ_MMU_SYNC_ALL_ROOTS Yosry Ahmed
2026-10-08 3:29 ` Lai Jiangshan
2026-10-08 0:14 ` [PATCH v2 21/29] KVM: nSVM: Handle nested TLB flush requests through TLB_CONTROL Yosry Ahmed
2026-10-08 0:36 ` sashiko-bot
2026-10-08 0:14 ` [PATCH v2 22/29] KVM: nSVM: Flush the TLB if L1 changes L2's ASID in vmcb12 Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 23/29] KVM: nSVM: Do not reset TLB_CONTROL in vmcb02 on nested VM-Enter Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 24/29] KVM: x86/mmu: Rename __kvm_mmu_invalidate_addr() to kvm_mmu_sync_addr() Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 25/29] KVM: x86/mmu: Refactor kvm_mmu_invlpg() to allow skipping the GVA flush Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 26/29] KVM: nSVM: Flush L2's ASID when emulating INVLPGA Yosry Ahmed
2026-10-08 0:45 ` sashiko-bot
2026-10-08 0:14 ` [PATCH v2 27/29] KVM: nSVM: Flush the ASID on nested transitions if shared by L1 and L2 Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 28/29] KVM: nSVM: Use different ASIDs for " Yosry Ahmed
2026-10-08 0:14 ` [PATCH v2 29/29] KVM: selftests: Add a test for nested TLB flushes Yosry Ahmed
2026-10-08 0:35 ` sashiko-bot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=sashiko-outbox-163474@kernel.org \
--to=sashiko-bot@kernel.org \
--cc=kvm@vger.kernel.org \
--cc=sashiko-reviews@lists.linux.dev \
--cc=yosry@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.