[PATCH v4 00/12] Enable more nodes for the Xperia 10 III

[PATCH v4 00/12] Enable more nodes for the Xperia 10 III

[erebion]

Enable some more nodes for the Xperia 10 III.

Signed-off-by: erebion <erebion@erebion.eu>
---
Changes in v4:
- &pm6150l_flash: fix extra zero for led-max-microamp value accidentally added in v3 (this was setting the max value 10x to high), remove Lua's Reviewed-by
- rename touch-en-regulator patch: fix rebase mishap and remove a regulator that's not part of this patch series, remove Konrad's Reviewed-by
- IPA: remove redundant properties that are now set in sm6350-lena board DTS, remove Luca's Reviewed-by
- fix pm7250b thermals after a rebase mishap
- pm8350: disable PON, as pm6350 already has it enabled, remove Konrad's Reviewed-by
- rear_cam_sensor: fix gpio to use correct one
- remove includes that aren't actually used
- re-order alphabetically: &pm6150l_adc before &pm6150l_gpios
- remove a superfluous tab at the closing brace of rear-cam-flash-therm@2
- enable remaining i2c busses: fix rebase mishap
- fix firmware paths to use upper-case "Sony" instead of lower-case "sony" for consistency with other DTs, reset Luca's Reviewed-by
- remove rear_cam_sensor, as it does not work and I haven't found the issue, will submit later when I get it actually working
- Link to v3: https://patch.msgid.link/20261102-pdx213-upstream-3-v3-0-cdc3be96d257@erebion.eu

Changes in v3:
- re-order some properties, generic properties first, then qcom,*
- &pm6150l_flash: fix led-max-microamp value
- rename touch-en-regulator to regulator-touch-en (to keep any future fixed-regulator sorted together as well)
- Bluetooth: remove incorrect property that does not exist
- Bluetooth, &qup_uart1_cts: do not overwrite a bias-disable with bias-bus-hold as it is not necessary
- &pm7250b_vbus: fix regulator-max-microamp value
- Remove comment from reserved-memory as suggested by Konrad Dybcio
- Squashed the patch enabling IPA into the one enabling ADSP, CDSP & MPSS, as suggested by Luca Weiss (therefore not adding the Reviewed-by from Konrad Dybcio)
- Configure thermals for PMK8350, PM7250B, PM650L as used in pdx213
- Enable remaining i2c busses
- Link to v2: https://patch.msgid.link/20260926-pdx213-upstream-3-v2-0-b4612e3eb536@erebion.eu

Changes in v2:
- Remove panel_reset_pin that shouldn't be part of this patch series
- Remove incorrect reg from mpss
- Fix conflicting bias pinctrl, as pinctrl nodes from sm6350.dtsi already contain a bias-* property
- Fix incorrect unit name in &pmk8350_vadc
- Link to v1: https://patch.msgid.link/20260926-pdx213-upstream-3-v1-0-1609c18b5c1d@erebion.eu

To: Bjorn Andersson <andersson@kernel.org>
To: Konrad Dybcio <konradybcio@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

---
erebion (12):
      arm64: dts: qcom: sm6350-lena: Add flash LED
      arm64: dts: qcom: sm6350-lena: rename touch-en-regulator
      arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node
      arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS
      arm64: dts: qcom: sm6350-lena: Enable Bluetooth
      arm64: dts: qcom: sm6350-lena: Enable wifi
      arm64: dts: qcom: sm6350-lena: Enable PM7250B
      arm64: dts: qcom: sm6350-lena: Enable PMK8350
      arm64: dts: qcom: sm6350-lena: Add PM7250B thermals
      arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals
      arm64: dts: qcom: sm6350-lena: Add PM6150L thermals
      arm64: dts: qcom: sm6350-lena: enable remaining i2c busses

 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 457 ++++++++++++++++++++-
 1 file changed, 456 insertions(+), 1 deletion(-)
---
base-commit: e5e04726cdd043e309677071ab1b65a4b18f422b
change-id: 20260829-pdx213-upstream-3-d0b80f749b5b

Best regards,
--  
erebion <erebion@erebion.eu>

[PATCH v4 01/12] arm64: dts: qcom: sm6350-lena: Add flash LED

[erebion]

Add a node for the camera flash LED found on the Xperia 10 III

Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
 .../boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts      | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 6e2bbf4f060ac..4d78c500d00d3 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -4,9 +4,11 @@
  */
 /dts-v1/;
 
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm6350.dtsi"
+#include "pm6150l.dtsi"
 #include "pm6350.dtsi"
 
 / {
@@ -302,6 +304,19 @@ touchscreen@48 {
 	};
 };
 
+&pm6150l_flash {
+	status = "okay";
+
+	led-0 {
+		function = LED_FUNCTION_FLASH;
+		color = <LED_COLOR_ID_WHITE>;
+		led-sources = <1>;
+		led-max-microamp = <150000>;
+		flash-max-microamp = <1000000>;
+		flash-max-timeout-us = <1280000>;
+	};
+};
+
 &pm6350_gpios {
 	vol_down_n: vol-down-n-state {
 		pins = "gpio2";

-- 
2.53.0

[PATCH v4 02/12] arm64: dts: qcom: sm6350-lena: rename touch-en-regulator

[erebion]

rename touch-en-regulator -> regulator-touch-en, to
keep any future fixed-regulator sorted together

Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
 arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 4d78c500d00d3..ca44219e1a67d 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -46,7 +46,7 @@ key-volume-down {
 		};
 	};
 
-	touch_en_vreg: touch-en-regulator {
+	touch_en_vreg: regulator-touch-en {
 		compatible = "regulator-fixed";
 		regulator-name = "touch_en_vreg";
 		gpio = <&tlmm 10 GPIO_ACTIVE_HIGH>;

-- 
2.53.0

[PATCH v4 03/12] arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node

[erebion]

Adds the qcom,rmtfs-mem node required for the modem

Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
 arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index ca44219e1a67d..a393b7533ccbf 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -4,6 +4,7 @@
  */
 /dts-v1/;
 
+#include <dt-bindings/firmware/qcom,scm.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
@@ -54,6 +55,17 @@ touch_en_vreg: regulator-touch-en {
 
 		vin-supply = <&pm6350_l6>;
 	};
+
+	reserved-memory {
+		memory@fe901000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0xfe901000 0x0 0x280000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
+		};
+	};
 };
 
 &apps_rsc {

-- 
2.53.0

[PATCH v4 04/12] arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS

[erebion]

Enable the ADSP, CDSP, IPA and MPSS (Modem) nodes for the Xperia 10 III.

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 24 ++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index a393b7533ccbf..4066de20ea23a 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -68,6 +68,12 @@ memory@fe901000 {
 	};
 };
 
+&adsp {
+	firmware-name = "qcom/sm6350/Sony/pdx213/adsp.mbn";
+
+	status = "okay";
+};
+
 &apps_rsc {
 	regulators-0 {
 		compatible = "qcom,pm6350-rpmh-regulators";
@@ -291,6 +297,12 @@ pm6150l_bob: bob {
 	};
 };
 
+&cdsp {
+	firmware-name = "qcom/sm6350/Sony/pdx213/cdsp.mbn";
+
+	status = "okay";
+};
+
 &gpi_dma0 {
 	status = "okay";
 };
@@ -316,6 +328,18 @@ touchscreen@48 {
 	};
 };
 
+&ipa {
+	firmware-name = "qcom/sm6350/Sony/pdx213/ipa_fws.mbn";
+
+	status = "okay";
+};
+
+&mpss {
+	firmware-name = "qcom/sm6350/Sony/pdx213/modem.mbn";
+
+	status = "okay";
+};
+
 &pm6150l_flash {
 	status = "okay";
 

-- 
2.53.0

[PATCH v4 05/12] arm64: dts: qcom: sm6350-lena: Enable Bluetooth

[erebion]

Configure the required regulators for Bluetooth and enable it on the
Xperia 10 III.

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 96 ++++++++++++++++++++++
 1 file changed, 96 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 4066de20ea23a..ff07810c3a6a6 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -19,6 +19,10 @@ / {
 	qcom,msm-id = <434 0x10000>, <459 0x10000>;
 	qcom,board-id = <0x1000b 0>;
 
+	aliases {
+		serial1 = &uart1;
+	};
+
 	chosen {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -376,6 +380,32 @@ &qupv3_id_1 {
 	status = "okay";
 };
 
+/* UART1: HS UART for Bluetooth */
+&qup_uart1_rts {
+	/* We'll drive RTS, so no pull */
+	drive-strength = <2>;
+	/delete-property/ bias-pull-down;
+	bias-disable;
+};
+
+&qup_uart1_rx {
+	/*
+	 * Configure a pull-up on RX. This is needed to avoid
+	 * garbage data when the TX pin of the Bluetooth module is
+	 * in tri-state (module powered off or not driving the
+	 * signal yet).
+	 */
+	/delete-property/ bias-disable;
+	bias-pull-up;
+};
+
+&qup_uart1_tx {
+	/* We'll drive TX, so no pull */
+	drive-strength = <2>;
+	/delete-property/ bias-pull-up;
+	bias-disable;
+};
+
 &sdc2_off_state {
 	sd-cd-pins {
 		pins = "gpio94";
@@ -419,6 +449,72 @@ ts_int_default: ts-int-default-state {
 		drive-strength = <2>;
 		bias-disable;
 	};
+
+	qup_uart1_sleep_cts: qup-uart1-sleep-cts-state {
+		pins = "gpio61";
+		function = "gpio";
+		/*
+		 * Configure a bias-bus-hold on CTS to lower power
+		 * usage when Bluetooth is turned off. Bus hold will
+		 * maintain a low power state regardless of whether
+		 * the Bluetooth module drives the pin in either
+		 * direction or leaves the pin fully unpowered.
+		 */
+		bias-bus-hold;
+	};
+
+	qup_uart1_sleep_rts: qup-uart1-sleep-rts-state {
+		pins = "gpio62";
+		function = "gpio";
+		/*
+		 * Configure pull-down on RTS. As RTS is active low
+		 * signal, pull it low to indicate the BT SoC that it
+		 * can wakeup the system anytime from suspend state by
+		 * pulling RX low (by sending wakeup bytes).
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart1_sleep_rx: qup-uart1-sleep-rx-state {
+		pins = "gpio64";
+		function = "gpio";
+		/*
+		 * Configure a pull-up on RX. This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module
+		 * is floating which may cause spurious wakeups.
+		 */
+		bias-pull-up;
+	};
+
+	qup_uart1_sleep_tx: qup-uart1-sleep-tx-state {
+		pins = "gpio63";
+		function = "gpio";
+		/*
+		 * Configure pull-up on TX when it isn't actively driven
+		 * to prevent BT SoC from receiving garbage during sleep.
+		 */
+		bias-pull-up;
+	};
+};
+
+&uart1 {
+	/delete-property/ interrupts;
+	interrupts-extended = <&intc GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
+			     <&tlmm 64 IRQ_TYPE_EDGE_FALLING>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-1 = <&qup_uart1_sleep_cts>, <&qup_uart1_sleep_rts>, <&qup_uart1_sleep_tx>, <&qup_uart1_sleep_rx>;
+
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3991-bt";
+		vddio-supply = <&pm6350_l11>;
+		vddxo-supply = <&pm6350_l7>;
+		vddrf-supply = <&pm6150l_l2>;
+		vddch0-supply = <&pm6150l_l10>;
+		firmware-name = "crnv32u.bin";
+	};
 };
 
 &usb_1 {

-- 
2.53.0

[PATCH v4 06/12] arm64: dts: qcom: sm6350-lena: Enable wifi

[erebion]

Configure regulators and enable it for the Xperia 10 III

Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
 arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index ff07810c3a6a6..becaf226af88c 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -541,3 +541,13 @@ &usb_1_qmpphy {
 
 	status = "okay";
 };
+
+&wifi {
+	vdd-0.8-cx-mx-supply = <&pm6350_l4>;
+	vdd-1.8-xo-supply = <&pm6350_l7>;
+	vdd-1.3-rfa-supply = <&pm6150l_l2>;
+	vdd-3.3-ch0-supply = <&pm6150l_l10>;
+	vdd-3.3-ch1-supply = <&pm6150l_l11>;
+
+	status = "okay";
+};

-- 
2.53.0

[PATCH v4 07/12] arm64: dts: qcom: sm6350-lena: Enable PM7250B

[erebion]

Enable PM7250B and some components on it for the Xperia 10 III.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 48 ++++++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index becaf226af88c..03af6aaefa66c 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -4,6 +4,10 @@
  */
 /dts-v1/;
 
+/* PM7250B is configured to use SID2/3 */
+#define PM7250B_SID 2
+#define PM7250B_SID1 3
+
 #include <dt-bindings/firmware/qcom,scm.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
@@ -11,6 +15,7 @@
 #include "sm6350.dtsi"
 #include "pm6150l.dtsi"
 #include "pm6350.dtsi"
+#include "pm7250b.dtsi"
 
 / {
 	model = "Sony Xperia 10 III";
@@ -372,6 +377,49 @@ &pm6350_resin {
 	status = "okay";
 };
 
+&pm7250b_adc {
+	channel@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		label = "charger_skin_therm";
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		qcom,ratiometric;
+	};
+
+	channel@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		label = "conn_therm";
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		qcom,ratiometric;
+	};
+};
+
+&pm7250b_adc_tm {
+	status = "okay";
+
+	charger-skin-therm@0 {
+		reg = <0>;
+		io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	conn-therm@1 {
+		reg = <1>;
+		io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pm7250b_vbus {
+	regulator-min-microamp = <500000>;
+	regulator-max-microamp = <1000000>;
+
+	status = "okay";
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };

-- 
2.53.0

[PATCH v4 08/12] arm64: dts: qcom: sm6350-lena: Enable PMK8350

[erebion]

Configure and enable nodes for PMK8350 on the Xperia 10 III.

The phone has two PMICs which have a PON block, disable the PMK8350
 PON and keep the PM6350 PON, as only one should be enabled.

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 34 ++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 03af6aaefa66c..361ed8ec96c81 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -8,7 +8,11 @@
 #define PM7250B_SID 2
 #define PM7250B_SID1 3
 
+/* PMK8350 (in reality a PMK8003) is configured to use SID6 instead of 0 */
+#define PMK8350_SID 6
+
 #include <dt-bindings/firmware/qcom,scm.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
@@ -16,6 +20,7 @@
 #include "pm6150l.dtsi"
 #include "pm6350.dtsi"
 #include "pm7250b.dtsi"
+#include "pmk8350.dtsi"
 
 / {
 	model = "Sony Xperia 10 III";
@@ -420,6 +425,35 @@ &pm7250b_vbus {
 	status = "okay";
 };
 
+&pmk8350_adc_tm {
+	status = "okay";
+
+	xo-therm@0 {
+		reg = <0>;
+		io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
+		qcom,hw-settle-time-us = <200>;
+		qcom,ratiometric;
+	};
+};
+
+&pmk8350_pon {
+	status = "disabled";
+};
+
+&pmk8350_rtc {
+	status = "okay";
+};
+
+&pmk8350_vadc {
+	channel@644 {
+		reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
+		label = "xo_therm";
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+	};
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };

-- 
2.53.0

[PATCH v4 09/12] arm64: dts: qcom: sm6350-lena: Add PM7250B thermals

[erebion]

Configure the thermals for the chg-skin-thermal and conn-therm thermistors connected to
PM7250B.

The trip points can really only be considered as placeholders, more
configuration with cooling etc. can be added later.

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 26 ++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 361ed8ec96c81..d37f5090dbfa7 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -80,6 +80,32 @@ memory@fe901000 {
 			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
 		};
 	};
+
+	thermal-zones {
+		chg-skin-thermal {
+			thermal-sensors = <&pm7250b_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		conn-thermal {
+			thermal-sensors = <&pm7250b_adc_tm 1>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+	};
 };
 
 &adsp {

-- 
2.53.0

[PATCH v4 10/12] arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals

[erebion]

Configure the thermals for the xo-thermal thermistor connected to
PMK8350.

The trip points can really only be considered as placeholders, more
configuration with cooling etc. can be added later.

Signed-off-by: erebion <erebion@erebion.eu>
---
 arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index d37f5090dbfa7..79097ae409bab 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -105,6 +105,18 @@ active-config0 {
 				};
 			};
 		};
+
+		xo-thermal {
+			thermal-sensors = <&pmk8350_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
 	};
 };
 

-- 
2.53.0

[PATCH v4 11/12] arm64: dts: qcom: sm6350-lena: Add PM6150L thermals

[erebion]

Configure the thermals for the PA_THERM1, MSM_THERM, PA_THERM0,
RFC_CAM_THERM, CAM_FLASH_THERM and QUIET_THERM thermistors connected to
PM6150L.

Due to hardware constraints we can only register 4 zones with
pm6150l_adc_tm, the other 2 we can register via generic-adc-thermal.

The trip points can really only be considered as placeholders, more
configuration with cooling etc. can be added later.

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 160 +++++++++++++++++++++
 1 file changed, 160 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 79097ae409bab..d7a5df04a296c 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -61,6 +61,13 @@ key-volume-down {
 		};
 	};
 
+	msm_therm_sensor: thermal-sensor-msm {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&pm6150l_adc ADC5_AMUX_THM2_100K_PU>;
+		io-channel-names = "sensor-channel";
+	};
+
 	touch_en_vreg: regulator-touch-en {
 		compatible = "regulator-fixed";
 		regulator-name = "touch_en_vreg";
@@ -106,6 +113,74 @@ active-config0 {
 			};
 		};
 
+		pa0-thermal {
+			thermal-sensors = <&pm6150l_adc_tm 1>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		pa1-thermal {
+			thermal-sensors = <&pm6150l_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		quiet-thermal {
+			thermal-sensors = <&pm6150l_adc_tm 3>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		rfc-flash-thermal {
+			thermal-sensors = <&pm6150l_adc_tm 2>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		sdm-skin-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&msm_therm_sensor>;
+
+			trips {
+				trip0 {
+					temperature = <45000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <55000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
 		xo-thermal {
 			thermal-sensors = <&pmk8350_adc_tm 0>;
 
@@ -392,6 +467,83 @@ &mpss {
 	status = "okay";
 };
 
+&pm6150l_adc {
+	pinctrl-0 = <&pm6150l_adc_default>;
+	pinctrl-names = "default";
+
+	channel@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		label = "pa_therm1";
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		qcom,ratiometric;
+	};
+
+	channel@4e {
+		reg = <ADC5_AMUX_THM2_100K_PU>;
+		label = "msm_therm";
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		qcom,ratiometric;
+	};
+
+	channel@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		label = "pa_therm0";
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		qcom,ratiometric;
+	};
+
+	channel@54 {
+		reg = <ADC5_GPIO3_100K_PU>;
+		label = "rear_cam_flash_therm";
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		qcom,ratiometric;
+	};
+
+	channel@55 {
+		reg = <ADC5_GPIO4_100K_PU>;
+		label = "quiet_therm";
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		qcom,ratiometric;
+	};
+};
+
+&pm6150l_adc_tm {
+	status = "okay";
+
+	pa-therm1@0 {
+		reg = <0>;
+		io-channels = <&pm6150l_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,hw-settle-time-us = <200>;
+		qcom,ratiometric;
+	};
+
+	pa-therm0@1 {
+		reg = <1>;
+		io-channels = <&pm6150l_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,hw-settle-time-us = <200>;
+		qcom,ratiometric;
+	};
+
+	rear-cam-flash-therm@2 {
+		reg = <2>;
+		io-channels = <&pm6150l_adc ADC5_GPIO3_100K_PU>;
+		qcom,hw-settle-time-us = <200>;
+		qcom,ratiometric;
+	};
+
+	quiet-therm@3 {
+		reg = <3>;
+		io-channels = <&pm6150l_adc ADC5_GPIO4_100K_PU>;
+		qcom,hw-settle-time-us = <200>;
+		qcom,ratiometric;
+	};
+};
+
 &pm6150l_flash {
 	status = "okay";
 
@@ -405,6 +557,14 @@ led-0 {
 	};
 };
 
+&pm6150l_gpios {
+	pm6150l_adc_default: adc-default-state {
+		pins = "gpio6", "gpio7", "gpio10";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		bias-high-impedance;
+	};
+};
+
 &pm6350_gpios {
 	vol_down_n: vol-down-n-state {
 		pins = "gpio2";

-- 
2.53.0

[PATCH v4 12/12] arm64: dts: qcom: sm6350-lena: enable remaining i2c busses

[erebion]

Enable all i2c busses where something is connected on this phone. Add
comments as placeholders for which components are still missing.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
 .../boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts   | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index d7a5df04a296c..ee65110f2c847 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -438,6 +438,13 @@ &gpi_dma1 {
 	status = "okay";
 };
 
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* PN553 NFC @ 28 */
+};
+
 &i2c8 {
 	clock-frequency = <400000>;
 	status = "okay";
@@ -455,6 +462,17 @@ touchscreen@48 {
 	};
 };
 
+&i2c10 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* PM8008 PMIC @ 8 and 9 */
+	/* SMB1395 PMIC @ 34 and 35 */
+	/* AW882xx amplifier @ 34 */
+	/* Foursemi FS16xx amplifier @ 35 */
+	/* FSA4480 Analog Audio Switch @ 42 */
+};
+
 &ipa {
 	firmware-name = "qcom/sm6350/Sony/pdx213/ipa_fws.mbn";
 

-- 
2.53.0

Re: [PATCH v4 02/12] arm64: dts: qcom: sm6350-lena: rename touch-en-regulator

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [High] arm64: dts: qcom: single-word handle used in Signed-off-by
  trailer
--

commit d12bf1b1dee33b26a5800faa94f2b6f60f9599de
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: rename touch-en-regulator
>
> rename touch-en-regulator -> regulator-touch-en, to
> keep any future fixed-regulator sorted together
>
> Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
Both the Author header and the Signed-off-by trailer use the single-word
handle "erebion" instead of a full real name, which does not satisfy the
Developer's Certificate of Origin requirements in
Documentation/process/submitting-patches.rst.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=2

Re: [PATCH v4 06/12] arm64: dts: qcom: sm6350-lena: Enable wifi

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [High] arm64: dts: qcom: Signed-off-by and Author use handle instead
  of real name
--

commit 24a3b1f3ecac1502767c6ab922369282c14e2622
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: Enable wifi
>
> Configure regulators and enable it for the Xperia 10 III
>
> Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
Both the Author header and the Signed-off-by trailer use the single-word
handle "erebion".  The Developer's Certificate of Origin in
Documentation/process/submitting-patches.rst requires a full real name
rather than a pseudonym or handle, so both fields need to be updated to
use a real name.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=6

Re: [PATCH v4 03/12] arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [High] arm64: dts: qcom: sm6350-lena: Signed-off-by uses handle
  instead of real name
--

commit a9ddce3144fad1d53145bd8e52ebb61fbdf78099
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node
>
> Adds the qcom,rmtfs-mem node required for the modem
>
> Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
The Author header and Signed-off-by trailer use the handle "erebion"
instead of a real name.  Under Documentation/process/submitting-patches.rst,
the Developer's Certificate of Origin requires a known real name rather
than a pseudonym or handle.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=3

Re: [PATCH v4 01/12] arm64: dts: qcom: sm6350-lena: Add flash LED

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [High] arm64: dts: qcom: username handle used in Signed-off-by and
  Author fields
--

commit 9d995ddc664157d72483c0a7caa443b691f53025
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: Add flash LED
>
> Add a node for the camera flash LED found on the Xperia 10 III
>
> Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
As reported by Bjorn Andersson on v2 [1], the Author and Signed-off-by
fields use a single-word handle ("erebion") rather than a full real
name, which does not satisfy the Developer's Certificate of Origin
requirements in Documentation/process/submitting-patches.rst.

[1] https://lore.kernel.org/r/arnF0u2F9ipfnNP-@zenbook

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=1

Re: [PATCH v4 10/12] arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [High] arm64: dts: qcom: Signed-off-by trailer uses handle instead of
  real name
--

commit 6202c1bff4c338ba19173eebbf9dc1a6bca1824f
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals
>
> Configure the thermals for the xo-thermal thermistor connected to
> PMK8350.
>
> The trip points can really only be considered as placeholders, more
> configuration with cooling etc. can be added later.
>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
The Author header and Signed-off-by trailer use the single-word handle
"erebion" instead of a real full name, which does not meet the Developer's
Certificate of Origin sign-off requirements in
Documentation/process/submitting-patches.rst.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=10

Re: [PATCH v4 09/12] arm64: dts: qcom: sm6350-lena: Add PM7250B thermals

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [High] arm64: dts: qcom: handle used instead of real name in
  Signed-off-by trailer
--

commit 35567a569045cf43924fdde8c95265a9820a48bb
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: Add PM7250B thermals
>
> Configure the thermals for the chg-skin-thermal and conn-therm thermistors connected to
> PM7250B.
>
> The trip points can really only be considered as placeholders, more
> configuration with cooling etc. can be added later.
>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
Should the Author header and Signed-off-by trailer use a real name instead of
the handle "erebion"?  Documentation/process/submitting-patches.rst requires
a real human name for the Developer's Certificate of Origin and does not
allow pseudonyms or handles.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=9

Re: [PATCH v4 08/12] arm64: dts: qcom: sm6350-lena: Enable PMK8350

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [High] arm64: dts: qcom: invalid handle in Signed-off-by trailer
--

commit acc7716614faf15423968aecc6a9f74285660459
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: Enable PMK8350
>
> Configure and enable nodes for PMK8350 on the Xperia 10 III.
>
> The phone has two PMICs which have a PON block, disable the PMK8350
>  PON and keep the PM6350 PON, as only one should be enabled.
>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
Per Documentation/process/submitting-patches.rst, the Signed-off-by
trailer and Author header must use a real human name rather than a
single-word handle or username.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=8

Re: [PATCH v4 07/12] arm64: dts: qcom: sm6350-lena: Enable PM7250B

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [High] arm64: dts: qcom: Signed-off-by trailer uses handle instead of
  real name
--

commit 77c2a693eb35ea890a4be634ad96dc8d86e34270
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: Enable PM7250B
>
> Enable PM7250B and some components on it for the Xperia 10 III.
>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
Documentation/process/submitting-patches.rst requires a known real human
name in the Signed-off-by trailer and Author header rather than a handle or
pseudonym, as required by the Developer's Certificate of Origin. Could this
be updated to use a real name?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=7

Re: [PATCH v4 12/12] arm64: dts: qcom: sm6350-lena: enable remaining i2c busses

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [High] arm64: dts: qcom: handle used instead of real name in
  Signed-off-by
--

commit fe7e98e46dac6038a81f144f88f59c95001cffd5
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: enable remaining i2c busses
>
> Enable all i2c busses where something is connected on this phone. Add
> comments as placeholders for which components are still missing.
>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
The Author and Signed-off-by fields use the handle "erebion" rather than a
full real name.  Under Documentation/process/submitting-patches.rst and the
Developer's Certificate of Origin, patches cannot be merged without a
sign-off using a known real identity.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=12

Re: [PATCH v4 11/12] arm64: dts: qcom: sm6350-lena: Add PM6150L thermals

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 3 potential
issues to consider:
- [High] arm64: dts: qcom: sm6350-lena: handle used in Author and
  Signed-off-by
- [Medium] arm64: dts: qcom: sm6350-lena: inconsistent RFC_CAM_THERM
  pinctrl and ADC setup
- [Low] arm64: dts: qcom: sm6350-lena: thermal-sensor-msm ordered by
  label not name
--

commit e42ff4c503ef1827973e7803bdff8b39d54aacf7
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: Add PM6150L thermals
>
> Configure the thermals for the PA_THERM1, MSM_THERM, PA_THERM0,
> RFC_CAM_THERM, CAM_FLASH_THERM and QUIET_THERM thermistors connected to
> PM6150L.
>
> Due to hardware constraints we can only register 4 zones with
> pm6150l_adc_tm, the other 2 we can register via generic-adc-thermal.
>
> The trip points can really only be considered as placeholders, more
> configuration with cooling etc. can be added later.
>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
Per Documentation/process/submitting-patches.rst, the Author header and
Signed-off-by trailer must use a real human name rather than an account
handle ("erebion").

> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index 79097ae409bab..d7a5df04a296c 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -61,6 +61,13 @@ key-volume-down {
>  		};
>  	};
>  
> +	msm_therm_sensor: thermal-sensor-msm {
> +		compatible = "generic-adc-thermal";
> +		#thermal-sensor-cells = <0>;
> +		io-channels = <&pm6150l_adc ADC5_AMUX_THM2_100K_PU>;
> +		io-channel-names = "sensor-channel";
> +	};
> +
>  	touch_en_vreg: regulator-touch-en {

[Severity: Low]
This isn't a bug, but devicetree coding style orders nodes without unit
addresses alphabetically by node name rather than label, so
thermal-sensor-msm should be placed after reserved-memory and before
thermal-zones.

[ ... ]

> @@ -392,6 +467,83 @@ &mpss {
>  	status = "okay";
>  };
>  
> +&pm6150l_adc {
> +	pinctrl-0 = <&pm6150l_adc_default>;
> +	pinctrl-names = "default";
> +
> +	channel@4d {
> +		reg = <ADC5_AMUX_THM1_100K_PU>;
> +		label = "pa_therm1";
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		qcom,ratiometric;
> +	};
> +
> +	channel@4e {
> +		reg = <ADC5_AMUX_THM2_100K_PU>;
> +		label = "msm_therm";
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		qcom,ratiometric;
> +	};
> +
> +	channel@4f {
> +		reg = <ADC5_AMUX_THM3_100K_PU>;
> +		label = "pa_therm0";
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		qcom,ratiometric;
> +	};
> +
> +	channel@54 {
> +		reg = <ADC5_GPIO3_100K_PU>;
> +		label = "rear_cam_flash_therm";
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		qcom,ratiometric;
> +	};
> +
> +	channel@55 {
> +		reg = <ADC5_GPIO4_100K_PU>;
> +		label = "quiet_therm";
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		qcom,ratiometric;
> +	};
> +};

[ ... ]

> @@ -405,6 +557,14 @@ led-0 {
>  	};
>  };
>  
> +&pm6150l_gpios {
> +	pm6150l_adc_default: adc-default-state {
> +		pins = "gpio6", "gpio7", "gpio10";
> +		function = PMIC_GPIO_FUNC_NORMAL;
> +		bias-high-impedance;
> +	};
> +};

[Severity: Medium]
Is the sixth thermistor (for rear camera) missing from pm6150l_adc, or
should gpio6 be dropped from pm6150l_adc_default?

The commit message describes six thermistors with two registered via
generic-adc-thermal, and pm6150l_adc_default configures three pins (gpio6,
gpio7, and gpio10) into high-impedance mode.  However, pm6150l_adc only
defines five channels (with only two gpio-backed inputs, channel@54 and
channel@55, omitting channel@53) and only one generic-adc-thermal sensor
(msm_therm_sensor) is registered.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=11

Re: [PATCH v4 04/12] arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential
issues to consider:
- [High] arm64: dts: qcom: Signed-off-by uses handle erebion instead of
  real name
- [Low] arm64: dts: qcom: sm6350-lena: inconsistent Sony firmware-name
  path
--

commit 242b8f170866c87626f6fca5aa977fc4b21bc731
Author: erebion <erebion@erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS
>
> Enable the ADSP, CDSP, IPA and MPSS (Modem) nodes for the Xperia 10 III.
>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
The Author and Signed-off-by lines use a handle ("erebion") instead of a
real human name, which does not meet the Developer's Certificate of Origin
requirements in Documentation/process/submitting-patches.rst.

> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index a393b7533ccbf..4066de20ea23a 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -68,6 +68,12 @@ memory@fe901000 {
>  	};
>  };
>  
> +&adsp {
> +	firmware-name = "qcom/sm6350/Sony/pdx213/adsp.mbn";
> +
> +	status = "okay";
> +};
> +
>  &apps_rsc {
>  	regulators-0 {
>  		compatible = "qcom,pm6350-rpmh-regulators";
> @@ -291,6 +297,12 @@ pm6150l_bob: bob {
>  	};
>  };
>  
> +&cdsp {
> +	firmware-name = "qcom/sm6350/Sony/pdx213/cdsp.mbn";
> +
> +	status = "okay";
> +};
> +
>  &gpi_dma0 {
>  	status = "okay";
>  };
> @@ -316,6 +328,18 @@ touchscreen@48 {
>  	};
>  };
>  
> +&ipa {
> +	firmware-name = "qcom/sm6350/Sony/pdx213/ipa_fws.mbn";
> +
> +	status = "okay";
> +};
> +
> +&mpss {
> +	firmware-name = "qcom/sm6350/Sony/pdx213/modem.mbn";
> +
> +	status = "okay";
> +};

[Severity: Low]
Should firmware-name for adsp, cdsp, ipa, and mpss use the platform
codename ("qcom/sm6350/Sony/lena/...") instead of "pdx213"?

Other Sony Xperia device trees in arch/arm64/boot/dts/qcom/, including
single-board files such as sm6375-sony-xperia-murray-pdx225.dts and
sm8550-sony-xperia-yodo-pdx234.dts, follow the
qcom/<soc>/Sony/<platform>/<file>.mbn convention standardized in commit
f0a577c3a807 ("arm64: dts: qcom: sm8350: sagami: Fix remoteproc firmware
path").

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=4

Re: [PATCH v4 02/12] arm64: dts: qcom: sm6350-lena: rename touch-en-regulator

[erebion]

[-- Attachment #1.1: Type: text/plain, Size: 1204 bytes --]



On 11/13/26 02:28, sashiko-bot@kernel.org wrote:
> Thank you for your contribution! Sashiko AI review found 1 potential
> issue to consider:
> - [High] arm64: dts: qcom: single-word handle used in Signed-off-by
>    trailer
> --
> 
> commit d12bf1b1dee33b26a5800faa94f2b6f60f9599de
> Author: erebion <erebion@erebion.eu>
> 
>> arm64: dts: qcom: sm6350-lena: rename touch-en-regulator
>>
>> rename touch-en-regulator -> regulator-touch-en, to
>> keep any future fixed-regulator sorted together
>>
>> Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
>> Signed-off-by: erebion <erebion@erebion.eu>
> 
> [Severity: High]
> Both the Author header and the Signed-off-by trailer use the single-word
> handle "erebion" instead of a full real name, which does not satisfy the
> Developer's Certificate of Origin requirements in
> Documentation/process/submitting-patches.rst.
> 

This was already discussed in v2... And why the hell does the bot now 
suddenly send me an email for every single patch in this patch series 
saying exactly the same?!

So annoying.


-- 
erebion

XMPP: erebion@erebion.eu

Accepted languages: German, English, Swedish, Norwegian, Danish


[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 236 bytes --]

Re: [PATCH v4 05/12] arm64: dts: qcom: sm6350-lena: Enable Bluetooth

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [High] arm64: dts: qcom: Signed-off-by and Author use handle instead
  of real name
--

commit a88dbe84a474608356cf7418da893f73d6055164
Author: erebion <erebion@erebion.eu>

> arm64: dts: qcom: sm6350-lena: Enable Bluetooth
>
> Configure the required regulators for Bluetooth and enable it on the
> Xperia 10 III.
>
> Signed-off-by: erebion <erebion@erebion.eu>

[Severity: High]
Could the Author header and Signed-off-by trailer use a real full name
instead of the handle "erebion"?  Documentation/process/submitting-patches.rst
requires a real human name to certify the Developer's Certificate of Origin.

Also, this isn't a bug, but the commit message says it configures the
regulators for Bluetooth, whereas the PM6350 and PM6150L regulators are
already defined in the board DTS and this patch only references their
phandles in the bluetooth node.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu?part=5